TECH. CORP. SPECIFICATIONS CUSTOMER : CTW1304 SAMPLE CODE : SE12832LRF-002HL1Q MASS PRODUCTION CODE : PE12832LRF-002HL1Q SAMPLE VERSION : 01 SPECIFICATIONS EDITION : 002 DRAWING NO. (Ver.) : JLMD- PE12832LRF-002HL1Q _001 PACKAGING NO. (Ver.) : JPKG- PE12832LRF-002HL1Q _001 Customer Approved POWERTIP 2011.04.01 Date: JS RD APPROVED Approved Checked Designer 閆偉 Ryan Yan 劉進 Lori Liu 黃小琴 Violin Huang □ Preliminary specification for design input ■ Specification for sample approval POWERTIP TECH. CORP. Headquarters: th No.8, 6 Road, Taichung Industrial Park, TEL: 886-4-2355-8168 E-mail: [email protected] FAX: 886-4-2355-8166 Http://www.powertip.com.tw Taichung, Taiwan 台中市 407 工業區六路 8 號 NO.PT-A-005-8 History of Version Date (mm / dd / yyyy) Ver. Edi. Description 09/18/2011 0 Mass production Changed the backlight’s resister is 75ohm based 001 on the Powertip’s mass production: PE12832LRF-002-H-Q 3/28/2011 01 002 The second sample with second sourse’s FPC Page Design by - 匡唐忠 - Violin Total:page 27 PE12832LRF-002HL1Q Page2 SAMPLE Ver.01 SPEC Edi.002 Contents 1. SPECIFICATIONS 1.1 1.2 1.3 1.4 1.5 1.6 Features Mechanical Specifications Absolute Maximum Ratings DC Electrical Characteristics Optical Characteristics Backlight Characteristics 2. MODULE STRUCTURE 2.1 Counter Drawing 2.2 Interface Pin Description 2.3 Timing Characteristics 2.4 Display Command 3. QUALITY ASSURANCE SYSTEM 3.1 3.2 Quality Assurance Flow Chart Inspection Specification 4. RELIABILITY TEST 4.1 Reliability Test Condition 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 Safety 5.2 Handling 5.3 Storage 5.4 Terms of Warranty Appendix: PE12832LRF-002HL1Q 1. LCM Drawing 2. Packaging Specification Page3 SAMPLE Ver.01 SPEC Edi.002 1. SPECIFICATIONS 1.1 Features Item Standard Value Display Type 128 * 32 Dots LCD Type FSTN , Positive, Transflective Driver Condition LCD Module:1/33 Duty, 1/6 Bias, Viewing Direction 6 O’clock Backlight Yellow Green Backlight Weight 2.7g Interface Parallel Interface Other (controller / driver IC) Stronix – ST7565R-G ROHS THIS PRODUCT CONFORMS THE ROHS OF PTC Detail information please refer web side: http://www.powertip.com.tw/news.php?area_id_view=1085560481/ 1.2 Mechanical Specifications Item Standard Value Unit Outline Dimension 38.8 (W) *17.65(L) * 3.05 (H) mm Viewing Area 32.0 (W) * 8.9 (L) mm Active Area 26.86 (W) * 7.34 (L) mm Dot Size 0.19 (W) * 0.21 (H) mm Dot Pitch 0.21 (W) * 0.23 (H) mm Note:For detailed information please refer to LCM drawing 1.3 Absolute Maximum Ratings Item Symbol Condition Min. Max. Unit Power Supply Voltage VDD - -0.3 3.6 V LCD Driver Supply Voltage VLCD - -0.3 13.5 V Input Voltage VIN - -0.3 VDD+0.5 V Operating Temperature TOP - -20 70 ℃ Storage Temperature TST - -30 80 ℃ Humiduty HD Ta<40℃ 20 90 %RH PE12832LRF-002HL1Q Page4 SAMPLE Ver.01 SPEC Edi.002 1.4 DC Electrical Characteristics VDD = 3.0±0.3V, VSS = 0V, Ta = 25°C Module Item Symbol Condition Min. Typ. Max. Unit Logic Supply Voltage VDD - 2.7 3.0 3.3 V Input High Voltage VIH - 0.8 VDD - VDD V Input Low Voltage VIL - VSS - 0.2 VDD V Output High Voltage VOH - 0.8 VDD - VDD V Output Low Voltage VOL - VSS - 0.2 VDD V Supply Current IDD - 0.08 0.15 mA -20℃ 5.3 5.5 5.7 25℃ 5.0 5.2 5.4 70℃ 4.5 4.7 4.9 VDD =3.0 V;Vop=5.2 V Pattern= horizontal*1 VOP LCM Driver Voltage *2 V NOTE:*1 The Maximum current display. *2 The VOP test point is V0-VSS. PE12832LRF-002HL1Q Page5 SAMPLE Ver.01 SPEC Edi.002 1.5 Optical Characteristics LCD Panel:Duty=1/33,Bias=1/6,VOP=5.36V,Ta =25℃ Item Symbol Min. Typ. Max. Unit Reference ms Note 2 Deg. Note 1 Rise Tr - 80 120 Fall Tf - 180 