DC-AC INVERTER UNIT PS-DA0201-01(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. APPLICABLE LCD: 6.4 to 15 inches double lamp type Lamp Voltage 714 Vrms Lamp Current 2 x 7 mArms Lamp Start Up Voltage 1.500 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open Lamp Detection RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH Components No. 1 2 3 Unit : mm Weight :24,2 (g) typ. 160 x 25 x 10 mm Note: Please use plastic screw in case of a non-insulating mounting base! Part Description PCB Connector CN1 Connector CN2 + CN3 Input side CN1: Pin No. Symbols Vin CN 1-1 GND CN 1-2 Vrm t CN 1-3 Vbr CN 1-4 CN 1-5 0°C ~ +60°C -40°C ~ +85°C 95 %RH max Qty. 1 1 2 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K SM02(8.0)B-BHS-1-TB Note t=1m m JST or equal JST or equal Output side CN2: Ratings 10.8 ~ 13.2 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 2.5 Vdc N.C. - Pin No. CN 2-1 CN 2-2 Symbols Vhigh Vlow Ratings 714 Vrm s (7 m Arm s ) (GND) Output side CN3: Pin No. CN 3-1 CN 3-2 Symbols Vhigh Vlow Ratings 714 Vrm s (7 m Arm s ) (GND) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.6.7, 31st August 2010 DC-AC INVERTER UNIT PS-DA0201-01(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Specification Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen 12±1.2 12±0.6 12±1.2 12±1.2 11.4 0.0 2.5 0.0 0.0 0.0 0 0 0 0 0 Ts d 12±1.2 0.0 0 ~ +60 No load Shutdown Note 1 : Vin (V) Vbr (V) Tu (°C) ~ +60 ~ +60 ~ +60 ~ +60 ~ +60 Unit Note 7.5 1.2 55 1.900 m Arm s % Adc kHz Vrm s Duty 100% - s ec wit hout load Min. Typ. Max. 6.5 45 1.300 7.0 20 0.88 50 1.500 - 1.0 Dut y M in Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Before apply any control signal into inverter, please provide Vcc first. Please follow the reversed sequence during power off. Power off control signal first, then power off Vcc. Note 2: TEST CIRCUIT : F A Vin 12 V Iin 1000:1 PROBE F CN1-1 CN2-1 a V b SW 1 Operation of unit a Operation b Non operation SW3 V CN1-2 Vrmt 0.4 / 5 Vdc Vopen V ~ SW1 CN1-3 CL1 RL1 A ~ T1 CN2-2 SW4 Iout1 SW5 CN1-4 Vbr 0 ~ 2.5 Vdc CN3-1 CL2 RL2 N.C. CN1-5 CN3-2 SW6 A ~ Iout2 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.6.7, 31st August 2010