DC-AC INVERTER UNIT PS-DA0201-04(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. APPLICABLE LCD: 6.4 to 18 inches double lamp type Lamp Voltage 800 Vrms Lamp Current 2 x 6 mArms Lamp Start Up Voltage 1.800 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open Lamp Detection RoHS compliant (S) High Efficiency Wide Dimming Range TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -20°C ~ +70°C -40°C ~ +85°C 95 %RH max 160 x 25 x 10mm Pin 1 Pin 1 Pin 1 Unit : mm Weight :24,2 (g) typ. Pin 1 Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K Note t=1mm JST or equal 3 Connector CN2 + CN3 2 SM02(8.0)B-BHS-1-TB JST or equal Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 Symbols Vin GND Vrmt Vbr N.C. Ratings 10.8 ~ 13.2 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 2.5 Vdc - Output side CN2 + CN3: Pin No. Symbols Ratings VHIGH1 800 Vrms (6 mArms) CN 2-1 N.C. CN 2-2 CN 2-3 VLOW GND Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.5, 27th September 2011 DC-AC INVERTER UNIT PS-DA0201-04(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Unit Note 6.6 1.2 55 1.900 mArms % Adc kHz Vrms Dut y 100% - sec wit hout load Vin (V) Vbr (V) Tu (°C) Min. Typ. Max. Iout Iout Iin F Vopen 12±1.2 12±0.6 12±1.2 12±1.2 11.4 0.0 2.5 0.0 0.0 0.0 -20 ~ +70 -20 ~ +70 -20 ~ +70 -20 ~ +70 -20 ~ +70 5.4 45 1.500 6.0 20 0.88 50 1.700 Tsd 12±1.2 0.0 -20 ~ +70 - 1.0 No load Shutdown Note 1 : Specification Dut y M in Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Before apply any control signal into inverter, please provide Vcc first. Please follow the reversed sequence during power off. Power off control signal first, then power off Vcc. Note 2: TEST CIRCUIT : F A Vin 12 V Iin 1000:1 PROBE F CN1-1 SW3 V CN2-1 CN1-2 Vrmt 0.4 / 5 Vdc a V b Vopen V ~ SW1 CN1-3 CL1 RL1 A ~ T1 CN2-2 SW4 SW 1 Operation of unit a Operation b Non operation Iout1 SW5 CN1-4 Vbr 0 ~ 2.5 Vdc CN3-1 CL2 RL2 N.C. CN1-5 CN3-2 SW6 A ~ Iout2 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.5, 27th September 2011