270 Top ΘY+ - - 40 Bottom ΘY- - - 40 Left ΘX- - - 40 Right ΘX+ - - 40 1.5 2.0 - - Note 3 3 10 - cd/m2 - 569 - 578 nm - 70 - - % - Response Time Viewing angle range Conditions Contrast Ratio (With BL) CR Average Brightness (With LCD) *2 IV CIE Color Coordinate (With LCD) *2 Hue Uniformity *1 △B C>2.0, ∅ = 270 ゚ θ = 0°, ∅ = 270 ゚ IF=10 mA - Note: *1:△B=B(min) / B(max) * 100% *2:Measurement Condition for Optical Characteristics: a:Environment: 25℃±5℃ / 60±20%R.H,no wind,dark room below 10 Lux at typical lamp current and typical operating frequency. b:Measurement Distance: 500 ± 50 ㎜ ,(θ= 0°) c:Equipment: TOPCON BM-7 fast,(field 0.2°),after 10 minutes operation. d:The uncertainty of the C.I.E coordinate measurement ±0.01,Average Brightness ± 4% 1 2 3 VIEW AREA 6 5 4 7 8 θθ 9 500 ㎜ LCM Colorimeter=BM-7 fast PE12832LRF-002HL1Q Page6 SAMPLE Ver.01 SPEC Edi.002 Note 1. Optical characteristics-2 Viewing angle Rear (12H) φ=90° Top (θ=0°) θL θR θ+ θ- Left (9H) φ=180° Right (3H) φ =0° Front (6H) φ=270° Viewing angle PE12832LRF-002HL1Q Page7 SAMPLE Ver.01 SPEC Edi.002 Note 2. Optical characteristics-3 Fig.2 Definition of response time Positive Type No selected waveform No selected waveform Selected waveform Transmittance 10% 90% 100% Tf Tr Negative Type No selected waveform No selected Selected waveform Transmittance 100% 90% 10% Tr PE12832LRF-002HL1Q Tf Page8 SAMPLE Ver.01 SPEC Edi.002 Electrical characteristics-2 ※2 Drive waveform Vop: Drive voltage 1/B: Bias N: Duty fF: Frame frequency fD: Drive frequency (1) Selected waveform 1 2 3 N 1 3 2 V Vop/B Vop/B V 1/fD 1/fF (2) Non- Selected wave form 1 2 3 N 1 2 3 (1-2/B)Vop Vop/B Vop/ (1-2/B)Vop 1/fF 1/fD Note: Frame frequency is defined as follows: Common side supply voltage peak - to - peak /2 = 1 period PE12832LRF-002HL1Q Page9 SAMPLE Ver.01 SPEC Edi.002 Note 3. : Definition of Vth Selected waveform 100 73% Transmittanc No selected waveform 50% Vth1 Vth2 Drive Active voltage range View direction Drive waveform Transmittance Vth1 10° (Selected waveform) 50% Vth2 40° (No selected waveform) 73% ※1 Contrast ratio = (Brightness in OFF state) / (Brightness in ON state) Outline of Electro-Optical Characteristics Measuring System Photo Detector θ Human Active ψ Temperatur e Control Chamber LCD Panel Transmissive Measuring System: Autronic DMS-803 PE12832LRF-002HL1Q Page10 SAMPLE Ver.01 SPEC Edi.002 LCD Module with LED Backlight Maximum Ratings Item Symbol Conditions Spec Unit Forward Current IF Ta =25°C 20 mA Reverse Voltage VR Ta =25°C 5 V Electrical / Optical Characteristics Item Symbol Forward Voltage VF Conditions Typ. Max. Unit 2.6 2.8 3.0 V 8 12 - cd/m2 - - 100 μA IF= 10 mA Average Brightness (without LCD) IV Reverse Current IR VR= 3 V Color PE12832LRF-002HL1Q Min. Yellow Green Page11 SAMPLE Ver.01 SPEC Edi.002 2. MODULE STRUCTURE 2.1 Counter Drawing 2.1.1 LCM Mechanical Diagram * See Appendix 2.1.2 Block Diagram K A LED BACKLIGHT K A 128*32 DOTS 16 COM16 ………… COM15 ………… COM31 16 COM0 ………… SEG0 SEG127 128 ………… ………… SEG127 COM48 ST-7565R COM15 PIN1 ………… SEG0 COM0 COM63 ……………………………… PIN28 Please refer interface pin description for detail PE12832LRF-002HL1Q Page12 SAMPLE Ver.01 SPEC Edi.002 2.2 Interface Pin Description Pin No. Symbol Function 1 VDD Shared with the MPU power supply terminal Vcc. 2 C86 This is the MPU interface switch terminal. C86 = “H”: 6800 Series MPU interface. C86 = “L”: 8080 MPU interface. 3 NC NC. 4 V0 This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using 5 V1 6 V2 7 V3 8 V4 9 CAP2N DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2P terminal. 