Thick Film Chip Attenuators NFA Series FEATURES • HIGH FREQUENCY (UP TO 3GHz) PERFORMANCE • SMALL 0404 SPACE SAVING SMT PACKAGE • LOWER PLACEMENT COST (SINGLE COMPONENT RATHER THAN THREE DECRETE RESISTORS) • BOTH FLOW AND REFLOW SOLDERING APPLICABLE RoHS Compliant includes all homogeneous materials *See Part Number System for Details SPECIFICATIONS Part Number NFA0404E0R0TR NFA0404E0R5TR NFA0404E1R0TR NFA0404E1R5TR NFA0404E2R0TR NFA0404E3R0TR NFA0404E4R0TR NFA0404E5R0TR NFA0404E6R0TR NFA0404E7R0TR NFA0404E8R0TR NFA0404E9R0TR NFA0404E100TR NFA0404E110TR NFA0404E120TR NFA0404E130TR NFA0404E140TR NFA0404E150TR NFA0404E160TR NFA0404E170TR NFA0404E180TR NFA0404E190TR NFA0404E200TR Power Rating (Package) Temperature Range Impedance Characteristic Voltage Standing Wave Ratio Frequency Range Attenuation Value DC ~ 3.0GHz 0.0dB 0.5dB 1.0dB 1.5dB 2.0dB 3.0dB 4.0dB 5.0dB 6.0dB 7.0dB 8.0dB 9.0dB 10dB 11db 12dB 13dB 14dB 15dB 16dB 17dB 18dB 19dB 20dB 1.1 max. 0.1W Description Insulation Resistance Resistance to Soldering Heat (260°C for 5 sec.) Temperature Cycling (5 cycles -55°C ~ +125°C) Endurance at +85°C (after 1,000 hrs) -40°C ~ +125°C 50Ω 1.2 max. 05 ~ 2dB ± 0.1dB Performance 3dB ~ 5dB 6dB ~ 20dB 100Meg ohms minimum ± 0.2dB ± 0.3dB Attentuation Value ± 0.1dB ±0.3dB ±0.4dB ±0.8dB ±1.0db ±1.5dB ±2.0dB ±2.5dB PART NUMBER SYSTEM NFA 0404 E 3R0 TR F RoHS compliant Tape & Reel Attenuation Impedance Characteristic Case Size Series ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 1 Thick Film Chip Attenuators NFA Series DIMENSIONS (mm) L W P t a 1.0 ± 0.10 1.0 ± 0.10 0.65 0.35 ± 0.05 0.33 ± 0.05 Terminal #1 P CIRCUIT DIAGRAM A W a t L Terminal: 100% Sn finish over Ni Barrier Body: Alumina Element: Thick Film (RuO2) LAND PATTERN DIMENSIONS (mm) A B F P1 0.5 0.45 1.5 0.65 P1 A ATTENUATION CODE X 0.5dB 1 1.0dB Y 1.5dB 2 2dB 3 3dB 4 4dB 5 5dB 6 6dB 7 7dB 8 8dB A 10dB B 11dB C 12dB E 14dB F 15dB G 16dB H 17dB J 18dB K 19dB L 20dB F B ® 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thick Film Chip Resistors NRC Series FEATURES • EIA STANDARD SIZING 0201(1/20W), 0402(1/16W), 0603(1/10W), 0805(1/8W), 1206(1/4W), 1210(1/3W), 2010(3/4W) AND 2512(1W) • METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE ..(CERMET) PROVIDES UNIFORM QUALITY AND HIGH RELIABILITY • DOUBLE GLASS OVERCOAT ASSURES STRONG MECHANICAL ..CONTRUCTION RoHS AND LONG LIFE, NICKEL BARRIER PREVENTS LEACHING Compliant • BOTH FLOW SOLDER AND REFLOW SOLDERING ARE APPLICABLE includes all homogeneous materials • ZERO OHM (JUMPER) CHIP AND TRIMMABLE TYPE ARE AVAILABLE *4 *See Part Number System for Details Type EIA Size NRC02 0201 NRC04 0402 NRC06 0603 NRC10 0805 NRC12 1206 NRC25 1210 NRC50 2010 NRC100 2512 NRC02ZO NRC04ZO NRC06ZO NRC10ZO NRC12ZO NRC25ZO NRC50ZO NRC100ZO 0201 0402 0603 0805 1206 1210 2010 2512 Max.*1 Max.*2 Resistance Temperature Resistance Operating Resistance Working Overload Tolerance Coefficient Range Temperature Value Voltage Voltage (Code) (ppm/°C) (Ω) Range (°C) ±1% (F) ±250 10 ~ 1M E-24 1/20 (0.05) W 25V 50V ±5% (J) E-24 -55 ~ +125 ±200 10 ~ 10M ±10% (K) E-12 ±1% (F) +500/-200 1.0 ~ 9.96 E-96 ±1% (F) ±100 10 ~ 1M E-96 1/16 (0.063) W 50V 100V ±1% (F) ±300 1.02M ~ 10M E-96 -55 ~ +155 ±5% (J) ±200 10 ~ 1M E-24 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±400 1.0 ~ 9.96 E-96 ±1% (F) ±100 33.2 ~ 1M E-96 1/10 (0.10) W 50V 100V ±1% (F) ±200 10 ~ 32.4 & 1.1M ~ 10M *3 E-96 -55 ~ +155 ±5% (J) ±200 10 ~ 1M E-24 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±400 1.0 ~ 9.96 E-96 ±1% (F) ±100 33.2 ~ 1M E-96 1/8 (0.125) W 150V 300V ±1% (F) ±200 10 ~ 32.4 & 1.1M ~ 10M *3 E-96 ±5% (J) ±200 10 ~ 1M E-24 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±400 1.0 ~ 9.96 E-96 ±1% (F) ±100 33.2 ~ 1M E-96 1/4 (0.250) W 200V 400V ±1% (F) ±200 10 ~ 32.4 & 1.1M ~ 10M *3 E-96 ±5% (J) ±200 10 ~ 1M E-24 -55 ~ +175 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±100 E-96 10 ~ 1M 1/3 (0.33) W 200V 400V ±5% (J) ±200 E-24 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±100 E-96 10 ~ 1M 3/4 (0.75) W 200V 400V ±250 E-24 ±5% (J) ±350 1.0 ~ 9.1 & 1.1M ~ 10M *3 E-24 ±1% (F) ±100 E-96 10 ~ 1M 1W 250V 500V ±250 ±5% (J) E-24 ±350 1.0 ~ 9.1 *3 Rated Current 0.5A (0.05Ω max. DC Resistance -55 ~ +125 Rated Current 1.0A (0.05Ω max. DC Resistance Rated Current 1.0A (0.05Ω max. DC Resistance -55 ~ +150 Rated Current 2.0A (0.05Ω max. DC Resistance Zero Ohm Jumper Rated Current 2.0A (0.05Ω max. DC Resistance Rated Current 2.0A (0.05Ω max. DC Resistance -55 ~ +175 Rated Current 2.0A (0.05Ω max. DC Resistance Rated Current 2.0A (0.05Ω max. DC Resistance Power Rating at 70°C ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 3 Thick Film Chip Resistors NRC Series Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: Note *1 - Maximum allowable continuous Working Voltage for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above (or) 100 80 Note *2 - Maximum allowable Overload voltage is two times the Maximum Working Voltage (see Note *1 above). Note *3 - Made to order. Contact NIC for leadtime. Note *4 - Please contact NIC for availability of laser trimmable versions of 0805 and 1206 sizes parts. Note *5 - Please note, NIC’s NRC series products are capable of meeting the following specifications: JIS-C 5202, EIAJ RC-2690, EIA575, EIA PDP-100, MIL-R-5542D and UL94V-0. RATE (%) Power rating (Watts) x Resistance (Ohms) 60 40 20 0 -20 20 60 100 0805/1206/1210/2010/2512 0402/0603 0201 140 180 125 150 175 oC DIMENSIONS (mm) Type NRC02 NRC04 NRC06 NRC10 NRC12 NRC25 NRC50 NRC100 NRCO2ZO NRCO4ZO NRCO6ZO NRC10ZO NRC12ZO NRC25ZO NRC50ZO NRC100ZO Power Rating 1/20W 1/16W 1/10W 1/8W 1/4W 1/3W 3/4W 1W JUMPER JUMPER JUMPER JUMPER JUMPER JUMPER JUMPER JUMPER EIA L Size 0201 0.6 ± 0.03 0402 1.0 +0.1/-0.05 0603 1.6 ± 0.15 0805 2.0 ± 0.20 1206 3.1 ± 0.15 1210 3.1 ± 0.15 2010 5.0 ± 0.15 2512 6.4 ± 0.15 0201 0402 0603 0805 1206 1210 2010 2512 W H T 0.3 ± 0.03 0.25 ± 0.05 0.1 ± 0.05 0.5 +0.1/-0.05 0.3 ± 0.05 0.2 ± 0.1 0.8 ± 0.15 0.45 ± 0.1 0.3 ± 0.15 1.25 ± 0.10 0.5 ± 0.10 0.35 ± 0.20 1.55 ± 0.15 0.55 ± 0.10 0.45 ± 0.20 2.50 ± 0.20 0.55 ± 0.10 0.50 ± 0.20 2.50 ± 0.15 0.55 ± 0.10 1.00 ± 0.20 3.20 ± 0.15 0.55 ± 0.10 1.30 ± 0.20 Same as NRC02 Same as NRC04 Same as NRC06 Same as NRC10 Same as NRC12 Same as NRC25 Same as NRC50 Same as NRC100 NRC02 ~ NRC12 t 0.15 ± 0.05 0.25 ± 0.1 0.3 ± 0.15 0.35 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.60 ± 0.30 CONSTRUCTION NRC25 ~ NRC100 PART NUMBER SYSTEM (E-24 VALUES) NRC12 J 103 TR 10 F RoHS compliant Optional 10,000 piece reel Tape & Reel Packaging Resistance Code: First 2 figures are significant, 3rd digit is the multiplier, “R” indicates a decimal point. Tolerance Code: J=5% (Std) Series and Size Examples of Resistance Code: 4R7 = 4.7 ohms 100 = 10 ohms 101 = 100 ohms 102 = 1K ohms 103 = 10K ohms 104 = 100K ohms 105 = 1 meg ohms 106 = 10meg ohms ® 4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thick Film Chip Resistors PART NUMBER SYSTEM (E-96 VALUES) NRC10 F 1003 TR 10 F NRC Series Examples of Resistance Code: 10R0 = 10 ohms 47R5 = 47.5 ohms 1000 = 100 ohms 1001 = 1K ohms 1002 = 10K ohms 1003 = 100K ohms RoHS compliant Optional 10,000 piece reel Tape & Reel Packaging Resistance Code: First 3 figures are significant, 4th digit is the multiplier, “R” indicates a decimal point. Tolerance Code: F=1% (Std) Series and Size 1004 = 1meg ohms 1050 = 105 ohms 1501 = 1.5K ohms 1052 = 10.5K ohms 1153 = 115K ohms 1214 = 1.21meg ohms Marking (No marking on 0201 and 0402 size). 1. For E-12 & E-24 Series (±5%-J, (STD) Tolerance In 0603, 0805, 1206, 1210, 2010 and 2512 sizes: 3 DIGIT SYSTEM - First two digits are significant and third digit is multiplier, “R” indicates decimal on values under 10 ohms. Examples: R10 = .10 ohms 1R0 = 1.0 ohms 103 = 10k ohms 101 = 100 ohms 102 = 1k ohms 104 = 100k ohms 470 = 47 ohms 105 = 1 megohms 2. For E-96 Series (±1%-F Tolerance) in 0805, 1206 and 1210 sizes: 4 DIGIT SYSTEM - First 3 digits are significant and fourth digit is multiplier, “R” indicates decimal on values under 100 ohms. Examples: 0R10 = .10 ohms 1R00 = 1.0 ohms 10R0 = 10 ohms 1003 = 100 kohms 1000 = 100 ohms 1004 = 1 megohms 1001 = 1k ohms 1052 = 10.5k ohms 1002 = 10k ohms 2213 = 221k ohms 3. For E-96 Series (±1% -F Tolerance) in 0603 size 3 DIGIT SYSTEM (Due to space restrictions) STANDARD E-12, E-24, E-96 VALUES AND 0603 RESISTANCE CODES E-12 Value 10 12 15 18 22 27 33 39 47 56 68 82 91 E-24 Value 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 E-96 Value Code 100 01 110 05 121 09 133 13 147 17 162 21 178 25 196 29 215 33 237 37 261 41 287 45 316 49 348 53 383 57 422 61 464 65 511 69 562 73 619 77 681 81 750 85 825 89 909 93 Value Code 102 02 113 06 124 10 137 14 150 18 165 22 182 26 200 30 221 34 243 38 267 42 294 46 324 50 357 54 392 58 432 62 475 66 523 70 576 74 634 78 698 82 768 86 845 90 931 94 Value Code 105 03 115 07 127 11 140 15 154 19 169 23 187 27 205 31 226 35 249 39 274 43 301 47 332 51 365 55 402 59 442 63 487 67 536 71 590 75 649 79 715 83 787 87 866 91 953 95 Value Code 107 04 118 08 130 12 143 16 158 20 174 24 191 28 210 32 232 36 255 40 280 44 309 48 340 52 374 56 412 60 453 64 499 68 549 72 604 76 665 80 732 84 806 88 887 92 976 96 MULTIPLIER CODE Code A B,b C D,d E F G H X Y Z Multiplier 100 101 102 103 104 105 106 107 10-1 10-2 10-3 CODING FORMULA XX ® X Multiplier Code Example: 10.2kΩ = 102 x 102 Ω = 02C 02 C 33.2 Ω = 332 x 10-1 = 51X 51 X MARKING EXAMPLES 10Ω = 01X 7.5k Ω = 85B or 85b 150k Ω = 18D or 18d 1 MegΩ = 01E Resistance Code NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 5 Thick Film Chip Resistors NRC Series TAPING SPECIFICATIONS (1) Availability Type NRC02 NRC04 NRC06 NRC10 NRC12 NRC25 NRC04Z0 NRC06Z0 NRC10Z0 NRC12Z0 NRC25Z0 Power Rating 1/20W 1/16W 1/10W 1/8W 1/4W 1/3W Jumper Jumper Jumper Jumper Jumper EIA Size 0201 0402 0603 0805 1206 1210 0402 0603 0805 1206 1210 Carrier Tape Material Paper Paper Paper Paper Paper Plastic Paper Paper Paper Paper Plastic Fig. A A A A A B A A A A B Width (mm) 8 8 8 8 8 12 8 8 8 8 12 Qty per 10" Reel N/A N/A 10,000 10,000 10.000 N/A N/A 10,000 10,000 10.000 N/A Qty per 7" Reel 10,000 10,000 5,000 5,000 5,000 4,000 10,000 5,000 5,000 5,000 4,000 (2) PAPER TAPE DIMENSIONS (mm) FIG. A Type NRC02* NRC04* NRC06* NRC10* NRC12* EIA Size 0201 0402 0603 0805 1206 A 0.41 ±0.1 0.65 0.1 1.135 ± 0.05 1.65 ±0.2 2.0 ±0.2 B 0.71 ±0.1 1.15 ±0.1 1.95 ± 0.05 2.4 ±0.2 3.6 ±0.2 D E 1.5 + 0.1 F Po P1 2.0 ± 0.1 2.0 ± 0.05 P2 N/A P3 2.0 ± 0.1 2.0 ± 0.05 1.75 ± 0.1 3.5 ± 0.05 4.0 ± 0.1 W 8.0 ± 0.2 N/A 4.0 ± 0.05 4.0 ± 0.05 * Same for JUMPER (Z0) types. 1.0 Max. (0201 Size 0.5 Max.) P0 P3 D E Cover tape F W B A 1.1 Max. (0201 Size 1.0 Max.) P1 P2 ® 6 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thick Film Chip Resistors NRC Series (3) EMBOSSED PLASTIC TAPE SPECIFICATION FIG. B. Type EIA Size A B D E F P0 P1 W NRC25* NRC50* NRC100* 1210 2010 2512 2.9 ± 0.2 2.9 ± 0.1 3.6 ± 0.1 3.6 ± 0.2 5.4 ± 0.1 6.9 ± 0.1 1.5 ± 0.1 1.5 ± 0.1 5.65 ± 0.05 3.0 ± 0.1 4.0 ± 0.05 12.0 ± 0.1 0.2 ±0.05 P0 D E Cover tape F W B A 1.1 Max. P1 (4) REELSPECIFICATIONS FIG. C. 2 ± .0 0. 5 178∅ or 254∅ ±2 21 0. 8 80∅ or 100∅ ±2 ± 13∅ ±0.5 2.0 ± 0.5 1. Leader tape : Approximately 250 m/m (160mm for 0201 case size)leader shall be provided at each end of the tape. 2. Accumulative tolerance of feeding hole and chip pocket shall not exceed 0.2mm over 10 pitches. Type EIA Size L ± 1.5 NRC02* NRC04* NRC06* NRC10* NRC12* NRC25 NRC50 NRC100* 0201 0402 0603 0805 1206 1210 2010 2512 10.0 10.0 10.0 10.0 10.0 10.0 13.5 13.5 * Same for JUMPER (Z0) types. 10 + 1.5 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 7 Thick Film Chip Resistors NRCE Series FEATURES • EXTENDED VALUE RANGE (47MΩ ~ 4.7GΩ) & PRECISION TOLERANCES • EIA STANDARD SIZING 0603, 0805 and 1206 • METAL GLAZED THICK FILM ON HIGH PURITY ALUMINA SUBSTRATE ..(CERMET) ...PROVIDES UNIFORM QUALITY AND HIGH RELIABILITY • DOUBLE GLASS OVERCOAT ASSURES STRONG MECHANICAL ..CONTRUCTION AND RoHS ...LONG LIFE, NICKEL BARRIER PREVENTS LEACHING Compliant • ALL SIZES ARE AVAILABLE IN TAPE/REEL FOR AUTOMATIC MOUNTING includes all homogeneous materials • BOTH FLOW SOLDER AND REFLOW SOLDERING ARE APPLICABLE *See Part Number System for Details SPECIFICATIONS Type EIA Size Power Rating at 70°C Max. *1 Working Voltage Max. *2 Overload Voltage Resistance Tolerance Code Temperature Coefficient (ppm/°C) Resistance Range (Ω) NRCE06 0603 1/16 (0.063) W 50V 100V ±10%(K), ±20%(M) ±500 47MΩ ~ 1GΩ NRCE10 0805 1/10 (0.10) W 150V 300V ±10%(K), ±20%(M) NRCE12 1206 1/8 (0.125) W 200V 400V ±10%(K), ±20%(M) ±500 ±1500 ±500 ±1500 47MΩ ~ 1GΩ 1.2GΩ ~ 4.7GΩ 47MΩ ~ 1GΩ 1.2GΩ ~ 4.7GΩ Resistance Value Operating Temperature Range E-12 -55°C ~ +125°C Note *1 - Maximum allowable continuous Working Voltage for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above (or) Power rating (Watts) x Resistance (Ohms) Note *2 - Maximum allowable Overload voltage is two times the Maximum Working Voltage (see Note *1 above). Please note, NIC’s NRCE series products are capable of meeting the following specifications: JIS-C 5202, EIAJ RC-2690, EIA575, EIA PDP-100, MIL-R-5542D and UL94V-0. PART NUMBER SYSTEM (E-24 VALUES) NRCE12 K 476 TR F 10 Optional 10,000 Piece Reel RoHS compliant Tape & Reel Packaging Resistance Code: First 2 figures are significant, 3rd digit is the multiplier, “R” indicates a decimal point. Tolerance Code: M=20%, K=10% Series and Size Power Derating Curve: For operation above 70oC, power rating must be derated according to the following chart: 100 RATE (%) 80 60 40 20 0 -20 20 100 60 70 CONSTRUCTION 125 oC *Note: Lead Free terminations also available. See part numbering system (page 2) for ordering instructions ® 8 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thick Film Chip Resistors NRCE Series DIMENSIONS (mm) Type EIA Size L W H T t NRCE06 0603 1.60 ± 0.15 0.80 ± 0.15 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 NRCE10 0805 2.00 ± 0.20 1.25 ± 0.10 0.50 ± 0.10 0.40 ± 0.20 0.40 ± 0.20 NRCE12 1206 3.10 ± 0.15 1.55 ± 0.15 0.55 ± 0.10 0.50 ± 0.25 0.50 ± 0.30 Note: For details on construction see the NRC Series data sheet Marking E-12 Series: Tolerances are ±20% (M), ±10% (K) 3 DIGIT SYSTEM - First 2 digits are significant and 3rd digit is multiplier. Examples: 686 =68Meg ohms, 827 = 820Meg ohms, 108 = 1Gig ohms STANDARD E-12 VALUES E-12 Value 10 12 15 18 22 27 33 39 47 56 68 82 91 See NRC Series for tape and reel specification ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 9 Anti-Surge Thick Film Chip Resistors NRCP Series RoHS Compliant FEATURES includes all homogeneous materials • EXCELLENT ANTI-SURGE CHARACTERISTICS • BOTH FLOW SOLDER AND REFLOW SOLDERING ARE APPLICABLE Type EIA Size NRCP06 NRCP10 NRCP12 0603 0805 1206 NRCP25 1210 NRCP35 1812 NRCP50 2010 NRCP100 2512 *See Part Number System for Details Power Max. *1 Max. *2 Resistance Temperature Resistance Operating Resistance Rating Working Overload Tolerance Coefficient Range Temperature Value at 70°C Voltage Voltage Code (ppm/°C) (Ω) Range 1/10W 50 100 10% (K), 20% (M) 10 ~ 1Meg 1/8W 150 300 10 ~ 1Meg 1/4W 10 ~ 1Meg 1/3W 1.1K ~ 1Meg -55°C ~ ±200ppm E-24 5% (J), 10% (K), +155°C 1/2W 10 ~ 1K 20% (M) 200 400 1/2W 10 ~ 1Meg 3/4W 10 ~ 1Meg 1W 10 ~ 1Meg Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: Note *1 - Maximum allowable continuous Working Voltage for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above (or) 100 DERATING (%) Power rating (Watts) x Resistance (Ohms) Note *2 - Maximum allowable Overload Voltage is 2 times the Maximum Working Voltage (see Note *1 above) or Maximum Overload Voltage as specified in the table whichever is lower. 