KPC6N136S - COSMO Electronics Corporation

PRODUCT SPECIFICATION
DATE:03/26/2012
cosmo
Photocoupler:
ELECTRONICS CORPORATION
KPC6N136S
NO.61P51001
SHEET 1 OF 5
General Purpose Type Photocoupler
z Features
1. Pb free and RoHS compliant.
2. High speed response tPHL, tPLH
( MAX. 0.8us at RL=1.9KΩ )
3. High common mode rejection voltage
( CMH:TYP. 1KV/us )
4. Compact surface mount type package
5. Agency Approvals
UL approved:UL1577 , No.E169586
CUL approved:C22.2 No.1 & NTC No.5 , No.E169586
VDE approved:EN60747 , No.40006080
FIMKO approved:EN 60065 No. FI 25798
EN 60950 No. FI 25798
z Application:
1. Computers, measuring instruments, control equipment.
2. High speed line receivers, high speed logic.
3. Telephone sets.
4. Signal transmission between circuits of different
Potentials and impedances.
REV.
3
PRODUCT SPECIFICATION
DATE:03/26/2012
Photocoupler:
cosmo
NO.61P51001
KPC6N136S
ELECTRONICS CORPORATION
SHEET 2 OF 5
REV.
3
z Outside Dimension:Unit ( mm )
e
d
o
C
a
t
a
D
o6X
m3
X
s1
X
oN
c6
TOLERANCE:±0.2mm
z Schematic:Top View
5
6
7
8
4
3
2
1
1. NC
2. Anode
3. Cathode
4. NC
5. GND
6. VO
7. VB
8. VCC
PRODUCT SPECIFICATION
DATE:03/26/2012
cosmo
Photocoupler:
ELECTRONICS CORPORATION
z
KPC6N136S
SHEET 3 OF 5
Absolute Maximum Ratings
Parameter
Symbol
Forward current
IF
*1 Peak forward current
IF
Input
*2 Peak transient forward current
IFM
Reverse voltage
VR
Power dissipation
P
Supply voltage
VCC
Output voltage
VO
Emitter-base reverse with stand voltage ( Pin5 to 7 )
VEBO
Output
Average output current
IO
Peak output current
IOP
Base current ( Pin7 )
IB
Power dissipation
PO
*3 Isolation voltage 1 minute
Viso
Operating temperature
Topr
Storage temperature
Tstg
*4 Soldering temperature 10 second
Tsol
*1 50% duty cycle, Pulse width:1mS
Decreases at the rate of 1.6mA/℃ if the external temperature is 70℃ or more.
*2 Pulse width≦1uS, 300pulse/sec
*3 40 to 60% RH, AC for 1 minute
*4 For 10 seconds
z
NO.61P51001
Rating
25
50
1
5
45
-0.5 to 15
-0.5 to 15
5
8
16
5
100
5000
-55 to +100
-55 to +125
260
REV.
3
( Ta=25℃ )
Unit
mA
mA
A
V
mW
V
V
V
mA
mA
mA
mW
Vrms
℃
℃
℃
( Ta=0 to +70℃ unless otherwise specified )
Parameter
Symbol
Conditions
MIN. TYP. MAX. Unit
Ta=25℃, IF=16mA
19
40
%
CTR(1)
VO=0.4V, VCC=4.5V
*5 Current transfer ratio
IF=16mA
CTR(2)
15
43
%
VO=0.5V, VCC=4.5V
Logic ( 0 ) output voltage
VOL
*6 VCC=4.5V, IF=16mA
0.1
0.4
V
Ta=25℃, IF=0
3.0
500
nA
IOH(1)
VO=VCC=5.5V
Logic ( 1 ) output current
Ta=25℃, IF=0
0.01
1.0
uA
IOH(2)
VO=VCC=15V
IOH(3)
VCC=VO=15V, IF=0
50
uA
IF=16mA
200
uA
Logic ( 0 ) supply current
ICCL
VO=open, VCC=15V
Ta=25℃, IO=0
0.02
1.0
uA
ICCH(1)
VF=open, VCC=15V
Logic ( 1 ) supply current
IO=0
2.0
uA
ICCH(2)
VO=open, VCC=15V
Ta=25℃, IF=16mA
1.7
1.95
V
Input forward voltage
VF
mV/℃
Input forward voltage temperature coefficient
△VF/△Ta
IF=16mA
-1.9
Ta=25℃, IR=10uA
5.0
V
Input reverse voltage
BVR
Input capacitance
CIN
VF=0, f=1MHz
60
pF
Ta=25℃, 45%RH
1.0
uA
*7 Leak current ( input-output )
II-O
VI-O=3KVDC, t=5s
Ω
*7 Isolation resistance ( input-output )
RI-O
VI-O=500VDC
1012
*7 Capacitance ( input-output )
CI-O
f=1MHz
0.6
pF
Transistor current amplification factor
hFE
VO=5V, IO=3mA
70
*5 Current transfer ratio is the ratio of input current and output current expressed in %
*6 IO=2.4mA
*7 Measured as 2-pin element ( Short 1, 2, 3, 4 and 5, 6, 7, 8 )
Electro-optical Characteristics
PRODUCT SPECIFICATION
DATE:03/26/2012
Photocoupler:
cosmo
KPC6N136S
ELECTRONICS CORPORATION
z
NO.61P51001
SHEET 4 OF 5
( Ta=25℃, VCC=5V, IF=16mA )
MIN.
