Ordering information AC-DC Power Supplies Enclosed type PBA300F PBA/PBW PB 1 A 2 300 3 F 4 Recommended EMI/EMC Filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *5 C :with Coating G :Low leakage current U :Operation stop voltage is set at a lower value F3 :Reverse air exhaust type F4 :Low speed fan N1 :with DIN rail Refer to instruction manual 7.1. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA300F-3R3 198 ACIN 100V 3.3V 60A ACIN 200V *3 3.3V 60A PBA300F-5 300 5V 60A 5V 60A PBA300F-7R5 300 7.5V 40A 7.5V 40A PBA300F-12 324 12V 27A 12V 27A PBA300F-15 330 15V 22A 15V 22A PBA300F-24 336 24V 14A 24V 14(16.5)A PBA300F-36 324 36V 9A 36V 9A PBA300F-48 336 48V 7A 48V 7A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] ACIN 100V CURRENT[A] ACIN 200V *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -20 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -20 - 0C *1 0 to +50C *1 TEMPERATURE REGULATION[mV] -20 to +50C *1 DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC INPUT-FG OUTPUT-RC-AUX-FG OUTPUT-RC -AUX OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA300F-3R3 PBA300F-5 PBA300F-7R5 PBA300F-12 PBA300F-15 PBA300F-24 PBA300F-36 AC85 - 264 1f or DC120 - 350 (AC50 or DC70 Please refer to the instruction manual 7. option *4) 3typ 4.1typ 1.6typ 2typ 50/60 (47 - 63) 68typ 74typ 76typ 78typ 78typ 79typ 81typ 71typ 77typ 79typ 81typ 81typ 82typ 84typ 0.98typ (Io=100%) 0.95typ (Io=100%) 20/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 40/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 0.45/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1,DENAN) 3.3 5 7.5 12 15 24 36 60 60 40 27 22 14 9 60 60 40 27 22 14(16.5) 9 20max 20max 36max 48max 60max 96max 144max 40max 40max 60max 100max 120max 150max 150max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 160max 120max 120max 150max 150max 150max 150max 200max 160max 160max 180max 180max 180max 180max 240max 40max 50max 75max 120max 150max 240max 360max 60max 75max 120max 180max 180max 290max 440max 12max 20max 30max 48max 60max 96max 144max 300typ(ACIN 100/200V, Io=100%) *Start-up time is 500ms typ for less than 1minute of applying input again from turning off 20typ (ACIN 100/200V, Io=100%) 2.64 - 3.96 3.96 - 6.00 5.25 - 8.25 8.25 - 13.20 10.50 - 16.50 16.50 - 26.40 25.20 - 39.60 3.30 - 3.40 5.00 - 5.15 7.50 - 7.80 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 Works over 105% of rated current or 101% of peak current and recovers automatically 4.3 - 6.3 6.5 - 8.0 9.0 - 11.6 14.4 - 18.6 18.0 - 23.3 28.8 - 37.2 43.2 - 54.0 LED (Green) Provided Provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -20 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *6 102X42X170mm [4.02X1.65X6.69 inches] (without terminal block and screw) (W XHXD) /1.0kg max Forced cooling (internal fan) *1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3 () means peak current. Peak loading for 10s. And Duty 35% max, refer to Instruction manual in detail. *4 Derating is required.Consult us for details. PBA/PBW-16 *5 Please contact us about safety approvals for the model with option. *6 Please contact us about class C. * A sound may occur from power supply at pulse loading. PBA300F-48 79typ 82typ 48 7 7 192max 300max 150max 400max 200max 500max 480max 600max 192max the input voltage. 