80 60 40 20 PART NUMBER SYSTEM NRCP 12 K 226 TR F 0 -60 -40 -20 0 20 40 60 80 100 120 140 70 155 oC RoHS compliant Tape & Reel Packaging Resistance Code: First 2 figures are significant, 3rd digit is the multiplier, “R” indicates a decimal point. Tolerance Code: M=20%, K=10%, J=5% Case size code Series COMPONENT AND LAND PATTERN DIMENSIONS (mm) Type NRCP06 NRCP10 NRCP12 NRCP25 NRCP35 NRCP50 NRCP100 EIA Size 0603 0805 1206 1210 1812 2010 2512 L 1.60 ± 0.15 2.00 ± 0.10 3.20 ± 0.15 3.20 ± 0.15 4.50 ± 0.20 5.00 ± 0.15 6.30 ± 0.15 W 0.80 ± 0.15 1.25 ± 0.10 1.60 ± 0.15 2.50 ± 0.15 3.20 ± 0.20 2.50 ± 0.15 3.20 ± 0.15 H 0.45 ± 0.10 0.50 ± 0.10 0.60 ± 0.10 0.60 ± 0.10 0.60 ± 0.10 0.60 ± 0.10 0.60 ± 0.10 P 0.30 ± 0.20 0.40 ± 0.20 0.50 ± 0.20 0.50 ± 0.20 0.50 ± 0.20 0.50 ± 0.30 0.70 ± 0.20 L Resistive element (RuO2 Film) 103 W Protective Overcoat Side termination (Ni Barrier) Termination finish (100% Sn) Al203(96%) Substrate Base termination (Ag/Pd) H ® 10 P NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Anti-Surge Thick Film Chip Resistors NRCP Series PERFORMANCE CHARACTERISTICS Test Items Voltage proof Variation of resistance with temperature Requirement ΔR± ([ ] +0.1Ω) No breakdown or flashover Test Methods (JISC5201-1) Maximum Overload Voltage, 60 seconds +20°C/-55°C/+20°C/+125°C/+20°C or +20°C/-55°C/+20°C/+155°C/+20°C Rated Voltage x 2.5 or Max. Overload Voltage x 2 Whichever is the greater, 2 seconds Immersion into solder bath at 260°C for 5 seconds 100 times at -55°C 30 minutes/+125°C 30 minutes +60°C, 90% ~ 95% RH, 1,000 hours Rated Voltage, 1.5 hrs ON/0.5 hrs OFF Cycle, +70°C, 1,000 hrs +60°C, 90% ~ 95% RH, 1,000 hours, Rated Voltage, 1.5 hrs On/0.5 hrs OFF cycle, 1,000 hrs See Specifications Table Shortime Overload [2%] Resistance to Soldering Heat Temperature Cycling Humidity Test (Steady State) Load Life [1%] [1%] [1%] [3%] Humidity Load Life [3%] ONE-PULSE LIMITING POWER NRCP100 NRCP50 NRCP25 NRCP12 NRCP10 NRCP06 REFLOW SOLDERING TEMPERATURE PROFILE LAND PATTERN DIMENSIONS (mm) 300 Peak Temperature 260°C 10 sec. max. 260 220 200 150 140 ~ 180°C 120 ~ 160 Sec. 100 Time above 220°C 20 sec. max. a 0.9 1.35 2.2 2.2 3.5 3.7 4.7 b 2.6 3.45 4.7 5.2 6.1 6.2 7.6 c 0.78 1.1 1.4 2.15 2.75 2.15 2.75 b 50 c 0 Note: Maximum of 3 times a ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 11 Anti-Surge Thick Film Chip Resistors NRCP Series PAPER CARRIER TAPE DIMENSIONS (mm) Type A B NRCP06 1.10 ±0.20 1.90 ± 0.20 NRCP10 1.65 ± 0.20 2.40 ± 0.20 NRCP12 2.00 ± 0.20 NRCP25 2.85 ± 0.10 W F E P1 P2 P0 φD T 8.00 ±0.20 3.50 ±0.05 1.75 ±0.10 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 1.50 ±0.10 1.40 max. 3.50 ± 0.20 B W F E ∅ Do Component P2 P1 A Forward Direction P0 T EMBOSSED PLASTIC CARRIER DIMENSIONS (mm) Type A B NRCP35 3.50 ± 0.10 4.80 ± 0.10 NRCP50 2.90 ±0.10 5.40 ±0.10 NRCP100 3.40 ±0.10 6.60 ±0.10 W F E P1 P2 P0 φDo T 12.00 ±0.20 5.50 ±0.05 1.75 ±0.10 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 1.50 ±0.10 1.10 max. E T P0 B W F D0 A P K REEL DIMENIONS (mm) AND QUANTITY Type A B C W Quantity C NRCP06 NRCP10 NRCP12 NRCP25 NRCP35 5,000 180 +0.0 -3.0 60 +1.0 -0.0 NRCP50 NRCP100 13 ±0.20 9.0 ±0.50 B 4,000 3.2 ±1.50 W A ® 12 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Anti-Sulfur Thick Film Chip Resistors NRCS Series FEATURES • • • • • RoHS GOLD INNER ELECTRODE FOR SUPERIOR ANTI-CORROSION PROPERTIES EIA STANDARD SIZING 0402, 0603, 0805, 1206, 1210, 2010 AND 2512 Compliant includes all homogeneous materials SUIT FOR HIGH RELIABILITY APPLICATIONS IN HARSH ENVIRONMENTS ALL SIZES ARE AVAILABLE IN TAPE/REEL FOR AUTOMATIC MOUNTING *See Part Number System for Details SAC REFLOW SOLDERABLE (THREE TIMES AT 260°C FOR 10 SECONDS) SPECIFICATIONS EIA Power Rating Size at 70°C Type NRCS04 0402 Max. *1 Working Voltage NRCS10 0603 0805 0.063W 100V 0.10W 0.125W Resistance Tolerance Code Temperature Coefficient (ppm/°C) ±200 ±1%(F), ±2%(G), ±5%(J) 50V NRCS06 Max. *2 Overload Voltage 150V 300V ±350 0 ~ +600 ±100 ±200 ±1%(F) ±2%(G), ±5%(J) ±1%(F), ±2%(G), ±5%(J) ±1%(F) ±2%(G), ±5%(J) ±350 ±100 ±200 ±250 ±1%(F), ±2%(G), ±5%(J) ±350 ±1%(F) ±2%(G), ±5%(J) NRCS12 NRCS25 1206 1210 0.25W 0.25W 2010 0.50W NRCS100 2512 1.0W ±250 ±1%(F), ±2%(G), ±5%(J) 200V NRCS50 ±100 ±200 400V ±1%(F) 2%(G), 5%(J) ±1%(F), ±2%(G), ±5%(J) ±1%(F) ±2%(G), ±5%(J) ±1%(F), ±2%(G), ±5%(J) ±1%(F) ±2%(G), ±5%(J) ±1%(F), ±2%(G), ±5%(J) Note *1 - Maximum allowable continuous Working Voltage for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above or the result of the following formula ±350 ±100 ±200 ±250 ±350 ±100 ±200 ±250 ±350 ±100 ±200 ±250 ±350 "Maximum Overload Voltage" as specified above or 2x the result of the following formula 10 ~ 1M 3.9 ~ 9.1 1.1M ~ 22M 1.0 ~ 3.6 10 ~ 1M 10 ~ 1M 1.0 ~ 9.1 1.1M ~ 22M 10 ~ 1M 10 ~ 1M 3.9 ~ 9.1 1.1M ~ 5.1M 1.0 ~ 3.6 5.6M ~ 22M 10 ~ 1M 10 ~ 1M 3.9 ~ 9.1 1.1M ~ 5.1M 1.0 ~ 3.6 5.6M ~ 22M 10 ~ 1M 10 ~ 1M 3.9 ~ 9.1 1.0 ~ 3.6 10 ~ 1M 10 ~ 1M 2.2 ~ 9.1 1.0 ~ 2.0 10 ~ 1M 10 ~ 1M 2.2 ~ 9.1 1.0 ~ 2.0 Resistance Values Operating Temperature Range E-24 & E-96 E-24 & E-96 E-24 E-24 & E96 E-24 & E-96 E-24 E-24 & E96 E-24 & E96 E-24 & E-96 E-24 -55°C ~ +155°C E-24 & E96 E-24 & E96 E-24 & E-96 E-24 E-24 & E96 E-24 & E96 E-24 & E-96 E-24 E-24 & E96 E-24 & E96 E-24 & E-96 E-24 E-24 & E96 E-24 & E96 Power Derating Curve: For operation above 70oC, power ratingmust be derated according to the following chart: 100 Power rating (Watts) x Resistance (Ohms) 80 RATE (%) Note *2 - "Maximum Overload Voltage" for all resistors is the lower of the two values: Resistance Range (Ω)*3 60 40 20 0 -20 Power rating (Watts) x Resistance (Ohms) 20 60 70oC 100 120 155 oC Note *3 - 11Meg ~ 22Meg only available in E-24 values ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 13 Anti-Sulfur Thick Film Chip Resistors NRCS Series ZERO OHM JUMPER RATINGS Jumper EIA Size NRCS04ZO NRCS06ZO NRCS10ZO NRCS12ZO NRCS25ZO NRCS50ZO NRCS100ZO 0402 0603 0805 1206 1210 2010 2512 Power Rating Current at 70°C Rating 0.063W 0.10W 0.125W 0.25W 0.25W 0.50W 1.0W 1.0A 1.0A Overload Maximum Current Resistance Rating 2.0A 2.0A 2.0A 4.0A 2.5A 5.0A 50mΩ Operating Temperature Range -55°C ~ +155°C Typical Performance* (After immersions in cutting fluid with 0.5% Sulfur content) 11/30 opened Δ R/R 100% 26/30 opened 50% *Referential performance measured under certain preconditions and not guaranteed. 0% -50% 250 Hours 500 Hours 1,000 Hours = Standard Thick Film Resistors (30 samples) = NRCS series (30 samples) PART NUMBER SYSTEM (E-24 VALUES) PART NUMBER SYSTEM (E-96 VALUES) NRCS 12 J 103 TR F NRCS 12 F 1002 TR F RoHS compliant RoHS compliant Tape & Reel Packaging Tape & Reel Packaging Resistance Code: First 2 figures are significant, Resistance Code: First 3 figures are significant, 3rd digit is the multiplier, “R” 4th digit is the multiplier, “R” indicates a decimal point. indicates a decimal point. Tolerance Code: G=±2% and J=±5% Tolerance Code: F=±1% Size Size Series Series DIMENSIONS (mm) Type EIA Size L NRCS04 0402 1.0 ± 0.05 W H NRCS06 0603 1.60 ± 0.15 0.80 ± 0.15 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 NRCS10 0805 2.00 ± 0.20 1.25 ± 0.10 0.50 ± 0.10 0.40 ± 0.20 0.40 ± 0.20 NRCS12 1206 3.20 +0.06-0.05 1.60 +0.05-0.15 0.60 ± 0.10 0.50 ± 0.25 0.50 ± 0.20 NRCS25 1210 3.2 ± 0.20 2.50 +0.2-0.1 NRCS50 2010 5.0 ± 0.2 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.5 ± 0.3 NRCS100 2512 6.3 ± 0.2 3.2 ± 0.2 0.6 ± 0.1 0.7 ± 0.2 0.7 ± 0.2 0.50 ± 0.05 0.35 ± 0.05 T t 0.2 ± 0.1 0.25 +0.06-0.05 0.60 ± 0.10 0.50 ± 0.25 0.50 ± 0.20 CONSTRUCTION ® 14 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Anti-Sulfur Thick Film Chip Resistors NRCS Series STANDARD E-12, E-24, E-96 VALUES AND 0603 RESISTANCE CODES E-12 Value 10 12 15 18 22 27 33 39 47 56 68 82 91 E-24 Value 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 E-96 Value Code 100 01 110 05 121 09 133 13 147 17 162 21 178 25 196 29 215 33 237 37 261 41 287 45 316 49 348 53 383 57 422 61 464 65 511 69 562 73 619 77 681 81 750 85 825 89 909 93 Value Code 102 02 113 06 124 10 137 14 150 18 165 22 182 26 200 30 221 34 243 38 267 42 294 46 324 50 357 54 392 58 432 62 475 66 523 70 576 74 634 78 698 82 768 86 845 90 931 94 Value Code 105 03 115 07 127 11 140 15 154 19 169 23 187 27 205 31 226 35 249 39 274 43 301 47 332 51 365 55 402 59 442 63 487 67 536 71 590 75 649 79 715 83 787 87 866 91 953 95 Value Code 107 04 118 08 130 12 143 16 158 20 174 24 191 28 210 32 232 36 255 40 280 44 309 48 340 52 374 56 412 60 453 64 499 68 549 72 604 76 665 80 732 84 806 88 887 92 976 96 CARRIER TAPE DIMENSIONS (mm) Type EIA Case Size NRCS04 Carrier Material A B 0402 0.65 ±0.10 1.15 ±0.10 NRCS06 0603 1.10 ±0.20 1.90 ±0.20 NRCS10 0805 1.65 ±0.20 2.40 ±0.20 NRCS12 1206 2.00 ±0.20 3.50 ±0.20 NRCS25 1210 2.85 ±0.20 NRCS50 2010 2.90 ±0.20 5.40 ±0.20 3.40 ±0.20 6.60 ±0.20 Paper Embossed Plastic NRCS100 2512 W 8.0 ±0.20 F E P1 P2 2.00 ±0.05 n/a D0 t2 1.00 max. 1.0 max 1.75 ±0.05 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 1.50 +0.10 -0 3.50 ±0.20 12.0 ±0.20 5.50 ±0.05 1.10 max. 0.25 max EMBOSSED PLASTIC CARRIER T1 P0 P0 D P2 P2 E Cover tape D E F W Cover tape F W B A t1 0.5 max 3.50 ±0.05 PAPER CARRIER T1 P0 B P1 A T2 T2 P1 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 15 Anti-Sulfur Thick Film Chip Resistors NRCS Series REEL DIMENSIONS (mm) 0402 NRCS06 0603 NRCS10 B C D E W 10,000 D 0805 NRCS12 1206 NRCS25 1210 NRCS50 2010 NRCS100 2512 Qty 60 180 +0.0 +1.0 -3.0 -3.0 13.0 21.0 2.0 ±0.20 ±0.80 ±0.50 9.00 ±0.30 13.0 ±0.30 E 5,000 A NRCS04 A B EIA Case Size C Type 4,000 W LAND PATTERN DIMENSIONS (mm) Type EIA Case Size A B C NRCS04 0402 0.5 1.3 0.5 NRCS06 0603 0.9 2.6 0.7 NRCS10 0805 1.35 3.45 1.1 NRCS12 1206 2.2 4.7 1.4 NRCS25 1210 2.2 5.2 2.15 NRCS50 2010 3.7 6.2 2.15 NRCS100 2512 4.7 7.6 2.75 C A B REFLOW SOLDERING TEMPERATURE PROFILE 300 Peak Temperature 260°C 10 sec. max. 260 220 200 150 100 120 Sec. Time above 230°C 40 sec. max. 50 0 ® 16 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Chip Resistor Arrays/Networks NRSN Series FEATURES • SUPER MINIATURE SIZE AND LOW PROFILE • HIGH DENSITY PACKAGING OFFERS SIGNIFICANT SPACE SAVINGS RoHS • LOWER PRODUCTION COSTS WITH LESS PLACEMENT (UP TO Compliant 8 RESISTORS IN ONE PACKAGE) includes all homogeneous materials • STANDARD FOOTPRINTS MAKE CONVERSIONS EASY *See Part Number System for Details • BOTH FLOW AND REFLOW SOLDERING APPLICABLE SPECIFICATIONS Type Termination Type Size W x L (mm) No. of Resistors & Circuit Power Rating per Resistor @ +70°C Resistance Tolerance Resistance Range Temperature Coeffieient Maximum Working Voltage* Maximum Overload Voltage Operating Temperature Range Type NRSNØ4I2 Concave 1.0 x 1.0 NRSNA4I2 Convex 1.0 x 1.0 NRSNØ4I4 Concave 1.0 x 2.0 NRSNA4I4 Convex 1.0 x 2.0 NRSNØ6I4 NRSNA6I4 Concave Convex 1.6 x 3.2 2R Isolated 2R Isolated 4R Isolated 4R Isolated 4R Isolated 1/16 (.0625W) J(±5%) G(±2%) F(±1%) 3Ω ~ 9.1MΩ 10Ω ~ 1MΩ ±650ppm ±250ppm 1/16 (.0625W) J(±5%) G(±2%) J(±5%) G(±2%) F(±1% J(±5%) G(±2%) J(5%) G(2%) F(±1%) 10Ω ~ 1MΩ 1Ω ~ 1MΩ 10Ω ~ 1MΩ 1Ω ~ 1MΩ ±250ppm ±200ppm ±200ppm ±200ppm 25V 50V 50V 100V -55°C ~ +125°C (derated as shown) NRSNØ6C NRSNØ6D Concave 3.1 x 6.4 Termination Type Size W x L (mm) No. of Resistors & Circuit Power Rating per Resistor @ +70°C 8R Common Resistance Tolerance J (5%) Resistance Range Temperature Coeffieient Maximum Working Voltage* Maximum Overload Voltage Operating Temperature Range * Maximum allowable continuous voltage for all resistors is the lower of the two values: “MAXIMUM WORKING VOLTAGE” as specified, or Power rating (WATTS) x Resistance (OHMS) NRSN12I4 Concave 3.0 x 5.1 4R Isolated 1/8 (0.125W) J (5%) G (2%) 100Ω ~ 470KΩ 10Ω ~ 1MΩ 47Ω ~ 1MΩ ±200ppm ±200ppm ±200ppm 50V 75V 100V 125V -55°C ~ +125°C (derated as shown) ® 28 J(±5%) G(±2%) F(±1%) 1/16 (.0625W) 1/16 (.0625W) 1/16 (.0625W) NIC COMPONENTS CORP. PART NUMBER SYSTEM (E-24 VALUES) NRSN A 4I2 J 103 TR F RoHS compliant Tape & Reel Packaging Resistance Code: First 2 figures are significant, 3rd digit is the multiplier, “R” indicates a decimal point. Tolerance Code: J=5%, G=2%, F=1% Configuration Designator (See circuit schematics and component diagrams for explanation) Termination Type (A=Convexed, Ø=Concave) Series www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Chip Resistor Arrays/Networks NRSN Series CIRCUIT SCHEMATICS NRSNA4I2/∅4I2 Circuit Type “I” Isolated NRSNA4I4/∅4I NRSNA6I/∅6I & NRSN12I Circuit Type “I” Isolated 10 9 8 7 6 10 9 8 7 6 1 2 3 4 5 1 2 3 4 5 NRSN∅6D8 Circuit Type “D” Bussed/Common NRSN∅6C8 Circuit Type “C” Bussed/Common Power Derating Curve: For operation above 70oC, power rating must be derated according to the following chart: NRSNA6I4 4 Elements 100 1.6mm 80 3.2mm 0 -20 20 100 60 70 0.8 Width 140°C 125°C 473 473 NRC06 (X4) 0603 CHIPS 20 473 40 473 60 1.6 Suggested Minimum Spacing 0.5 4.7 Note 1: Zero ohm versions (R<0.050 ohms) are available in the following parts: NRSNØ4I2ZOTR - 0.5A/element (no markings) NRSNA4I2ZOTR - 0.5A/element (no markings) NRSNØ4I4ZOTR - 0.5A/element (no markings) NRSNA4I4ZOTR - 0.5A/element (marked “000”) NRSNØ6I4ZOTR - 1.0A/element (marked “000”) NRSNA6I4ZOTR - 1.0A/element (marked “000”) NRSN12I4ZOTR - 1.5A/element (marked “000”) ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 29 Chip Resistor Arrays/Networks NRSN Series PART DIMENSIONS (mm) Type NRSNA4I2 NRSNØ4I2 NRSNA4I4 NRSNØ4I4 NRSNA6I4 NRSNØ6I4 NRSNØ6C8 NRSNØ6D8 NRSN12I4 W 1.00 ± 0.20 1.00 ± 0.20 1.00 ± 0.20 1.00 ± 0.20 1.60 ± 0.15 1.60 ± 0.15 3.10 ± 0.20 3.10 ± 0.20 3.00 ± 0.20 L 1.00 ± 0.10 1.00 ± 0.10 2.00 ± 0.10 2.00 ± 0.10 3.20 ± 0.20 3.20 ± 0.20 6.40 ± 0.20 6.40 ± 0.20 5.08 ± 0.20 P 0.67 nom. 0.50 nom. 0.50 nom. 0.50 nom. 0.80 nom. 0.80 nom. 1.27 ± 0.20 1.27 ± 0.20 1.27 ± 0.20 T 0.30 ± 0.05 0.30 ± 0.10 0.40 ± 0.10 0.40 ± 0.10 0.50 ± 0.10 0.55 ± 0.10 0.60 ± 0.20 0.60 ± 0.20 0.70 ± 0.20 A 0.33 ± 0.10 0.30 ± 0.10 0.30 ± 0.10 0.30 ± 0.10 0.50 ± 0.10 0.50 ± 0.10 1.00 ± 0.20 1.00 ± 0.20 0.80 ± 0.20 B 0.15 ± 0.10 0.20 ± 0.10 0.20 ± 0.10 0.15 ± 0.10 0.30 ± 0.15 0.35 ± 0.15 0.55 ± 0.20 0.55 ± 0.20 0.60 ± 0.20 C 0.25 ± 0.10 0.25 ± 0.10 0.25 ± 0.10 0.25 ± 0.10 0.30 ± 0.15 0.45 ± 0.15 0.50 ± 0.20 0.50 ± 0.20 0.60 ± 0.20 Terminations P B C B W C W W T A L NRSNA4I2 Terminations P Terminations C P A T L NRSNA4I4, NRSNA6I4 NRSNØ4I2 P T A L P Terminations Terminations C C W W A T A Terminations (all sizes): 100% Sn finish over Ni Barrier L NRSNØ4I4, NRSNØ6I4, NRSN12I4 T L NRSNØ6D8, NRSNØ6C8 LAND PATTERN DIMENSIONS (mm) Type NRSNØ4I2 NRSNA4I2 NRSNØ4I4 NRSNA4I4 NRSNØ6I4J NRSNA6I4J NRSNØ6C8 NRSNØ6D8 NRSN12I4 A 0.50 0.50 0.50 0.50 1.00 1.00 2.20 2.20 2.20 Reflow Soldering B P S 0.28 0.50 0.34 0.33 0.67 0.34 0.28 0.50 0.22 0.28 0.50 0.22 0.40 0.80 0.40 0.40 0.80 0.40 0.50 1.27 0.50 1.27 0.790 1.27 - F 2.00 2.00 2.00 2.00 2.60 2.60 4.20 4.20 4.20 A 0.7 ~ 0.9 0.7 ~ 0.9 1.9 ~ 2.1 1.9 ~ 2.1 1.0 ~ 1.2 Flow Soldering B P 0.3 ~ 0.35 0.8 0.3 ~ 0.35 0.8 0.5 ~ 0.55 1.27 0.5 ~ 0.55 1.27 0.4 ~ 0.45 1.27 F 4.6 ~ 5.6 4.6 ~ 5.6 5.6 ~ 6.2 5.6 ~ 6.2 5.6 ~ 6.2 P P S A S F A B F B NRSNØI2, NRSNA4I2 NRSN04I4, NRSNA4I4, NRSN06I4 & NRSNA6I4 P P A A F F ® NRSNØ12I4 30 NIC COMPONENTS CORP. NRSN∅6D8, NRSN∅6C8 B www.niccomp.com www.lowESR.com www.RFpassives.com B www.SMTmagnetics.com Chip Resistor Arrays/Networks NRSN Series TAPE DIMENSIONS (mm) Type NRSN04I2 NRSNA4I2 NRSN04I4 NRSNA4I4 NRSN06I4 NRSNA6I4 NRSN06C8 NRSN06D8 NRSN12I4 Material A B F 1.20 ± 0.1 1.207 ± 0.1 1.20 ± 0.1 2.20 ± 0.1 1.90 ± 0.1 3.45 ± 0.1 p1 W 2.0 ± 0.1 Paper Plastic 3.5 ± 0.1 3.5 ± 0.05 t2 0.5 max. 1.0 max 1.0 max. 1.4 max. 8.0 ± 0.2 4.0 ± 0.1 6.75 ± 0.1 t1 5.5 ± 0.05 12.0 ± 0.2 5.7 ± 0.1 φ1.5+0.1/-0.0 4.0 ±0.1 t1 F W B A t2 P1 REEL DIMENSIONS (mm) Type NRSN04I2 NRSNA4I2 NRSN04I4 NRSNA4I4 NRSN06I4 NRSNA6I4 NRSN06C8 NRSN06D8 NRSN12I4 A B C D E φ60 -4.0/+3.0 φ180 -4.0/+3.0 φ80 ±2.0 φ13.0 ±2.0 φ21.0 ±1.0 2.0 ±0.5 W Qty/Reel 8.0 ±0.2 10,000 10 ±1.0 5,000 14 ±2.0 4,000 E C B D W ® A NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 31 Thin Film Chip Resistors NTR Series FEATURES • PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT • EIA STANDARD CASE SIZES (0201 ~ 2512) • LOW NOISE, THIN FILM (NiCr) CONSTRUCTION • REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) 15V includes all homogeneous materials *See Part Number System for Details Temperature Coefficient (ppm/°C) Resistance Range (Ω) ±25 ±100 ±5 ±10, ±15 33 ~ 22KΩ 10 ~ 30Ω 49.9 ~ 3KΩ 49.9 ~ 12KΩ ±0.01% (T), ±0.05% (A), ±25, ±50 49.9 ~ 12KΩ ±0.1% (B), ±0.25% (C), ±0.5% (D), ±1% (F) ±25, ±50 10 ~ 205KΩ ±5 24.9 ~ 15KΩ ±0.1% (B), ±0.25% (C), ±0.5% (D) ±0.01% (T) ±0.05% (A) ±0.1% (B), ±0.25% (C), ±0.5% (D), ±1% (F) ±10, ±15 ±10, ±15 ±25, ±50 ±25, ±50 ±25, ±50 ±25, ±50 ±5 ±10, ±15 ±10, ±15 ±25, ±50 ±25, ±50 ±25, ±50 ±25, ±50 ±5 ±10, ±15 ±10, ±15 ±25, ±50 ±25, ±50 ±25, ±50 24.9 ~ 100KΩ 4.7 ~ 332KΩ 24.9 ~ 100KΩ 4.7 ~ 150KΩ 4.7 ~ 1MΩ 2.0 ~ 4.53Ω 24.9 ~ 30KΩ 24.9 ~ 200KΩ 4.7 ~ 499KΩ 24.9 ~ 200KΩ 4.7 ~ 499KΩ 4.7 ~ 2MΩ 1 ~ 4.53Ω 24.9 ~49.9KΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 4.7 ~ 2.49MΩ ±0.25% (C), ±0.5% (D), ±1% (F) ±25, ±50 1.0 ~ 4.53Ω ±5 ±10, ±15 ±10, ±15 ±25, ±50 ±25, ±50 ±25, ±50 ±25, ±50 ±5 ±10, ±15 ±10, ±15 ±25, ±50 ±25, ±50 ±25, ±50 ±25, ±50 24.9 ~ 100KΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 4.7 ~ 3MΩ 1.0 ~ 4.53Ω 24.9 ~ 100KΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 24.9 ~ 499KΩ 4.7 ~ 1MΩ 4.7 ~ 3MΩ 1.0 ~ 4.53Ω Max.