ABW-02 SERIES AC/DC Power Module 2W FEATURES ►Fully Encapsulated Plastic Case for PCB Mounting ►Universal Input 85~264VAC, 47~440Hz ►Constant Power Mode, No Output Current Limit ►Protection Class II as per IEC/EN 60536 ►Operating Ambient Temp. Range -30°C to +70°C ►Short Circuit Protection ►Designed-in EMI Emission meets EN55011/22 Class B & FCC Level B ►Designed-in EMC Immunity meets EN61000-4-2,3,4,5,6,8,11 ►Eco Design, Low No Load Power Consumption < 150mW ►UL/cUL/IEC/EN 60950-1, TUV/IEC/EN 60335-1 Safety Approval & CE Marking PRODUCT OVERVIEW The ABW-02 series is a new range of small, fully encapsulated AC/DC power supply modules.They are designed for direct PCB mounting with solder pins.They feature regulated output voltages which have a constant output power mode instead of a conventional current limit characteristics,which makes the power modules suitable to drive relays,solenoids,capacitive loads and LED’s.To power logic circuits for standby functions models with an addtional second, voltage regulated 3.3 or 5VDC output are available. The ABW-02 power supply modules provide a cost-effective new solution for standby power applications in appliances and consumer electronics. equipment. Universal input voltage 85-264VAC and International safety approvals including IEC/EN60335-1 qualifies the product for worldwide markets. Model Selection Guide Model Number Voltage Output 1 ABW-02S08 ABW-02S14 ABW-02S24 ABW-02D83 *** ABW-02D85 *** ABW-02D143 *** ABW-02D145 *** VDC 8 14 24 8 8 14 14 Output 2 Voltage Current Max. mA 250 143 83 * * ** ** Current Max. mA ------160 250 70 83 VDC ------3.3 5 3.3 5 Input Current Efficiency (typ.) @Max. Load mA(typ.) 42 40 39 43 43 43 43 @Max. Load % 72 74 76 69 69 70 70 * Io1+Io2≦250mA ** Io1+Io2≦143mA *** The definition of output power (Po) for dual-output modules : Po=V01 x (I01 + I02 ) Input Specifications Parameter Input Voltage Range Input Frequency Range Input Voltage Range No-Load Power Consumption Input Surge Voltage Model Min. 85 47 120 ----- All Models Typ. ------30 --- Max. 264 440 370 --308 Unit VAC Hz VDC mW VAC Output Specifications Parameter Conditions Output 1 Output Voltage Accuracy Output 2 Output 1 Line Regulation Output 2 Output 1 Load Regulation Output 2 Ripple & Noise 0-20 MHz Bandwidth Short Circuit Protection REV:3 Vin=85~264VAC Io=10% to 100% Typ. Max. Unit --- --- ±5.0 % --- --- ±2.0 % --- ±1.0 --- % --- ±0.3 --- % --- ±1.0 --- % --- ±0.5 --- % Output 1 --- 1 --- V P-P Output 2 --- 0.1 --- V P-P Continuous, Automatic Recovery E-mail:[email protected] 2015/07/31 Vin=115VAC, Full Load Min. Tel:886-6-2923150 Page 1 of 3 ABW-02 SERIES AC/DC POWER MODULE 2W General Specifications Parameter Conditions Min. Typ. Max. Unit Input to Output, 60 Seconds 3000 --- --- VAC --- 45 --- MIL-HDBK-217F@25℃, Ground Benign 500,000 I/O Isolation Voltage Switching Frequency MTBF (calculated) KHz Hours UL/cUL 60950-1 recognition(UL certificate) IEC/EN 60950-1(CB-report) IEC/EN 60335-1 recognition(TUV certificata,CB-report) Safety Approvals Environmental Specifications Parameter Operating Ambient Temperature Range (See Power Derating Curve) Storage Temperature Range Humidity (non condensing) Cooling Conditions Min. Max. Unit Natural Convection -30 +70 ℃ +85 95 ℃ % rel. H 260 ℃ -40 --Natural Convection Lead Temperature (1.5mm from case for 10Sec.) --- EMC Specifications Parameter Standards & Level Conduction and Radiation EN55014-2 ,EN55024 ESD Radiated immunity Fast transient Surge EMI EMS Conducted immunity PFMF Dips Interruptions Performance EN55014-1, EN55022, FCC part 15 Class B EN61000-4-2 Air ± 8kV , Contact ± 4kV EN61000-4-3 10V/m EN61000-4-4 ±2kV EN61000-4-5 ±1kV EN61000-4-6 10Vrms EN61000-4-8 30A/M EN61000-4-11 30% 10ms EN61000-4-11 >95% 5000ms A A A A A A A B Notes 1 2 3 4 5 All specifications typical at Ta=+25℃, resistive load, 115VAC, 60Hz input voltage and after warm-up time rated output current unless otherwise noted. These power modules require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage the power supplies however they may not meet all listed specifications. We recommend to protect the converter by a slow blow fuse in the input supply line. Other input and output voltage may be available, please contact factory. Specifications are subject to change without notice. Typical Constant Power V/I Curve Output Voltage(VDC) 10 8 6 4 2 0 0 100 200 300 400 500 Output Current(mA) E-mail:[email protected] 2015/07/31 REV:3 Tel:886-6-2923150 Page 2 of 3 600 700 800 900 ABW-02 SERIES AC/DC POWER MODULE 2W Package Specifications Pin Connections 2x3.75 [2x0.15] Mechanical Dimensions Single Output Dual Output NC 4 3 +Vout +Vout1 5 4 -Vout Common 5 NP +Vout2 Bottom View 0.80 [0.03] NC 2 34.2 [1.35] 1 3 14.00 [0.55] 25.25 [0.99] 2 Pin 6 AC(N) 7 AC(L) 7.50 [0.30] 6 6.35 [0.25] 1 7 28.4 [1.12] 2.6 [0.10] ►All dimensions in mm 21.00 [0.83] 3.2 [0.13] 14.8 [0.58] ►Tolerance: ±0.5 ►Pin (inches) (±0.01) diameter 0.8 ±0.1 (0.03±0.004) Physical Characteristics Case Size : 34.2x28.4x14.8mm (1.35x1.12x0.58 inches) Case Material : Plastic resin (flammability to UL 94V-0 rated) Pin Material : Copper Alloy with Gold Plate Over Nickel Subplate Weight : 24g Minmax Technology Co., Ltd. 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] 2015/07/31 REV:3 Page 3 of 3