38.40 - 56.00 48.00 - 49.92 57.6 - 80.0 PBA300F Block diagram PBA/PBW FUSE AC IN 85 - 264V NOISE FILTER 250V10A INRUSH CURRENT LIMIT RECTIFIER FG RECTIFIER AND FILTER INVERTER DC OUT ±M THERMAL PROTECTION CURRENT SENSING OVER VOLTAGE PROTECTION ACTIVE FILTER RECTIFIER AND FILTER SWITCHING DEVICE CONTROL CONTROL ±S(REMOTE SENSING) RC(REMOTE ON / OFF) VOLTAGE SENSING MASTER SLAVE CONTROL CURRENT SENSING VOLTAGE SENSING CONTROL INTERNAL REGULATOR FAN VB(VOLTAGE BALANCE) CB(CURRENT BALANCE) PG(POWER GOOD) ALARM AUX(12 V 0.1A) External view [0.61] (30) [1.18] CN3 CN2 Name plate CN1 LED Output voltage adjustable potentiometer ¶ Tolerance : ±1 [±0.04] ¶ Weight : 1.0kg max ¶ PCB Material/thickness : FR-4 / 1.6mm [0.06] ¶ Chassis material : Aluminum ]= inches ¶ Dimensions in mm, [ ¶ Mounting torque : 1.2N • m max ¶ Screw tightening torque : 1.6N • m max ¶ The housing for the remote sensing unused is mounted on CN1 ¶ Please connect safety ground to FG terminal on the unit. [4.02] 102 50.5 28.5 [1.12] [1.99] (87) [3.43] (75) [2.95] [0.93] [0.98] 64±0.5 [2.52] 170 6max [6.69] [0.24] AIR FLOW 42 (15.5) 2-M4 Mounting Hole (Bottom sides) 25max [1.65] H V.ADJ M4 74±0.5 [2.91] [0.47] (23.5) 12 (50) [1.97] 12 [0.47] Output terminal(+) 8.6 AC(L) AC(N) FG( ) Output terminal(-) Terminal cover [0.34] (6) M4 10 7 [0.55] [0.39][0.28] [0.24] Name plate (14) 54 [2.13] [0.79] [0.47] 20 ±0.5 12 4-M4 Mounting Hole PBA/PBW-17 Ordering information AC-DC Power Supplies Enclosed type PBA600F PBA/PBW PB 1 A 2 600 3 F 4 Recommended EMI/EMC Filter NAC-16-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *6 C :with Coating G :Low leakage current U :Operation stop voltage is set at a lower value F1 :With Long-Life fan F3 :Reverse air exhaust type F4 :Low speed fan Refer to instruction manual 7.1. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA600F-3R3 396 ACIN 100V 3.3V 120A ACIN 200V *3 3.3V 120A PBA600F-5 600 5V 120A 5V 120A PBA600F-7R5 600 7.5V 80A 7.5V 80A PBA600F-12 636 12V 53A 12V 53A PBA600F-15 645 15V 43A 15V 43A PBA600F-24 648 24V 27A 24V 27(31)A PBA600F-36 648 36V 18A 36V 18A PBA600F-48 624 48V 13A 48V 13A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] ACIN 100V CURRENT[A] ACIN 200V *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -20 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -20 - 0C *1 0 to +50C *1 TEMPERATURE REGULATION[mV] -20 to +50C *1 DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] *4 OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC INPUT-FG OUTPUT-RC-AUX-FG OUTPUT-RC -AUX OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] PBA600F-3R3 PBA600F-5 PBA600F-7R5 PBA600F-12 PBA600F-15 PBA600F-24 PBA600F-36 AC85 - 264 1f or DC120 - 350 (AC50 or DC70 Please refer to the instruction manual 7. option *5) 5.8typ 8.2typ 3typ 4.1typ 50/60 (47 - 63) 70typ 75typ 76typ 79typ 79typ 81typ 82typ 72typ 77typ 79typ 82typ 82typ 84typ 84typ 0.98typ (Io=100%) 0.95typ (Io=100%) 20/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More than 3 sec. to re-start) 40/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More than 3 sec. to re-start) 0.45/0.75max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1, DENAN) 3.3 5 7.5 12 15 24 36 120 120 80 53 43 27 18 120 120 80 53 43 27(31) 18 20max 20max 36max 48max 60max 96max 144max 40max 40max 