F E D C AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. 4,74 +- 0,31 0,49 6,35 `0,3 D max. 2 (5:1) SEALING COMPOUND 3,2 `0,2 61,4 +- 0,3 0 C A 5,7 +- 0,2 0,05 3,6 +- 0,25 0 7 `0,3 9,84 `0,3 D n0,6 `0,05 (25x) NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 240°C FOR 5 SEC. AND SOLDER PREHEAT 120°C FOR 120 SEC.) 2. METALSHELLS: COPPER ALLOY; min. 315µin TIN over 40-80µin NICKEL 3. INSULATORS: PBT GF UL 94 V-0, BLACK 4. CONTACTS: COPPER ALLOY PLATING: GOLD FLASH over NICKEL 5. METAL BRACKETS: ZINC DIE CAST; 300µin COPPER/40-120µin NICKEL/120-200µin TIN 6. THREADED INSERTS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL 7. PCB-SNAPS: COPPER ALLOY; min. 200µin TIN over 80µin NICKEL PCB-HOLE: n3,1`0,1mm; PCB-THICKNESS: 1,6mm 8. HEXLOCKING SCREWS: STAINLESS STEEL 9. FRAME: ZINC DIE CAST; NICKEL PLATED 10. O-RING: SILICON, BLUE 11. SEALING COMPOUND: PUR; BLUE 12. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 40Ncm (3.5 in.LB) 14. CONNECTOR IS PART MARKED: 6STD25SAU99R40X CONEC ABC B C 0,02 8 +- 0,23 47,04 `0,13 21,1 +- 0,3 0 38,5 +- 00,25 10° METAL BRACKET B PRESS FOR FIXING ON PCB B O-RING 9,4 4,6 6STD25SAU99R40X CONEC ABC 9,9 `0,2 4-40 UNC 7,15 `0,2 PCB SNAP SEE NOTE 14 SEE NOTE 9 SW 4,8 Directive 2002/95/EC RoHS compliant F E DO NOT ALTER CAD DRAWING BY HAND A THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 4-40 UNC scale: material: tolerance 2:1 (5:1) SEE NOTES dim. in mm A title: date name drawn 03.04.12 Gitinow D-SUB FEMALE 90° appd. 17.04.12 Fischer 25pos. SOLDER PIN ANGLED with threaded insert, metal bracket and snap dwg no: DIN- norm d-old Original rev. description D date part no: name C A3 sh: 1 15K1A1026 R a B 6STD25SAU99R40X A F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) 47,04 `0,13 16,56 `0,1 D D 13,82 `0,1 11,05 `0,1 n1 +- 0,1 0 (25x) n3,1 `0,1 (2x) 8,28 `0,1 5,54 `0,1 2,77 `0,1 2,84 `0,1 P.C.B. EDGE 4,7 `0,1 4,85 10,75 1 FRONTPANEL 1,4 `0,1 C C 4,14 `0,1 6,91 `0,1 9,68 `0,1 12,42 `0,1 15,19 `0,1 RECOMMENDED PANEL CUT-OUT 42,5 `0,1 i 0,26 A B B n3,1 `0,05 (2x) 11,4 `0,1 B R3 10° `0,1° 0, A E DO NOT ALTER CAD DRAWING BY HAND THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH 47,04 `0,1 F i 0,26 B ,4 ` 13 A scale: material: tolerance 3:1 SEE SHEET 1 dim. in mm name drawn 03.04.12 Gitinow P.C.B. HOLE DRILLINGS appd. 17.04.12 Fischer RECOMMENDED PANEL CUT-OUT D-SUB FEMALE 90° 25pos. dwg no: DINA3 15K1A1026 sh: 2 norm d-old R a Original rev. description D date A title: date part no: name C B SEE SHEET 1 A