OPI150 - OPTEK Technology

Optically Coupled Isolator /
High-Speed Optically Coupled Isolator
OPI150, OPI153, OPI155
Features:
• 50 kV electrical isolation
• Choice of phototransistor or photodarlington output
• High speed >5 MBd (OPI155)
• Hermetically sealed LED and photosensor
• Base contact lead for conventional transistor biasing
• TX and TXV process available (see Hi-Rel section)
Product Photo Here
Description:
Each OPI150 and OPI153 is an optically coupled isolator that contains an infrared emitting diode and a NPN
silicon phototransistor (OPI150) or photodarlington (OPI153), each sealed in an individual hermetically sealed
package. The diode and phototransistor or diode and photodarlington are then optically coupled by means of a
light pipe and mounted in a high dielectric plastic housing. These devices are designed for applications that
require very high isolation between input and output.
The OPI155 is a high-speed optical coupled isolator that contains a high speed monolithic photo-IC comprised of a
photodiode and a DC amplifier that drives an open collector output Schottky transistor. It is optically coupled by
means of an internal light pipe. The LED and sensor are both in separate hermetically sealed packages that are
then mounted in a high dielectric plastic housing. This device is designed for applications that require high speed
and high voltage isolation between the input and output.
TX and TXV devices are available. Please contact your local representative or OPTEK for more information.
Applications:
•
•
•
•
•
Ordering Information
Requiring high voltage isolation
between input and output
Electrical isolation in dirty environments
Industrial equipment
Part
Number
OPI150
Medical equipment
OPI153
Office equipment
OPI155
LED
Peak
Wavelength
890 nm
890 nm or 935
nm
890 nm
VCE
Isolation
Lead
Voltage
CTR
IF (mA)
(Volts) Length /
Sensor
(,000) Min / Max Typ / Max
Max
Spacing
Transistor
10 / NA
16 / 50
30
0.40" /
50
Darlington
25 / NA
30 / 50
15
3.16"
TIA –OC
80 / NA
10 / 50
18
OPI150
1
3
4 - Base
2
5
OPI153
OPI155
1
5
2
RoHS
DIMENSIONS ARE IN:
4
3
Pin #
LED
1
2
Anode
Cathode
[MILLIMETERS]
INCHES
Pin # OPI150 & OPI153 Pin #
3
4
5
Collector
Base
Emitter
3
4
5
OPI155
Ground
Vcc
Output
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue C 10/2010
Page 1 of 3
Optically Coupled Isolator /
High-Speed Optically Coupled Isolator
OPI150, OPI153, OPI155
Absolute Maximum Ratings (TA = 25° C unless otherwise noted)
Operating Temperature Range
-40° C to +85° C
Storage Temperature Range
-40° C to +85° C
(1)(2)
±50 kVDC
Input-to-Output Isolation Voltage
](3)
Lead Soldering Temperature [1/16 inch (1.6 mm) from the case for 5 seconds with soldering iron
260° C
Input Diode
Continuous Forward Current
50 mA
Reverse Voltage
Power Dissipation
3V
(4)
200 mW
Output Phototransistor or Photodarlington (OPI150, OPI153)
Collector-Base Voltage
OPI150
OPI153
30 V
20 V
Collector-Emitter Voltage
OPI150
OPI153
30 V
15 V
Emitter-Collector Voltage
5.0 V
Power Dissipation(5)
250 mW
Output Photosensor (OPI155)
Supply Voltage
-0.5 to 7 V
Output Voltage
-0.5 to 18 V
Output Current
25 mA
Open-Collector Power Dissipation
Power Dissipation
Notes:
(1)
(2)
(3)
(4)
(5)
40 mW
(5)
250 mW
For OPI150 and OPI153, measured with input leads and output leads shorted.
For OPI155, measured with input and output leads shorted and relative humidity of less than 50%.
RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
Derate linearly 3.33 mW/° C above 25° C.
Derate linearly 4.17 mW/° C above 25° C.
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Input Diode (For OPI150 & OPI153, see OP236 for additional information - for reference only. For OPI155, see OP235W for
additional information - for reference only.)
VF
Forward Voltage
OPI150, OPI153
OPI155
-
1.3
1.2
1.6
1.6
V
IF = 50 mA
IF = 10 mA
IR
Reverse Current
-
0.1
100
µA
VR = 3 V
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue C 10/2010
Page 2 of 3
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Optically Coupled Isolator /
High-Speed Optically Coupled Isolator
OPI150, OPI153, OPI155
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN
TYP
MAX
UNITS
TEST CONDITIONS
Output Phototransistor or Photodarlington (For OPI150, see OP805SL for additional information, for OPI153, see OP830SL
for additional information- for reference only.)
V(BR)CEO
Collector-Emitter Breakdown Voltage
OPI150
OPI153
30
15
-
-
V
IC = 1 mA
V(BR)ECO
Emitter-Collector Breakdown Voltage
OPI150, OPI153
5
-
-
V
IF = 100 µA
V(BR)CBO
Collector-Base Breakdown Voltage
OPI150
OPI153
30
20
-
-
V
IC = 100 µA
nA
VCE = 10 V
nA
VCB = 10 V
%
IF = 10 mA, VCE = 5 V
IF = 20 mA, VCE = 5 V
µA
IF = 20 mA, VCB = 5 V
V
IF = 16 mA, IC = 1 mA
IF = 30 mA, IC = 2 mA
µA
VO = 18 V, IF = 0, VCC = Open
mA
VCC = 5.25 V, IF = 0, VO = Open
mA
VCC = 5.25 V, IF = 10 mA, VO = 0
ICEO
Collector-Emitter Dark Current
OPI150
OPI153
-
-
100
500
ICBO
Collector-Base Dark Current
OPI150
-
-
-
DC Current Transfer Ratio
OPI150
OPI153
10
25
-
-
ICB(ON)
Ib0State Photodiode Current
OPI150
10
-
-
vCE(SAT)
Saturation Voltage
OPI150
OPI153
-
-
0.5
1.2
Coupled (OPI150, OPI153)
IC/ IF
Output Photosensor (OPI155)
IOH
High Level Output Current
OPI155
-
-
250
ICCH
High Level Supply Current
OPI155
-
-
6.5
ICCL
Low Level Supply Current
OPI155
-
-
10
vOL
Low Level Output Voltage
OPI155
-
-
0.5
V
VCC = 5.25 V, IF = 10 mA, IO = 8 mA
ns
VCC = 5 V, IF = 10 mA, RL = 360 Ω
Switching Characteristics (OPI155)
TPHL
Propagation Delay, High to Low
-
120
150
TPLH
Propagation Delay, Low to High
-
70
100
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747
FAX: (972) 323-2396 [email protected] www.optekinc.com
Issue C 10/2010
Page 3 of 3