60max 100max 120max 150max 150max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 160max 120max 120max 150max 150max 150max 150max 200max 160max 160max 180max 180max 180max 180max 240max 40max 50max 75max 120max 150max 240max 360max 60max 75max 120max 180max 180max 290max 440max 12max 20max 30max 48max 60max 96max 144max 400typ(ACIN 100/200V, Io=100%) *Start-up time is 500ms typ for less than 1minute of applying input again from turning off 20typ (ACIN 100/200V, Io=100%) 2.64 - 3.96 3.96 - 6.00 5.25 - 8.25 8.25 - 13.20 10.50 - 16.50 16.50 - 26.40 25.20 - 39.60 3.30 - 3.40 5.00 - 5.15 7.50 - 7.80 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 Works over 105% of rated current or 101% of peak current and recovers automatically Vo+0.66 - 1.32 Vo+1.0 - 2.0 Vo+1.5 - 3.0 Vo+2.4 - 4.8 Vo+3.0 - 6.0 Vo+4.8 - 9.6 Vo+7.2 - 14.4 LED (Green) Provided Provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -20 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *7 120X61X190mm [4.72X2.4X7.48 inches] (without terminal block and screw) (W XHXD) /1.6kg max Forced cooling (internal fan) *1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3 () means peak current. Peak loading for 10s. And Duty 35% max, refer to Instruction manual in detail. *4 Overvoltage protection circuit to follow to output voltage setting. Standard overvoltage protection circuit is please contact us for details. PBA/PBW-18 *5 *6 *7 * Derating is required.Consult us for details. Please contact us about safety approvals for the model with option. Please contact us about class C. A sound may occur from power supply at pulse loading. PBA600F-48 81typ 83typ 48 13 13 192max 300max 150max 400max 200max 500max 480max 600max 192max the input voltage. 38.40 - 56.00 48.00 - 49.92 Vo+4.8 - 12.0 PBA600F Block diagram PBA/PBW FUSE AC IN 85 - 264V NOISE FILTER 250V15A INRUSH CURRENT LIMIT RECTIFIER FG RECTIFIER AND FILTER INVERTER DC OUT ±M THERMAL PROTECTION CURRENT SENSING OVER VOLTAGE PROTECTION ACTIVE FILTER RECTIFIER AND FILTER SWITCHING DEVICE CONTROL CONTROL ±S(REMOTE SENSING) RC(REMOTE ON / OFF) VOLTAGE SENSING MASTER SLAVE CONTROL CURRENT SENSING VOLTAGE SENSING CONTROL INTERNAL REGULATOR FAN VB(VOLTAGE BALANCE) CB(CURRENT BALANCE) PG(POWER GOOD) ALARM AUX(12 V 0.1A) External view Name plate [0.94] [1.91] 10 [0.39] 190 ¶1(F1:190.5) 6max [7.48] [0.24] 120 8-M4 Mounting Hole (Both sides) 61 [2.4] ¶ Tolerance : ±1 [±0.04] ¶ Weight : 1.6kg max ¶ PCB Material/thickness : FR-4 / 1.6mm [0.06] ¶ Chassis material : Aluminum 24 ¶ Dimensions in mm, [ ]= inches [0.94] ¶ Mounting torque : 1.2N · m(12.8kgf·cm)max ¶ Screw tightening torque : M4 1.6N • m(16.9kgf • cm)max M5 2.5N • m(24.5kgf • cm)max ¶ The housing for the remote sensing unused is mounted on CN1 ¶1 F1(Optional):190.5 ¶ Please connect safety ground to FG terminal on the unit. [4.72] 150 ±0.5 [5.91] AIR FLOW 38 ±0.5 24 [0.98] [1.5] (48.5) 25max Output voltage adjustable potentiometer 12.5 [0.71] M5 100 ±0.5 [2.07] (52.5) 14 [0.55] [1.08] 14 17 [3.64] [0.34] Output terminal cover (18) [0.49] Output terminal(+) [0.55] [0.67] CN1 LED 27.5 CN2 CN3 CN2 CN1 (92.5) CN3 Output terminal(-) 4-M4 Mounting Hole (Bottom sides) Name plate [0.79] 8.7 ) (6) AC (N) FG FG( [0.24] AC (L) AC(L) AC(N) 10 7 [0.54] [3.94] Input terminal cover 20max M4 [0.39][0.28] (13.8) 150 ±0.5 [5.91] PBA/PBW-19 Ordering information AC-DC Power Supplies Enclosed type PBA1000F PBA/PBW PB 1 A 2 1000 3 F 4 Recommended EMI/EMC Filter NAC-20-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *6 C :with Coating G :Low leakage current U :Operation stop voltage is set at a lower value F1 :With Long-Life fan F3 :Reverse air exhaust type F4 :Low speed fan Refer to instruction manual 7.1. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA1000F-3R3 660 ACIN 100V 3.3V 200A ACIN 200V *3 3.3V 200A PBA1000F-5 1000 5V 200A 5V 200A PBA1000F-7R5 1005 7.5V 134A 7.5V 134A PBA1000F-12 1056 12V 88A 12V 88A PBA1000F-15 1050 15V 70A 15V 70A PBA1000F-24 1056 24V 44A 24V 44(51)A PBA1000F-36 1044 36V 29A 36V 29A PBA1000F-48 1056 48V 22A 48V 22A PBA1000F-3R3 PBA1000F-5 PBA1000F-7R5 PBA1000F-12 PBA1000F-15 PBA1000F-24 PBA1000F-36 AC85 - 264 1f or DC120 - 350 (AC50 or DC70 Please refer to the instruction manual 7. option *5) 9typ 13typ 5typ 7typ 50/60 (47 - 63) 74typ 79typ 80typ 82typ 82typ 84typ 84typ 76typ 81typ 83typ 84typ 84typ 86typ 86typ 0.98typ (Io=100%) 0.95typ (Io=100%) 20/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 10 sec. to re-start) 40/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 10 sec. to re-start) 0.5/1.0max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1, DENAN) 3.3 5 7.5 12 15 24 36 200 200 134 88 70 44 29 200 200 134 88 70 44(51) 29 20max 20max 36max 48max 60max 96max 144max 40max 40max 60max 100max 120max 150max 150max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 160max 120max 120max 150max 150max 150max 150max 200max 160max 160max 180max 180max 180max 180max 240max 40max 50max 75max 120max 150max 240max 360max 60max 75max 120max 180max 180max 290max 440max 12max 20max 30max 48max 60max 96max 144max 400typ(ACIN 100/200V, Io=100%) *Start-up time is 500ms typ for less than 1minute of applying input again from turning off 20typ (ACIN 100/200V, Io=100%) 2.64 - 3.96 3.96 - 6.00 5.25 - 8.25 8.25 - 13.20 10.50 - 16.50 16.50 - 26.40 25.20 - 39.60 3.30 - 3.40 5.00 - 5.15 7.50 - 7.80 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 Works over 105% of rated current or 101% of peak current and recovers automatically Vo+0.66 - 1.32 Vo+1.0 - 2.0 Vo+1.5 - 3.0 Vo+2.4 - 4.8 Vo+3.0 - 6.0 Vo+4.8 - 9.6 Vo+7.2 - 14.4 LED (Green) Provided Provided AC3,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -20 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 *7 150X61X240mm [5.91X2.4X9.45 inches] (without terminal block and screw) (W XHXD) /2.2kg max Forced cooling (internal fan) PBA1000F-48 SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] ACIN 100V CURRENT[A] ACIN 200V *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -20 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -20 - 0C *1 0 to +50C *1 TEMPERATURE REGULATION[mV] -20 to +50C *1 DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] *4 OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC INPUT-FG OUTPUT-RC-AUX-FG OUTPUT-RC -AUX OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] *1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). Ripple and ripple noise is measured on measuring board with capacitor of 22mF within 150mm from the output terminal. