SMD RESISTOR ** ANTI-SULFUR RoHS RMP Series: Higher Power, Thick Film INTRODUCTION DIMENSIONS The RMP Series is a higher power (high wattage) version of the standard RM Series Thick Film SMD Resistor. The RMP Series SMD Resistor is made with a specially formulated substrate and with an advanced process used to deposit the film. As a result, power ratings surpass standard series, and they are ANTISULFUR. These resistors are AEC-Q200 qualified and are suitable for all applications (automotive, lighting, power, etc). D Glass Passivation H L Max. Dimension (mm) Size Code • Basic Thick Film Resistors see RM Series • High Power Thick Film see RMH Series • Anti-Sulfur Thick Film Resistors see RMS Series • Thin Film Resistor see RMT series • Fusible Resistors see RMF Series • Thick Film Array Chip see RCN Series • Metal Array Low-Resistance see LR Series W C RMP06 (0603) RMP10 (0805) RMP12 (1206) RMP25 (1210) RMP50 (2010) RMP50S (1812) RMP2W (2512) RMP2WS (1218) L W H C D 1.60±0.20 2.00±0.20 3.05±0.10 3.05±0.10 5.00±0.20 4.50±0.10 6.30±0.20 3.10±0.10 0.80±0.15 1.25±0.15 1.60±0.20 2.50±0.20 2.50±0.20 3.00±0.10 3.20±0.20 4.60±0.10 0.40±0.10 0.50±0.15 0.55±0.15 0.55±0.15 0.55±0.10 0.55±0.05 0.55±0.10 0.55±0.05 0.20±0.10 0.30±0.15 0.40±0.20 0.50±0.20 0.60±0.20 0.55±0.20 0.20±0.10 0.40±0.15 0.50±0.20 0.50±0.20 0.60±0.20 0.70±0.20 0.60±0.20 0.50±0.20 0.60±0.20 0.40±0.20 PART NUMBER EXAMPLE RESISTANCE CODE RMP 10 R - 10K - J Series Tolerance Code Size Code Taped & Reeled Ohms 0.0 Code 0R0 100R 1K5 100 1.5K 15K 1.5 Meg 15K 1M5 Resistance Code SIZE CODE & RESISTANCE RANGE Code Size Rated Power at 70°C RMP06 (0603) 0.125W RMP10 RMP12 RMP25 RMP50 RMP50S RMP2W (0805) (1206) (1210) (2010) (1812) (2512) RMP2WS (1218) 0.25W 0.50W 0.66W 1.0W 1.0W 2.0W 2.0W Max. Working Voltage 50V 150V 200V 200V 200V 200V 250V 250V Max. Overload Voltage 100V 300V 400V 400V 400V 400V 500V 500V Resistance Range T.C.R. (PPM/°C) ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 ±400 ±200 ±100 B (±0.1%) D (±0.5%) 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ 10Ω ~ 1MΩ F (±1%) J (±5%) 1Ω ~ 9.9Ω 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 1Ω ~ 9.9Ω 10Ω ~ 10MΩ 10Ω ~ 10MΩ Page 1 of 4 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB07 2014.01.13 SMD RESISTOR ** ANTI-SULFUR RoHS RMP Series: Higher Power, Thick Film PERORMANCE CHARACTERISTICS Operating Temperature Range -55°C to +155°C Power Derating Curve Power Ratio (%) 100 80 1 60 40 155°C 1 20 1 0 -55 0 20 40 60 70 80 100 120 140 160 Ambient Temperature (°) Power rating or current rating is in the case based on continuous full-load at ambient temperature of 70ºC. For operation at ambient temperature in excess of 70ºC, the load should be derated in accordance with figure of derating Curve. Voltage Rating or Current Rating Resistance Range: >1Ω Rated Voltage: The resistor shall have a DC continuous working voltage or a RMS AC continuous working voltage at commercial-line frequency and wave form corresponding to the power rating, as determined formula as follows: E = Rated Voltage (V) P = Power Rating (W) R = Nominal Resistance (Ω) E = √P x R Operation and Storage Temperature MIN MAX -55ºC 70ºC Storage temperature 20ºC 30ºC Storage humidity 30% 70ºC Operation temperature Soldering Profile +5 250 Peak: 250 0 ºC 230ºC or Higher 1 200 180ºC Pre Heating Zone 1 150 150ºC 90 ± 30 s 1 30 ± 10 s 100 Soldering Zone 1 50 Heating Time Page 2 of 4 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB07 2012.12.20 SMD RESISTOR ** ANTI-SULFUR RoHS RMP Series: Higher Power, Thick Film TEST PROCEDURES & REQUIREMENTS Test Item Procedure Test Method Requirements Temperature JIS C 5201-1 Coefficient of Resistance (T.C.R.) Clause 4.8 -55°C ~ +155°C, 20°C is the reference temperature Refer to Ratings Short Time Overload General: 2.5 times RCWV or Max. Overload