TTG-Series Rocker Switches The TTG-Series Mini Tippette snap-in rocker switches consist of two single pole illuminated or non-illuminated switches in a common base. Each pole can have the same or different switch function. These switches are AC rated up to 20 amps and are also suitable for low-voltage DC applications, in a wide range of markets including Appliance, HVAC, Food service and Transportation. Carling Technologies, Inc. 60 Johnson Avenue • Plainville, CT 06062-1177 Phone: (860) 793-9281 • Fax: (860) 793-9231 Email: [email protected] • www.carlingtech.com 2 | TTG-Series Rocker Switches Dielectric Strength Mechanical Life UL/CSA: 1000V - live to dead metal parts 100,000 cycles Operating Temperature Electrical Life 32°F to 185°F (0°C to 85°C) 50,000 cycles - maintained 25,000 cycles - momentary TTG T 1 Base Part Number 2 Circuit TA 20 1 LTA 20 1 3 Center Position 4 Rating T B P B 5 Termination 6 Actuator Style 7 Actuator Color B B R / 125N 8 Base Color 9 Lens Color 10 Lamp Voltage 1 BASE PART NUMBER: SERIES TTG Two Single Pole switches in one base 6 ACTUATOR STYLE PS T 2 CIRCUIT1 See Circuit Designation Chart. 7 ACTUATOR COLOR lighted 3 A Amber C Clear G Green LU Blue R Red 3 BASIC SWITCH NUMBER TA On-None-Off TB On-None-On P Paddle unlighted 2 B Black W White TC LTA On-Off-On On-None-Off, Lighted 8 BASE COLOR2 B 4 RATING 10 5A 250VAC, 10A 125VAC, 1/2HP 125-250VAC 11 5A 250VAC, 10A 125VAC, 5A 125VAC L 20 10A 250VAC, 15A 125VAC, 3/4HP 125-250VAC 21 10A 250VAC, 15A 125VAC 22 10A 250VAC, 15A 125VAC, 20A 125-250VAC H, 3/4HP 125-250VAC W Black 9 LENS COLOR4 A C 5 TERMINATION/FUNCTION Solder Lug .250 Tab QC .187 Tab QC Wire Leads On-None-Off 0 1 3 5 (On)-None-Off AB D F On-None-(Off) LM R T On-None-On 01 3 5 On-None-(On) AB D F On-Off-On 01 3 5 G LU Amber Clear incandescent 6V 6 volt 12V 12 volt 18V 18 volt 24V 24 volt 28V 28 volt .156[3.96] DIA .250[6.35] .055[1.40] DIA 6.000[152.40] .250[6.35] .250[6.35] .250 TAB (Q.C.) SOLDER LUG .220[5.59] .187[4.74] .187 TAB (Q.C.) TERMINAL TYPE .520[13.20] .812[20.62] 125 volt neon 250 volt neon Notes: Imprinting is available. Consult factory. Panel Cut-Out Recommendations: For sheet metal panels, switch must enter panel in same direction as the punch. (Burr on bottom.) Test cut hole in actual material. 1 TG available with circuits A, B, C, D, E, F, L, T, U G, H, I, J, M, N, P, Q, R, T, U, V, Y, Z. 2 Custom colors are available. Consult factory. 3 Specify lens color for LTA with rocker only. 4 Specify lens color for LTA with paddle actuators only. ( ) Indicates momentary function. 1.240[31.49] .050[1.27] RRed WWhite neon 125N 250N .375[9.52] .860[21.84] White Green Blue 10 LAMP VOLTAGE .069[1.75] DIA 1.155[29.33] Short Paddle Rocker .500[12.70] INTEGRATED WIRE LEAD (no exposed conductors) 1.125[28.57] .275[6.98] 1.000[25.40] .375[9.52] .994[25.24] 1.120[28.44] PADDLE *Manufacturer reserves the right to change product specification without prior notice. SHORT PADDLE MOUNTING HOLE Panel Thickness: .020[.508] min. to .250[6.35] max. 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com Circuit Designation Chart | 3 1 1 4 1 2 2 2 5 2 5 2 5 3 3 3 6 3 6 3 6 B 4 2 C 4 5 3 D 4 2 2 3 3 1 E 4 1 2 2 6 4 3 3 6 I J 1 4 1 4 1 4 1 4 2 5 2 5 2 5 2 5 3 6 3 6 3 6 3 6 1 4 1 5 2 6 3 1 4 1 4 2 5 2 5 3 6 3 6 3 4 1 4 5 3 6 1 4 2 5 3 6 T 1 4 1 2 5 2 5 2 3 6 3 6 3 1 4 5 2 5 2 5 6 3 6 3 6 1 Z CONTACT TERMINAL Will make contact with switching lever CONTACT TERMINAL AND SWITCH LEVER ISOLATED TERMINAL BULB Does not make contact with switching lever REV_SW_TTG_0912 60 Johnson Avenue • Plainville, CT 06062–1177 • Phone: (860) 793–9281 • Fax: (860) 793–9231 Email: [email protected] • www.carlingtech.com