DC-AC INVERTER UNIT PS-DA0201-316(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC/AC inverter is developed for dual lamps. Optimized for AUO: G150XG03 V3 APPLICABLE LCD: 6.4 to 15 inches double lamps Lamp voltage 600 Vrms Lamp current 2 x 8 mArms Lamp Start Up Voltage 1.500 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open lamp detection RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -10°C ~ +50°C -40°C ~ +85°C 95 %RH max Unit : mm Weight :24,2 (g) typ. 160 x 25 x 10 mm Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 + CN3 Input side CN1: Pin No. Symbols Vin CN 1-1 GND CN 1-2 Vrmt CN 1-3 Vbr CN 1-4 CN 1-5 Qty. 1 1 2 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K SM02(8.0)B-BHS-1-TB Note t=1mm JST or equal JST or equal Output side CN2: Ratings 10.8 ~ 13.2 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 2.5 Vdc N.C. Pin No. CN 2-1 CN 2-2 Ratings 600 Vrms (8 mArms) (GND) Output side CN3: Pin No. CN 3-1 CN 3-2 - Symbols Vhigh Vlow Symbols Vhigh Vlow Ratings 600 Vrms (8 mArms) (GND) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.1, 21st May 2014 DC-AC INVERTER UNIT PS-DA0201-316(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No load Shutdown Iout Iout Iin F Vopen Tsd Note 1 : Note 2: Specification Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. 12±1.2 12±0.6 12±1.2 12±1.2 11.4 12±1.2 0.0 2.5 0.0 0.0 0.0 0.0 -10 ~ +50 -10 ~ +50 -10 ~ +50 -10 ~ +50 -10 ~ +50 -10 ~ +50 7.5 45 1.300 - 8.0 30 1.1 50 1.500 1.0 8.5 1.3 55 1.900 - Unit Note mArms % Adc kHz Vrms sec Dut y 100% Dut y M in wit hout load Please keep a minimum of 2mm clearance in all directions between inverter high voltage areas and any conductors. Please provide Vcc before applying any control signals into inverter. Reverse the sequence during power off which is control signal off first then Vcc. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.1, 21st May 2014