PWM-120 series

PWM-120
120W PWM output LED power supply
F
110
■ Features
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
Constant voltage PWM style output
Dimming range : 0~100%
High efficiency up to 90.5%
Protections: Short circuit / Over load / Over voltage
M
M
SELV
IP67
series
05
■ Applications
LED strip lighting
Indoor LED lighting
LED decorative lighting
Architecture lighting
/ Over temperature
Class Ⅱ power unit, no FG
Built-in 3 in 1 dimming function
(0~10Vdc or PWM signal or resistance)
Suitable for dry / damp / wet locations
No load power consumption<0.5W
5 years warranty
■ Description
PWM-120 is one 120W waterproof constant-voltage output LED power supply series. Differentiating from
general DC output power supplies, PWM-120 transmits PWM style output, adapting to directly driving all
kinds of LED strips that the color temperature can be maintained and the brightness homogeneity can be
assured. Adopting a universal input range between 90VAC and 305VAC and incorporating the built-in
PFC function, this series is also designed with a 3 in 1 dimming function (0~10Vdc, PWM signal or resistance)
that simplifies the brightness adjustment for system designers so as to achieve light reduction and energy
conservation.
Providing a high efficiency up to 90.5% and a low no load power consumption below 0.5W, PWM-120 can
satisfy the energy saving demand for the new generation LED lighting. The class Ⅱ design (without FG pin)
and the double insulation weather-resistant cable (SJTW) on the input side make it convenient for users
to flexibly install on various types of lighting systems. The enclosure design is a 94V-0 flame retardant
plastic case. The interior is fully potted with silicone that enhances the heat dissipation and allows PWM-120
to meet the anti-vibration demand up to 5G; it also thus conforms to IP67 level, enabling PWM-120 to be
used in a highly dusty and highly humid harsh environment. The entire series can operate under the
temperature between -40~+70℃ and comply with the relevant global lighting safety certification.
■ Model Encoding
PWM - 120 - 12
Output voltage
Output wattage
Series name
File Name:PWM-120-SPEC 2015-06-02
PWM-120
120W PWM output LED power supply
series
SPECIFICATION
MODEL
OUTPUT
PWM-120-12
PWM-120-24
PWM-120-36
PWM-120-48
DC VOLTAGE
12V
24V
36V
48V
RATED CURRENT
10A
5A
3.4A
2.5A
RATED POWER
120W
120W
122.4W
120W
DIMMING RANGE
0 ~ 100%
PWM FREQUENCY (Typ.)
300Hz
VOLTAGE TOLERANCE
±4.0%
±4.0%
±2.0%
±1.0%
SETUP, RISE TIME Note.2 500ms, 80ms 230VAC / 115VAC at full load
HOLD UP TIME (Typ.)
16ms/230VAC
VOLTAGE RANGE
90 ~ 305VAC
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
16ms/115VAC at full load
127 ~ 431VDC
TOTAL HARMONIC DISTORTION THD< 20% when output loading≧60% at 115VAC/230VAC input and output loading≧75% at 277VAC input
INPUT
EFFICIENCY (Typ.)
88%
AC CURRENT (Typ.)
1.3A / 115VAC
90%
INRUSH CURRENT (Typ.)
COLD START 60A(twidth=520μs measured at 50% Ipeak) at 230VAC
0.65A / 230VAC
90%
90.5%
0.55A / 277VAC
MAX. NO. of PSUs on 16A 4 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
CIRCUIT BREAKER
LEAKAGE CURRENT
OVERLOAD
SHORT CIRCUIT
<0.25mA / 277VAC
108 ~ 120% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Hiccup mode, recovers automatically after fault condition is removed
15 ~ 17V
PROTECTION
OVER VOLTAGE
28 ~ 34V
41 ~ 46V
54 ~ 60V
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE
Shut down o/p voltage, re-power on to recover
WORKING TEMP.
-40 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 95% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT
±0.03%/℃ (0 ~ 50℃)
VIBRATION
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY STANDARDS
UL8750, CSA C22.2 No. 250. 13-12 , ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP67 approved; Design refer to EN60335-1
WITHSTAND VOLTAGE
I/P-O/P:3.75KVAC
SAFETY &
ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH
EMC
EMC EMISSION
Compliance to EN55015, EN61000-3-2 Class C (≧60% load) ; EN61000-3-3
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge L-N : 2KV), criteria A
MTBF
228.7K hrs min.
OTHERS DIMENSION
PACKING
NOTE
MIL-HDBK-217F (25℃)
191*63*37.5mm (L*W*H)
0.97Kg; 15pcs/15.6Kg/0.87CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
File Name:PWM-120-SPEC 2015-06-02
PWM-120
120W PWM output LED power supply
series
Block Diagram
PFC fosc : 50~120KHz
PWM fosc : 60~130KHz
EMI FILTER
&
RECTIFIERS
I/P
+V
RECTIFIERS
&
FILTER
POWER
SWITCHING
PFC
CIRCUIT
DIMMING
CIRCUIT
-V
O.L.P.