voltage for 5 seconds High Power: 2.5 times RCWV or Max. Overload voltage for 2 seconds ±1: ±(1.0%+0.05Ω) ±5: ±(2.0%+0.1Ω) JIS C 5201-1 Clause 4.13 +5 250 Peak: 250 0 ºC 230ºC or Higher 1 200 180ºC Pre Heating Zone 1 150 IR Reflow Sony SS-00254 1 100 150ºC 30 + 10 s Soldering Zone 1 50 ±1: ±(1.0%+0.05Ω) ±5: ±(2.0%+0.1Ω) 90 + 30 s Heating Time Leaching Sony SS-00254-9 260 ±5°C for 30 seconds > 95% Coverage Soldering Heat JIS C 5201-1 Clause 4.18 260 ±5°C for 10 seconds ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Temperature Cycling JIS C 5201-1 Clause 4.19 -55°C ~ +155°C, 5 cycles 0.1% ' 0.5% ' 1% ±(0.5%+0.05Ω) 2% ' 5% ±(1.0%+0.1Ω) Electric Iron Sony SS-00254-5 Preheating termperature: 350 ± 5°C Electric Iron preheating time: 3 +1/-0 sec. ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Resistance to Solvent JIS C 5201-1 Clause 4.29 The tested resistor be immersed into isopropyl alcoho of 20~25°C for 60 seconds. Then the resistor is left in the room for 48 hours. ±1: ±(0.5%+0.05Ω) ±5: ±(1.0%+0.05Ω) Load Life in Humidity JIS C 5201-1 Clause 4.24 40 ± 2°C, 90~95% R.H. or Max. working voltage for 1000 hours with 1.5 hrs “ON” and 0.5hr “OFF”. 0.1% ' 0.5% ' 1% ±(0.5%+0.05Ω) 2% ' 5% ±(3.0%+0.1Ω) Load Life (Endurance) JIS C 5201-1 Clause 4.25 70 ± 2°C, or Max. working voltage for 1000 hours with 1.5 hrs “ON” and 0.5hr “OFF”. 0.1% ' 0.5% ' 1% ±(1.0%+0.05Ω) 2% ' 5% ±(3.0%+0.1Ω) Terminal Bending Strength JIS C 5201-1 Clause 4.33 Bending once for 5 seconds D: RMP Series 0402 ' 0603 ' 0805 = 5mm RMP Series 1206 ' 1210 ' 1812 = 3mm RMP Series 1218 ' 2010 ' 2512 ' 2030 = 2mm ±1: ±(1.0%+0.05Ω) ±5: ±(1.0%+0.05Ω) Insulation Resistance JIS C 5201-1 Clause 4.6 Max Overload Voltage for 1 min. ≥ 10G Page 3 of 4 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB07 2014.01.13 SMD RESISTOR ** ANTI-SULFUR RoHS RMP Series: Higher Power, Thick Film PACKAGE & DIMENSION (mm) Unit: mm Type Size A ΦB ΦC ΦD W ΦM RMP06 (0603) 7" 5K / Reel 2.0 + 0.5 13.5 + 1.0 21 + 1.0 60 + 1.0 11.5 + 2.0 178 + 2.0 RMP10 (0805) 10" 10K / Reel 2.0 + 0.5 13.5 + 1.0 21 + 1.0 100 + 1.0 11.5 + 2.0 254 + 2.0 RMP12 (1206) 13" 20K / Reel 2.0 + 0.5 13.5 + 1.0 21 + 1.0 100 + 1.0 11.5 + 2.0 330 + 2.0 RMP25 (1210) 7" 5K / Reel 2.0 + 0.5 13.5 + 1.0 21 + 1.0 60 + 1.0 11.5 + 2.0 178 + 2.0 7" 4K / Reel 2.0 + 0.5 13.5 + 1.0 21 + 1.0 60 + 1.0 16.0 + 2.0 178 + 2.0 RMP50 (2010) RMP50S (1812) RMP2W (2512) RMP2WS (1218) TAPING SPECIFICATION Paper Type (P= 2.0 ± 0.1) Unit:mm Type A B W E F G H T ΦD RMP06 (0603) 1.05 + 0.20 1.80 + 0.20 8.0 + 0.20 1.75 + 0.10 3.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.60 + 0.10 1.50 + 0.10 RMP10 (0805) 1.55 + 0.20 2.30 + 0.20 8.0 + 0.20 1.75 + 0.10 3.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.60 + 0.10 1.50 + 0.10 RMP12 (1206) 1.90 + 0.20 3.50 + 0.20 8.0 + 0.20 1.75 + 0.10 3.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.60 + 0.10 1.50 + 0.10 RMP25 (1210) 2.85 + 0.20 3.50 + 0.20 8.0 + 0.20 1.75 + 0.10 3.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.60 + 0.10 1.50 + 0.10 Embossed Type (P= 4.0 ± 0.1) Unit:mm Type RMP50 (2010) A B W E F G H T ΦD ΦD1 T1 2.8 + 0.20 5.60 + 0.20 12 + 0.10 1.75 + 0.10 5.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.23 + 0.10 1.50 + 0.10 1.50 + 0.10 0.85 + 0.15 RMP50S (1812) 3.40 + 0.20 6.70 + 0.20 12 + 0.10 1.75 + 0.10 5.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.23 + 0.10 1.50 + 0.10 1.50 + 0.10 0.85 + 0.15 RMP2W (2512) 3.30 + 0.20 4.60 + 0.20 12 + 0.10 1.75 + 0.10 5.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.23 + 0.10 1.50 + 0.10 1.50 + 0.10 0.85 + 0.15 RMP2WS (1218) 3.30 + 0.20 4.60 + 0.20 12 + 0.10 1.75 + 0.10 5.5 + 0.05 4.0 + 0.10 2.0 + 0.05 0.23 + 0.10 1.50 + 0.10 1.50 + 0.10 0.85 + 0.15 Page 4 of 4 RFE International • Tel:(949) 833-1988 • Fax:(949) 833-1788 • E-Mail [email protected] C2BB07 2014.01.13