MPD D219ERU

D200ERU Series
Low Cost, 4:1 Input
Miniature, 2W SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
• 2W Output Power
• 4:1 Input Voltage Range
• 1,500 VDC Isolation
• Short Circuit Protected
• Miniature SIP Case
• Single & Dual Outputs
• 1.0 MH MTBF
• Industry Standard Pin-Out
• Low Low Cost!!
Parameter
Input Voltage Range
Conditions
Min.
Typ.
Max.
24 VDC Input
9.0
24.0
36.0
48 VDC Input
18.0
48.0
72.0
Reverse Polarity Input Current
Short Circuit Input Power
VDC
1.0
A
1,500
mW
Output
Typ.
Max.
Units
Output Voltage Accuracy
Parameter
±1.0
±3.0
%
Output Voltage Balance
±1.0
±2.0
%
Vin = Min to Max
±0.2
±0.75
%
Load Regulation
Iout = 10% to 100%
±0.5
±1.5
%
Ripple (20 MHz)
See Note 1
15
30
mV P - P
50
150
mV P - P
±0.03
%/°C
Max.
Units
Line Regulation
Conditions
Min.
Noise (20 MHz)
Output Power Protection
120
%
Temperature Coefficient
Output Short Circuit
RoHS Compliant
Units
Continuous (Autorecovery)
General
Parameter
Conditions
Isolation Voltage
Isolation Resistance
Min.
60 Seconds
1,500
500 VDC
1,000
Typ.
VDC
MΩ
Isolation Capacitance
100 kHz, 1V
65
Switching Frequency , Single Output
Iout = 100%
100
650
kHz
pF
Switching Frequency , Dual Output
Iout = 100%
200
400
kHz
Max.
Units
Environmental
Parameter
Conditions
Operating Temperature Range
Ambient
Storage Temperature Range
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Typ.
-40
+25
-55
Cooling
Humidity
Min.
+85
°C
+125
°C
95
%
Free Air Convection
RH, Non-condensing
Case Size
1.02 x 0.37 x 0.49 Inches (26.0 x 9.50 x 12.50 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
0.24 Oz (7.0g)
Reliability Specifications
Parameter
MTBF
Conditions
Min.
MIL HDBK 217F, 25°C, Gnd Benign
1.0
Conditions
Min.
Typ.
Max.
Units
MHours
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation
Typ.
Max.
24 VDC Input
-0.7
40.0
48 VDC Input
-0.7
80.0
1.5 mm From Case For 10 Sec
All Models
Units
VDC
300
°C
1,800
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Model
Number
D201ERU
D202ERU
D203ERU
D204ERU
D205ERU
D206ERU
D207ERU
D208ERU
D209ERU
D211ERU
D212ERU
D213ERU
D214ERU
D215ERU
D216ERU
D217ERU
D218ERU
D219ERU
Input
Output
Efficiency
Voltage Current
Current
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Typ)
24
9.0 - 36.0
114
35
3.3
500.0
50.0
73
24
9.0 - 36.0
111
35
5.0
400.0
40.0
75
24
9.0 - 36.0
107
35
9.0
222.0
22.0
78
24
9.0 - 36.0
102
35
12.0
167.0
16.0
82
24
9.0 - 36.0
103
35
15.0
133.0
13.0
81
24
9.0 - 36.0
110
35
±5.0
±200.0
±20.0
76
24
9.0 - 36.0
107
35
±9.0
±111.0
±11.0
78
24
9.0 - 36.0
102
35
±12.0
±83.0
±8.0
82
24
9.0 - 36.0
103
35
±15.0
±67.0
±7.0
81
48
18.0 - 72.0
58
15
3.3
500.0
50.0
72
48
18.0 - 72.0
55
15
5.0
400.0
40.0
76
48
18.0 - 72.0
53
15
9.0
222.0
22.0
78
48
18.0 - 72.0
51
15
12.0
167.0
16.0
81
48
18.0 - 72.0
52
15
15.0
133.0
13.0
80
48
18.0 - 72.0
55
15
±5.0
±200.0
±20.0
75
48
18.0 - 72.0
54
15
±9.0
±111.0
±11.0
77
48
18.0 - 72.0
51
15
±12.0
±83.0
±8.0
81
48
18.0 - 72.0
52
15
±15.0
±67.0
±7.0
80
Notes:
1. When measuring output ripple, it is recommended that an external ceramic capacitor
(approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output
units and from each output to common for dual output units.
2. These units should not be operated with a load under 10% of full load. Operation at
no-load may cause damage to the unit.
3. These converters are specified for
operation without external compoInput
Output
nents. However, in some applicaVin Capacitor
Vout Capacitor
tions the addition of input/output
capacitors will enhance stability and
reduce output ripple. Recommended 12 VDC
100 µF
5 VDC
47 µF
capacitor values are given at right.
100 µF
9 VDC
47 µF
Output ripple on single output units 15 VDC
may be further enhanced by using 24 VDC
10 µF
12 VDC
47 µF
the CS terminal (single output units 48 VDC
10 µF
15 VDC
47 µF
operated at 50% load or below
should use this function). A low ESR capacitor is connected between the CS pin and the
-Vout pin (the capcitor anode connected to the -Vout pin). Recommended capacitor
values are given in the table at right. If not used, the CS pin should be left open.
4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do
this, connect the load across the +Vout and -Vout outputs and float the output common.
5. The remote on/off control pin is referenced to
Min
Max
the -Vin pin. Input current to the pin should
<0.6 VDC to Open Circuit
be between 5 - 10 mA with a maximum of 20 On
mA.
Off
2.7 VDC
15.0 VDC
6. It is recommended that a fuse be used on the
input of a power supply for protection. See the Model Selection
table above for the correct rating.
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
500
500
500
500
500
200
200
200
200
200
200
200
200
200
Derating Curve
Mechanical Dimensions
Max. Capacitive Load
Output Voltage
3.3
5
9
12
820 µF
660 µF
470 µF
330 µF
±5
±9
±12
±15
±330 µF ±220 µF ±150 µF ±120 µF
15
220 µF
Pin Connections
Pin Single
Dual
1
-Vin
-Vin
2
+Vin
+Vin
3
Remote ON/OFF
6 +Vout
+Vout
NC = No Connection
Pin
7
8
9
Single
NC
NC
-Vout
Dual
Common
NC
-Vout
MicroPower Direct
Mechanical Notes:
Mechanic
• All dime
dimensions are typical in inches (mm)
• Toleranc
Tolerance x.xx = ±0.01 (±0.25)
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]