*1 Max.*2 EIA Power Rating Working Type Size Overload at 70°C Voltage Voltage NTR02 0201 1/20 (0.050)W RoHS Compliant Resistance Tolerance (Code) ±0.5% (D) ±1.0% (F) 30V ±0.01% (T), ±0.05% (A), ±0.1% (B), ±0.25% (C), ±0.5% (D) NTR04 0402 1/16 (0.063)W 25V 50V ±0.01% (T), ±0.05% (A) NTR06 0603 1/16 (0.063)W 50V 100V ±0.1% (B), ±0.25% (C), ±0.5% (D) ±0.01% (T) ±0.05% (A) ±0.1% (B), ±0.25 (C), ±0.5 (D), ±1% (F) ±0.25 (C), ±0.5 (D), ±1% (F) ±0.01% (T), ±0.05% (A) NTR10 0805 1/10 (0.10) W 100V 200V ±0.1% (B), ±0.25% (C), ±0.5% (D) ±0.01% (T) ±0.05 (A) ±0.1% (B), ±0.25 (C), ±0.5 (D), ±1% (F) ±0.25 (C), ±0.5 (D), ±1% (F) ±0.01% (T), ±0.05% (A), ±0.1% (B) NTR12 1206 1/8 (0.125) W 150V 300V ±0.01% (T), ±0.05% (A), NTR25 2010 1/4 (0.25) W 150V 300V ±0.1% (B), ±0.25% (C), ±0.5% (D) ±0.01% (T) ±0.05% (A) ±0.1% (B), ±0.25% (C), ±0.5% (D), ±1% (F) ±0.25% (C), ±0.5% (D), ±1% (F) ±0.01% (T), ±0.05% (A), NTR50 2512 1/2 (0.50) W 150V 300V ±0.1% (B), ±0.25% (C), ±0.5% (D) ±0.01% (T) ±0.05 (A) ±0.1% (B),±0.25% (C), ±0.5% (D), ±1% (F) ±0.25% (C), ±0.5% (D), ±1% (F) Reistance Values E - 24 E-24 & E-96 ® 32 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thin Film Chip Resistors NTR Series Note *2 - Maximum Overload Voltage for all Note *1 - Maximum allowable continuous Working Voltage resistors is the lower of the two values: "Maximum Overload Voltage” as specified above or for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above or 2x Power rating (Watts) x Resistance (Ohms) Power rating (Watts) x Resistance (Ohms) Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: TYPICAL NOISE CHARACTERISTICS 100 0603 0805 1206 1~9 -95dB -95dB -95dB 10 ~ 49 -85dB -85dB -85dB 50 ~ 99 -85dB -85dB -85dB 100 ~ 4.99K -100dB -100dB -105dB 5K ~ 19.9K -100dB -100dB -100dB 20K ~ 1M -90dB -100dB -100dB Percentage of Power Rating Case Size Resistance Value (Ω) 80 60 40 30 20 0 20 40 60 70 80 100 Temperature °C 120 125°C 140 155 0201 All Other Sizes ENVIRONMENTAL CHARACTERISTICS Item Specification Tol. > 0.05% Tol. < 0.05% Temperature Coefficient of Resistance As specified Short Time Overload Dielectric Withstanding Voltage ΔR ±0.05% ΔR ±0.5% (N/A 0201 Size) As specified Insulation Resistance >1000MΩ Thermal Shock (N/A 0201 Size) Load Life ΔR ±0.05% ΔR ±0.25% ΔR ±0.05% ΔR ±0.2% >7KΩ ΔR ±0.5% Humidty (Steady State) ΔR ±0.05% ΔR ±0.3% Resistance to Dry Heat ΔR ±0.05% ΔR ±0.2% (N/A 0201 Size) ΔR ±0.05% ΔR ±0.2% Bending Strength ΔR ±0.05% ΔR ±0.2% (N/A 0201 Size) Low Temperature Operation Solderability Resistance to Soldering Heat 95% Minimum Coverage ΔR ±0.05% ΔR ±0.2% Test Method* MIL-STD-202, Method 304 +25/-55/+25/+125/-25 JIS-C-5202-5.5 RCWV x 2.5 or Max Overloading Voltage for 5 Seconds MIL-STD-202F Method 301 Apply Max. Overload Voltage for 1 minute MIL-STD-202F Method 302 Apply 100Vdc for 1 minute MIL-STD-202F Method 107G -55°C ~ +150°C, 100 cycles MIL-STD-202F Method 108A RCWV +70°C, 1.5 hours ON, 0.5 hours OFF Total time 1,000 ~ 1,048 hours MIL-STD-202F Method 103B +40°C, 90% ~ 95% RH, RCWV 1.5 hours ON, 0.5 hours OFF Total time 1,000 ~ 1,048 hours JIS-C5202-7.2 96 hours @ +155°C without load JIS-C-502-7.1 1 hour @ -65°C followed by 45 minutes of RCWV JIS-C-5202-6.1.4 Bending Amplitude 3mm for 10 seconds MIL-STD-202F Method 208H 245°C ±5°C, 5 ±0.5 seconds MIL-STD-202F Method 210E 260°C ±5°C for 10 ±1 seconds *0201 testing per IEC 60115 - 1 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 33 Thin Film Chip Resistors NTR Series STANDARD E-24, E-96 VALUES AND 0603 RESISTANCE CODES E-24 Value 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 E-96 Value Code 100 01 110 05 121 09 133 13 147 17 162 21 178 25 196 29 215 33 237 37 261 41 287 45 316 49 348 53 383 57 422 61 464 65 511 69 562 73 619 77 681 81 750 85 825 89 909 93 Value Code 102 02 113 06 124 10 137 14 150 18 165 22 182 26 200 30 221 34 243 38 267 42 294 46 324 50 357 54 392 58 432 62 475 66 523 70 576 74 634 78 698 82 768 86 845 90 931 94 Value Code 105 03 115 07 127 11 140 15 154 19 169 23 187 27 205 31 226 35 249 39 274 43 301 47 332 51 365 55 402 59 442 63 487 67 536 71 590 75 649 79 715 83 787 87 866 91 953 95 Value Code 107 04 118 08 130 12 143 16 158 20 174 24 191 28 210 32 232 36 255 40 280 44 309 48 340 52 374 56 412 60 453 64 499 68 549 72 604 76 665 80 732 84 806 88 887 92 976 96 MULTIPLIER CODE Code A B, b C D, d E Multiplier 100 101 102 103 104 1. No marking on 0402 case size. 2. Marking for 0603 case size: F 105 G 106 H 107 X Y Z 10-1 10-2 10-3 E-24 values and E-96 Series - ± 1% (F), ± 0.5% (D), ± 0.25% (C). ± 0.1% (B) tolerances CODING FORMULA XX Example: X 10.2kΩ = 102 x 102 Ω = 02C 02 C MARKING EXAMPLES 33.2 Ω = 332 x 10 = 51X 51 X -1 Multiplier Code Resistance Code 10Ω = 01X 7.5k Ω = 85B 150k Ω = 18D 1 MegΩ = 01E 3. Marking for 0805, 1206, 2010 and 2512 case sizes: E-24 and E-96 series - ±1%(F), ±0.5% (D), ±0.25%(C), ±0.1% (B) tolerances 4 DIGIT MARKING SYSTEM - First 3 digits are the significant figures, the 4th digit is the mulitplier. "R"= decimal point. Examples: 0R10 = 0.10 ohms, 1R00 = 1.0 ohms, 22R1=22.1 ohms, 3320= 332 ohms, 4751=4.75K ohms, 1132=11.3K ohms, 6493=649K ohms PART NUMBER SYSTEM NTR 10 B 1003 C TR F RoHS compliant Tape & Reel Packaging Temperature Coefficient Code: S = ±5ppm, B = ±10ppm, N = ±15ppm, C = ±25ppm, D = ±50ppm, F =±100ppm Resistance Code: First 3 digits are significant figures (both E-24 and E-96 values), 4th digit is the multiplier, “R” indicates a decimal point. Tolerance Code: T = 0.01%, A = 0.05%, B = ± 0.1%, C = ± 0.25%, D = ± 0.5%, F = ± 1% Power Rating Code Series ® 34 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Thin Film Chip Resistors NTR Series DIMENSIONS (mm) Type NTR02 NTR04 NTR06 NTR10 NTR12 NTR25 NTR50 Power Rating 1/20W 1/16W 1/16W 1/10W 1/8W 1/4W 1/2W EIA Size 0201 0402 0603 0805 1206 2010 2512 L 0.6 ± 0.05 1.0 ± 0.05 1.55 ± 0.10 2.0 ± 0.15 3.05 ± 0.10 4.9 ± 0.15 6.3 ± 0.15 W 0.3 ± 0.05 0.5 ± 0.05 0.8 ± 0.10 1.25 ± 0.15 1.5 ± 0.10 2.4 ± 0.15 3.1 ± 0.15 H 0.23 ± 0.03 0.30 ± 0.05 0.45 ± 0.10 0.55 ± 0.10 0.55 ± 0.10 0.55 ± 0.10 0.55 ± 0.10 Carrier Tape Material Width (mm) Paper 8 T 0.12 ± 0.05 0.2 ± 0.10 0.3 ± 0.20 0.3 ± 0.20 0.42 ± 0.20 0.6 ± 0.30 0.6 ± 0.30 t 0.12 ± 0.05 0.20 ± 0.10 0.30 ± 0.20 0.40 ± 0.25 0.35 ± 0.25 0.50 ± 0.25 0.50 ± 0.25 TAPING SPECIFICATIONS (1) Availability Type Power Rating EIA Size NTR02 NTR04 NTR06 NTR10 NTR12 NTR25 NTR50 1/20W 1/16W 1/16W 1/10W 1/8W 1/4W 1/2W 0201 0402 0603 0805 1206 2010 2512 Fig. A A A A A B B Qty per Reel (pcs) 20,000 10,000 5,000 Plastic 12 4,000 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 35 Thin Film Chip Resistors NTR Series (2) PAPER TAPE DIMENSIONS (mm) FIG. A Type NTR02 NTR04 NTR06 NTR10 NTR12 EIA Size A 0201 0.38 ± 0.03 0402 0.67 ± 0.03 0603 1.10 ±0.05 0805 1.60 ±0.05 1206 2.00 ±0.05 B 0.68 ± 0.03 1.15 ± 0.03 1.90 ±0.05 2.37 ±0.05 3.55 ±0.05 D E F P0 P1 2.0 ± 0.05 1.55 ±0.05 1.75 ±0.10 3.50 ±0.05 4.0 ±0.10 P2 W T 0.31 ± 0.02 0.40 ± 0.03 2.0 ±0.05 8.0 ±0.1 0.60 ± 0.03 4.0 ±0.05 0.75 ± 0.05 FIG. A P0 E D Cover tape F W B P2 A T P1 (2) PLASTIC EMBOSSED TAPE DIMENSIONS (mm) FIG. B Type NTR25 NTR50 EIA Size 2010 2512 A 2.85 ±0.10 3.40 ±0.10 B 5.45 ±0.10 6.65 ±0.10 D E F P0 1.50 ±0.10 1.75 ±0.10 5.50 ±0.05 P1 4.0 ±0.10 P2 W 4.0 ±0.05 2.0 ±0.05 12.0 ±0.1 0.85 ±0.10 D 60∅ ±2 2 ± .0 0. 5 E Cover tape 21 0. 8 11.4 + 1.0 (0402 ~ 1206) 16.4 ± 1.0 (2010 ~ 2512) 180∅ ±3 ± P0 13∅ ±0.5 w1 FIG. B T F W B P2 A T W2 P1 LAND PATTERN DIMENSIONS (mm) Type NTR02 NTR04 NTR06 NTR10 NTR12 NTR25 NTR50 EIA Size 0201 0402 0603 0805 1206 2010 2512 A B C 0.50 0.80 1.00 2.00 3.60 4.90 0.50 0.70 1.00 1.15 1.40 1.60 0.60 ± 0.2 0.90 ± 0.2 1.35 ± 0.2 1.70 ± 0.2 2.40 ± 0.2 3.00 ± 0.2 9.0 + 0.5 (0402 ~ 1206) 14 ± 0.5 (2010 ~ 2512) PEAK REFLOW SOLDERING CONDITIONS 300 260°C 10 Sec. 250 1 ~ 5°C/Sec. 1 ~ 5°C/Sec. 200 150 120 Sec. 100 C 50 ® 36 B 1 ~ 9°C/Sec. 0 A NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Anti-Corrosive Thin Film Chip Resistors NTRC Series FEATURES • • • • • SPECIAL PASSIVATED NiCr FILM FOR SUPERIOR ANTI-CORROSION PROPERTIES EIA STANDARD SIZING 0402, 0603, 0805, 1206, 2010 AND 2512 RoHS SUIT FOR HIGH RELIABILITY APPLICATIONS IN HARSH ENVIRONMENTS Compliant PRECISION TOLERANCE AND TEMPERATURE CHARACTERISTICS includes all homogeneous materials SAC REFLOW SOLDERABLE (THREE TIMES AT 260°C FOR 32 SECONDS) *See Part Number System for Details SPECIFICATIONS Type EIA Power Rating Size at 70°C Max. *1 Working Voltage Max. *2 Overload Voltage NTRC04 0402 0.063W 25V 50V NTRC06 0603 0.063W 50V 100V NTRC10 0805 0.10W 100V 200V NTRC12 1206 0.125W NTRC50 2010 0.25W NTRC100 2512 0.50W 150V Resistance Tolerance Code ±0.10% (B) ±0.25% (C) ±0.50% (D) ±0.10% (B) ±0.25% (C) ±0.50% (D) ±0.10% (B) ±0.25% (C) ±0.50% (D) ±0.10% (B) ±0.25% (C) ±0.50% (D) ±0.10% (B) ±0.25% (C) ±0.50% (D) 300V Note *1 - Maximum allowable continuous Working Voltage for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above or the result of the following formula Temperature Coefficient (ppm/°C) Resistance Range (Ω) ±25ppm (C) ±50ppm (D) 25Ω ~ 25KΩ ±25ppm (C) ±50ppm (D) 25Ω ~ 332KΩ ±25ppm (C) ±50ppm (D) 10Ω ~ 787KΩ ±25ppm (C) ±50ppm (D) 10Ω ~ 1MΩ ±25ppm (C) ±50ppm (D) 10Ω ~ 1MΩ Resistance Values Operating Temperature Range E-24 & E-96 -55°C ~ +155°C Power Derating Curve: For operation above 70oC, power ratingmust be derated according to the following chart: 100 Note *2 - "Maximum Overload Voltage" for all resistors is the lower of the two values: "Maximum Overload Voltage" as specified above or 2x the result of the following formula Power rating (Watts) x Resistance (Ohms) RATE (%) Power rating (Watts) x Resistance (Ohms) 80 60 40 30 20 0 20 40 60 70 80 100 120 140 155°C PART NUMBER SYSTEM (E24 & E-96 VALUES) NTRC 12 B 1002 C TR F RoHS compliant Tape & Reel Packaging Temperature Coefficient: C=±25ppm, D=±50ppm Resistance Code: First 3 figures are significant, 4th digit is the multiplier, “R” indicates a decimal point. Tolerance Code: B=±0.1%, C=±0.25%, D±0.5% Size & Power Rating Code Series ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 37 Anti-Corrosive Thin Film Chip Resistors NTRC Series DIMENSIONS (mm) Type EIA Size NTRC04 0402 1.00 ± 0.05 0.50 ± 0.05 0.30 ± 0.05 0.20 ± 0.10 0.20 ± 0.10 L W H T t NTRC06 0603 1.55 ± 0.10 0.80 ± 0.10 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 NTRC10 0805 2.00 ± 0.15 1.25 ± 0.15 0.55 ± 0.10 0.30 ± 0.20 0.40 ± 0.20 NTRC12 1206 3.05 ± 0.15 1.55 ± 0.15 0.55 ± 0.10 0.42 ± 0.20 0.35 ± 0.25 NTRC50 2010 4.90 ± 0.15 2.40 ± 0.15 0.55 ± 0.10 0.60 ± 0.30 0.50 ± 0.25 NTRC100 2512 6.30 ± 0.15 3.10 ± 0.15 0.55 ± 0.10 0.60 ± 0.30 0.50 ± 0.25 CONSTRUCTION STANDARD E-12, E-24, E-96 VALUES AND 0603 RESISTANCE CODES E-12 Value 10 12 15 18 22 27 33 39 47 56 68 82 91 E-24 Value 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 E-96 Value Code 100 01 110 05 121 09 133 13 147 17 162 21 178 25 196 29 215 33 237 37 261 41 287 45 316 49 348 53 383 57 422 61 464 65 511 69 562 73 619 77 681 81 750 85 825 89 909 93 Value Code 102 02 113 06 124 10 137 14 150 18 165 22 182 26 200 30 221 34 243 38 267 42 294 46 324 50 357 54 392 58 432 62 475 66 523 70 576 74 634 78 698 82 768 86 845 90 931 94 Value Code 105 03 115 07 127 11 140 15 154 19 169 23 187 27 205 31 226 35 249 39 274 43 301 47 332 51 365 55 402 59 442 63 487 67 536 71 590 75 649 79 715 83 787 87 866 91 953 95 Value Code 107 04 118 08 130 12 143 16 158 20 174 24 191 28 210 32 232 36 255 40 280 44 309 48 340 52 374 56 412 60 453 64 499 68 549 72 604 76 665 80 732 84 806 88 887 92 976 96 ® 38 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Anti-Corrosive Thin Film Chip Resistors NTRC Series CARRIER TAPE DIMENSIONS (mm) Type EIA Case Size NTRC04 NTRC06 Carrier Material A B 0402 0.70 ±0.05 1.16 ±0.10 0603 1.10 ±0.05 1.90 ±0.05 1.60 ±0.05 2.37 ±0.05 2.00 ±0.05 3.50 ±0.05 2.85 ±0.10 5.45 ±0.10 3.40 ±0.10 6.65 ±0.10 W 8.0 ±0.10 Paper NTRC10 0805 NTRC12 1206 NTRC50 2010 Embossed Plastic NTRC100 2512 F P1 P2 2.00 ±0.05 n/a E P0 D0 t 0.40 ± 0.03 0.60 ± 0.03 3.50 ±0.05 1.75 ±0.05 12.0 ±0.10 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 0.75 ± 0.03 1.55 ±0.05 0.75 ± 0.03 5.50 ±0.05 1.00 ± 0.20 EMBOSSED PLASTIC CARRIER PAPER CARRIER P0 P0 D P2 P2 D E Cover tape E F W Cover tape F W B B P1 A A T T P1 REEL DIMENSIONS (mm) EIA Case Size NTRC04 0402 NTRC06 0603 NTRC10 0805 A B C W Qty 10,000 C Type NTRC12 1206 NTRC50 2010 NTRC100 2512 60 B 5,000 178 ± 1.0 A 9.00 ± 0.50 +0.50 -3.0 13.0 ± 0.20 13.0 ± 1.50 4,000 W ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 39 Anti-Corrosive Thin Film Chip Resistors NTRC Series LAND PATTERN DIMENSIONS (mm) Type EIA Case Size A B C NTRC04 0402 0.5 0.5 0.60 ± 0.2 NTRC06 0603 0.8 1.0 0.90 ± 0.2 NTRC10 0805 1.0 1.0 1.35 ± 0.2 NTRC12 1206 2.0 1.15 1.70 ± 0.2 NTRC50 2010 3.6 1.4 2.50 ± 0.2 NTRC100 2512 4.9 1.6 3.10 ± 0.2 C A B REFLOW SOLDERING TEMPERATURE PROFILE 300 Peak Temperature 260°C 10 sec. max. 260 220 200 150 100 120 Sec. Time above 230°C 40 sec. max. 50 0 ® 40 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com High Power Thin Film Chip Resistors NTRH Series FEATURES • IMPROVED POWER RATING (HIGHER THAN NTR SERIES) • PRECISE TOLERANCE AND TEMPERATURE COEFFICIENT • EIA STANDARD CASE SIZES (0603 ~ 1206) • LOW NOISE, THIN FILM (NiCr) CONSTRUCTION • REFLOW SOLDERABLE (Pb FREE TERMINATION FINISH) Max.*1 Max.