P10CUI-xxxxZ(H30)LF PM3-SERIES Rev.02-2009 2 Watt Unregulated Dual Separate Output SIP7 Case 1 - 3 kV DC I/O Isolation Low Ripple and Noise Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PM3 series P10CUI-xxxxZ(H30)LF is a family of cost effective 2 W dual separate output DC/DC converters. These converters are in an ultra miniature SIP7 case. Devices are encapsulated. High performance features: 1000VDC up to 3000VDC input/output isolation, high efficiency operation, output voltage accuracy of ±3% maximum, input range of ±10% tolerance and low output ripple and noise. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ ± 10% Capacitor 20 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation (20% - 100%) Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 3% Short Term ± 1.2% / 1% Vin Change ± 10% (3.3 Vout Models: ± 20%) 75 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1000 VDC (3000 VDC optional)* 60 pF, typ. 1000 M Ohm 80 kHz (Variable) 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Non Conductive Black Plastic (UL94V-0 rated) Epoxy (UL94V-0 rated) ~ 2.7g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection (10 mm distance required) Soldering 260°C, max. (1.5 mm from case 10s.) PM3-Series – P10CUI-xxxxZ(H30)LF – Dual Separate Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Dual Separate Output ) ) mA) (mA ad (mA ad ( ) d o a L C o L D F)² Lo ull d (u ( No e (V F u ll ) nt F a t g t e e o n a n % r g t ( r L l e e y rr rr lta or Vo Cu ienc t Cu put Cu t Vo acit put put In p u In p u In O ut O ut Effic Cap ) VDC Order # DUAL SEP. OUTPUT P10CUI-05053R3ZLF P10CUI-05057R2ZLF P10CUI-050509ZLF P10CUI-050512ZLF P10CUI-050515ZLF P10CUI-12053R3ZLF P10CUI-12057R2ZLF P10CUI-120509ZLF P10CUI-120512ZLF P10CUI-120515ZLF P10CUI-24053R3ZLF P10CUI-24057R2ZLF P10CUI-240509ZLF P10CUI-240512ZLF P10CUI-240515ZLF 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 35 35 35 35 35 25 25 25 25 25 12 12 12 12 12 519 519 519 500 500 216 216 216 208 208 108 108 108 104 104 5, 3.3 5, 7.2 5, 9 5, 12 5, 15 5, 3.3 5, 7.2 5, 9 5, 12 5, 15 5, 3.3 5, 7.2 5, 9 5, 12 5, 15 200, 200 200, 139 200, 111 200, 83 200, 67 200, 200 200, 139 200, 111 200, 83 200, 67 200, 200 200, 139 200, 111 200, 83 200, 67 77 77 77 80 80 77 77 77 80 80 77 77 77 80 80 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 P10CUI-050505ZLF P10CUI-057R27R2ZLF P10CUI-050909ZLF P10CUI-051212ZLF P10CUI-051515ZLF P10CUI-120505ZLF P10CUI-127R27R2ZLF P10CUI-120909ZLF P10CUI-121212ZLF P10CUI-121515ZLF P10CUI-240505ZLF P10CUI-247R27R2ZLF P10CUI-240909ZLF P10CUI-241212ZLF P10CUI-241515ZLF 5 5 5 5 5 12 12 12 12 12 24 24 24 24 24 35 35 35 35 35 25 25 25 25 25 12 12 12 12 12 500 500 500 487 487 208 208 208 203 198 104 104 104 101 98 5, 5 7.2, 7.2 9, 9 12, 12 15, 15 5, 5 7.2, 7.2 9, 9 12, 12 15, 15 5, 5 7.2, 7.2 9, 9 12, 12 15, 15 200, 200 139, 139 111, 111 83, 83 67, 67 200, 200 139, 139 111, 111 83, 83 67, 67 200, 200 139, 139 111, 111 83, 83 67, 67 80 80 80 82 82 80 80 80 82 84 80 80 80 82 85 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 If you need other specifications, please enquire. * For optional 3kV DC I/O Isolation, please add “H30” before LF! Example: P10CUI-050505ZH30LF for 3kV PM3-Series – P10CUI-xxxxZ(H30)LF – Dual Separate Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating 2.1 (0.9) All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 0.50 (0.02) 0.50 (0.02) 6.00* (0.24) 19.50 (0.76) * The thickness of 48Vin voltage is 7.20(0.28) PEAK Modelcode Datecode 1 2.54 (0.10) 2 4 5 6 7 SIP 7 – PLASTIC CASE 15.24 (0.60) PIN CONNECTIONS # DUAL SEP. 1 +Vin 2 - Vin 4 +V1out 5 - V1out 6 +V2out 7 - V2out Same Pinning for 3kV Models! App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by minimal Vin and constant resistive load. - Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications. PM3-Series – P10CUI-xxxxZ(H30)LF – Dual Separate Output – SIP7 - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3