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3 () means peak current. Peak loading for 10s. And Duty 35% max, refer to Instruction manual in detail. PBA/PBW-20 84typ 86typ 48 22 22 192max 300max 150max 400max 200max 500max 480max 600max 192max the input voltage. 38.40 - 56.00 48.00 - 49.92 Vo+4.8 - 12.0 *4 Overvoltage protection circuit to follow to output voltage setting. Standard overvoltage protection circuit is please contact us for details. *5 Derating is required.Consult us for details. *6 Please contact us about safety approvals for the model with option. *7 Please contact us about class C. * A sound may occur from power supply at pulse loading. PBA1000F Block diagram PBA/PBW FUSE AC IN 85 - 264V NOISE FILTER 250V30A INRUSH CURRENT LIMIT RECTIFIER FG RECTIFIER AND FILTER INVERTER DC OUT ±M THERMAL PROTECTION CURRENT SENSING OVER VOLTAGE PROTECTION ACTIVE FILTER RECTIFIER AND FILTER SWITCHING DEVICE CONTROL CONTROL ±S(REMOTE SENSING) RC(REMOTE ON / OFF) VOLTAGE SENSING MASTER SLAVE CONTROL CURRENT SENSING VOLTAGE SENSING CONTROL INTERNAL REGULATOR FAN VB(VOLTAGE BALANCE) CB(CURRENT BALANCE) PG(POWER GOOD) ALARM AUX(12 V 0.1A) External view [5.91] 20 [4.12] [0.79] [0.1] Output terminal(+) 2.5 Output terminal(-) 110±0.5 104.75 (24) [0.94] CN1 H V.ADJ CN2 CN3 Output voltage adjustable potentiometer LED Name plate 150 [0.98] 79 FG CN3 CN2 CN1 25max [4.33] Input terminal cover [3.11] 13 9 (7.5) AC (N) [0.51][0.35] [0.3] AC (L) AC(L) AC(N) FG( ) 10 [0.62] 4-M4 Mounting Hole (Bottom sides) Name plate [0.39] M4 15.85 51.25 29 [2.02] (35) [1.14] [1.38] 165 ±0.5 [6.5] 240 6max [9.45] [0.24] 8-M4 Mounting Hole (Both sides) 2-M4 2-º9 [6.5] [2.4] 61 38±0.5 165±0.5 [1.5] 29 [1.14] 11.5 ¶ Tolerance : ±1 [±0.04] 7 13 ¶ Weight : 2.2kg max [0.28] [0.51] ¶ PCB Material/thickness : FR-4 / 1.6mm [0.06] ¶ Chassis material : Aluminum ]= inches ¶ Dimensions in mm, [ ¶ Mounting torque : 1.2N • m(12.8kgf • cm)max ¶ Screw tightening torque : 1.6N • m(16.9kgf • cm)max ¶ The housing for the remote sensing unused is mounted on CN1 ¶ Please connect safety ground to FG terminal on the unit. AIR FLOW [0.45] [0.71] [0.98] (18) (25) [0.35] PBA/PBW-21 Ordering information AC-DC Power Supplies Enclosed type PBA1500F PBA/PBW PB 1 A 2 1500 3 F 4 Recommended EMI/EMC Filter NAC-20-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended *to connect with several devices. -5 5 -O 6 1Series name 2Single output 3Output wattage 4Universal input 5Output voltage 6Optional *6 C :with Coating G :Low leakage current U :Operation stop voltage is set at a lower value F1 :With Long-Life fan F3 :Reverse air exhaust type F4 :Low speed fan Refer to instruction manual 7.1. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA1500F-3R3 990 ACIN 100V 3.3V 300A ACIN 200V *3 3.3V 300A PBA1500F-5 1500 5V 300A 5V 300A PBA1500F-7R5 1500 7.5V 200A 7.5V 200A PBA1500F-12 1500 12V 125A 12V 125A PBA1500F-15 1500 15V 100A 15V 100A PBA1500F-24 1680 24V 65A 24V 70(105)A PBA1500F-36 1692 36V 42A 36V 47(70)A PBA1500F-48 1680 48V 32A 48V 35A PBA1500F-3R3 PBA1500F-5 PBA1500F-7R5 PBA1500F-12 PBA1500F-15 PBA1500F-24 PBA1500F-36 AC85 - 264 1f or DC120 - 370 (AC50 or DC70 Please refer to the instruction manual 7. option *5) 15typ 19typ 8typ 10typ 50/60 (47 - 63) 72typ 77typ 81typ 81typ 83typ 84typ 84typ 75typ 81typ 83typ 84typ 86typ 87typ 87typ 0.98typ (Io=100%) 0.95typ (Io=100%) 