*2 EIA Power Rating Working Overload Size at 70°C Voltage Voltage Type RoHS Compliant includes all homogeneous materials *See Part Number System for Details Resistance Tolerance (Code) Temperature Resistance Reistance Coefficient Range Values (ppm/°C) (Ω) NTRH06 0603 1/10 (0.100)W 50V 100V ±0.1% (B), ±0.25 (C), ±0.5 (D), ±1% (F) ±25, ±50 10 ~ 332KΩ NTRH10 0805 1/8 (0.125) W NTRH12 1206 1/4 (0.250) W 150V 200V 300V 400V ±0.1% (B), ±0.25 (C), ±0.5 (D), ±1% (F) ±0.1% (B), ±0.25 (C), ±0.5 (D), ±1% (F) ±25, ±50 ±25, ±50 4.7 ~ 1MΩ 4.7 ~ 1MΩ E24 & E-96 ENVIRONMENTAL CHARACTERISTICS Item Specification Temperature Coefficient of Resistance As specified Short Time Overload ΔR ± 0.5% Dielectric Withstanding Voltage As specified Insulation Resistance >1000MΩ Thermal Shock ΔR ± 0.25% Load Life ΔR ± 0.5% Humidty (Steady State) ΔR ± 0.5% Resistance to Dry Heat ΔR ± 0.2% Low Temperature Operation ΔR ± 0.5% Bending Strength ΔR ± 0.2% Solderability 95% Minimum Coverage Resistance to Soldering Heat ΔR ± 0.2% Test Method MIL-STD-202, Method 304 +25/-55/+25/+125/-25 JIS-C-5202-5.5 RCWV x 2.5 or Max Overloading Voltage for 5 Seconds MIL-STD-202F Method 301 Apply Max. Overload Voltage for 1 minute MIL-STD-202F Method 302 Apply 100Vdc for 1 minute MIL-STD-202F Method 107G -55°C ~ +150°C, 100 cycles MIL-STD-202F Method 108A RCWV +70°C, 1.5 hours ON, 0.5 hours OFF Total time 1,000 ~ 1,048 hours MIL-STD-202F Method 103B +40°C, 90% ~ 95% RH, RCWV 1.5 hours ON, 0.5 hours OFF Total time 1,000 ~ 1,048 hours JIS-C5202-7.2 96 hours @ +155°C without load JIS-C-502-7.1 1 hour @ -65°C followed by 45 minutes of RCWV JIS-C-5202-6.1.4 Bending Amplitude 3mm for 10 seconds MIL-STD-202F Method 208H 245°C ±5°C, 5 ±0.5 seconds MIL-STD-202F Method 210E 260°C ±5°C for 10 ±1 seconds PART NUMBER SYSTEM NTRH 10 B 1003 C TR F RoHS compliant Tape & Reel Packaging Temperature Coefficient Code: C = ±25ppm, D = ±50ppm Resistance Code: First 3 digits are significant figures (both E-24 and E-96 values), 4th digit is the multiplier, “R” indicates a decimal point. Tolerance Code: B = ± 0.1%, C = ± 0.25%, D = ± 0.5%, F = ± 1% Power Rating Code Series ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 41 High Power Thin Film Chip Resistors NTRH Series Note *2 - Maximum Overload Voltage for all Note *1 - Maximum allowable continuous Working Voltage resistors is the lower of the two values: "Maximum Overload Voltage” as specified above or for all resistors is the lower of the two values: “Maximum Working Voltage” as specified above or 2x Power rating (Watts) x Resistance (Ohms) Power rating (Watts) x Resistance (Ohms) Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: TYPICAL NOISE CHARACTERISTICS 100 0603 0805 1206 4.7 ~ 9 -95dB -95dB -95dB 10 ~ 49 -85dB -85dB -85dB 50 ~ 99 -85dB -85dB -85dB 100 ~ 4.99K -100dB -100dB -105dB 5K ~ 19.9K -100dB -100dB -100dB 20K ~ 1M -90dB -100dB -100dB Percentage of Power Rating Case Size Resistance Value (Ω) 80 60 40 30 20 0 20 40 60 70 80 100 120 140 155 Temperature °C STANDARD E-24, E-96 VALUES AND 0603 RESISTANCE CODES E-24 Value 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 Value Code 100 01 110 05 121 09 133 13 147 17 162 21 178 25 196 29 215 33 237 37 261 41 287 45 316 49 348 53 383 57 422 61 464 65 511 69 562 73 619 77 681 81 750 85 825 89 909 93 Value Code 102 02 113 06 124 10 137 14 150 18 165 22 182 26 200 30 221 34 243 38 267 42 294 46 324 50 357 54 392 58 432 62 475 66 523 70 576 74 634 78 698 82 768 86 845 90 931 94 E-96 Value Code 105 03 115 07 127 11 140 15 154 19 169 23 187 27 205 31 226 35 249 39 274 43 301 47 332 51 365 55 402 59 442 63 487 67 536 71 590 75 649 79 715 83 787 87 866 91 953 95 MULTIPLIER CODES B, Code A C D, d E F G H X Y Z b Value Code 0 1 2 3 4 5 6 7 -1 -2 -3 10 10 10 10 10 10 10 10 10 10 Multiplier 10 107 04 118 08 1. Marking for 0603 case size is a three character code. The 130 12 code includes two characters to denote the value (based on 0603 143 16 Resistance Codes Table and a third character that denotes the value multiplier (see multiplier codes table). 158 20 174 24 CODING FORMULA MARKING EXAMPLES 191 28 10Ω = 01X XX X 210 32 7.5k Ω = 85B 232 36 150k Ω = 18D Multiplier Code 255 40 Resistance Code 1 MegΩ = 01E 280 44 309 48 2. The 0805 and 1206 case sizes parts use the standard four 340 52 character marking metthod as shown in the examples below. 374 56 412 60 E-24 and E-96 series - ±0.5% (D), ±0.25%(C), ±0.1% (B) tolerances 453 64 4 DIGIT MARKING SYSTEM - First 3 digits are the significant figures, the 4th digit is the mulitplier. "R"= decimal point. 499 68 549 72 Examples: 0R10 = 0.10 ohms, 1R00 = 1.0 ohms, 22R1=22.1 604 76 ohms, 3320= 332 ohms, 4751=4.75K ohms, 1132=11.3K ohms, 665 80 6493=649K ohms 732 84 806 88 887 92 976 96 ® 42 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com High Power Thin Film Chip Resistors NTRH Series DIMENSIONS (mm) Type NTRH06 NTRH10 NTRH12 Power Rating 1/10W 1/8W 1/4W EIA Size 0603 0805 1206 L 1.55 ± 0.10 2.0 ± 0.15 3.05 ± 0.10 W 0.8 ± 0.10 1.25 ± 0.15 1.5 ± 0.10 H 0.45 ± 0.10 0.55 ± 0.10 0.55 ± 0.10 T 0.3 ± 0.20 0.3 ± 0.20 0.42 ± 0.20 t 0.30 ± 0.20 0.40 ± 0.25 0.35 ± 0.25 TAPING SPECIFICATIONS (1) Availability Type Power Rating EIA Size NTRH06 NTRH10 NTRH12 1/10W 1/8W 1/4W 0603 0805 1206 Carrier Tape Material Width (mm) Paper Qty per Reel (pcs) 8 5,000 E F (2) PAPER TAPE DIMENSIONS (mm) Type EIA Size NTRH06 0603 NTRH10 0805 NTRH12 1206 A 1.10 ±0.05 1.60 ±0.05 2.00 ±0.05 B 1.90 ±0.05 2.37 ±0.05 3.55 ±0.05 D 1.55 ±0.03 1.75 ±0.05 3.50 ±0.05 P0 P1 P2 4.0 ±0.10 4.0 ±0.05 W T 0.60 ±0.03 2.0 ±0.05 8.0 ±0.1 w1 0.75 ±0.05 11.4 + 1.0 (0402 ~ 1206) 16.4 ± 1.0 (2010 ~ 2512) D F W 2 ± .0 0. 5 B T 21 0. 8 60∅ ±2 Cover tape ± 13∅ ±0.5 E 180∅ ±3 P0 P2 A P1 W2 PEAK REFLOW SOLDERING CONDITIONS 300 LAND PATTERN DIMENSIONS (mm) 260°C 10 Sec. 250 1 ~ 5°C/Sec. 1 ~ 5°C/Sec. 200 9.0 + 0.5 (0402 ~ 1206) 14 ± 0.5 (2010 ~ 2512) Type NTRH06 NTRH10 NTRH12 EIA Size 0603 0805 1206 A 0.80 1.00 2.00 150 B 0.70 1.00 1.15 C 0.90 ± 0.2 1.35 ± 0.2 1.70 ± 0.2 C 120 Sec. 100 B 50 1 ~ 9°C/Sec. A 0 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 43 Current Sensing Chip Resistors NCST Series FEATURES • • • • RoHS Compliant SURFACE MOUNTABLE 0402 ~ 7520 CASE SIZE PRECISON TOLERANCE (±1%) POWER RATINGS UP TO 3 WATTS Pb-FREE REFLOW COMPATIBLE includes all homogeneous materials *See Part Number System for Details CHARACTERISTICS Type EIA Size Power Rating at 70°C Resistance Tolerance Temperature Coefficient (°C) Resistance Range Resistance Range (Codes) NCST04 0402 1/16W 1% (F) 2% (G) 5% (J) NCST06 0603 1/10W NCST10 0805 1/8W NCST12* 1206 1/4W ±200ppm (F) ±300ppm (G) ±400ppm (H) ±200ppm (F) ±300ppm (G) ±400ppm (H) ±600ppm (J) ±200ppm (F) 501mΩ ~ 1Ω 101mΩ ~ 500mΩ 50mΩ ~ 100mΩ 501mΩ ~ 1Ω 101mΩ ~ 500mΩ 51mΩ ~ 100mΩ 20mΩ ~ 50mΩ 501mΩ ~ 1Ω R501 ~ 1R00 R101 ~ R500 R050 ~ R100 R501 ~ 1R00 R101 ~ R500 R051 ~ R100 R020 ~ R050 R501 ~ 1R00 ±300ppm (G) 51mΩ ~ 500mΩ R051 ~ R500 NCST50* 2010 3/4W ±400ppm (H) 21mΩ ~ 50mΩ R021 ~ R050 ±600ppm (J) 10mΩ ~ 20mΩ R010 ~ R020 ±300ppm (G) 1mΩ ~ 4mΩ R001 ~ R004 ±150ppm (X) 11mΩ ~ 350mΩ R011 ~ R350 ±200ppm (F) 5mΩ ~ 10mΩ R005 ~ R010 ±100ppm (E) ±150ppm (X) ±200ppm (F) ±300ppm (G) 31mΩ ~ 3.0Ω 21mΩ ~ 30mΩ 6mΩ ~ 20mΩ 3mΩ ~ 5mΩ R031 ~ 1R00 R021 ~ R030 R006 ~ R020 R003 ~ R005 NCST100* 2512 NCST200 1% (F) 2% (G) 5% (J) 1W 7520 NCST300 1% (F) 2% (G) 5% (J) 2% (G) 5% (J) 1% (F) 2% (G) 5% (J) 2W 1225 1% (F) 2% (G) 5% (J) 3W Operating Temp. Range (°C) -55°C ~ +155°C *Available with a ±100ppm (E) TCR (100mΩ ~ 1Ω) Percentage of Power Rating Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: 100 80 60 40 30 155°C 20 0 0 20 40 60 70 80 100 120 140 160 Temperature °C ® 44 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCST Series ENVIRONMENTAL CHARACTERISTICS Item Specification Test Method Temperature Coefficient of Resistance As Specified MIL-STD-202, Method 304 +25/-55/+25/+125/+25°C Thermal Shock ±0.5% MIL-STD-202, Mehtod 107G -55°C ~ +150°C, 100 cycles Short Time Overload ±0.5% JIS-C-5202-5.5 RCWV x 2.5 or Max. Overloading Voltage for 5 sec. Dielectric Withstanding Voltage by Type MIL-STD-202F Method 301 Apply Max. Overload Voltage for 1 minute Insulation Resistance >1000MΩ MIL-STD-202F Method 302 Apply 100Vdc for 1 minute Resistance to dry heat ±0.5% JIS-C-5202-7.2 96 hrs @ 155°C without load Load Life ±1% MIL-STD-202 Method 108 RCWV @ 70°C, cycles of 1.5 hours ON, 0.5 hrs OFF for 1,000 ~ 1,048 hrs Resistance to Soldering Heat ±0.5% MIL-STD-202F Method 210E 260°C ±5°C for 10 sec. ±1 sec. Humidity (Steady State) ±0.5% MIL-STD-202 Method 103B 40°C, 90 ~ 95% RH, RCWV 1.5 hours ON, 0.5 hours OFF, total 1000 ~ 1048 hours Low Temperature Operation ±0.5% JIS-C-5202-7.1 1 hour -65°C followed by 45 minutes of RCWV Solderability 95% min. coverage MIL-STD-202F Method 208H 245°C ±5°C for 5 sec. ±0.5 sec. Bending Strength As Specified JIS-C-5202-6.1.4 Bending Amplitude 3mm for 10 seconds PART NUMBER SYSTEM NCST10 F R501 F TR F RoHS compliant Packaging: TR = Tape & Reel TCR Code: E=100ppm, X=150ppm, F=200ppm, G=300ppm, H=400ppm, J=600ppm Resistance Code: See examples Tolerance Code: J=5%, G=2%, F=1% Series and Size ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 45 Current Sensing Chip Resistors NCST Series AVAILABLE VALUES AND PART NUMBERS Available Value Range Part Number Resistance Value (mΩ) NCST04 * R050HTRF 50 NCST04 * R050HTRF NCST04 * R101GTRF 100 101 NCST04 * R501FTRF NCST04 * R501FTRF 500 501 NCST04 * 1R00FTRF NCST06 * R020JTRF 1,000 Resistance Value (mΩ) 20 NCST06 * R050JTRF NCST06 * R051HTRF 50 51 NCST06 * R100HTRF NCST06 * R101GTRF 100 101 NCST06 * R500GTRF NCST06 * R501FTRF 500 501 NCST06 * 1R00FTRF NCST10 * R020JTRF 1,000 Resistance Value (mΩ) 20 NCST10 * R050JTRF NCST10 * R051HTRF 50 51 NCST10 * R100HTRF NCST10 * R101GTRF 100 101 NCST10 * R500GTRF NCST10 * R501FTRF 500 501 NCST10 * 1R00FTRF NCST12 * R010JTRF 1,000 Resistance Value (mΩ) 10 NCST12 * R020JTRF NCST12 * R021HTRF 20 21 NCST12 * R050HTRF NCST12 * R051GTRF 50 51 NCST12 * R500GTRF NCST12 * R501FTRF 51 501 NCST12 * 1R00FTRF NCST12 * R100ETRF 1,000 100 NCST12 * 1R00ETRF 1,000 ±400ppm (H) 50mΩ ~ 100mΩ 0402 Size 1/16W ±300ppm (G) 101mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω Available Value Range Part Number ±400ppm (H) 51mΩ ~ 100mΩ ±300ppm (G) 101mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω Available Value Range Part Number ±400ppm (H) 51mΩ ~ 100mΩ ±300ppm (G) 101mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω Available Value Range Part Number Available TCR ±600ppm (J) 10mΩ ~ 20mΩ ±400ppm (H) 21mΩ ~ 50mΩ 1206 Size 1/4W Available TCR ±600ppm (J) 20mΩ ~ 50mΩ 0805 Size 1/8W Available TCR ±600ppm (J) 20mΩ ~ 50mΩ 0603 Size 1/10W Available TCR ±300ppm (G) 51mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω ±100ppm (E) 100mΩ ~ 1.0Ω *Tolerance Codes: 1% (F), 2% (G) or 5% (J) ® 46 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCST Series AVAILABLE VALUES AND PART NUMBERS Available Value Range NCST50 * R010JTRF Resistance Value (mΩ) 10 NCST50 * R020JTRF NCST50 * R021HTRF 20 21 NCST50 * R050HTRF NCST50 * R051GTRF 50 51 NCST50 * R500GTRF NCST50 * R501FTRF 500 501 NCST50 * 1R00FTRF NCST50 * R100ETRF 1,000 100 NCST50 * 1R00ETRF NCST100 * R010JTRF 1,000 Resistance Value (mΩ) 10 NCST100 * R020JTRF NCST100 * R021HTRF 20 21 NCST100 * R050HTRF NCST100 * R051GTRF 50 51 NCST100 * R500GTRF NCST100 * R501FTRF 500 501 NCST100 * 1R00FTRF NCST100 * R100ETRF 1,000 100 NCST100 * 1R00ETRF NCST200 * R001GTRF 1,000 Resistance Value (mΩ) 1 NCST200 * R004GTRF NCST200 * R005FTRF 4 5 NCST200 * R010FTRF NCST200 * R011XTRF 10 51 NCST200 * R350XTRF NCST300 * R003GTRF 500 Resistance Value (mΩ) 3 NCST300 * R005GTRF NCST300 * R006FTRF 5 6 NCST300 * R020FTRF NCST300 * R021XTRF 20 21 NCST300 * R030XTRF NCST300 * R031ETRF 30 31 NCST300 * 3R00ETRF 3,000 Part Number ±600ppm (J) 10mΩ ~ 20mΩ ±400ppm (H) 21mΩ ~ 50mΩ 2010 Size 3/4W ±300ppm (G) 51mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω ±100ppm (E) 100mΩ ~ 1.0Ω Available Value Range Part Number ±400ppm (H) 21mΩ ~ 50mΩ ±300ppm (G) 51mΩ ~ 500mΩ ±200ppm (F) 501mΩ ~ 1.0Ω ±100ppm (E) 100mΩ ~ 1.0Ω Available Value Range Part Number ±200ppm (F) 5mΩ ~ 10mΩ ±150ppm (X) 11mΩ ~ 350mΩ Available Value Range Part Number Available TCR ±300ppm (G) 3mΩ ~ 5mΩ 1225 Size 3W Available TCR ±300ppm (G) 1mΩ ~ 4mΩ 7520 Size 2W Available TCR ±600ppm (J) 10mΩ ~ 20mΩ 2512 Size 1W Available TCR ±200ppm (F) 6mΩ ~ 20mΩ ±150ppm (X) 21mΩ ~ 30mΩ ±100ppm (E) 31mΩ ~ 3.0Ω *Tolerance Codes: 1% (F), 2% (G) or 5% (J) ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 47 Current Sensing Chip Resistors NCST Series DIMENSIONS (mm) Type Case Size Length (L) Width (W) Thickness (T) 0.32 ±0.05 TerminatIon Width (P1) 0.25 ±0.10 TerminatIon Width (P2) 0.20 ±0.10 NCST04 0402 1.00 ±0.05 0.50 ±0.05 NCST06 0603 1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.30 ±0.20 0.30 ±0.20 NCST10 0805 2.00 ±0.10 NCST12 1206 3.05 ±0.15 1.25 ±0.10 0.50 ±0.10 0.30 ±0.20 0.30 ±0.20 1.55 ±0.15 0.60 ±0.10 0.50 ±0.20 NCST50 2010 0.40 ±0.20 5.00 ±0.20 2.45 ±0.15 0.60 ±0.10 0.60 ±0.30 0.50 ±0.25 NCST100 NCST200 2512 6.35 ±0.20 3.15 ±0.15 0.60 ±0.10 0.60 ±0.30 0.50 ±0.25 7520 2.00 ±0.20 7.50 ±0.30 0.60 ±0.10 0.40 ±0.20 0.40 ±0.20 NCST300 1225 3.10 ±0.15 6.30 ±0.15 0.90 ±0.15 0.60 ±0.30 0.55 ±0.25 Case Sizes 0402, 0603, 0805, 1206, 2010 & 2512 Case Sizes 1225 & 7520 L R100 L W W P2 T P1 P2 T P1 LAND PATTERN DIM. (mm) A B C NCST04 0.50 0.50 0.60 ±0.2 NCST06 0.70 0.80 0.90 ±0.2 NCST10 1.00 1.00 1.35 ±0.2 NCST12 1.15 2.00 1.70 ±0.2 NCST50 1.40 3.60 2.40 ±0.2 NCST100 1.60 4.90 3.00 ±0.2 NCST200 2.00 1.20 7.60 ±0.2 NCST300 2.00 2.00 7.60 ±0.2 C A B ® 48 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCST Series PAPER CARRIER TAPE DIMENSIONS (mm) Type A B W NCST04 0.67 ±0.03 1.15 ±0.03 NCST06 1.10 ±0.05 1.90 ±0.05 NCST10 1.60 ±0.05 2.37 ±0.05 NCST12 2.00 ±0.05 3.55 ±0.05 F E P1 P2 φD P0 T 2.00 ±0.05 8.00 ±0.10 3.50 ±0.05 1.75 ±0.05 0.40 ±0.03 2.00 ±0.05 4.00 ±0.10 4.00 ±0.10 0.60 ±0.03 1.55 ±0.05 0.75 ±0.05 B W F E ∅ Do Component P2 P1 A Forward Direction P0 T EMBOSSED PLASTIC CARRIER DIMENSIONS (mm) Type A B W F K 12.0 ±0.10 5.50 ±0.05 1.00 ±0.20 NCST50 2.85 ±0.10 5.45 ±0.10 NCST100 3.40 ±0.20 6.65 ±0.10 NCST200 2.50 ±0.20 8.30 ±0.20 16.0 ±0.30 7.80 ±0.05 1.50 ±0.10 NCST300 3.38 ±0.10 6.68 ±0.10 12.0 ±0.10 5.50 ±0.05 1.45 ±0.20 E P1 P2 P0 φDo T 1.75 ±0.10 4.00 ±0.05 2.00 ±0.05 4.00 ±0.05 1.50 ±0.05 0.80 ±0.10 E T P0 B W F D0 A P K REEL DIMENIONS (mm) AND QUANTITY Type A B C W NCST04 C Quantity 10,000 NCST06 9.0 ±0.50 NCST10 5,000 NCST12 NCST50 B 178 ±1.0 60 +0.5 13 ±0.20 13.2 ±1.50 4,000 NCST200 17 ±0.50 2,000 NCST300 13.2 ±1.50 2,000 NCST100 W ® NIC COMPONENTS CORP. A www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 49 Surface Mount Current Sensing Resistors FEATURES • ULTRA LOW RESISTANCE VALUES • THIN FILM CONSTRUCTION • IDEAL FOR CURRENT SENSING APPLICATIONS • HIGHER POWER RATING IN REDUCED SIZE CHARACTERISTICS Type size Power Rating at 70°C NCSH02 NCSH04 0201 1/10 (0.100W) 0402 1/8 (0.125W) NCSH06 0603 1/8 (0.125W) NCSH10 0805 1/4 (0.250W) NCSH12 1206 1/2 (0.500W) Resistance Tolerance (Code) ±2% (G), ±5% (J) ±1% (F), ±2% (G) ±1% (F) ±1% (F), ±2% (G) ±1% (F), ±2% (G) ±1% (F), ±2% (G) ±2% (G) NCSH Series RoHS Compliant includes all homogeneous materials *See Part Number System for Details Temperature Coefficient (ppm/°C) 0 ~ 200 (S) 0 ~ 200 (S) 0 ~ 100 (R) 0 ~ 200 (S) 0 ~ 100 (R) 0 ~ 200 (S) 0 ~ 350 (T) ±100 (F) 0 ~ 200 (S) 0 ~ 350 (T) 0 ~ 350 (T) 0 ~ 500 (T) Resistance Range (Ω) 0.1 ~ 4.7 0.05 ~ 4.7 0.1 ~ 6.8 0.02 ~ 0.091 0.1 ~ 10 0.043 ~ 0.091 0.01 ~ 0.039 0.051 ~ 4.7 0.033 ~ 0.047 0.027 0.018 ~ 0.022 0.01 ~ 0.015 Resistance Value Operating Temperature Range (°C) E-24 -55°C ~ +125°C L DIMENSIONS (mm) Series NCSH02 NCSH04 NCSH06 NCSH10 NCSH12 L 0.60 ± 0.05 1.00 ± 0.10 1.60 ± 0.10 2.00 ± 0.20 3.20 ± 0.20 W 0.30 ± 0.05 0.50 ± 0.10 0.80 ± 0.10 1.25 ± 0.20 1.60 ± 0.20 T 0.23 ± 0.05 0.35 ± 0.10 0.45 ± 0.45 0.40 ± 0.20 0.50 ± 0.15 P 0.12 ± 0.05 0.20 ± 0.10 0.20 ± 0.15 0.40 ± 0.20 1.00 ± 0.15 W T P PART NUMBER SYSTEM NCSH 06 G R020 S TR F RoHS compliant Tape and Reel Packaging Temperature Coefficient Code (see characteristics table) Resistance Value Code "R" denotes decimal point, value in ohms Tolerance Code: F (1%), G (2%), J (5%) Case Size/Power Rating Code: (see specifications tables) Series Percentage of Power Rating Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: 100 90 80 70 60 50 40 30 20 10 0 0 125°C 20 100 120 40 60 70 Temperature °C ® 50 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Current Sensing Resistors NCSH Series LAND PATTERN DIM. (mm) A B C NCSH02 0.24 0.28 0.34 NCSH04 0.55 0.50 0.60 NCSH06 0.70 1.00 1.20 NCSH10 1.40 1.20 1.65 NCSH12 1.40 2.20 2.00 C B A PAPER CARRIER TAPE DIMENSIONS (mm) Type A B NCSH02 0.38 ±0.03 0.68 ±0.03 W NCSH04 0.63 ±0.03 1.13 ±0.03 NCSH06 1.10 ±0.10 1.90 ±0.10 NCSH10 1.65 ±0.20 2.40 ±0.20 NCSH12 2.00 ±0.20 3.60 ±0.20 F E P1 P2 φD P0 T 0.31 ± 0.02 2.00 ±0.05 8.00 ±0.10 3.50 ±0.05 1.75 ±0.05 0.42 ±0.05 2.00 ±0.05 4.00 ±0.10 4.00 ±0.10 1.50 +1.0/-0 0.60 ±0.05 0.75 ±0.05 B W F E ∅ Do Component A P1 P2 P0 Forward Direction T REEL DIMENIONS (mm) AND QUANTITY Type A B C W NCSH02 10,000 NCSH04 NCSH06 C Quantity 178 ±1.0 60 +0.5 NCSH10 13 ±0.20 9.0 ±0.50 5,000 B NCSH12 W ® NIC COMPONENTS CORP. A www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 51 Current Sensing Chip Resistors NCSR Series FEATURES • • • • • SURFACE MOUNTABLE 1206, 2010 AND 2512 CASE SIZE RoHS Compliant PRECISON TOLERANCE (±1%) AND TCR (±50PPM) TO +170°C TAPED & REEL PACKAGING FOR EASY PICK AND PLACE REFLOW COMPATIBLE includes all homogeneous materials See Part Number System for Details SPECIFICATIONS EIA Size Type Power Rating at 80°C NCSR100S 1206 1 Watt NCSR150 2010 1.5 Watt NCSR100 1 Watt NCSR200 2 Watt 2512 NCSR250 2.5 Watt NCSR300 3 Watt *See Part Number Tables for Available Value/ TCR