TYP. MAX.
Unit
Switching Characteristics
Parameter
Propagation delay time
Output (1) Æ (0)
*8 Propagation delay time
*9 Output (0) Æ (1)
Instantaneous common
*10
*11 mode rejection voltage
“ Output (1) “
Instantaneous common
*10
*11 mode rejection voltage
“ Output (0) “
Symbol
*8
*9
*12
REV.
3
Conditions
tPHL
RL=1.9KΩ
-
0.3
0.8
uS
tPLH
RL=1.9KΩ
-
0.3
0.8
uS
CMH
IF=0, VCM=10VP-P
-
1000
-
V/uS
CML
IF=16mA, VCM=10VP-P
-
-1000
-
V/uS
BW
RL=100Ω
-
2.0
-
MHz
Bandwidth
*8 RL=1.9KΩ is equivalent to one LSTTL and 5.6KΩ pull-up resistor.
*10 Instantaneous common mode rejection voltage “ output (1) “ represents
a common mode voltage variation that can hold the output above (1) level ( Vo > 2.0V )
Instantaneous common mode rejection voltage “ output (0) “ represents
a common mode voltage variation that can hold the output above (0) level ( Vo < 0.8V )
*12 Bandwidth represents a point where AC input goes down by 3dB.
*9 Test Circuit Propagation Delay Time
IF
Pulse input
Duty ratio
= 1/10
0
IF
1
8
2
7
3
6
Vcc
5V
Vo
RL
Vo
1.5V
0.01uF
IF monitor
4
1.5V
C L =15pF
5
100Ω
t PHL
t PLH
*11 Test Circuit for Instantaneous Common Mode Rejection Voltage
10V
IF
8
1
2
7
3
6
B
Vcc=5V
4
5
VFF
VCM
0V
RL
Vo
0.01uF
A
10%
90%
CM H
Vo
10%
90%
tr
tf
5V
IF =0
2V
V CM
+
-
CM L
Vo
0.8V
IF =16mA
VOL
PRODUCT SPECIFICATION
DATE:03/26/2012
cosmo
ELECTRONICS CORPORATION
Photocoupler:
KPC6N136S
NO.61P51001
SHEET 5 OF 5
z Notice
The information contained in this document is intended to be a
general product description and is subject to change without notice.
Please contact cosmo in order to obtain the latest device data sheets
before using any cosmo device. cosmo does not assume any
responsibility for use of any circuitry described. No circuit patent
licenses are implied. This publication is the property of cosmo. No
part of this publication may be reproduced or copied in any form or by
any means, or transferred to any third party without the prior written
consent of cosmo Electronics Corporation.
The devices listed in this document are designed for general
applications only in electronic equipment. No devices shall be
deployed which require higher level of reliability such as:
–
–
–
–
Medical and other life support equipments.
Space application.
Telecommunication equipment ( trunk lines ).
Nuclear power control equipment.
Unless it received prior written approval from cosmo.
cosmo takes no responsibility for damages arise form the
improper usage of our device. Please contact cosmo for further
information regarding the above notices.
REV.
3