F E D C n0,6 `0,05 (5x) NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 240°C FOR 5 SEC. AND SOLDER PREHEAT 120°C FOR 120 SEC.) 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATOR: PBT GF UL 94 V-0, GREEN 4. SIGNAL CONTACTS: COPPER ALLOY D B A (5:1) 3,3 `0,2 6,35 `0,3 SEALING COMPOUND PLATING: GOLD FLASH over NICKEL 5. HIGH POWER CONTACTS 15A: COPPER ALLOY D 300µin COPPER/40-120µin NICKEL/120-200µin TIN 7. THREADED INSERTS: COPPER ALLOY; max. 2 PLATING TERMINATION SIDE: 160-240µin TIN over 80µin NICKEL 6. METAL BRACKETS: ZINC DIE CAST; 4,8 `0,3 7,64 `0,3 PLATING MATING AREA: GOLD FLASH over NICKEL min. 200µin TIN over 80µin NICKEL 8. HEXLOCKING SCREWS: STAINLESS STEEL 9. FRAME: ZINC DIE CAST; NICKEL PLATED 10. O-RING: SILICON; BLUE 3,6 +- 0,25 0 12. SEALING COMPOUND: PUR; BLUE 13. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 5,7 +- 0,22 0,18 11. RUBBER GASKET: TPE 35N cm (3.1in.LB)/max. 40N cm (3.5 in.LB) 15. CONNECTOR IS PART MARKED: 6007W2PAT59S20X CONEC ABC C 8,26 +- 0,22 0,03 47,7 +- 0,3 0 POS. 1 RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATER 33,3 +- 0,15 0,1 POS. 3 C 25,17 +- 0,2 0,05 21,1 +- 0,3 0 POS. A1 6007W2PAT59S20X CONEC ABC O-RING 4-40 UNC 9,4 n1,9 (2x) 4,6 SW 4,8 Directive 2002/95/EC RoHS compliant E DO NOT ALTER CAD DRAWING BY HAND AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 4-40 UNC F B SEE NOTE 9 SEE NOTE 15 A 10,5 `0,3 9,9 `0,2 METAL BRACKET 5,65 `0,2 B 5,93 `0,3 Ø3,18 (2x) 10° scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date drawn 25.07.12 Henneboel appd. 25.07.12 Koch A title: name D-SUB COMBINATION MALE 90° 7W2S with threaded insert, metal bracket, hexlocking screw dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 15K1A1099 R a B sh: 1/2 6007W2PAT59S20X A F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) D D 33,3 +- 0,15 0,1 6,86 `0,1 1,37 `0,1 FRONTPANEL 2,5 `0,1 3,63 `0,1 P.C.B. EDGE 3,35 9,25 C Ø2,3 (2x) 1 A1 2,84 `0,1 n3,1 `0,1(2x) C n1 +- 0,1 0 (5x) 2,77 `0,1 RECOMMENDED PANEL CUT-OUT 28,8 `0,1 i 0,26 A B i 0,26 B B n3,1 `0,05 (2x) 11,4 `0,1 B F E DO NOT ALTER CAD DRAWING BY HAND 33,3 `0,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH A R3 10°`1° ,4 ` 0, 13 A scale: material: tolerance 2:1 see sheet 1 dim. in mm date drawn 25.07.12 Henneboel P.C.B. HOLE DRILLINGS appd. 25.07.12 Koch RECOMMENDED PANEL CUT-OUT D-SUB Combination Male 90° 7W2P dwg no: DINA3 15K1A1099 sh: 2/2 norm d-old R a Original rev. description D date A title: name part no: name C B SEE SHEET 1 A