Resistance Tolerance (Code) Temperature Coefficient (ppm/°C) Resistance Range ±50 (D) 1.0mΩ ~ 10mΩ ±50 (D)* ±75 (W)* ±100 (E)* ±150 (K)* 0.50mΩ ~ 22mΩ 0.50mΩ ~ 10mΩ 4.0mΩ ~ 6.0mΩ 0.50mΩ ~ 3.0mΩ ±1% (F) ±3% (H) ±5% (J) Operating Temperature Range (°C) -55°C ~ +170°C ENVIRONMENTAL CHARACTERISTICS Specification Type 1 Type 2 Item Temperature Coefficient of Resistance Thermal Shock Short Time Overload Resistance to dry heat Load Life Resistance to Soldering Heat Solderability Test Method MIL-STD-202, Method 304 As Specified +25/-55/+25/+125/+25°C MIL-STD-202, Mehtod 107G ±0.5% ±1% -55°C ~ +150°C, 100 cycles JIS-C-5202-5.5 ±0.5% ±1% 5x rated power for 5 seconds JIS-C-5202-7.2 ±1% ±1% 96 hrs @ 155°C without load MIL-STD-202 Method 108 ±1% ±1% RCWV @ 70°C, cycles of 1.5 hours on, 0.5 hrs off for 1,000 ~ 1,048 hrs MIL-STD-202F Method 210E ±0.5% ±1% 260°C ±5°C for 10 sec. ±1 sec. MIL-STD-202F Method 208H 95% min. coverage 245°C ±5°C for 5 sec. ±0.5 sec. Case Type 1 Sn Solder Plating Cu Plating Alloy Plating Protective Coating (Black) Percentage of Power Rating Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: 100 80 60 40 30 20 0 20 40 60 70 80 100 170 Temperature °C Case Type 2 Protective Coating (Green) Metal Strip PART NUMBER SYSTEM NCSR 100 S F R015 K TR G F RoHS compliant Case Type (Blank = Case 1, G = Case 2) Packaging: TR = Tape & Reel TCR Code: D=50ppm, W=75ppm E=100ppm, K=150ppm Resistance Code: See Values Tables Tolerance Code: J=5%, H=3%, F=1% Case Code (S = Reduced Size, Blank = Standard) Power Rating (100 = 1W, 150 = 1.5W, 200 = 2W, 250 = 2.5W and 300 = 3W) Sn Solder Plating ® Series 52 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCSR Series NCSR100S (1 WATT, 1206 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) NCSR100S*R001DTRGF 1.0 NCSR100S*1M50DTRGF 1.5 NCSR100S*R002DTRGF 2.0 NCSR100S*2M50DTRGF 2.5 NCSR100S*R003DTRGF 3.0 NCSR100S*3M50DTRGF 3.5 NCSR100S*R004DTRGF 4.0 NCSR100S*4M50DTRGF 4.5 NCSR100S*R005DTRGF 5.0 NCSR100S*5M50DTRGF 5.5 NCSR100S*R006DTRGF 6.0 NCSR100S*6M50DTRGF 6.5 NCSR100S*R007DTRGF 7.0 NCSR100S*R008DTRGF 8.0 NCSR100S*R010DTRGF 10 Available Tolerance Available TCR Length (L) Width (W) Thickness (T) TerminatIon Width (P) Case Type ±1% (F) ±3% (H) ±5% (J) ±50ppm (D) 3.20 ±0.25 1.60 ±0.15 0.60 ± 0.20 0.98 ±0.38 2 Width (W) Thickness (T) TerminatIon Width (P) Case Type 1.30 ±0.30 1 1.30 ±0.30 1 1.93 ± 0.75 2 NCSR100 (1 WATT, 2512 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) NCSR100*M50DTRF 0.50 1.40 ± 0.20 NCSR100*M75DTRF 0.75 1.00 ± 0.20 NCSR100*R001DTRF NCSR100*1M50DTRF NCSR100*R002DTRF 1.0 1.5 2.0 NCSR100*2M50KTRF 2.5 NCSR100*R003KTRF NCSR100*3M50KTRF NCSR100*R004ETRF NCSR100*4M50ETRF NCSR100*R005ETRF NCSR100*5M50ETRF NCSR100*R006WTRF NCSR100*6M50WTRF NCSR100*R007WTRF NCSR100*R011DTRGF NCSR100*R012DTRGF NCSR100*R013DTRGF NCSR100*R014DTRGF NCSR100*R015DTRGF NCSR100*R016DTRGF NCSR100*R017DTRGF NCSR100*R018DTRGF NCSR100*R019DTRGF NCSR100*R020DTRGF NCSR100*R021DTRGF NCSR100*R022DTRGF 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 11 12 13 14 15 16 17 18 19 20 21 22 Available Tolerance Available TCR Length (L) ±50ppm (D) ±1% (F) ±3% (H) ±5% (J) 6.35 ±0.25 3.18 ±0.25 0.80 ± 0.80 0.65 ± 0.20 0.50 ± 0.20 1.00 ± 0.20 ±150ppm (K) ±100ppm (E) 6.35 ±0.25 3.18 ±0.25 6.35 ± 0.25 3.18 ± 0.35 ±75ppm (W) 0.70 ± 0.20 0.71 ± 0.20 0.60 ± 0.20 0.58 ± 0.20 0.50 ± 0.20 0.47 ± 0.20 0.50 ± 0.20 0.47 ± 0.20 0.45 ± 0.20 ±1% (F) ±3% (H) ±5% (J) ±50ppm (D) 0.60 ± 0.20 * Insert appropriate tolerance code ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 53 Current Sensing Chip Resistors NCSR Series NCSR150 (1.5 WATT, 2010 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) NCSR150*R001DTRGF 1.0 NCSR150*1M50DTRGF 1.5 NCSR150*R002DTRGF 2.0 NCSR150*2M50DTRGF 2.5 NCSR150*R003DTRGF 3.0 NCSR150*3M50DTRGF 3.5 NCSR150*R004DTRGF 4.0 NCSR150*4M50DTRGF 4.5 NCSR150*R005DTRGF 5.0 NCSR150*5M50DTRGF 5.5 NCSR150*R006DTRGF 6.0 NCSR150*6M50DTRGF 6.5 NCSR150*R007DTRGF 7.0 NCSR150*R008DTRGF 8.0 NCSR150*R010DTRGF 10 Available Tolerance Available TCR Length (L) Width (W) Thickness (T) TerminatIon Width (P) Case Type ±1% (F) ±3% (H) ±5% (J) ±50ppm (D) 5.08 ±0.25 2.54 ±0.35 0.6 ±0.20 1.67 ± 0.63 2 Width (W) Thickness (T) TerminatIon Width (P) Case Type 1.30 ± 0.30 1 1.93 ±0.75 2 NCSR200 (2 WATT, 2512 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) Available Tolerance Available TCR Length (L) NCSR200*M50DTRF 0.50 1.4 ±0.20 NCSR200*M75DTRF 0.75 1.0 ± 0.20 NCSR200*R001DTRF 1.0 0.8 ± 0.20 NCSR200*1M50DTRF 1.5 0.65 ± 0.20 NCSR200*R002DTRF 2.0 NCSR200*R007DTRGF 7.0 NCSR200*7M50DTRGF 7.5 NCSR200*R008DTRGF 8.0 NCSR200*8M50DTRGF 8.5 NCSR200*R009DTRGF 9.0 NCSR200*9M50DTRGF 9.5 NCSR200*R010DTRGF 10 0.5 ± 0.20 ±1% (F) ±3% (H) ±5% (J) ±50ppm (D) 6.35 ±0.25 3.18 ±0.35 0.6 ± 0.20 NCSR250 (2.5 WATT, 2512 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) NCSR250*R004DTRGF 4.0 NCSR250*4M50DTRGF 4.5 NCSR250*R005DTRGF 5.0 NCSR250*5M50DTRGF 5.5 NCSR250*R006DTRGF 6.0 Available Tolerance Available TCR Length (L) Width (W) Thickness (T) TerminatIon Width (P) Case Type ±1% (F) ±3% (H) ±5% (J) ±50ppm (D) 6.35 ±0.25 3.18 ±0.35 0.60 ±0.20 1.93 ±0.75 2 * Insert appropriate tolerance code ® 54 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCSR Series NCSR300 (3 WATT, 2512 CASE SIZE) AVAILABLE VALUES Part Number Resistance Value (mΩ) NCSR300*M50ETRGF 0.50 NCSR300*M75ETRGF 0.75 NCSR300*R001DTRGF 1.0 NCSR300*1M50DTRGF 1.5 NCSR300*R002DTRGF 2.0 NCSR300*R003WTRGF 3.0 NCSR300*3M50WTRGF 3.5 Available Tolerance Available TCR Length (L) Width (W) Thickness (T) ±50ppm (D) Case Type 1.93 ±0.75 2 0.60 ±0.20 ±100ppm (E) ±1% (F) ±3% (H) ±5% (J) TerminatIon Width (P) 6.35 ±0.25 3.18 ±0.35 0.60 ±0.20 ±75ppm (W) * Insert appropriate tolerance code TYPE 1 TYPE 2 L L R007 R007 W W T T P P 2-WIRE LAND PATTERN DIM. (mm) 4-WIRE LAND PATTERN DIM. (mm) (no traces between pads to avoid short circuit) Recommended for precision current sensing (no traces between pads to avoid short circuit) Case Size A B C B C D 0.90 2.375 1.95 Case Size A 1206 2010 1.44 3.80 3.12 1206 0.90 2.375 0.725 0.5 2512 1.80 4.75 3.6 2010 1.44 3.80 1.65 0.80 2512 1.80 4.75 1.45 1.00 C C A D B A B ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 55 Current Sensing Chip Resistors 300 NCSR Series RECOMMENDED REFLOW SOLDERING TEMPERATURE PROFILE Peak Temperature 260°C 250 1 ~ 5°C/Sec. 1 ~ 5°C/Sec. 200 10 Sec. 150 100 50 120 Sec. 1 ~ 9°C/Sec. 0 TAPE DIMENSIONS (mm) Case Resistance A Size Values 1206 All 1.90 ±0.1 2010 All 2.85 ±0.1 0.50 3.40 ±0.1 2512 0.75 3.50 ±0.1 1 ~ 22 3.40 ±0.1 B 3.60 ±0.1 5.55 ±0.1 6.70 ±0.1 6.80 ±0.1 6.70 ±0.1 K Case 1 Case 2 n/a 0.80 ±0.2 n/a 0.80 ±0.2 1.40 ± 0.2 0.80 ±0.2 0.80 ±0.2 0.80 ±0.2 P P1 E 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 4.0 ±0.1 1.75 ±0.1 1.75 ±0.1 1.75 ±0.1 1.75 ±0.1 1.75 ±0.1 F W Quantity per Reel 8.0 ±0.2 12.0 ±0.3 12.0 ±0.3 12.0 ±0.3 12.0 ±0.3 2,000 D0 3.50 ±0.05 1.55 ±0.05 5.50 ±0.05 1.50 ±0.1 5.50 ±0.05 1.50 ±0.1 5.50 ±0.05 1.50 ±0.1 5.50 ±0.05 1.50 ±0.1 E EMBOSSED PLASTIC CARRIER P B D1 W F D0 A K P1 Notice: 1. The cumulative tolerance of 10 sprocket hole pitch is ±0.2mm. 2. Carrier camber shall be not more than 1mm per 100mm through a length of 250mm. 3. A & B measured 0.3mm from the bottom of the packet 4. K measured at a point on the inside bottom of the packet to the top surface of the carrier. 5. Pocket position relative to sprocket hole is measured as the true position of the pocket and not the pocket hole. ® 56 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Current Sensing Resistors NCSW Series FEATURES • ULTRA LOW RESISTANCE VALUES • PRECISION TOLERANCE AND TEMPERATURE STABILITY • THIN FILM CONSTRUCTION RoHS • IDEAL FOR CURRENT SENSING APPLICATIONS Compliant includes all homogeneous materials • AVAILABLE IN 1 WATT ~ 2 WATT POWER RATINGS *See Part Number System for Details CHARACTERISTICS Type size Power Rating NCSW100 0815 1W @ +70°C NCSW200 0830 2W @ +30°C Resistance Tolerance (Code) Temperature Coefficient (ppm/°C) ±50 (Q), ±100 (R) 0 ~ +200 (S) 1% (F), 2% (G) 0 ~ +350 (T) ±1% (F), 2% (G) ±50 (Q), ±100 (R) ±1% (F), 2% (G) 0 ~ +200 (S) ±5% (J) 0 ~ +350 (T) Resistance Range (Ω) 0.1 ~ 1.0 0.01 ~ 0.068 0.002 ~ 0.009 0.1 ~ 0.47 0.01 ~ 0.068 0.001 ~ 0.009 Resistance Value Operating Temperature Range (°C) E-6 -55°C ~ +125°C E-6 -55°C ~ +155°C DIMENSIONS (mm) Series NCSW100 NCSW200 L W 3.75 ± 0.30 7.50 ± 0.30 L 2.00 ± 0.20 2.00 ± 0.20 T 0.55 max. 0.55 max. P 0.40 ± 0.20 0.40 ± 0.20 PART NUMBER SYSTEM NCSW 100 F R010 S TR F R010 RoHS compliant Tape and Reel Packaging Temperature Coefficient Code (see characteristics table) Resistance Value Code "R" denotes decimal point, value in ohms Tolerance Code: F (1%), G (2%), J (5%) Power Rating Code: 100 = 1W, 200 = 2W W T Series P Power Derating Curve: For operation above +70°C for NCSW100 and +30°C for NCSW200, power rating must be derated according to the following chart: NCSW200 125°C 20 100 120 40 60 70 Temperature °C Percentage of Power Rating Percentage of Power Rating NCSW100 100 90 80 70 60 50 40 30 20 10 0 0 100 90 80 70 60 50 40 30 20 10 0 0 155°C 20 30 40 60 80 100 120 140 160 Temperature °C ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 57 Surface Mount Current Sensing Resistors NCSW Series LAND PATTERN DIMENSIONS (mm) A B C NCSW100 1.4 1.2 7.9 NCSW200 1.4 1.2 15.8 C B A EMBOSSED PLASTIC CARRIER DIMENSIONS (mm) B ± 0.2 W ± 0.3 F ± 0.10 NCSW100 2.40 4.25 12.0 5.50 NCSW200 2.40 8.00 16.0 7.50 E ± 0.1 P0 ± 0.1 P1 ± 0.1 φD ± 0.05 1.75 4.0 4.0 1.55 φD1 ± 0.05 T ± 0.05 K ± 0.2 0.3 0.7 - E T P0 D0 B D1 W A ± 0.1 F Type A Type NCSW100 NCSW200 A B C 180 +3/-0 60 +1/-0 13.0 ± 0.2 P1 K REEL DIMENIONS (mm) AND QUANTITY W Quantity 9.0 ± 0.3 4,000 17.0 ± 0.3 4,000 E C B D W ® 58 NIC COMPONENTS CORP. A www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Current Sensing Chip Resistors NCSP Series FEATURES RoHS Compliant • SURFACE MOUNTABLE, MOLDED FLAT PACK • ULTRA LOW VALUES (3mΩ ~ 1Ω) • EXTEND TEMPERATURE RANGE (+180°C) • Pb-FREE REFLOW COMPATIBLE includes all homogeneous materials *See Part Number System for Details CHARACTERISTICS Size Power Rating Resistance at 70°C Tolerance NCSP100S 6.3 x 3.2 NCSP100L 7.5 x 4.5 NCSP200 12.5 X 6.0 NCSP300 14.5 X 8.0 Rated Voltage = 1 Watt 1% (F) 5% (J) 2 Watt 3 Watt Temperature Coefficient (°C) Resistance Resistance Range Range (Codes) 0.003Ω ~ 0.200Ω R003 ~ R200 For Values 0.003Ω ~ 0.510Ω R003 ~ R510 0.051Ω ∼ 0.100Ω: ±50ppm For Values 0.005Ω ~ 1.000Ω R005 ~ 1R00 <0.051Ω and >0.100Ω: ±100ppm 0.005Ω ~ 1.800Ω R005 ~ 1R80 Operating Temp. Range (°C) -55°C ~ +155°C -55°C ~ +180°C Power rating (Watts) x Resistance (Ohms) ENVIRONMENTAL SPECIFICATIONS Item PART NUMBER SYSTEM Specification Test Method Temperature Coefficient of Resistance As Specified Measured from 20°C through a temperature range of -55°C ~ +125°C Short Time Overload ΔR < 0.5% Applied voltage equivalent to 2x the rated power for 10 minutes Withstanding Voltage (Between terminations and center of component body) ΔR < 0.2% with no evidence of insulation breakdown 500VAC for 1 minute Insulation Resistance (Between terminations and center of component body) >100MΩ 100VDC Resistance to dry heat ΔR < 0.5% 260°C ± 5°C for 10 seconds Humidity (Steady State) ΔR < 0.5% IR > 20MΩ No Mechanical Damage +40°C, 90~95% RH for 1,000 hours Endurance (1,000 hours) ΔR < 1.0% No mechanical damage Rated power at 70°C Power on 90 minutes Power off 30 minutes Temperature Cycling (5 cycles) ΔR < 0.5% No mechanical damage -55°C 30 minutes +25°C 3 minutes +155°C 30 minutes +25°C 3 minutes Resistance to Soldering Heat ΔR < 0.5% No mechanical damage 260°C ± 5°C for 10 seconds Vibration ΔR < 0.5% No mechanical damage 1.5mm in X, Y, Z axis 10Hz ~ 55Hz ~ 10Hz 1 minute sweep for 2 hours in each direction Solderability Coverage of more than 75% of termination 245°C ± 5°C for 2 seconds Solder: Sn3Ag0.5Cu NCSP200 F R051 D TR F RoHS compliant Packaging: TR = Tape & Reel TCR Code: D = ±50ppm E = ±100ppm Resistance Code: See characteristics table Tolerance Code: J=±5% and F=±1% Series Power Derating Curve: For operation above 70°C, power rating must be derated according to the following chart: Percentage of Power Rating Type 100 80 60 40 20 0 0 20 40 60 70 80 Type NCSP100S 155°C L ± 0.5 W ± 0.3 H ± 0.3 T1 ± 0.3 T2 ± 0.3 T3 ± 0.3 NCSP100S NCSP100L NCSP200 NCSP300 6.3 7.5 12.5 14.5 3.2 4.5 6.0 8.0 1.0 2.0 3.0 3.0 3.2 2.5 4.0 6.0 H L www.lowESR.com 0.8 1.1 1.5 1.5 T2 T1 ® 0.8 1.2 2.0 2.0 Molded Plastic Case Terminations: 100% Sn Finish over Nickel Barrier www.niccomp.com 120 140 160 180 DIMENSIONS (mm) Copper/Nickel Alloy Resistive Element NIC COMPONENTS CORP. 100 Temperature °C www.RFpassives.com T3 W www.SMTmagnetics.com 59 Current Sensing Chip Resistors RECOMMENDED REFLOW SOLDERING TEMPERATURE PROFILE LAND PATTERN DIMENSIONS (mm) Type A B C NCSP100S 2.0 3.2 3.0 NCSP100L 2.0 4.5 3.0 NCSP200 2.8 7.9 4.5 NCSP300 2.8 9.9 6.5 NCSP Series 300 Peak Temperature 260°C 250 1 ~ 3°C/Sec. 3 ~ 6°C/Sec. 200 5 ~ 10 sec. max. 150 60 ~ 120 Sec. 100 C 50 0 B A 1 ~ 3°C/Sec. EMBOSSED PLASTIC CARRIER DIMENSIONS (mm) Type A ±0.1 B ±0.1 NCSP100S 3.6 6.8 NCSP100L 5.1 8.2 NCSP200 6.6 13.2 NCSP300 8.6 15.2 P ±0.1 P1 ±0.1 8.0 4.0 12.0 K ±0.1 W ±0.2 F ±0.1 1.3 12.0 5.5 2.5 16.0 7.5 3.5 24.0 11.5 E ±0.1 Do +0.1 T ±0.05 1.75 1.50 0.3 E T P1 D0 NCSP100L NCSP200 NCSP300 180±2.0 254±0.3 330 ±0.2 B C W Quantity W A 13.0 ±0.5 60 13.0 ±0.5 80 ±0.5 17.5 ±0.5 B Type NCSP100S F REEL DIMENIONS (mm) AND QUANTITY 1,000 25.5 ±0.5 A P K E C B D W ® A 60 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount NTC Thermistors NCT Series FEATURES • NEGATIVE TEMPERATURE COEFFICIENT • FAST RESPONSE TO TEMPERATURE VARIATIONS MAKE THEM IDEALLY FOR TEMPERATURE SENSORS AND COMPENSATORS RoHS • STANDARD EIA 0402, 0603 AND 0805 SIZES Compliant includes all homogeneous materials • NICKEL BARRIER SOLDER PLATE TERMINATIONS • TAPE AND REEL FOR AUTOMATIC MOUNTING *See Part Number System for Details CHARACTERISTICS AND PERFORMANCE Series EIA Size Resistance Range (+25°C) Resistance Tolerance (+25°C) Operating Temperature Range Storage Temperature Range Maximum Power Rating (JIS-C2570)* Dissipation Factor Thermal Time Constant NCT02 0201 470 ohm ~ 1Megohm NCT04 NCT06 NCT08 0402 0603 0805 470 ohm ~ 2Megohm 100 ohm ~ 2Megohm 100 ohm ~ 2Megohm 1% (F), ±2% (G), ±3% (H), 5% (J), 10% (K) -40°C ~ +125°C -40°C ~ +125°C 110mW 110mW 120mW 130mW <1.5mW/°C (power to heat thermistor 1°C, measured at 25°C) Within 5 seconds (time to change 63.2% from initial to stable) D = +25°C ~ +50°C A = +25°C ~ +85°C E = +25°C ~ +100°C 2610K ~ 4800K ±1% (F), ±2% (G), ±3% (H), ±5% (J) +260°C ± 5°C for 10 ±1 seconds +125°C ± 3°C for 1,000 hours, ΔR ±3%, ΔBeta ±2% -40°C ± 3°C for 1,000 hours, ΔR ±3%, ΔBeta ±2% +85°C ± 2°C, 85% ±5% RH for 1,000 hours, ΔR ±3%, ΔBeta ±2% 100 cycles of -40°C ±3°C 30 min., +20°C 3 min., +125°C ±3°C 30 min., +20°C 30 min. ΔR ±3%, ΔBeta ±2% Functional Beta Temperature Range Beta Value Range Beta Value Tolerance Resistance to Soldering Heat High Temperature Stability Low Temperature Stability Humidity Temperature Cycliing *JIS-C2570: Maximum power for continuous load at 25°C. DIMENSIONS (mm) Series NCT02 NCT04 NCT06 NCT08 EIA Size 0201 0402 0603 0805 L 0.60 ± 0.03 1.0 ± 0.05 1.6 ± 0.15 2.0 ± 0.20 W T max. P 0.30 ± 0.03 0.23 ± 0.03 0.15 ± 0.05 0.50 ± 0.05 0.40 0.25 +0.05/-0.10 0.80 ± 0.15 0.60 0.30 ± 0.20 1.25 ± 0.20 0.65 0.40 ± 0.20 Termination Material Ag Base Termination Ni Barrier 100% Sn Finish STANDARD RESISTANCE VALUES (@25°C) AND BETA RANGE* Beta Value 4610 ~ 4800K 4410 ~ 4600K 4210 ~ 4400K 4010 ~ 4200K 3810 ~ 4000K 3610 ~ 3800K 3410 ~ 3600K 3210 ~ 3400K 3010 ~ 3200K 2810 ~ 3000K 2610 ~ 2800K NCT02 (0201) NCT04 (0402) NCT06 (0603) NCT08 (0805) 100K ~ 1M 30K ~ 150K 20K ~ 120K 10K ~ 100K 10K ~ 50K 6.8K ~ 30K 2K ~ 20K 2K ~ 20K 1K ~ 5K 1K ~ 3K 470 ~ 1.5K 100K ~ 2M 10K ~ 2M 10K ~ 2M 10K ~ 220K 2K ~ 150K 2K ~ 150K 2K ~ 150K 2K ~ 150K 680 ~ 68K 500 ~ 47K 100 ~ 10K 68K ~ 2M 10K ~ 2M 10K ~ 2M 1K ~ 220K 1K ~ 150K 1K ~ 150K 1K ~ 150K 1K ~ 150K 470 ~ 150K 150 ~ 100K 100 ~ 1K 47K ~ 2M 10K ~ 2M 6.8K ~ 2M 1K ~ 220K 1K ~ 150K 1K ~ 150K 1K ~ 150K 680 ~ 150K 220 ~ 150K 100 ~ 100K 100 ~ 1K E-24 Standard Values 1.0 1.3 1.8 2.4 3.3 4.3 5.6 7.5 1.1 1.5 2.0 2.7 3.6 4.7 6.2 8.2 1.2 1.6 2.2 3.0 3.9 5.1 6.8 9.1 T W P L *Beta can be ordered in increments of 10 (ex. 2610, 2620, 2630, etc.) PART NUMBER SYSTEM NCT06 D J 154 H 410 TR F RoHS compliant Packaging, TR: Tape and Reel Beta Code (1st Three Characters of Beta Value) Beta Value Tolerance: J=±5%, H=±3%, G=±2%, F=±1% Resistance Value Code (E-24 Standard Values) Resistance Value Tolerance: K+±10%, J=±5%, H=±3%, G=±2%, F=±1% Temperature Characteristic (D=+25°C ~ +50°C, A=+25°C ~ +85°C, E+25°C ~ +100°C) ® NIC COMPONENTS CORP. Series www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 61 Surface Mount NTC Thermistors NCT Series CARRIER TAPE DIMENSIONS (mm) Type A B W NCT02 0.68 ±0.20 0.38 ±0.02 NCT04 0.65 ±0.10 1.15 ±0.10 NCT06 1.10 ±0.20 1.90 ±0.20 NCT08 1.65 ±0.20 2.40 ±0.20 F E P1 φD P0 2.00 ±0.05 8.00 ±0.20 3.50 ±0.05 4.00 ±0.10 1.75 ±0.10 1.55 ±0.05 4.00 ±0.05 T1 T2 0.42 ±0.02 0.50 max. 0.50 max. 1.00 max. 1.00 max. 1.40 max. φD P0 t1 F W B A t2 P1 REEL DIMENSIONS (mm) AND QUANTITY Type A +0/-3 B +1/-0 C ±0.20 W ±0.3 180 60 13 9.0 Quantity NCT02 NCT04 NCT06 10,000 NCT08 5,000 E C B D W A ® 62 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Transient Voltage Suppressors NVS Series FEATURES • ZINC OXIDE MULTILAYER CONSTRUCTION RoHS • HIGH ENERGY SURGE VOLTAGE PROTECTION Compliant • EIA SIZES 0603, 0805, 1206 AND 1210 includes all homogeneous materials • HIGH CURRENT RATING (UP TO 500A) *See Part Number System for Details • FAST RESPONSE (LESS THAN 1nS) • LOW CLAMPING VOLTAGES • Pb-FREE COMPATIBLE WITH FLOW AND REFLOW SOLDERING Multilayer zinc oxide chip varistors are ideal for the suppression of voltage transients due to ESD, inductive discharge and electromagnetic energy. The NVS series of chip varistors were designed to provide transient protection to new, low voltage semiconductors and to aid in equipment compliance to CIS/IEC 801 specifications. CHARACTERISTICS Size Specifications Working Voltage Range (@50μA Maximum Leakage Current) Clamping Voltage Range (Based on 20 - 10 Amp 8/20μS Pulse) Peak Current Rating (8/20μS Pulse Waveform) Maximum Transient Energy Dissipated (10/1000μS Pulse Waveform) 0603 0805 1206 1210 3.3 ~ 30V 3.3 ~ 30V 3.3 ~ 48V 18 ~ 60V 10 ~ 65V 10 ~ 65V 10 ~ 100V 39 ~ 120V 30A 30 ~ 120A 30 ~ 150A 220 ~ 500A 0.1J 0.1 ~ 0.3J 0.1 ~ 0.4J 0.9 ~ 1.5J PART NUMBERING SYSTEM NVS 0805 F 400 A TR F RoHS Compliant Tape and Reel Energy A = 0.1J B = 0.3J C = 0.4J D = 0.9J E = 1.2J F = 1.5J G = 2.0J Clamping Voltage 100 = 10V 150 = 15.5V 200 = 20V 250 = 25V 300 = 30V 390 = 39V 400 = 40V 560 = 56V 580 = 58V 620 = 62V 650 = 65V 101 = 100V 121 = 120V Case Size 0603 0805 1206 1210 Working Voltage (Vdc), Breakdown Voltage (Vdc min.@1mA DC) A = 3.3V(5.0V) E = 14V(18.5V) I = 48V(62V) B = 5.6V(8.5V) F = 18V(25.5V) J = 60V(75V) C = 9.0V(12.7V) G = 26V(34.5V) D = 12V (16V) H = 30V(41V) Series ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 63 Surface Mount Transient Voltage Suppressors NVS Series PART NUMBERING SPECIFICATIONS Part Number Working* Voltage (Max.) Clamping Voltage (Max.) Peak Current (Max.) Transient Energy (Max.) NVS0603A100ATRF NVS0603B150ATRF NVS0603C200ATRF NVS0603E300ATRF NVS0603F400ATRF NVS0603G580ATRF NVS0603H650ATRF NVS0805A100ATRF NVS0805A100BTRF NVS0805B150ATRF NVS0805B150BTRF NVS0805C200ATRF NVS0805D250ATRF NVS0805E300ATRF NVS0805E300BTRF NVS0805F400ATRF NVS0805F400BTRF NVS0805G580ATRF NVS0805G580BTRF NVS0805H650ATRF NVS1206A100ATRF NVS1206A100CTRF NVS1206B150ATRF NVS1206B150CTRF NVS1206E300ATRF NVS1206E300CTRF NVS1206F400ATRF NVS1206F400CTRF NVS1206G580CTRF NVS1206H650CTRF NVS1206I101CTRF NVS1210F390FTRF NVS1210G560ETRF NVS1210H620DTRF NVS1210H620ETRF NVS1210I101DTRF NVS1210I101ETRF NVS1210J121FTRF 3.3V 5.6V 9.0V 14V 18V 26V 30V 3.3V 3.3V 5.6V 5.6V 9.0V 12V 14V 14V 18V 18V 26V 26V 30V 3.3V 3.3V 5.6V 5.6V 14V 14V 18V 18V 26V 30V 48V 18V 26V 30V 30V 48V 48V 60V 12V 18V 22V 32V 42V 60V 67V 12V 12V 18V 18V 22V 27V 32V 32V 42V 42V 60V 60V 67V 12V 12V 18V 18V 32V 32V 42V 42V 60V 67V 100V 42V 60V 67V 67V 100V 100V 120V 30A 30A 30A 30A 30A 30A 30A 40A 120A 40A 120A 40A 40A 40A 120A 30A 100A 30A 100A 30A 40A 150A 40A 150A 40A 150A 30A 150A 120A 120A 100A 500A 300A 220A 280A 220A 250A 250A 0.1J 0.1J 0.1J 0.1J 0.1J 0.1J 0.1J 0.1J 0.3J 0.1J 0.3J 0.1J 0.1J 0.1J 0.3J 0.1J 0.3J 0.1J 0.3J 0.1J 0.1J 0.4J 0.1J 0.4J 0.1J 0.4J 0.1J 0.4J 0.4J 0.4J 0.4J 1.5J 1.2J 0.9J 1.2J 0.9J 1.2J 1.5J Case Size 0603 0805 1206 1210 Typical C (nF) 1.450 0.750 0.550 0.350 0.150 0.155 0.125 1.400 5.000 1.100 3.000 0.750 0.525 0.325 0.900 0.225 0.550 0.120 0.250 0.090 1.250 4.700 1.200 3,000 0.600 1.050 0.350 0.900 0.500 0.400 0.225 3.100 2.150 1.750 1.850 0.450 0.500 0.400 L (nH) <1.0 <1.0 <1.0 <1.0 <1.0 <1.0 <1.0 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.5 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <1.7 <2.0 <2.0 <2.0 <2.0 <2.0 <2.0 <2.0 DIMENSIONS (mm) W Case Size 0603 0805 1206 1210 T P P L Termination Material: 100% Sn finish over Ni barrier over Pd-Ag base. Length (L) 1.6 ± 0.15 2.0 ± 0.20 3.2 ± 0.20 3.2 ± 0.20 Width (W) 0.8 ± 0.15 1.2 ± 0.20 1.6 ± 0.20 2.5 ± 0.20 Thickness (T) Overlap (P) 0.9 max. 0.5 max. 1.0 max. 0.8 max. 1.0 max. 0.8 max. 1.0 max. 0.8 max. REEL QUANTITIES Case Size 0603 0805 1206 1210 178mm (7") 1,000 or 4,000 1,000 or 4,000 1,000 or 4,000 1,000 or 4,000 254mm (10") 10,000 10,000 10,000 10,000 NOTES: 1. *Working voltage is a maximum recommended working voltage and is specified for operation at leakage current less than 50μA.. 2. Peak current and clamping voltage is specified under 8/20uS test conditions. 3. Transient energy specified under 10/1000uS test condition. 4. Storage Temperature/Humidity: +5°C ~ +35°C, RH 40% ~ 75% ® 64 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Varistor NVT Series FEATURES RoHS Compliant • ULTRA LOW CAPACITANCE (AS LOW AS 0.8pF) includes all homogeneous materials • EIA SIZES 0402 AND 0603 *See Part Number System for Details • MEETS STANDARDS OF IEC 61000-4-2, LEVEL 4 • IDEAL FOR USB2.0, IEEE1394 & HDMI HIGH SPEED DATA APPLICATIONS • Pb-FREE REFLOW PROCESS COMPATIBLE SPECIFICATIONS Case Size 0402 0603 0402 0603 Part Number Maximum WVDC NVT0402H100A800TRF NVT0402H5R0B800TRF NVT0402H5R0D500TRF NVT0402H180D800TRF NVT0402H180D171TRF NVT0603H100A800TRF NVT0603H5R0D500TRF NVT0603H180D800TRF NVT0603H180D171TRF NVT0402S6R7S120TRF NVT0402S110R180TRF NVT0402S130R220TRF NVT0402S160L270TRF NVT0402S160J270TRF NVT0402S300M420TRF NVT0603S6R7T120TRF NVT0603S110S180TRF NVT0603S130S220TRF NVT0603S160Q270TRF NVT0603S160L270TRF NVT0603S160J270TRF NVT0603S260Q330TRF NVT0603S300N420TRF 1mA Voltage (nominal) 10 5 5 18 18 10 5 18 18 6.7 11 13 16 16 30 6.7 11 13 16 16 16 26 30 80 80 50 80 170 80 50 80 170 12 18 22 27 27 42 12 18 22 27 27 27 33 42 Capacitance (pF) 1MHz Max. 1 2 3 3 3 1 3 3 3 220 150 150 47 20 56 330 220 220 100 47 20 100 68 1KHz Typical Typical 0.8 1.5 2.1 2.1 2.1 0.8 2.1 2.1 2.1 150 175 120 140 100 116 33 37 15 16.5 40 45 250 290 180 210 160 185 85 100 33 37 15 16.5 85 100 55 63 Max. Peak Current at 8/20μS, 2 Times 10 10 10 10 3 10 20 20 20 20 20 3 20 15 Max. ESD IEC 61000-4-2 Type Contact discharge 8kV High Speed, Ultra Low Capacitance Contact discharge 8kV Low Speed, Low Capacitance Notes: 1. Maximum Allowable Voltage - max. DC voltage that can be applied continuously within the operating temperature of the part (-40°C ~+85°C). 2. Varistor Voltage - varistor starting voltage between terminals at 1mA DC (also known as the breakdown voltage) 3. Maximum Peak Current - the max. current under the standard pulse 8/20μS, 2 times based on IEC60. 4. Maximum ESD - the max. current under ESD based on IEC 61000-4-2, 10 times (5 times each positive-negative polarity). PART NUMBERING SYSTEM NVT 0603 S 110 S 180 TR F RoHS Compliant Tape & Reel 1mA Voltage Capacitance Code (See Specifications Table) Maximum Working Voltage Product type: H = Ultra low capacitance S = Standard Case Size Series DIMENSIONS (mm) Case Size L 0402 1.00 ± 0.05 0603 1.60 ± 0.10 W 0.50 ± 0.05 0.80 ± 0.10 T 0.50 ± 0.05 0.80 ± 0.10 P 0.20 ± 0.10 0.30 ± 0.20 T W P L Termination Material: Silver (Ag) base, Nickel (Ni) barrier, 100% Sn finish ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 65 Surface Mount Varistor NVT Series RECOMMENDED LAND PATTERN DIMENSIONS (mm) Reflow Soldering A B C 0.4 ~ 0.5 0.4 ~ 0.5 0.4 ~ 0.5 0.8 ~ 1.0 0.6 ~ 0.8 0.6 ~ 0.8 Case Size 0402 0603 RECOMMENDED REFLOW SOLDERING TEMPERATURE PROFILE 300 1 ~ 4°C/Sec. 220 200 C 2 ~ 5°C/Sec. 150 Time above 220°C 60 Sec. 100 B 10 Sec. Peak Temperature 260°C 260 120 Sec. B A 50 0 CARRIER TAPE DIMENSIONS (mm) A B NVT0402 Type 0.62 ±0.05 1.12 ± 0.05 NVT0603 1.00 ± 0.10 1.80 ± 0.10 W F E 8.0 ± 0.2 3.50 ±0.05 1.75 ±0.10 P1 T1 T2 Qty/Reel 2.00 ±0.05 0.7 max. 1.0 max. 10,000 4.00 ± 0.05 1.1 max. 1.4 max. 4,000 NVT0603 NVT0402 φ1.5+0.1/-0.0 φ1.5+0.1/-0.0 4.0 ±0.1 4.0 ±0.1 t1 t1 A F F W B t2 t2 P1 A W B P1 E REEL DIMENSIONS (mm) C A +0/-3 B +1/-0 C ± 0.5 D ± 0.8 E ± 0.5 W ± 0.3 180 60 13 21.0 2.0 9.0 B D W A ® 66 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Varistor NVT Series CROSS REFERENCE GUIDE NIC P/N Amotech AVX EPCOS ICT Littlefuse Panasonic TDK NVT0603S6R7S120TRF AVL3M03300 VC06033A100 - ICVN1003A100 V3.5MLA0603 EZJZ1V120JA NVT0402S6R7S120TRF AVL5M02200 VC04025X150 - ICVN0505X150 V5.5MLA0402 EZJZ0V120JA NVT0603S6R7S120TRF AVL5M03300 VC060305A150 CN0603M4G ICVN1005A150 EZJZ1V120KA NVT0402S6R7S120TRF AVL8M02200 VC04029X200 - ICVN0509X200 V5.5MLA0603 V9MLA0402 V9MLA0402L AVR-M1005C080MTAAB AVR-M1005C080MTABB AVR-M1005C080MTACB AVR-M1608C080MTAAB EZJZ0V120JA AVR-M1005C120MTAAB NVT0603S6R7S120TRF AVL8M03300 VC060309A200 NVT0402S160L270TRF NVT0603S160Q270TRF NVT0402S160L270TRF NVT0603S160Q270TRF AVL11L02200 AVL11L03300 AVL14K02200 AVL14K03300 NVT0402S160L270TRF ICVN1009A200 V9MLA0603 EZJZ1V120KA AVR-1608C120MT6AB VC040214X300 VC060314A300 CN0603M6G CN0603M7G CN0603L8G CN0603K11G ICVN0514X300 ICVN1014A300 EZJZ0V270EA EZJZ1V270GA EZJZ0V270EA EZJZ1V270GA AVR-M1608C180MT6AB AVL18K02200 VC040218X400 NC0402L14GK2 - EZJZ0V270EA - NVT0603S160Q270TRF AVL18K03300 VC060318A400 CN0603K14G - V14MLA0402 V14MLA0603 V18MLA0402 V18MLE0402 V18MLA0603 V18MLE0603 NVT0402S160L270TRF - - - ICVN0518X400 - NVT0603S160Q270TRF - - CN0603K17G NC0603K17LCG ICVN1018A400 - NVT0603S260Q270TRF - VC060325A580 NC0603K20G ICVN1026A580 V26MLA0603 EZJZ1V270GA EZJZ0V270EA EZJZ0V270RA EZJZ1V270GA EZJZ1V270GA EZJZ1V270EA EZJZ1V270RA EZJZ1V330GA AVR-M1608C220KT6AB AVR-M1608C220KT2AB AVR-M1005C270MTAAB AVR-M1005C270MTABB AVR-M1608C270KT6AB AVR-M1608C270KT2AB AVR-M1608C270KTAAB AVR-M1608C270KTABB - NIC P/N EPCOS AVX ICT Panasonic Littlefuse NVT0402H5R0D500TRF NVT0402H100A800TRF NVT0603H100A800TRF NVT0402H100A800TRF NVT0603H180D800TRF CM0603V650RFGK2 VC04AG183R0YA1 VC06AG183R0YA1 - EZJZ0V500AA EZJZ0V80010 EZJZ1V80010 EZJZ0V800AA EZJZ1V800AA V0402MHS03 - ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 67 Surface Mount ESD Suppressor NXED Series FEATURES • IDEAL FOR USB2.0, IEEE1394 & HDMI HIGH SPEED DATA APPLICATIONS • SUPER LOW CAPACITANCE (AS LOW AS 0.05pF) RoHS Compliant • EIA SIZES 0402 AND 0603 includes all homogeneous materials • MEETS STANDARDS OF IEC 61000-4-2, LEVEL 4 *See Part Number System for Details • Pb-FREE REFLOW PROCESS COMPATIBLE SPECIFICATIONS Case Size Part Number Capacitance (*1) 0402 0603 NXED0402S15X501TRF NXED0603S15Y501TRF 0.05 ± 0.05pF 0.10 ± 0.1pF Peak Voltage (*2) 500V max. (350V typ.) Clamping Voltage (*3) Rated Voltage Leakage Current (max.) (*4) Temperature Range 100V max. 15V max. 1μA -55 ~ +125°C 1. Capacitance value shall be measured at 1MHz ±10%, 1V ± 0.2Vrms and 25 ± 2°C 2. Peak voltage shall be measured under the IEC61000-4-2, 8kV contact dischsrge ESD test conditions. 3. Clamping voltage shall be measured at 20ns after initiation of pulse and measured under IEC61000-4-2, 8kV contact dischsrge ESD test conditions 4. Leakage current shall be measured at 15Vdc. DIMENSIONS (mm) Case L W T a b Size 0402 1.00 ± 0.05 0.50 ± 0.05 0.38 ± 0.05 0.20 ± 0.1 0.25±0.1 0603 1.60 ± 0.10 0.80 ± 0.10 0.50 ± 0.10 0.30 ± 0.2 0.30±0.2 PART NUMBERING SYSTEM NXED 0603 S 15 X 501 TR F RoHS Compliant Tape & Reel Peak Voltage Capacitance Code: X = 0.05pF, Y = 0.1pF Rated Voltage: 15Vdc S = Standard Case Size L Series W a Structure Substrate Protective Coating ESD Element Inner Electrode Barrier Plating Termination Finish a T b Material AI203 Resin Composite metal powder and resin Thin metal film Nickel 100% Sn Inner electrode b ESD element Barrier Plating Termination finish Protective coating Substrate NXED APPLICATIONS ESD Protection of Data Lines ® 68 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount ESD Suppressor NXED Series RECOMMENDED LAND PATTERN DIMENSIONS (mm) TYPICAL ESD SUPPRESSION CHARACTERISTICS 400 0402 0603 300 250 Volts (V) Reflow Soldering A B C 0.5 ~ 0.6 0.40 ~ 0.55 0.4 ~ 0.6 0.7 ~ 0.9 0.55 ~ 0.75 0.8 ~ 1.0 Case Size 350 200 150 C 100 50 0 -50 B -20 0 20 40 60 80 100 120 140 160180 200 Time (nano-seconds) A B RECOMMENDED REFLOW SOLDERING TEMPERATURE PROFILE 300 10 Sec. Peak Temperature 260°C 260 230 200 180 Natural Cooling 150 100 Time above 230°C 30 ~ 40 Sec. 60 ~ 120 Sec. 50 0 CARRIER TAPE DIMENSIONS (mm) Type A B NXED0402 0.70 ±0.05 1.20 ± 0.05 NXED0603 1.10 ± 0.10 1.90 ± 0.10 φ1.5+0.1/-0.0 W F E 8.0 ± 0.2 3.50 ±0.05 1.75 ±0.10 P1 T Qty/Reel 2.00 ±0.05 0.60 ± 0.05 10,000 4.00 ± 0.05 0.70 ± 0.05 5,000 4.0 ±0.1 B F W B t P1 A C REEL DIMENSIONS (mm) A +0/-3 B ± 1.0 C min. W ± 0.3 180 13 60 9.0 W ® NIC COMPONENTS CORP. A www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 69 Surface Mount Fuse NFCC & NFHC Series FEATURES • RECTANGULAR PACKAGE WITH METAL STRIP FUSE ELEMENT • EIA SIZES 0402, 0603, 0805 AND 1206 • CURRENT RATINGS FROM 0.2 ~ 5.0 AMPS RoHS Compliant • SAFETY STANDARD APPROVAL (UL and c-UL File Number E302168) • Pb-FREE COMPATIBLE WITH FLOW AND REFLOW SOLDERING includes all homogeneous materials *See Part Number System for Details SPECIFICATIONS Type Case Size NFCC04 NFHC04 NFCC06 NFHC06 NFCC08 NFHC08 NFCC12 NFHC12 0402 0603 0805 1206 Rated Current Rated Voltage (Amps) (Vdc) 0.2 ~ 1.25 1.6 ~ 3.15 0.15 ~ 2.5 3.15 ~ 4.0 0.4 ~ 2.5 3.15 ~ 5.0 0.2 ~ 2.5 3.15 ~ 5.0 Temperature Range Case Dimensions L W H P1 P2 1.0 ± 0.05 0.5 ± 0.05 0.4 ± 0.10 0.2 ± 0.10 0.25 ± 0.10 1.6 ± 0.01 0.8 +0.15/-0.05 0.45 ± 0.10 0.3 ± 0.15 0.3 ± 0.10 50 2.0 ± 0.10 1.25 ± 0.10 0.6 ± 0.10 0.4 ± 0.20 0.4 ± 0.20 50 32 3.2 ± 0.20 1.6 ± 0.15 0.6 ± 0.10 0.65 ± 0.10 0.5 ± 0.25 0.5 ± 0.25 24 32 -55°C ~ +125°C L Fuse element (metal film) 631 Termination finish (100% Sn over Ni barrier) W Glass Overcoat Al203(96%) Substrate Glaze Layer (Glass) Top, side and bottom base termination (Ag) P1 H P2 PART NUMBERING SYSTEM NFCC 08 202 AD TP F RoHS Compliant Tape & Reel: PA = Paper (2mm pitch) TP = Paper (4mm pitch) Clearing Time Code: AD = Within 5 sec. under 250% of rated current AB = Within 5 sec. under 200% of rated current Current Rating Code: See ratings table Case Size Code: See specifications table Series ® 70 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse NFCC & NFHC Series AVAILABLE VALUES AND RATINGS Part Number NFCC04 201ADPAF NFCC04 251ADPAF NFCC04 321ADPAF NFCC04 401ADPAF NFCC04 501ADPAF NFCC04 631ADPAF NFCC04 801ADPAF NFCC04 102ADPAF NFCC04 132ADPAF NFHC04 162ADPAF NFHC04 202ADPAF NFHC04 252ADPAF NFHC04 322ADPAF NFCC06 151ADTPF NFCC06 201ADTPF NFCC06 251ADTPF NFCC06 321ADTPF NFCC06 401ADTPF NFCC06 501ADTPF NFCC06 631ADTPF NFCC06 801ADTPF NFCC06 102ADTPF NFCC06 132ADTPF NFCC06 162ADTPF NFCC06 202ADTPF NFCC06 252ADTPF NFHC06 322ADTPF NFHC06 402ADTPF NFCC08 401ADTPF NFCC08 501ADTPF NFCC08 631ADTPF NFCC08 801ADTPF NFCC08 102ADTPF NFCC08 132ADTPF NFCC08 162ADTPF NFCC08 202ADTPF NFCC08 252ADTPF NFHC08 322ADTPF NFHC08 402ADTPF NFHC08 502ADTPF NFCC12 201ADTPF NFCC12 251ADTPF NFCC12 321ADTPF NFCC12 401ADTPF NFCC12 501ADTPF NFCC12 631ADTPF NFCC12 801ADTPF NFCC12 102ADTPF NFCC12 132ADTPF NFCC12 152ADTPF NFCC12 162ADTPF NFCC12 