10 CAP2P DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2N terminal. 11 CAP1P DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 12 CAP1N DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1P terminal. 13 CAP3P DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1N terminal. 14 VOUT DC/DC voltage converter. Connect a capacitor between this terminal and VSS. 15 VSS 16 D7 17 D6 18 D5 19 D4 PE12832LRF-002HL1Q an op. amp. Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below. V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧ Vss When the power supply turns ON, the internal power supply circuits produce the V1 to V4 voltages shown below. The voltage settings are selected using the LCD bias set command . This is the reference power supply for the step-up voltage circuit for the liquid crystal drive. This is an 8-bit bi-directional data bus that connects to an 8-bit or16-bit standard MPU data bus. Page13 SAMPLE Ver.01 SPEC Edi.002 20 D3 21 D2 22 D1 23 D0 24 /RD(E) • When connected to an 8080 MPU, this is active LOW. (E) This pin is connected to the /RD signal of the 8080 MPU, and the ST7565S series data bus is in an output status when this signal is “L”. • When connected to a 6800 Series MPU, this is active HIGH. This is the 6800 Series MPU enable clock input terminal. • When connected to an 8080 MPU, this is active LOW. (R/W) This terminal connects to the 8080 MPU /WR signal. The 25 /WR(R/W) signals on the data bus are latched at the rising edge of the /WR signal. • When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write. This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or a command. A0 = “H”: Indicates that D0 to D7 are display data. A0 = “L”: Indicates that D0 to D7 are control data. 26 A0 27 /RES When /RES is set to “L,” the settings are initialized. The reset operation is performed by the /RES signal level. 28 /CS1 Chip Select signal. Active “L”. PE12832LRF-002HL1Q Page14 SAMPLE Ver.01 SPEC Edi.002 2.3 Timing Characteristics 8080 INTERFACE PE12832LRF-002HL1Q Page15 SAMPLE Ver.01 SPEC Edi.002 6800 INTERFACE PE12832LRF-002HL1Q Page16 SAMPLE Ver.01 SPEC Edi.002 2.4 Display Command PE12832LRF-002HL1Q Page17 SAMPLE Ver.01 SPEC Edi.002 3. QUALITY ASSURANCE SYSTEM 3.1 Quality Assurance Flow Chart Item Customer Sales Info Marketing & Design R&D Manufactu Product Inventory Purchase ring control control Q.A Survey Request Project Inquiry evaluation Project Validation NG OK Quote Contract Design check Sample test Sample Approval NG Verification NG OK Sample approval OK Pilot Pilot Run & Mass Product NG Verification OK Specification preparation Mass production OK Ship Out PE12832LRF-002HL1Q run & Reliability test Inspection NG Shipment Ship out Page18 SAMPLE Ver.01 SPEC Edi.002 Item Customer Sales Info Claim R&D Q.A Manufact Product Inventory Purchase uring control control Failure analysis Sales Service Analysis report Corrective action Tracking 1. ISO 9001 Maintenance Activities Q.A 3. Equipment calibration Activity 5. Standardization Management PE12832LRF-002HL1Q Page19 2. Process improvement proposal 4. Education And Training Activities SAMPLE Ver.01 SPEC Edi.002 3.2. Inspection Specification PE12832LRF-002HL1Q Page20 SAMPLE Ver.01 SPEC Edi.002 PE12832LRF-002HL1Q Page21 SAMPLE Ver.01 SPEC Edi.002 PE12832LRF-002HL1Q Page22 SAMPLE Ver.01 SPEC Edi.002 PE12832LRF-002HL1Q Page23 SAMPLE Ver.01 SPEC Edi.002 PE12832LRF-002HL1Q Page24 SAMPLE Ver.01 SPEC Edi.002 PE12832LRF-002HL1Q Page25 SAMPLE Ver.01 SPEC Edi.002 4. RELIABILITY TEST 4.1 Reliability Test Condition NO. TEST ITEM 1 High Temperature Storage Test 2 Low