F E D C B AT ALL TIMES WATER RESISTANT CONNECTORS NOT A n1,04 (15x) IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING COMPOUND D 6,3 `0,3 8,8 `0,3 D 39,4 +- 0,2 0 24,99 +- 0,12 0,13 5,73 +- 0,17 0,08 21,1 +- 0,2 0 3,6 +- 0,25 0 16,41 +- 0,05 0,2 0,02 8 +- 0,23 C C 10° SEE NOTE 7 O-RING 6HDD15SAM99B30X CONEC ABC 4-40 UNC 9,4 4,6 SEE NOTE 13 4-40 UNC SW 4,8 B B NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATORS: PBT GF UL 94 V-0, BLACK 4. SIGNAL CONTACTS: COPPER ALLOY PLATING: GOLD FLASH over NICKEL SOLDER CUP ACCEPTS CABLE AWG 22 5. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 6. COLLARS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. FRAME: ZINC DIE CAST; NICKEL PLATED 8. HEXLOCKING SCREW: STAINLESS STEEL 9. O-RING: SILICON; BLUE 10. SEALING COMPOUND: PUR; BLUE 11. RECOMMENDED PANEL CUT-OUT SEE SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.40Ncm (3.5 in.LB) Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 13. CONNECTOR IS PART MARKED: 6HDD15SAM99B30X CONEC ABC scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 13.12.10 Henneboel D-SUB HD FEMALE appd. 14.12.10 Fischer 15pos. SOLDER CUP with threaded insert and hexlocking screw dwg no: Inventor 10 DIN- norm d-old Origin rev. description D date part no: name C A3 sh: 1 15K1A768 R a B 6HDD15SAM99B30X A F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350°C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C 11,4 `0,1 RECOMMENDED PANEL CUT-OUT 20,5 `0,1 i 0,26 A B B n3,1 `0,05 (2x) B 10°`1° R3 , A F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 25 `0,1 i 0,26 B 4` 0, 1 3 A scale: material: tolerance 3:1 see sheet 1 dim. in mm date drawn 13.12.10 Henneboel appd. 14.12.10 Fischer A title: name PANEL CUT-OUT D-SUB COMBINATION FEMALE Solder cup; with hexlocking screw dwg no: Inventor 10 norm d-old 15K1A768 R a Origin rev. description D date part no: name C B SEE SHEET1 A DINA3 sh: 2