20/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More than 10 sec. to re-start) 40/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More than 10 sec. to re-start) 0.9/1.5max (ACIN 100V/240V 60Hz, Io=100%, According to IEC60950-1, DENAN) 3.3 5 7.5 12 15 24 36 300 300 200 125 100 65 42 300 300 200 125 100 70(105) 47(70) 20max 20max 36max 48max 60max 96max 144max 40max 40max 60max 100max 120max 150max 150max 80max 80max 120max 120max 120max 120max 150max 140max 140max 160max 160max 160max 160max 160max 120max 120max 150max 150max 150max 150max 200max 160max 160max 180max 180max 180max 180max 240max 40max 50max 75max 120max 150max 240max 360max 60max 75max 120max 180max 180max 290max 440max 12max 20max 30max 48max 60max 96max 144max 600typ(ACIN 100/200V, Io=100%) 20typ (ACIN 100/200V, Io=100%) 2.64 - 3.96 3.96 - 6.00 5.25 - 8.25 8.25 - 13.20 10.50 - 16.50 16.50 - 26.40 25.20 - 39.60 3.30 - 3.40 5.00 - 5.15 7.50 - 7.80 12.00 - 12.48 15.00 - 15.60 24.00 - 24.96 36.00 - 37.44 Works over 105% of rated current or 101% of peak current and recovers automatically Vo+0.66 - 1.32 Vo+1.0 - 2.0 Vo+1.5 - 3.0 Vo+2.4 - 4.8 Vo+3.0 - 6.0 Vo+4.8 - 9.6 Vo+7.2 - 14.4 LED (Green) Provided Provided AC3,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -20 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B, additional EMI/EMC Filter required for Complies with IEC61000-3-2 *7 178X61X268mm [7.01X2.4X10.55 inches] (without terminal block and screw) (W XHXD) /3.4kg max Forced cooling (internal fan) PBA1500F-48 SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] ACIN 100V CURRENT[A] ACIN 200V *3 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -20 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -20 - 0C *1 0 to +50C *1 TEMPERATURE REGULATION[mV] -20 to +50C *1 DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION[V] *4 OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC INPUT-FG OUTPUT-RC-AUX-FG OUTPUT-RC -AUX OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS (At only AC input) CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] *1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). Ripple and ripple noise is measured on measuring board with capacitor of 22mF within 150mm from the output terminal. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3 () means peak current. Peak loading for 10s. And Duty 35% max, refer to Instruction manual in detail. PBA/PBW-22 84typ 87typ 48 32 35 192max 300max 150max 400max 200max 500max 480max 600max 192max 38.40 - 56.00 48.00 - 49.92 Vo+4.8 - 12.0 meeting class B *4 Overvoltage protection circuit to follow to output voltage setting. Standard overvoltage protection circuit is please contact us for details. *5 Derating is required.Consult us for details. *6 Please contact us about safety approvals for the model with option. *7 Please contact us about class C. * A sound may occur from power supply at pulse loading. PBA1500F Block diagram PBA/PBW FUSE AC IN 85 - 264V NOISE FILTER 250V30A INRUSH CURRENT LIMIT RECTIFIER FG RECTIFIER AND FILTER INVERTER DC OUT ±M THERMAL PROTECTION CURRENT SENSING OVER VOLTAGE PROTECTION ACTIVE FILTER RECTIFIER AND FILTER SWITCHING DEVICE CONTROL CONTROL ±S(REMOTE SENSING) RC(REMOTE ON / OFF) VOLTAGE SENSING MASTER SLAVE CONTROL CURRENT SENSING VOLTAGE SENSING CONTROL INTERNAL