202ADTPF NFCC12 252ADTPF NFHC12 322ADTPF NFHC12 402ADTPF NFHC12 502ADTPF Current Rating Marking Case Size @ +70°C Symbol 0402 0603 0805 1206 0.2 0.25 0.315 0.4 0.5 0.63 0.8 1.0 1.25 1.6 2.0 2.5 3.15 0.15 0.2 0.250 0.315 0.4 0.5 0.63 0.8 1.0 1.25 1.6 2.0 2.5 3.15 4.0 0.4 0.5 0.63 0.8 1.0 1.25 1.6 2.0 2.5 3.15 4.0 5.0 0.2 0.25 0.315 0.4 0.5 0.63 0.8 1.0 1.25 1.5 1.6 2.0 2.5 3.15 4.0 5.0 Z C D E F I K L M N S T U 0D ZD CD DD ED FD ID KD LD MD ND SD TD UD XD 401 501 631 801 102 132 162 202 252 UD XD YD 201 251 321 401 501 631 801 102 132 152 162 202 252 UD XD YD Time/Current Internal (Cold) Melting I2T Voltage Drop Rated Breaking Characteristics (R/C x 100) Voltage Capacity (t=1ms) Resistance (DC) (Amps) Current Pre-arc (A2×s) typical mV typical (mΩ) max. time 1000 0.0005929 199 750 0.0008464 172 620 0.00169 153 340 0.0023104 139 290 0.004305625 125 210 0.00625 121 5 sec. 24 35 250% 150 0.0119025 121 max. 120 0.0207025 114 90 0.03364 110 55 0.0442225 86 40 0.07744 86 36 0.15625 36 26 0.37636 26 4000 0.00036 521 1800 0.00081 347 1000 0.0011025 209 750 0.00169 208 330 0.0023104 126 280 0.0036864 124 5 sec. 32 35 250% 200 0.00676 126 max. 130 0.0105625 97 110 0.016 107 85 0.03249 98 70 0.064 107 55 0.13689 106 45 0.23716 109 26 0.4 88 5 sec. 24 35 250% max. 19 0.784 90 330 0.0024025 123 270 0.0033489 120 190 0.0044944 114 130 0.0093025 96 5 sec. 100 0.01444 102 50 50 250% max. 80 0.02704 99 65 0.0442225 102 55 0.09025 115 40 0.13456 110 26 0.46225 85 32 5 sec. 50 250% 19 0.841 82 max. 14 1.48225 70 24 1800 0.000570025 341 1000 0.0009216 227 750 0.0015129 213 350 0.0024025 141 295 0.0033124 115 200 0.0058564 127 5 sec. 50 50 250% 140 0.0087025 114 max. 110 0.0156025 103 85 0.02916 104 78 0.04624 101 75 0.0664225 110 65 0.1 109 45 0.18769 111 26 0.4 90 5 sec. 32 50 250% 19 0.784 84 max. 14 1.40625 83 ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 71 Surface Mount Fuse NFCC & NFHC Series AVAILABLE VALUES AND RATINGS Part Number NFCC04 251ABPAF NFCC04 321ABPAF NFCC04 401ABPAF NFCC04 501ABPAF NFCC04 631ABPAF NFCC04 751ABPAF NFCC04 801ABPAF NFCC04 102ABPAF NFCC04 132ABPAF NFCC04 152ABPAF NFCC04 162ABPAF NFHC04 202ABPAF NFHC04 252ABPAF NFCC06 251ABTPF NFCC06 321ABTPF NFCC06 401ABTPF NFCC06 501ABTPF NFCC06 631ABTPF NFCC06 751ABTPF NFCC06 801ABTPF NFCC06 102ABTPF NFCC06 132ABTPF NFCC06 152ABTPF NFCC06 162ABTPF NFCC06 202ABTPF NFCH06 252ABTPF NFCC08 501ABTPF NFCC08 631ABTPF NFCC08 801ABTPF NFCC08 102ABTPF NFCC08 132ABTPF NFCC08 162ABTPF NFCC08 202ABTPF Current Rating Marking Case Size @ +70°C Symbol 0402 0603 0805 NFHC08 252ABTPF 0.25 0.315 0.4 0.5 0.63 0.75 0.8 1.0 1.25 1.5 1.6 2.0 2.5 0.25 0.315 0.4 0.5 0.63 0.75 0.8 1.0 1.25 1.5 1.6 2.0 2.5 0.5 0.63 0.8 1.0 1.25 1.6 2.0 C D E F I A K L M H N S T CB DB EB FB IB AB KB LB MB HB NB SB TB FB IB KB LB MB NB SB 1000 750 620 340 290 220 210 150 120 100 90 55 40 1800 1000 750 330 280 210 200 130 110 95 85 70 40 330 270 190 130 100 80 65 0.0005929 0.00081 0.0016384 0.00225 0.00441 0.0055225 0.00625 0.0126025 0.0207025 0.02809 0.036 0.04624 0.07744 0.0006084 0.0010404 0.0017424 0.0024964 0.0036864 0.0054289 0.00625 0.0099225 0.0164025 0.02704 0.0330625 0.05929 0.14884 0.0024025 0.0033124 0.0047089 0.0081225 0.0133225 0.02704 0.05041 265 229 210 188 170 179 168 164 156 166 156 121 119 474 281 289 167 166 165 175 133 144 135 136 146 115 162 164 160 129 138 139 139 2.5 TB 40 0.11664 118 Current vs. Temperature Derating Guide Percentage of Rated Current Internal (Cold) Melting I2T Voltage Drop Rated Breaking (t=1ms) (R/C x 100) Voltage Capacity Resistance (A2×s) typical mV typical (DC) (Amps) (mΩ) max. 100% 80% Time/Current Characteristics Pre-arc Curent time 24 35 200% 5 sec. max. 32 35 200% 5 sec. max. 50 50 200% 5 sec. max. 32 50 200% 5 sec. max. Nominal Derating Option Code AD: < 80& of Rated Current Option Code AB: < 70% of Rated Current Example: P/N NFCC0603102AB Rated Current: 1.0A @ 70°C Derating at 90°C: Current Rating x Normal Derating x Temperature Derating at +90°C 1.0A (Rated Current) x 0.70 (Type AB) x 0.80 (Temperature Derating) = 0.56A 1.0A (Rated Current) x 0.80 (Type AD) x 0.80 (Temperature Derating) = 0.64A 0 -55°C 70°C 90°C Ambient Temperature 125°C ® 72 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse Item NFCC & NFHC Series Specification Test Method Ambient Temperature: 10°C ~ 30°C 75°C Applied Current: Rated Current No fusing Rated Current x 110% @ 70°C ± 2°C for 1 hr -55°C ~ +125°C See Available Values and Ratings Tables Rated Current x 250% Pre-acting time 5 sec. max. Test current shall be applied continuously to the fuse mounted on the test substrate Rated Current x 200% Pre-acting time 5 sec. max. JIS C0051:1994 7.4.1 No Visible Damage On the test substrate bending value is 3mm Internal Resistance Change ±3% (AD, AB) for 10 ±1 sec. JIS C0054:1994 At least 95% coverage of the terminal surface Immersion into solder at 235C ±5°C for 2 ± 0.5 secs. Immersion into solder at 260°C for 10 sec. No Visible Damage Reflow Soldering Internal resistance range ±10% max. 1. Pre-heating: 150°C ±5°C, 120 sec. max. 2. T max. 240°C ±5°C, 10 sec. max, 2 passes At normal ambient temperature & RH on the test substrate Within 10% of voltage drop Rated Current x 1.05, 1 hour "ON", 1/4 hour "OFF", 100 cycles Rated current x 1.25 for 1 hour Surface Temperature Rise Current Capability Working Temperature Range Time/Current Characteristic AD Option Code AB Bending Strenght Solderability Resistance to Soldering Heat Endurance (Load Life) RECOMMENDED REFLOW PROFILE RECOMMENDED FLOW PROFILE Note: 0402 Reflow Only Peak Temperature (245°C for 5 sec.) 250 200 150 Cool Down 100 Time above 220°C 30 sec. max. 50 Pre-heat 150°C ~ 180°C 120 sec. max. 25 300 Temperature - Deg. C Temperature - Deg. C 300 200 150 Cool Down 100 50 25 0 Peak Temperature (245°C ~ 250°C) 250 Pre-heat 110°C ~ 130°C 120 sec. max. 0 Time Time Recommended Land Pattern Dimensions (mm) Reflow Soldering Flow Soldering Case Size A B C D A B C D 0402 0.5 1.3 0.5 0.4 N/A 0603 1.0 2.0 0.8 0.5 1.0 2.6 0.8 0.8 0805 1.3 2.7 1.25 0.7 1.3 3.1 1.25 0.9 1206 2.2 3.9 1.6 0.85 2.2 4.3 1.6 1.05 C D A D B ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 73 Surface Mount Fuse NFCC & NFHC Series FUSING TIME CURRENT CHARACTERISTICS ® 74 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse NFCC & NFHC Series FUSING TIME CURRENT CHARACTERISTICS ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 75 Surface Mount Fuse NFCC & NFHC Series FUSING TIME CURRENT CHARACTERISTICS ® 76 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse NFCC & NFHC Series FUSING TIME CURRENT CHARACTERISTICS ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 77 Surface Mount Fuse NFCC & NFHC Series CARRIER TAPE DIMENSIONS (mm) Type A B W F E P1 P0 φD T1 T2 Qty/Reel NFCC04NFHC04 0.65 ±0.10 1.15 ±0.10 8.00 ±0.20 3.50 ±0.05 1.75 ±0.10 2.00 ±0.05 4.00 ±0.05 1.55 ±0.05 0.60 ±0.05 0.70 max. 10,000 Qty/Reel φ1.5+0.1/-0.0 4.0 ±0.1 t1 F W B t2 P1 A CARRIER TAPE DIMENSIONS (mm) Type A B NFCC06/NFHC06 1.15 ±0.15 1.90 ±0.20 NFCC08/NFHC08 1.65 ±0.15 2.50 ±0.20 NFCC12/NFHC12 2.00 ±0.15 3.6 ± 0.20 W F E P1 P0 φD T1 T2 8.00 ±0.20 3.50 ±0.05 1.75 ±0.10 4.00 ±0.05 4.00 ±0.05 1.55 ±0.05 0.7 max. 0.8 max. 0.9 max. 1.0 max. φ1.5+0.1/-0.0 5,000 4.0 ±0.1 t1 F W B t2 A P1 REEL DIMENSIONS (mm) AND QUANTITY Type A +0/-3 B +1/-0 C ±0.20 W ±0.3 NFCC04/NFHC04 NFCC06/NFHC06 NFCC08/NFHC08 Qty 10,000 180 60 13 9.0 5,000 E NFCC12/NFHC12 C B D W ® 78 NIC COMPONENTS CORP. A www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse NFSC Series FEATURES • HIGH ANTI-PULSE PERFORMANCE • EIA SIZE 0603 • CURRENT RATINGS UP TO 5.0 AMPS • SAFETY STANDARD APPROVAL (UL and c-UL File Number E302168) • Pb-FREE COMPATIBLE WITH FLOW AND REFLOW SOLDERING RoHS Compliant includes all homogeneous materials *See Part Number System for Details SPECIFICATIONS Type Case Size NFSC06 0603 Rated Current Rated Voltage (Amps) (Vdc) 0.5 ~ 5.0 32 Temperature Range Case Dimensions L H P1 P2 0.45 ± 0.10 0.3 ± 0.15 0.3 ± 0.10 W -55°C ~ +125°C 1.6 ± 0.01 0.8 +0.15/-0.05 L Fuse element (metal film) Resin Overcoat Side termination (Thin film of Ni-Cr) S Termination finish (100% Sn over Ni barrier) W Al203(96%) Substrate Resin Layer Bottom termination (Ag) P1 H P2 PART NUMBERING SYSTEM NFSC 06 202 AB TP F RoHS Compliant Tape & Reel: TP = Paper (4mm pitch) Clearing Time Code: AB = Within 5 sec. under 200% of rated current Current Rating Code: See ratings table Case Size Code: See specifications table Series ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 79 Surface Mount Fuse NFSC Series AVAILABLE VALUES AND RATINGS Part Number NFSC06 501ABTPF NFSC06 631ABTPF NFSC06 751ABTPF NFSC06 801ABTPF NFSC06 102ABTPF NFSC06 132ABTPF NFSC06 162ABTPF NFSC06 202ABTPF NFSC06 252ABTPF NFSC06 302ABTPF NFSC06 322ABTPF NFSC06 402ABTPF NFSC06 502ABTPF Current Marking Rating Symbol @ +70°C 0.5 F 0.63 I 0.75 A 0.8 K 1.0 L 1.25 M 1.6 N 2.0 S 2.5 T 3.0 R 3.15 U 4.0 X 5.0 Y Internal (Cold) Resistance (mΩ) max. 400 300 210 180 115 90 60 50 37 28 26 18 14 Voltage Drop Rated Melting I2T (t=1ms) (R/C x 100) Voltage (A2×s) typical mV typical (DC) 0.00529 182 0.01156 153 0.0189225 150 0.02116 138 0.03025 116 0.06084 114 32 0.11025 96 0.169 92 0.256 84 0.35721 75 0.38025 76 0.53824 70 1.089 68 Breaking Capacity (Amps) Time/Current Characteristics Curent/Pre-arc time x100% / 4 hrs. x200% / 5 sec. x300%/ 0.2 sec. 35 Current vs. Temperature Derating Guide Percentage of Rated Current 120% Nominal Derating: < 75% of Rated Current 100% 80% Temperature Derating: Refer to graph 60% Example: NFSC0603102AB (1A rated current) If used at +70°C the derated current would be ... 1A x 0.75 (normal derating) x 0.80 (temperature derating) = 0.6A 40% 20% 0 -55°C 125°C 70°C 90°C Ambient Temperature RECOMMENDED FLOW PROFILE RECOMMENDED REFLOW PROFILE Temperature - Deg. C Peak Temperature (245°C for 5 sec.) 250 200 150 Cool Down 100 Time above 220°C 30 sec. max. 50 Pre-heat 150°C ~ 180°C 120 sec. max. 25 Temperature - Deg. C 300 300 Peak Temperature (245°C ~ 250°C) 250 200 150 Cool Down 100 50 25 Pre-heat 110°C ~ 130°C 120 sec. max. 0 0 Time Time Recommended Land Pattern Dimensions (mm) Reflow Soldering Flow Soldering Case Size A B C D A B C D 0603 1.0 2.0 0.8 0.5 1.0 2.6 0.8 0.8 C D ® 80 NIC COMPONENTS CORP. A D B www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Surface Mount Fuse NFSC Series CARRIER TAPE DIMENSIONS (mm) Type NFSC06 A 1.15 ±0.15 B W F E 1.90 ±0.20 8.00 ±0.20 3.50 ±0.05 1.75 ±0.10 φ1.5+0.1/-0.0 P1 P0 φD T1 T2 Qty/Reel 4.00 ±0.05 4.00 ±0.05 1.55 ±0.05 0.7 max. 0.8 max. 5,000 4.0 ±0.1 t1 F W B t2 A P1 REEL DIMENSIONS (mm) AND QUANTITY Type A +0/-3 B +1/-0 C ±0.20 W ±0.3 Qty NFSC06 180 60 13 9.0 5,000 E C B D W A ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 81 Carbon Film Resistors NCF Series FEATURES • ECONOMICALLY PRICED FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS • WIDE SELECTION OF POWER RATINGS AND RESISTANCE VALUES • EIA COLOR CODING RESISTANT TO INDUSTRIAL SOLVENTS • AVAILABLE ON TAPE AND REEL FOR AUTOMATIC INSERTION AND BULK PACK FOR SMALLER PRODUCTION RUNS RoHS • NEW REDUCED SIZES AT HIGHER POWER RATINGS Compliant includes all homogeneous materials • ±5% TOLERANCE STANDARD STANDARD TYPES, RATINGS AND AVAILABILITY *See Part Number System for Details Type NCF25R NCF25 NCF50 NCF50R NCF100 NCF200 Power Rating at 70°C 0.25W 0.25W 0.50W 0.50W 1.0W 2.0W Max. Working Voltage at 70°C 250V 250V 350V 350V 500V 750V Max. Overload Voltage at 70°C 500V 500V 700V 700V 1000V 1500V Resistance Range ±5% (J) Tol. 1.0Ω~10MegΩ 0.5Ω~10MegΩ 1.0Ω~10MegΩ 1.0Ω~10MegΩ 1.0Ω~10MegΩ 1.0Ω~10MegΩ Resistance Value Availability E-24 E-24 E-24 E-24 E-24 E-24 PERFORMANCE CHARACTERISTICS Requirements Performance Test Method & Conditions Operating Temperature Range -55 ~ +155°C (derated above +70°C - see chart) JIS C5202 MIL-R-10509F (ppm/°C) 0.25W & Over NCF25R 0 ~ -450 <22KΩ <100KΩ Temperature 5.2 0 ~ -700 110KΩ ~ 1megΩ 24KΩ ~ 470KΩ Coefficient 4.6.12 1- to = 80°C (ppm/°C) 0 ~ -1000 1.1megΩ ~ 2.2megΩ 510KΩ ~ 2.2megΩ 0 ~ -1300 2.4megΩ ~ 10megΩ 2.2megΩ ~ 10megΩ (NCF25R) 0.25W & Over (μV/V) 0.1 0.5Ω ~ 10KΩ JIS C5202 5.9 0.3 Noise (μV/V) 1.0Ω ~ 10KΩ 11Ω ~ 91KΩ Method II 0.5 11Ω ~ 91KΩ 100KΩ ~ 1megΩ 1.0 100KΩ ~ 10megΩ 1.1megΩ ~ 10megΩ 5.5 Cond. A 4.6.6 Short Time Overload ΔR < ±(1%+0.05Ω) 7.4-55°C/+85°C 4.6.4 Temperature Cycling ΔR < ±(0.5%+0.05Ω) 6.4 350°C 3 sec. 4.6.10 Soldering Effect ΔR < ±(1%+0.05Ω) 6.3 Cond. A 4.6.16 Vibration ΔR < ±(0.5%+0.05Ω) R > 100K ΔR < ±5% Moisture 7.9 40°C 4.6.11 Resistance 90-95%RH 1000hrs R < 100K ΔR < ± (3%+0.05Ω) 7.10 R > 100K ΔR < ± 3% 4.6.13 Load Life 70°C 1000hrs R < 100k ΔR < ±(3%+0.05Ω) * Maximum allowable continuous voltage (Vdc or rms) for all resistors is the lower of the two values: “MAXIMUM WORKING VOLTAGE” as specified, or Power rating (WATTS x Resistance (OHMS) Derating Curve 70oC PERCENTAGE RATED LOAD 100 80 50 40 20 0 20 40 60 80 100 120 140 ↑160 180 155 AMBIENT TEMPERATURE (oC) ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 69 Carbon Film Resistors NCF Series DIMENSIONS (mm) Type NCF25R NCF25 NCF50 NCF50R NCF100 NCF200 Dφ 1.8 ± 0.2 2.5 ± 0.5 3.5 ± 0.5 2.3 ± 0.5 4.5 ± 0.5 5.5 ± 0.5 L 3.3 ± 0.4 6.3 ± 0.5 9.0 ± 0.5 6.5 ± 0.5 11.0 ± 0.5 15.0 ± 0.5 dφ ± 0.05 0.45 0.56 0.65 0.56 0.80 0.80 d∅ Black Brown Red Orange Yellow Green Blue Violet Grey White Gold Silver D∅ 25 Min. SIGNIFICANT VALUES OF NOMINAL RESISTANCE E-24 5% (J) COLOR CODING Color L 25 Min. Significant Figure 1st 2nd 3rd 0 0 0 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 - Multiplier 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 Tolerance 1 10 F (±1%) 100 G (±2%) 1,000 10,000 100,00 D ±0.5%) 1,000,000 C (±0.25%) 10,000,000 B (±0.1%) 0.1 J (±5%) 0.01 K (±10%) 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 PART NUMBER SYSTEM NCF 25 J 103 TR F RoHS compliant parts TR = Tape and Reel Resistance Code: First 2 digits are significant, 3rd digit is multiplier, “R” indicates decimal on values below 10 OHMS Tolerance Code: G = ±2% (Opt.) J = ±5% STD. CARBON FILM Power Rating (Wattage Code) 25 = .25W 50 = .50W 25R = .25W 50R = .50W Series 100 = 1 WATT 200 = 2WATT PACKAGING & REEL QUANTITIES Tape and Reel - 5K NCF25R, 25 and 50R 2.5K NCF50 2K NCF100 1K for NCF200 Zero-Ohm Resistors NZO Series FEATURES • STANDARD 1/8 WATT AND 1/4 WATT SIZES • FOR JUMPERS OR CROSSOVERS ON PCB’S • TAPE AND REEL FOR AUTOMATIC INSERTION • SINGLE BLACK BAND INDICATES ZERO RESISTANCE SPECIFICATIONS OPERATING TEMPERATURE RANGE: –55OC to +155OC RESISTANCE: 0.01 OHM or less CURRENT RATING: 2.5 AMPS (–55OC to +70OC) DERATED GRAPH BELOW d∅ 25 Min. ZERO OHM RESISTORS CURRENT RATING OVER TEMPERATURE NZO25R & NZO25 PARTS. L D∅ 25 Min. DIMENSIONS (mm) Type NZO25R NZO25 Dφ 1.8 ± 0.1 2.3 ± 0.2 L 3.2 ± 0.2 6.5 ± 0.5 dφ ± 0.05 0.5 0.6 2.5AMP 2.0AMP PART NUMBER SYSTEM 1.5AMP NZO 25 TR F RoHS compliant TR = Tape and Reel 1.0AMP Size: 25R = 1/8W Size 25 = 1/4W Size 0.5AMP 0 ® 70 -55OC -25OC O 0OC +25OC +50OC +75OC +100OC+125OC +155 C NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com Series www.RFpassives.com www.SMTmagnetics.com Metal Film Resistors NMR Series FEATURES • MEETS OR EXCEEDS MIL-R-10509E SPECIFICATIONS • ULTRA-LOW NOISE WITH LOW TEMPERATURE COEFFICIENTS • CLOSE TOLERANCE, PRECISION APPLICATIONS • EIA COLOR CODING RESISTANT TO INDUSTRIAL SOLVENTS • AVAILABLE ON TAPE AND REEL FOR AUTOMATIC INSERTION AND ..BULK PACK FOR SMALL PRODUCTION RUNS OR PROTOTYPES • ECONOMICALLY PRICED RoHS Compliant includes all homogeneous materials *See Part Number System for Details STANDARD TYPES, RATINGS AND AVAILABILITY Type Power Rating at 70°C Max. Working Voltge at 70°C Max. Overload Voltage at 70°C Resistance Tolerance ±50ppm/°C Temperature Coefficient ±100ppm/°C Resistance Value Availability NMR16 0.125W 150V 300V F ±1% (Std.) 10Ω ~ 1MegΩ Less than10Ω More than 1MegΩ E-96 NMR25 0.25W 250V 500V (D) ±0.5% (Opt.) (F) ±1% (Std) 10Ω ~ 1MegΩ Less than10Ω More than 1MegΩ E-96 NMR50 0.5W 350V 700V (F) ±1% (Std) 10Ω ~ 1MegΩ Less than10Ω More than 1MegΩ E-96 NMR100 1W 500V 1000V (F) ±1% (Std) -*10Ω ~ 1MegΩ E-96 * Extended