E D C 11 `0,3 6,35 `0,3 (5:1) D 6,13 +- 0,17 0,08 8 +- 0,02 0,23 47,7 +- 0,3 0 C A SEALING COMPOUND 12,45 +- 0,4 0,3 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265°C FOR 8 SEC. AND SOLDER PREHEAT 150°C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL PLATING over COPPER 5. INSULATOR: PBT GF UL 94 V-0; GREEN D 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 8. HIGH POWER CONTACTS 20A: COPPER ALLOY; PLATING MATING SIDE (SEE PART NO.): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL PLATING TERMINATION SIDE: 160-240µin TIN over 80µin NICKEL 9. METAL BRACKETS: ZINC DIE CAST; 300µin COPPER/40-120µin NICKEL/120-200µin TIN 10. WASHERS: COPPER ALLOY; 80µin NICKEL 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. PCB SNAPS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL PCB HOLE: n3.1`0.1; PCB THICKNESS 1.6mm 13. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 15. CONNECTOR IS PART MARKED: 15-00144o CONEC ABC Ø2,85 (3x) NOTES: B 3,6 +- 0,25 0 F C 33,32 +- 0,13 0,12 21,1 +- 0,3 0 24,79 +- 0,05 0,2 10° METAL BRACKET 3,2 `0,2 PRESS FOR FIXING ON PCB B O-RING 13,5 +- 0,4 0,3 B 4-40 UNC 4,6 SW 4,8 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. A Directive 2002/95/EC RoHS compliant E DO NOT ALTER CAD DRAWING BY HAND 4-40 UNC THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 9,4 SEE NOTE 15 F PCB SNAP 10,75 +- 0,4 0,3 15-00144o CONEC ABC scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm date A title: name drawn 25.03.13 Henneboel D-SUB COMB. FEMALE 90° appd. 25.03.13 Fischer 3W3S with metal bracket, hexlocking screw and snap dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 15K1A1282 R a B 15-00144 o sh: 1/2 (see note 8) A F E D C B A P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) D D 33,32 +- 0,13 0,12 6,86 `0,1 6,86 `0,1 A1 8,55 `0,1 n3,1 `0,1 (2x) 10,75 6,85 n3,2 `0,1 (3x) P.C.B. EDGE C C FRONTPANEL RECOMMENDED PANEL CUT-OUT 28,8 `0,1 i 0,26 A B B R3 n3,1 `0,05 (2x) 11,4 `0,1 B i 0,26 B ,4 ` 10° `1° 0,1 3 33,32 `0,1 A F E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH A scale: material: tolerance 5:1 SEE SHEET 1 dim. in mm date drawn 25.03.13 Henneboel P.C.B. HOLE DRILLINGS appd. 25.03.13 Fischer RECOMMENDED PANEL CUT-OUT D-SUB Comb. Female 90° 3W3S dwg no: DINA3 15K1A1282 sh: 2/2 norm d-old R a Original rev. description D date A title: name part no: name C B SEE SHEET 1 A