REGULATOR FAN VB(VOLTAGE BALANCE) CB(CURRENT BALANCE) PG(POWER GOOD) ALARM AUX(12 V 0.1A) CN1 CN2 CN3 [7.01] V.ADJ 178 Name plate [6] 152.4 ±0.5 [5.2] 132 [0.5] 8-M4 Mounting Hole (Both sides) 25max [0.98] 107 (7.5) 10 FG [0.39] NC ) CN1 CN2 CN3 Input terminal cover [4.21] AC (N) FG( AC (L) AC(L) AC(N) NC Name plate 13 9 [0.62] [0.51][0.35] [0.3] M4 15.85 12.8 External view [0.16] 4 (24) LED Output terminal(-) [0.94] Output voltage adjustable potentiometer Output terminal(+) 51.25 19 [2.02] (45) [0.75] [1.77] 171.5 ±0.5 [6.75] 268 6max [10.55] [0.24] 8-M4 Mounting Hole (Both sides) 4-M4 2-º9 [6.75] [2.4] 61 38 ±0.5 171.5 ±0.5 [1.5] 19 [0.75] 11.5 ¶ Tolerance : ±1 [±0.04] 10 15 ¶ Weight : 3.4kg max [0.39] [0.59] ¶ PCB Material/thickness : FR-4 / 1.6mm [0.06] ¶ Chassis material : Aluminum ¶ Dimensions in mm, [ ]= inches ¶ Mounting torque : 1.2N • m(12.8kgf • cm)max ¶ Screw tightening torque : 1.6N • m(16.9kgf • cm)max ¶ The housing for the remote sensing unused is mounted on CN1 ¶ Please connect safety ground to FG terminal on the unit. AIR FLOW [0.45] [0.71] [0.98] (18) (25) [0.35] PBA/PBW-23 Ordering information AC-DC Power Supplies Enclosed type PBA1500T PBA/PBW PB 1 A 1500 2 3 T 4 Recommended EMI/EMC Filter TAC-10-683 R -5 5 -O 6 1Series name 2Single output 3Output wattage 4Triple input phase 5Output voltage 6Optional *6 C :with Coating G :Low leakage current U :Operation stop voltage is set at a lower value F1 :With Long-Life fan F3 :Reverse air exhaust type F4 :Low speed fan Refer to instruction manual 7.1. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT PBA1500T-24 1680 24V 70(105)A PBA1500T-48 1680 48V 35A PBA1500T-12 PBA1500T-24 AC170 - 264 3f (AC100 Please refer to the instruction manual 7. option *5) ACIN 200V 6typ 50/60 (47 - 63) PBA1500T-48 ACIN 200V *3 PBA1500T-5 1500 5V 300A PBA1500T-12 1500 12V 125A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] FREQUENCY[Hz] INPUT PBA1500T-5 84typ ACIN 200V 81typ 87typ 87typ ACIN 200V 0.95typ (Io=100%) INRUSH CURRENT[A] ACIN 200V 40/40typ (Io=100%) (Primary inrush current /Secondary inrush current) (More than 10 sec. to re-start) LEAKAGE CURRENT[mA] 1.5max (ACIN 240V 60Hz, Io=100%, According to IEC60950-1, DENAN) EFFICIENCY[%] POWER FACTOR VOLTAGE[V] CURRENT[A] OUTPUT 5 ACIN 200V *3 300 12 24 48 125 35 300max LINE REGULATION[mV] 20max 48max 70(105) 96max LOAD REGULATION[mV] 0 to +50C *1 RIPPLE[mVp-p] -20 - 0C *1 0 to +50C *1 RIPPLE NOISE[mVp-p] -20 - 0C *1 0 to +50C *1 TEMPERATURE REGULATION[mV] -20 to +50C *1 40max 100max 150max DRIFT[mV] *2 START-UP TIME[ms] HOLD-UP TIME[ms] 80max 120max 120max 150max 140max 160max 160max 400max 120max 150max 150max 200max 160max 180max 180max 500max 50max 120max 240max 480max 75max 180max 290max 600max 20max 48max 96max 192max 300typ(ACIN 200V, Io=100%) *Start-up time is 500ms typ for less than 1 minute of applying input again from turning off the input voltage. 