resistance range available on request PERFORMANCE CHARACTERISTICS Requirements Operating Temperature Range Temperature Coefficient Temperature Cycling Low Temperature Operation Short Time Overload Terminal Strength Dielectric Withstanding Voltage Insulation Resistance Soldering Effect Moisture Resistance Load Life Vibration Current Noise Solvent Resistance Test Method MIL-R-10509F -55 ~ +155°C ±50ppm, ±100ppm/°C 4.6.12 4.6.6 R < ±(0.5% + 0.05Ω) 4.6.5 R < ±(0.5% + 0.05Ω) 4.6.6 R < ±(0.5% + 0.05Ω) 4.6.7 R < ±(0.5% + 0.05Ω) 4.6.8 R < ±(0.5% + 0.05Ω) 4.6.9 10,000MΩ minimum 4.6.10 R < ±(0.5% + 0.05Ω) (MIL-R_22684B, 4.6.10) R < ±(1% + 0.05Ω) 4.6.13 R < ±(1% + 0.05Ω) (MIL-R_22684B, 4.6.16) R < ±(0.5% + 0.05Ω) (JIS C5202, 5.9 Method II) 0.2μV/V (-14dB) MIL-STD-202, Method 215, Tricholorethylene, Tricholorethane, Trichlorotrifluroroethane Performance **- Maximum allowable continuous voltage (Vdc or rms) for all resistors is the lower of the two values: “MAXIMUM WORKING VOLTAGE” as specified or Power rating (WATTS x Value (Ω) TYPICAL PERFORMANCES DERATING CURVE SURFACE TEMPERATURE (OC) PERCENT RATED WATTAGE (%) 100 80 60 40 20 0 0 40 SURFACE TEMPERATURE RISE 100 80 NMR100 NMR50 60 40 NMR25 20 70 100 120 140 155 180 TEMPERATURE (°C) 0 20 40 60 80 100 PERCENT RATED WATTAGE (%) ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 71 Metal Film Resistors NMR Series DIMENSIONS (mm) Type NMR16 NMR25 NMR50 NMR100 Dφ 1.7 ± 0.2 2.4 ± 0.4 3.2 ± 0.5 4.5 ± 0.5 L 3.7 ± 0.4 6.4 ± 0.5 9.5 ± 0.5 11.0 ± 1.0 dφ ± 0.05 0.45 0.60 0.65 0.80 d∅ 25 Min. L 25 Min. D∅ COLOR CODING Color Black Brown Red Orange Yellow Green Blue Violet Grey White Gold Silver Significant Figure 1st 2nd 3rd 0 0 0 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 - Multiplier Significant Figures of Nominal Resistance Values (E-96 1% Tolerance) 1.00 1.02 1.05 1.07 1.10 1.13 1.15 1.18 1.21 1.24 1.27 1.30 1.33 1.37 1.40 1.43 1.47 1.50 1.54 1.58 1.62 1.65 1.69 1.74 1.78 1.82 1.87 1.91 1.96 2.00 2.05 2.10 2.15 2.21 2.26 2.32 2.37 2.43 2.49 2.55 2.61 2.67 2.74 2.80 2.87 2.94 3.01 3.09 3.16 3.24 3.32 3.40 3.48 3.57 3.65 3.74 3.83 3.92 4.02 4.12 4.22 4.32 4.42 4.53 4.64 4.75 4.87 4.99 5.11 5.23 5.36 5.49 5.62 5.76 5.90 6.04 6.19 6.34 6.49 6.65 6.81 6.98 7.15 7.32 7.50 7.68 7.87 8.06 8.25 8.45 8.66 8.87 9.09 9.31 9.53 9.76 Tolerance 1 10 F (±1%) 100 G (±2%) 1,000 10,000 100,00 D ±0.5%) 1,000,000 C (±0.25%) 10,000,000 B (±0.1%) 0.1 J (±5%) 0.01 K (±10%) METAL FILM PART NUMBER SYSTEM NMR 25 F 1003 TR F RoHS compliant parts TR = Tape and Reel Resistance code: First 3 digits are significant, 4th digit is multiplier. Use “R” as decimal for values below 100 OHMS. Tolerance Code: F = ±1% (STD.) G = ±2% (OPT.) D = ±0.5% (OPT.) PACKAGING & REEL QUANTITIES Tape and Reel - 5K NMR16 and 25 2.5K NMR50 2K NMR100 Power Ratings (Wattage Code) 16 = .125W 50 = .50W Series 25 = .25W 100 = 1 WATT ® 72 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Metal Oxide Film Resistors NMO Series FEATURES • NON-FLAMMABLE RESIN INSULATION • HIGH STABILITY AND RELIABILITY • LOW NOISE • LOW COST ALTERNATIVE TO CARBON COMPOSITION AND ..WIREWOUND APPLICATIONS • NEW REDUCED SIZES • EIA COLOR CODING AND ALPHA-NUMERICAL CODING ..AVAILABLE DEPENDING ON SIZE RoHS Compliant includes all homogeneous materials *See Part Number System for Details STANDARD TYPES, RATINGS AND AVAILABILITY Type Power Rating at 70°C Max. Working Voltage at 70°C** Max. Overload Voltage at 70°C Max. Pulse Voltage at 70°C ±5% (J) Tol. Resistance Range ±2% (G) Tol. Resistance Value Availability Axial Taping Availability NMO100 1 Watt 350V 600V 750V 0.22Ω ~ 100KΩ 10Ω ~ 100KΩ E-24 Yes NMO200 2 Watts 350V 600V 750V 0.22Ω ~ 100KΩ 10Ω ~ 100KΩ E-24 Yes NMO300 3 Watts 500V 800V 1500V 0.5Ω ~ 100KΩ 10Ω ~ 100KΩ E-24 No NMO500 5 Watts 750V 1000V 2000V 5.1Ω ~ 240KΩ 10Ω ~ 100KΩ E-24 No NMO700 7 Watts 850V 1500V 2000V 5.1Ω ~ 240KΩ 10Ω ~ 100KΩ E-24 No NMO300S 3 Watts 350V 600V 750V 0.22Ω ~ 50KΩ 10Ω ~ 50KΩ E-24 No NMO500S 5 Watts 500V 800V 750V 0.5Ω ~ 100KΩ 10Ω ~ 100KΩ E-24 No NMO700S 7 Watts 750V 1000V 1200V 10Ω ~ 200KΩ 10Ω ~ 200KΩ E-24 No REDUCED SIZE, RATING AND AVAILABILITY Type Power Rating at 70°C Max. Working Voltage at 70°C** Max. Overload Voltage at 70°C Max. Pulse Voltage at 70°C ±5% (J) Tol. Resistance Range ±2% (G) Tol. Resistance Value Availability Axial Taping Availability NMO100S 1 Watt 350V 600V 750V 0.22Ω ~ 50KΩ 10Ω ~ 50KΩ E-24 Yes NMO200S 2 Watts 350V 600V 750V 0.22Ω ~ 50KΩ 10Ω ~ 50KΩ E-24 Yes * Special Order **- Maximum allowable continuous voltage (Vdc or rms) for all resistors is the lower of the two values: “MAXIMUM WORKING VOLTAGE” as specified, or Power rating (WATTS x Resistance (OHMS) CHARACTERISTICS Test Method & Conditions JIS C5202 MIL-R-22684B -55 ~ +200°C (Derated above 70°C as per derating curve below) See Maximum Working Voltage ±200ppm/°C 5.2, t-to=80°C 4.6.11 5.5, Cond. A 4.6.5 ΔR < ±(0.5% + 0.05Ω) 7.4, -55/+85°C 4.6.3 ΔR < ±(0.5% + 0.05Ω) 6.4, +350°C for 3 sec. 4.6.9 ΔR < ±(0.5% + 0.05Ω) 6.3, Cond. A 4.6.14 ΔR < ±(0.5% + 0.05Ω) 7.9, +40°C 90~95%RH 100hrs 4.6.10 ΔR < ±5% 7.10, +70°C 1000hrs. 4.6.12 ΔR < ±5% Requirements Performance Operating Temperature Range Withstanding Voltage (Lead to Body) Temperature Coefficient Short Time Overload Temperature Cycling Soldering Effect Vibration Moisture Resistance Load Life 80 1000 60 100 40 20 0 0 40 70-80 120 160 NMO-300 NMO-200 NM0-100 10 200 10μs 100μs 1ms 10ms 100ms 1s TEMPERATURE (oC) TEMPERATURE RISE (BODY SURFACE) 250 200 NMO-300 150 NMO-200 100 NM0-100 50 0 0 CONTINUOUS TIME OF PULSE ® NIC COMPONENTS CORP. TEMPERATURE RISE (OC) PULSE WITHSTANDING POWER (ONE PULSE) DERATING CURVE 100 PULSE WITHSTANDING POWER (W) PERCENT RATED WATTAGE (%) TYPICAL PERFORMANCE www.niccomp.com www.lowESR.com www.RFpassives.com 25 50 75 100 PERCENT RATED WATTAGE (%) www.SMTmagnetics.com 73 Metal Oxide Film Resistors NMO Series DIMENSIONS (mm) Lead Material: 10% Pb, 90% Sb d∅ H D∅ Type NMO100 NMO200 NMO300 NMO500 NMO700 Type NMO100S NMO200S NMO300S NMO500S NMO700S Dφ 4.5 5.5 8.5 8.5 8.5 Dimensions (mm) L ± 1.0 H ± 3.0 11 30 15 30 24 38 41 38 53 38 dφ± 0.05 0.80 0.80 0.80 0.80 0.80 Dφ 3.5 4.5 5.5 8.5 8.5 Dimensions (mm) L ± 1.0 H ± 3.0 9.0 30 11 30 15 30 24 38 41 38 dφ± 0.05 0.65 0.80 0.80 0.80 0.80 SIGNIFICANT VALUES OF NOMINAL RESISTANCE E-24 5% (J) COLOR CODING Color Black Brown Red Orange Yellow Green Blue Violet Grey White Gold Silver H L Significant Figure 1st 2nd 3rd 0 0 0 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 - Multiplier Tolerance 1 10 F (±1%) 100 G (±2%) 1,000 10,000 100,00 D ±0.5%) 1,000,000 C (±0.25%) 10,000,000 B (±0.1%) 0.1 J (±5%) 0.01 K (±10%) 1.0 1.1 1.2 1.3 1.5 1.6 1.8 2.0 METAL OXIDE 1W, 2W, AND 3W OPTION 2.2 2.4 2.7 3.0 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 PART NUMBER SYSTEM NMO 100 S J 103 TR F RoHS compliant parts TR = Tape and Reel B = Bulk Resistance Code: First 2 digits are significant, 3rd digit is multiplier, “R” indicates decimal on values below 10 OHMS Tolerance Code: G = ±2% (Opt.) J = ±5% STD. MARKING (FOR 3WATT AND UP) S = Reduced Size Power Rating (Wattage Code) 100 = 1WATT 500 = 5WATTS 200 = 2WATTS 700 = 7 WATTS 300 = 3WATTS NMO 5W 1KΩJ Series ® 74 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Resistance Value Codes Current Sensing Resistors Conversion Table: Milli-ohm / Ohm / 4-digit code Precision Resistors E96 Values 10 14.7 21.5 31.6 46.4 68.1 Milli-ohm Ohm 4-digit code Milli-ohm Ohm 4-digit code 10.2 15 22.1 32.4 47.5 69.8 1 0.001 R001 26 0.026 R026 71.5 2 0.002 R002 27 0.027 R027 0.003 R003 28 0.028 R028 10.5 15.4 22.6 33.2 48.7 10.7 15.8 23.2 34 49.9 73.2 3 11 16.2 23.7 34.8 51.1 75 4 0.004 R004 29 0.029 R029 5 0.005 R005 30 0.030 R030 6 0.006 R006 31 0.031 R031 7 0.007 R007 32 0.032 R032 8 0.008 R008 33 0.033 R033 9 0.009 R009 34 0.034 R034 10 0.010 R010 35 0.035 R035 11 0.011 R011 36 0.036 R036 11.3 16.5 24.3 35.7 52.3 76.8 11.5 16.9 24.9 36.5 53.6 78.7 11.8 17.4 25.5 37.4 54.9 80.6 12.1 17.8 26.1 38.3 56.2 82.5 12.4 18.2 26.7 39.2 57.6 84.5 12.7 18.7 27.4 40.2 59 86.6 13 19.1 28 41.2 60.4 88.7 12 0.012 R012 37 0.037 R037 13.3 19.6 28.7 42.2 61.9 90.9 13 0.013 R013 38 0.038 R038 13.7 20 29.4 43.2 63.4 93.1 14 0.014 R014 39 0.039 R039 14 20.5 30.1 44.2 64.9 95.3 15 0.015 R015 40 0.040 R040 14.3 21 30.9 45.3 66.5 97.6 16 0.016 R016 41 0.041 R041 17 0.017 R017 42 0.042 R042 18 0.018 R018 43 0.043 R043 19 0.019 R019 44 0.044 R044 20 0.020 R020 45 0.045 R045 Precision Resistors E24 Values 10 22 47 21 0.021 R021 46 0.046 R046 11 24 51 22 0.022 R022 47 0.047 R047 12 27 56 23 0.023 R023 48 0.048 R048 13 30 62 24 0.024 R024 49 0.049 R049 15 33 68 25 0.025 R025 50 0.050 R050 16 36 75 18 39 82 20 43 91 Precision Resistors E12 Values 10 33 12 39 15 47 18 56 22 68 27 82 ® 68 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com NRC Series Temperature Rise Characteristics Typical Surface Temperature Rise NRC Series Resistors 0402 ~ 2512 Case Sizes ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 67 NRC Series Pulse Power Characteristics NRC Series - Thick Film Chip Resistors (Resistance Value: 1KΩ, Single Pulse) Pulse Width Resistance Value Influence on Pulsed Power Characterisitc of 0805 Size (1/8W) NRC10 (Pulse Width: 1mS) Resistance Value (Ω) ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 65 NRC Series Pulse Power Characteristics ® 66 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Resistor Taping Specifications & Mechanical Characteristics TAPE DIMENSIONS (mm) TAPE B D Power Rating (Wattage) A B C D max. E max. 1/8W 52 ± 1.0 5 ± 0.5 6 ± 0.3 0.6 1.2 1/4W 1/2W 52 ± 1.0 52 ± 1.0 52.4 ± 1.5 63.5 ± 1.5 52.4 ± 1.5 63.5 ± 1.5 5 ± 0.5 5 ± 0.5 6 ± 0.3 6 ± 0.3 0.6 0.6 1.2 1.2 5 ± 0.6 6 ± 0.3 0.6 1.2 5 ± 0.6 10 ± 1.0 6 ± 0.3 0.6 1.2 1W E A 2W REEL DIMENSIONS (mm) C Power Rating A max. B C ref. D max. E max F ± 1.0 1/8W ~ 2W 40 ~ 100 15 60 16 312 53 3W 70 ± 10 14.5 REEL A D F Arbor Hole Dia. Label E Hub Recess I.D. C Recess Depth B MECHANICAL CHARACTERISTICS LEAD PULL TEST The lead wire shall withstand steady pull of the following weight axially to the lead wire for the minimum period of 10 seconds without any breakage or damage: Nom. Lead Diameter Steady Weight 0.4φmm 1.0Kgs. 0.5φmm 1.0Kgs. 0.6φmm 1.5Kgs 0.7φmm 2.0Kgs. 0.8φmm & over 2.5Kgs. LEAD BEND TEST The lead wire shall withstand minimum 4 bends of 90o rotation without any breakage or damage, when the resistor is placed in a vertical position and is applied with a weight of 0.5Kgs for 0.4 - 0.5omm or 1.1Kgs for 0.6omm and over lead wire. SOLDERABILITY The lead wire is immersed into 10% methanol or isopropyl alcohol of rosin by weight for a period of 2 ± 0.5 seconds. Then, it shall be dipped into molten solder melted at 230 ± 5oC for a period of 5 ± 1 seconds approximately 1.5mm from the body of the resistor. A new adhering coating of solder shall cover minimum 95% of the surface being dipped into solder. RESISTANCE TO CLEANING SOLVENTS Color coating or marking shall remain legible after cleaning by solvents such as isopropyl alcohol, trichloroethylene, freon® TF/TAX, xyliene etc., in form of liquid or gas. ® NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com 75 Surface Mount Fuse Users Guide Fuse Function: Fuses are components design to provide circuit protection against overcurrents and short circuits. Typically a fuse consist of a conductive element that will melt when current in excess of the specified current rating and/or duration are exceeded. The melting of the conductive element shuts off current to the circuit. Fuses are not only rated by the amount of current that will cause the fuse element to melt but also based on how quickly that melting occurs and a maximum rated voltage that will avoid a catastrophic opening (explosion) of the fuse. Fuse Characteristics: Rated Current ( without fusing. ) - the current (x110% of amount specified) that can be applied to the component continuously (considered 1 hour) at +70°C Internal Cold Resistance ( ) - the typical maximum DC resistance measured when <10% of the rated current is applied to the fuse while at room temperature. I2t, Melting Integral or Clearing Time ( ) - a measurement of the energy (Joules) necessary to melt the fuse element. This value is arrived at by multiplying amperes2 by time in seconds. It represents the amount of energy to melt the fuse element. A fuse should be selected that will prohibit energy sufficient to damage the circuit from being passed down line of the fuse. Typical Voltage Drop ( ) - the typical voltage drop across the fuse measured at 100% of the rated current at room temperature. This value changes depending on the applied current. Rated Voltage ( )- the maximum voltage at which the fuse can safely interrupt an overcurrent or short-circuit condition should occur. Breaking Capacity or Interrupt Rating ( ) - the maximum overload current the fuse can safely interrupt. Exceeding the breaking capacity of the fuse can result in a catastrophic opening of the fuse. Time-Current Characteristics ( ) - the time-current characteristics give an indication as to the time it takes to melt the fuse element when a given current is applied. The higher the current the shorter the time required to cause the fuse element to melt. The time-current graph below indicates that the NFCC08 501AD part with a current rating of 0.5A will fuse almost instantly if a 1.5A current is applied. If the applied current is reduced to 1.0A the time required for the fuse to blow increases to 0.02 seconds and at 0.85A the time increases to over 100 seconds. Surface Temperature Rise ( ) - the maximum temperature increase at the surface of the component when the rated current is applied at room temperature (+10°C ~ +30°C). ( ) - The higher the better ( ) - The lower the better ( ) - Must be determined by the customer ® 64 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com Cross Reference Guide Surface Mount and Leaded Resistors NIC Series NCF Bourns Cytech Dale IRC Kamaya KOA Rhopoint Rohm SEI Yageo *** *** CFA CF *** *** *** *** *** *** R CF CFR NCSP *** *** WSC WSM *** *** *** *** *** *** *** *** *** NCSW *** *** *** *** *** CF SL TSL *** *** *** *** *** *** *** *** RL3264 WSK CSS *** TLR *** *** *** *** PMR100 *** *** NCST NCT NFA NMR *** *** WSL *** RLC SR73 SR *** LVC *** ERJ-L ERJM1W ERJ-LO RL NCSR *** *** *** *** *** *** NTHS *** *** *** *** NCP *** ERTJ *** *** *** *** *** *** EXA04S *** RAC101A *** *** *** *** EXB24AT *** *** *** *** *** *** CCF *** MF *** *** *** *** *** CRB RN MFR NMO *** *** *** GP MO MOM *** MO *** *** *** *** *** CRH RSM RSF NRC CR *** CRCW CHF RMC *** *** *** ERJ *** MCR RMC NRSNA4I2 NRSNA4I4 *** *** CRA04S04 *** *** *** *** NRSNA6I4 CAY16 *** NRSNO6I4 CAT16 *** NRSNO6C8 *** NRSNO6D8 *** NRSN12I4 *** CRA04S08 CRA06E CRA06P CRA06S *** *** *** *** *** Surface Mount Varistors NIC Series Amotech Micro-ohm Murata Ohmite Panasonic RAC102D...C RM73 RK73 *** *** *** *** EXB24V *** MNR02 *** RC RGC *** RAC104D...C CN1E4 *** *** *** EXB28V *** MNR04 *** YC12 *** RAC164D...B *** *** *** *** EXB38V *** NMR14 *** YC16 *** RAC164D...C CN1J4 *** *** *** EXBV8V *** *** *** *** *** *** CND2B10V *** *** *** EXBA10E *** MNR35 *** YC35 *** *** RAC 8U *** *** *** *** EXBA10P *** *** *** YC15 *** *** *** CN2B4J *** *** *** *** *** NMR34 *** YC32 AVX EPCOS ICT Littlefuse Panasonic TDK NVS *** VC *** *** AVL VC V_ _MLA V _ _ _ _MHS V_ _ MLA V _ _MLE *** NVT *** CM CN NC EZJZ AVR AVR-M Surface Mount Fuses NIC Series AVX NFHC F_ _ _ _B F_ _ _ _C F_ _ _ _E F_ _ _ _FA F0612 NFSC *** NFCC BEL Bussman ICVN Daito KOA C1Q C2Q _ _ _ _FA _ _ _ _FF KMD KE *** *** *** TF_ _AN TF_ _AT TF_ _SN CCP2B CCP2E *** PC06F *** TF_ _AT Littlefuse Matsuo Pansonic Skygate TA-I *** JAA ERBSD ERBSE _ _ _ _FA *** *** 431 434 467 494 JAD *** *** *** KAB_ _ _29010 *** *** CF06V Note: Crosses may not be exact for all characteristics. Please consult the datasheet for detailed specifications. (For additional cross reference information see our website cross reference search engine at: www.niccomp.com) T4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com