DC-AC INVERTER UNIT PS-DA0245-01(S) (12 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for quad lamps. Optimzed for Sharp LQ150X1LGN2A APPLICABLE LCD: Lamp Voltage 1050 Vrms Lamp Current 2 x 4.5 mArms Lamp Start Up Voltage 2.400 Vrms (Vin : 12 Vdc) FEATURES : Wide Operating temperature range Alarm signal function PWM dimming type. Current Feedback Circuit Remote ON/OFF Open Lamp Detection Extra high starting Voltage RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -10°C ~ +60°C -20°C ~ +85°C 95 %RH max 130 x 40 x 9 mm Unit : mm Weight :28 (g) typ. Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S7B-PH-SM3 Note t=1m m JST or equal 3 Connector CN2 + CN3 2 SM02B-BHSS-1-TB JST or equal Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.0, 26th January 2011 DC-AC INVERTER UNIT PS-DA0245-01(S) (12 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) Output side CN2: Input side CN1: Pin No. CN 2-1 Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 Symbols Vin Vin GND GND Vbr Vs t Ratings 10,8 ~ 13,2 Vdc 10,8 ~ 13,2 Vdc 0 ~ 5.0 Vdc 0 / 5 Vdc Pin No. CN 3-1 CN 1-7 Vrm t 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON CN 3-2 Symbols Ratings Vhigh 1050 Vrm s (4.5 m Arm s ) GND CN 2-2 - Output side CN3: Symbols Ratings Vhigh 1050 Vrm s (4.5 m Arm s ) GND - ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Input Current Frequency Open Circuit Voltage No load Shutdown Iout Iout Iin1 Iin2 F Vopen Tsd Note 1 : Specification Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. 12±1.2 12±0.6 12±1.2 12±1.2 12±1.2 11.4 12±1.2 5.0 0.0 5.0 5.0 5.0 5.0 5.0 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 -10 ~ +60 4.0 4.5 13 1.01 50 2.400 1.0 5.0 40 2.200 - 1.3 1.0 55 2.600 - Unit Note mArms % Adc mAdc kHz Vrms sec Duty 100% Dut y min without load Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Open circuit on all lamps for more than 3 sec., will shut the inverter down. Before apply any control signal into inverter, please provide Vcc first. Please follow the reversed sequence during power off. Power off control signal first, then power off Vcc. Note 2 : Note 3: TEST CIRCUIT : F Vopen SW2 Iin A Vin 10.8 ~ 13.2 V 1000:1 PROBE F CN1-1 CN1-2 V SW 1 CN1-3 CN1-4 CN1-5 V ~ CN2-1 RL1 CL1 T1 A ~ CN2-2 Vbr 0 ~ 5.0 Vdc Operation of unit a Operation b Non operation Iout 1 SW3 SW4 CN3-1 Vst 5 Vdc V Vrmt 0 / 5 Vdc CN1-6 RL1 CL1 a V b SW1 A ~ CN1-7 CN3-2 Iout 1 SW5 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.0, 26th January 2011