20typ (ACIN 200V, Io=100%) OUTPUT VOLTAGE ADJUSTMENT RANGE[V] 3.96 - 6.00 OUTPUT VOLTAGE SETTING[V] 5.00 - 5.15 8.25 - 13.20 16.50 - 26.40 38.40 - 56.00 12.00 - 12.48 24.00 - 24.96 48.00 - 49.92 OVERCURRENT PROTECTION Works over 105% of rated current or 101% of peak current and recovers automatically Vo+4.8 - 9.6 4 Vo+2.4 - 4.8 PROTECTION OVERVOLTAGE PROTECTION[V] * Vo+1.0 - 2.0 CIRCUIT AND OPERATING INDICATION LED (Green) OTHERS Provided REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT -RC ISOLATION INPUT-FG OUTPUT-RC-AUX-FG OUTPUT-RC -AUX OPERATING TEMP.,HUMID.AND ALTITUDE 192max Vo+2.0 - 12.0 Provided AC3,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC2,000V 1minute, Cutoff current = 25mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MWmin (At Room Temperature) -20 to +71C (Required Derating), 20 - 90%RH (Non condensing) 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing) 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis SAFETY AND AGENCY APPROVALS (At only AC input) UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN NOISE Complies with FCC Part15 classB, VCCI-B, CISPR22-B, EN55011-B, EN55022-B, additional EMI/EMC Filter required for meeting class B REGULATIONS CONDUCTED NOISE 178X61X268mm [7.01X2.4X10.55 inches] (without terminal block and screw) (W XHXD) /3.4kg max CASE SIZE/WEIGHT OTHERS COOLING METHOD Forced cooling (internal fan) ENVIRONMENT STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION *1 Measured by 20MHz oscilloscope or Ripple-Noise meter(equivalent to KEISOKU-GIKEN :RM101). Ripple and ripple noise is measured on measuring board with capacitor of 22mF within 150mm from the output terminal. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C. *3 () means peak current. Peak loading for 10s. And Duty 35% max, refer to Instruction manual in detail. PBA/PBW-24 *4 Overvoltage protection circuit to follow to output voltage setting. Standard overvoltage protection circuit is please contact us for details. *5 Derating is required.Consult us for details. *6 Please contact us about safety approvals for the model with option. * A sound may occur from power supply at pulse loading. PBA1500T Block diagram PBA/PBW FUSE AC250V16A AC IN 170 - 264V (3º) NOISE FILTER INRUSH CURRENT LIMIT RECTIFIER FG RECTIFIER AND FILTER INVERTER DC OUT ±M(MONITOR) THERMAL PROTECTION CURRENT SENSING OVER VOLTAGE PROTECTION ACTIVE FILTER RECTIFIER AND FILTER SWITCHING DEVICE CONTROL CONTROL ±S(REMOTE SENSING) RC(REMOTE ON / OFF) VOLTAGE SENSING MASTER SLAVE CONTROL CURRENT SENSING VOLTAGE SENSING CONTROL INTERNAL REGULATOR FAN VB(VOLTAGE BALANCE) CB(CURRENT BALANCE) PG(POWER GOOD) ALARM AUX(12 V 0.1A) OPEN PHASE CN1 CN2 CN3 [7.01] V.ADJ 178 Name plate [6] 152.4 ±0.5 [5.2] 132 12.8 8-M4 Mounting Hole (Both sides) 25max [0.98] 107 (7.5) 10 FG [0.39] (L3) ) CN1 CN2 CN3 Input terminal cover [4.21] AC (L2) FG( (L1) AC(L1) AC(L2) AC(L3) Name plate 13 9 [0.62] [0.51][0.35] [0.3] M4 15.85 [0.5] External view [0.16] 4 (24) LED Output terminal(-) [0.94] Output voltage adjustable potentiometer Output terminal(+) 51.25 19 [2.02] (45) [0.75] [1.77] 171.5 ±0.5 [6.75] 268 6max [10.55] [0.24] 8-M4 Mounting Hole (Both sides) 4-M4 2-º9 [6.75] [2.4] 61 38 ±0.5 171.5 ±0.5 [1.5] 19 [0.75] 11.5 ¶ Tolerance : ±1 [±0.04] 10 15 ¶ Weight : 3.4kg max [0.39] [0.59] ¶ PCB Material/thickness : FR-4 / 1.6mm [0.06] ¶ Chassis material : Aluminum ¶ Dimensions in mm, [ ]= inches ¶ Mounting torque : 1.2N • m(12.8kgf • cm)max ¶ Screw tightening torque : 1.6N • m(16.9kgf • cm)max ¶ The housing for the remote sensing unused is mounted on CN1 ¶ Please connect safety ground to unit in M4 holes. AIR FLOW [0.45] [0.71] [0.98] (18) (25) [0.35] PBA/PBW-25