O.T.P.
O.L.P.
DIM+
DIM-
DETECTION
CIRCUIT
PWM & PFC
CONTROL
O.V.P.
Derating Curve
Static Characteristics
100
100
90
80
80
230VAC
Input only
70
12V only
50
LOAD (%)
LOAD (%)
60
40
20
-40
-25
0
15
30
40 45 50
60
70 (HORIZONTAL)
60
50
40
90
100
AMBIENT TEMPERATURE (℃)
125
135
145
155 165
175
180
200
230
305
INPUT VOLTAGE (V) 60Hz
Power Factor Characteristic
PF
Constant Voltage Mode
1 .0 0
0 .9 5
0 .9 0
0 .8 5
0 .8 0
0 .7 5
0 .7 0
0 .6 5
0 .6 0
0 .5 5
0 .5 0
0 .4 5
0 .4 0
0 .3 5
0 .3 0
277V
230V
115V
10%
20%
30%
40%
50%
60%
LOAD
70%
80%
90% 100%
(120W)
File Name:PWM-120-SPEC 2015-06-02
PWM-120
120W PWM output LED power supply
series
EFFICIENCY vs LOAD (48V Model)
EFFICIENCY (%)
PWM-120 series possess superior working efficiency that up to 90.5% can be reached in field applications.
92
91
90
89
88
87
86
85
84
83
82
81
80
277V
230V
115V
10%
20%
30%
40%
50%
60%
70%
80%
90% 100%
LOAD
DIMMING OPERATION
The PWM style output is a simple switching of supply ON/OFF at a rate so fast that the human eye cannot see LED
flickering. Duty cycle describes the proportion of time when output voltage is ON relative to the entire period of time.
It is expressed in percentage, 100% being fully ON (maximal brightness) and a low duty cycle corresponding to lower
brightness. With built-in 3 in 1 dimming function, the duty of the PWM style output can be adjusted through output cable
by connecting a resistance or 0~10Vdc or 10V PWM signal between DIM+ and DIM-.
◎Connection
LED Strips
+V
-V
DIM+
+
+
-
+
0~10Vdc or 10V PWM or resistance control dimmer
DIM-
-
※DO NOT connect "DIM- to -V"
File Name:PWM-120-SPEC 2015-06-02
PWM-120
120W PWM output LED power supply
series
◎Duty cycle of output current VS Dimming input
100% when DIM+/DIM- are open circuit.
100%
90%
Duty cycle of output current
80%
Note
70%
※ Note : The output current drops down to 0% when the dimming input is about
6 KΩor 0.6Vdc, or 10V PWM signal with 6% duty cycle.
Non-Linear
60%
50%
40%
30%
20%
10%
0%
0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V
0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
Short 10K 20K 30K 40K 50K 60K 70K 80K 90K 100K
Dimming input
0~10V
Duty cycle of 10V PWM (frequency range = 100~3KHz)
Short~100KΩresistance
◎PWM Style Output
Output DC current
ON
Duty cycle(%) =
T ON
T
Output PWM frequency : 300Hz fixed (Typ.)
OFF
Io=0A
×100%
T ON
T
Mechanical Specification
Case No. PWM-120
Unit:mm
191
5
5
300±20
50±3
300±20
50±3
+V(Red)
-V(Black)
95.5
63
AC/L(Brown)
AC/N(Blue)
31.5
SJTW 18AWG×2C
SJTW 14AWG×2C
5
UL2464 18AWG×2C
2 -ψ
4.5
※ T case: Max. Case Temperature.
37.5
5
DIM+(Blue)
DIM-(White)
Recommend Mounting Direction
File Name:PWM-120-SPEC 2015-06-02
PWM-120
120W PWM output LED power supply
series
Installation Manual
◎Connection
+V(RED)
AC/L(BROWN)
AC/N(BLUE)
-V(BLACK)
+
-
LED Strip
DIM+(BLUE)
+
DIM-(WHITE)
0~10Vdc or 10V PWM
or resistance Dimmer
◎Cautions
Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure
that it cannot be re-connected inadvertently!
Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when
the adjacent device is a heat source.
Mounting orientations other than standard orientation or operate under high ambient temperature may increase the
internal component temperature and will require a de-rating in output current.
Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer
to its specification.
For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is
tight so that water cannot intrude into the system.
For dimmable LED power supplies, make sure that your dimming controller is capable of driving these units.PWM series
require 0.15mA each unit.
Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.
DO NOT connect "DIM+ to -V".
Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30
minutes.
The power supply is considered as a component that will be operated in combination with final equipment. Since EMC
performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC
Directive on the complete installation again.
For more information about installation, please refer to www.meanwell.com/webnet/search/installationsearch.html
for details.
File Name:PWM-120-SPEC 2015-06-02