CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS SL Low Profile (φ6.3) series Low ESR, High Capacitance, High ripple current. Low Profile(Height 4.2mm). Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). SA Lower Profile SL Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 15 to 330µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. Endurance After 2 minutes' application of rated voltage at 20°C Test condition 105°C, rated voltage 2000Hrs. Capacitance change Within ±20% of initial value before test tan δ 150% or less than the initial specified value ESR( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. Size List (ESR) Cap [µF] R.V.(V) S.V.( V) [Upper value : φD×L(mm), Lower value : ESR(mΩ)] 2.5 6.3 16 25 2.8 7.2 18.4 6.3×4.2 (45) 28.7 6.3×4.2 (55) 6.3×4.2 (16) 6.3×4.2 (18) 6.3×4.2 (18) 6.3×4.2 (18) 15 100 150 220 330 6.3×4.2 (16) 6.3×4.2 (16) Dimension table in next page. (mm) φD×L W H C R P 6.3×4.2 6.5 6.5 7.2 0.5 to 0.9 2.1 CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS SL series Standard Ratings Rated Voltage Surge Voltage (V) (V) (code) 2.5 (0E) 6.3 (0J) 2.8 7.2 Rated Capacitance (µF) Case Size φD×L (mm) tan δ Leakage Current (µA, 2min.) ESR (mΩ, 100kHz) Rated Ripple Current (mArms) NICHICON FPCAP 100 6.3×4.2 0.12 300 16 3500 RSL0E101MCN1GB FP-2R5ME101M-SLR 220 6.3×4.2 0.12 300 16 3500 RSL0E221MCN1GB FP-2R5ME221M-SLR 330 6.3×4.2 0.12 413 16 3500 RSL0E331MCN1GB FP-2R5ME331M-SLR 100 6.3×4.2 0.12 315 18 3200 RSL0J101MCN1GB FP-6R3ME101M-SLR 150 6.3×4.2 0.12 473 18 3200 RSL0J151MCN1GB FP-6R3ME151M-SLR 220 6.3×4.2 0.12 693 18 3200 RSL0J221MCN1GB FP-6R3ME221M-SLR 16 (1C) 18.4 15 6.3×4.2 0.12 300 45 1900 RSL1C150MCN1GB FP-016ME150M-SLR 25 (1E) 28.7 15 6.3×4.2 0.12 100 55 1700 RSL1E150MCN1GB FP-025ME150M-SLR Frequency Characteristics (The frequency characteristics are typical and not a guaranteed value.) 6.3V 220µF Impedance 6.3V 220 µF Frequency (kHz) Frequency (kHz) Taping specifications are given in page 28. Recommended land size, soldering by reflow are given in page 25. Please refer to page 3 for the minimum order quantity. CAT.8100D