Temperature Storage Test 3 High Temperature / High Humidity Storage Test 4 Temperature Cycling Storage Test 5 ESD Test 6 Vibration Test (Packaged) 7 Drop Test (Packaged) (Ver.B01) TEST CONDITION Keep in +80℃ ±2℃ 96 hrs Surrounding temperature, then storage at normal condition 4hrs. Keep in -30℃ ±2℃ 96 hrs Surrounding temperature, then storage at normal condition 4hrs. Keep in +60℃ / 90% R.H duration for 96 hrs Surrounding temperature, then storage at normal condition 4hrs. (Excluding the polarizer) -30℃→ +25℃℃→ +80℃→ +25℃ (30mins) (5mins) (30mins) (5mins) 10 Cycle Surrounding temperature, then storage at normal condition 4hrs. Air Discharge: Contact Discharge: Apply 2 KV with 5 times Apply 250 V with 5 times Discharge for each polarity +/discharge for each polarity +/1. Temperature ambiance : 15℃~35℃ 2. Humidity relative : 30%~60% 3. Energy Storage Capacitance(Cs+Cd) : 150pF±10% 4. Discharge Resistance(Rd) : 330Ω±10% 5. Discharge, mode of operation : Single Discharge (time between successive discharges at least 1 sec) (Tolerance if the output voltage indication : ±5%) 1. Sine wave 10~55 Hz frequency (1 min/sweep) 2. The amplitude of vibration :1.5 mm 3. Each direction (X、Y、Z) duration for 2 Hrs Packing Weight (Kg) 0 ~ 45.4 Drop Height (cm) 122 45.4 ~ 90.8 76 90.8 ~ 454 61 Over 454 46 Drop Direction :※1 corner / 3 edges / 6 sides each 1time PE12832LRF-002HL1Q Page26 SAMPLE Ver.01 SPEC Edi.002 5. PRECAUTION RELATING PRODUCT HANDLING 5.1 SAFETY 5.1.1 5.1.2 If the LCD panel breaks, be careful not to get the liquid crystal to touch your skin. If the liquid crystal touches your skin or clothes, please wash it off immediately by using soap and water. 5.2 HANDLING 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 Avoid any strong mechanical shock which can break the glass. Avoid static electricity which can damage the CMOS LSI—When working with the module , be sure to ground your body and any electrical equipment you may be using. Do not remove the panel or frame from the module. The polarizing plate of the display is very fragile. So, please handle it very carefully, do not touch , push or rub the exposed polarizing with anything harder than an HB pencil lead (glass , tweezers , etc.) Do not wipe the polarizing plate with a dry cloth, as it may easily scratch the surface of plate. Do not touch the display area with bare hands, this will stain the display area. Do not use ketonics solvent & aromatic solvent. Use with a soft cloth soaked with a cleaning naphtha solvent. To control temperature and time of soldering is 320 ± 10°C and 3-5 sec. To avoid liquid (include organic solvent) stained on LCM 5.3 STORAGE 5.3.1 5.3.2 5.3.3 Store the panel or module in a dark place where the temperature is 25°C ± 5°C and the humidity is below 65% RH. Do not place the module near organics solvents or corrosive gases. Do not crush, shake, or jolt the module. 5.4 TERMS OF WARRANTY 5.4.1 5.4.2 Applicable warrant period The period is within thirteen months since the date of shipping out under normal using and storage conditions. Unaccepted responsibility This product has been manufactured to your company’s specification as a part for use in your company’s general electronic products. It is guaranteed to perform according to delivery specifications. For any other use apart from general electronic equipment, we cannot take responsibility if the product is used in nuclear power control equipment, aerospace equipment , fire and security systems or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. PE12832LRF-002HL1Q Page27 SAMPLE Ver.01 SPEC Edi.002