High Speed Characterization Report DCC-08-XX-G-PF-1-4-1 Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Table of Contents Eye Pattern Summary ..................................................................................................... 3 Frequency Domain Data Summary ................................................................................. 5 Bandwidth Chart – Differential Insertion Loss .............................................................. 6 Time Domain Data Summary ...................................................................................... 7 Characterization Details .................................................................................................. 9 Differential and Single-Ended Data.............................................................................. 9 Cable assembly Signal to Ground Ratio ...................................................................... 9 Eye Diagram Data ..................................................................................................... 11 Frequency Domain Data ............................................................................................ 11 Time Domain Data ..................................................................................................... 11 Appendix A – Eye Diagrams ......................................................................................... 13 Appendix B – Frequency Domain Response Graphs .................................................... 17 Differential Application – Insertion Loss ..................................................................... 17 Differential Application – Return Loss ........................................................................ 18 Differential Application – NEXT Configurations ......................................................... 19 Differential Application – FEXT Configurations .......................................................... 20 Differential Application – Differential to Common Mode Conversion.......................... 21 Appendix C – Time Domain Response Graphs ............................................................. 22 Differential Application – Input Pulse ......................................................................... 22 Differential Application – Cable Assembly Impedance............................................... 22 Differential Application – Cable assembly Impedance ............................................... 24 Differential Application – Propagation Delay .............................................................. 26 Appendix D – Product and Test System Descriptions ................................................... 27 Test System Description ............................................................................................ 27 PCB-103418-TST-XX Test Fixtures........................................................................... 28 PCB Fixtures ............................................................................................................. 29 Appendix E – Test and Measurement Setup ................................................................. 31 N5230C Measurement Setup .................................................................................... 31 Test Instruments ........................................................................................................ 31 Test Cables & Adapters ............................................................................................. 31 DSA8200 Measurement Setup .................................................................................. 32 Test Instruments ........................................................................................................ 32 Test Cables & Adapters ............................................................................................. 32 Appendix F - Frequency and Time Domain Measurements .......................................... 33 Eye Diagram Procedures ........................................................................................... 33 Eye Mask ............................................................................................................... 34 Rise Time ............................................................................................................... 34 Frequency (S-Parameter) Domain Procedures ......................................................... 35 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:ii Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Time Domain Procedures .......................................................................................... 37 Impedance (TDR)................................................................................................... 37 Propagation Delay (TDT) ....................................................................................... 37 Appendix G – Glossary of Terms .................................................................................. 38 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:iii Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Cable Assembly Overview The 2.00 mm( .0787")DCC Cable Assembly is constructed using 32 AWG twinax cable. Each end is a one row structures with up to 12 signal pairs. The DCC-08-G-PF-1-4-1 assembly is wired to facilitate a Pin 1 to Pin N mapping between the cable ends. The data in this report is applicable to 09.0 and 40.0 inches cable assembly. Each DCC assembly was tested by press fit to a PCB at each end. One sample of each assembly was tested. The actual part numbers that were tested are shown in Table 1, which also identifies End 1 and End 2 of each assembly. A relative sample picture is shown in Figure1. Two differential pairs were tested. Length 09.0 inches 40.0 inches Part Number End 1 DCC-08-09.0-G-PF-1-4-1 DCC DCC-08-40.0-G-PF-1-4-1 DCC Table 1: Sample Description End 2 DCC DCC Figure 1: Test Sample Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:1 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Cable Assembly Speed Rating The cable assembly Speed Rating is based on the –7 dB insertion loss point of the mated cable assembly. The –7 dB point can be used to estimate usable system bandwidth in a typical two-level signaling environment. To calculate the Speed Rating, the measured –7 dB point is rounded up to the nearest half-GHz level. The up-rounding corrects for any loss from the test board traces. The resulting loss value is then doubled to determine the approximate maximum data rate in Gigabits per second (Gbps). The following table summarizes the Cable Assembly Speed Ratings for the DCC cable assemblies tested. Assembly -7 dB Frequency Side Pair 15.0 GHz DCC-08-09.0-G-PF-1-4-1 Center Pair 12.0 GHz Side Pair 9.0 GHz DCC-08-40.0-G-PF-1-4-1 Center Pair 7.5 GHz Table 2: Cable Assembly Speed Rating Speed Rating 30 Gbps 24 Gbps 18 Gbps 15 Gbps The Samtec Speed Rating is best considered a figure of merit for comparing relative performance between cable assemblies. The Speed Rating becomes less meaningful in systems using multi-level signaling or where crosstalk or impedance mismatch are more critical parameters. Modern high-speed digital transceivers can accommodate roughly 9 dB of loss and still operate reliably. The –7 dB rating is a conservative number that allocates 2 dB of system budget for other channel components such as short PCB traces and IC packaging effects. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:2 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Eye Pattern Summary DCC-08-09.0-G-PF-1-4-1 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:3 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB DCC-08-40.0-G-PF-1-4-1 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:4 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Frequency Domain Data Summary Table 3 – Cable Assembly System Performance Test Parameter Insertion Loss Return Loss Near-End Crosstalk Far-End Crosstalk Configuration Side Pair Center Pair Side Pair Center Pair In Row: Side Pairs In Row: Center Pairs In Row: Side Pairs In Row: Center Pairs Driver Receiver 0.23m 1m End 1_DCC_1,2 End 1_DCC_7,8 End 1_DCC_1,2 End 1_DCC_7,8 End 2_DCC_16,15 End 2_DCC_10,9 End 1_DCC_1,2 End 1_DCC_7,8 7dB@ 14.8 GHz 7dB@ 11.9 GHz >10dB to 14.9 GHz >10dB to 10.9 GHz 7dB@ 9.0 GHz 7dB@ 7.2 GHz >10dB to 18.3 GHz >10dB to 18.6 GHz End 1_DCC_1,2 End 1_DCC_3,4 <-20dB to 3.8 GHz <-20dB to 4.6 GHz End 1_DCC_7,8 End 1_DCC_9,10 <-20dB to 3.8 GHz <-20dB to 4.1 GHz End 1_DCC_1,2 End 2_DCC_14,13 <-20dB to 3.1 GHz <-20dB to 4.4 GHz End 1_DCC_7,8 End 2_DCC_8,7 <-20dB to 2.7 GHz <-20dB to 3.7 GHz Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:5 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Bandwidth Chart – Differential Insertion Loss Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:6 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Time Domain Data Summary 0.23m : Differential Application _ Impedance 1m : Differential Application _ Impedance Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:7 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Table 4 - Propagation Delay (Cable Assembly) Driver/ Receiver Driver/ Receiver End 1_DCC_1,2/ End 2_DCC_16,15 End 1_DCC_7,8/ End 2_DCC_10,9 0.23m 1.16ns 1.17ns 1m 4.89ns 4.90ns Cable length Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:8 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Characterization Details This report presents data that characterizes the signal integrity response of a cable assembly in a controlled printed circuit board (PCB) environment. All efforts are made to reveal typical best-case responses inherent to the system under test (SUT). In this report, the SUT includes the mating connectors, cable assembly, and footprint effects on a typical multi-layer PCB. PCB effects (trace loss) are de-embedded from test data. Board related effects, such as pad-to-ground capacitance, are included in the data presented in this report. Additionally, intermediate test signal connections can mask the cable assembly’s true performance. Such connection effects are minimized by using high performance test cables and adapters. Where appropriate, calibration and de-embedding routines are also used to reduce residual effects. Differential and Single-Ended Data Most Samtec cable assemblies can be used successfully in both differential and singleended applications. However, electrical performance will differ depending on the signal drive type. In this report, data is presented for “GSSG” differential drive configuration only. Cable assembly Signal to Ground Ratio Samtec cable assemblies are most often designed for generic applications and can be implemented using various signal and ground pin assignments. In high speed systems, provisions must be made in the interconnect for signal return currents. Such paths are often referred to as “ground”. In some cable assemblies, a ground plane or blade, or an outer shield, is used as the signal return, while in others, cable assembly pins are used as signal returns. Various combinations of signal pins, ground blades, and shields can also be utilized. Electrical performance can vary significantly depending upon the number and location of ground pins. In general, the more pins dedicated to ground, the better electrical performance will be. But dedicating pins to ground reduces signal density of a cable assembly. Therefore, care must be taken when choosing signal/ground ratios in cost or density-sensitive applications. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:9 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB For this cable assembly, the following array configurations are evaluated: Differential Impedance: Side Pair (Signal pair on the side of connector) Center Pair (Signal pair on the center of connector) Differential Crosstalk: In Row: Side Pairs (adjacent pairs on the side of connector) In Row: Center Pairs (adjacent pairs on the center of connector) See Appendix D – Product and Test System Descriptions for details Two differential pairs were driven for crosstalk measurements. Other configurations can be evaluated upon request. Please contact [email protected] for more information. In a real system environment, active signals might be located at the outer edges of the signal contacts of concern, as opposed to the ground signals utilized in laboratory testing. For example, in a single-ended system, a pin-out of “SSSS”, or four adjacent single ended signals might be encountered as opposed to the “GSG” and “GSSG” configurations tested in the laboratory. Electrical characteristics in such applications could vary slightly from laboratory results. But in most applications, performance can safely be considered equivalent. Signal Edge Speed (Rise Time) In pulse signaling applications, the perceived performance of the interconnect can vary significantly depending on the edge rate or rise time of the exciting signal. For this report, the fastest rise time used was 30 ps. Generally, this should demonstrate worstcase performance. In many systems, the signal edge rate will be significantly slower at the cable assembly than at the driver launch point. To estimate interconnect performance at other edge rates, data is provided for several rise times between 30ps and 500ps. Unless otherwise stated, measured rise times were at 10%-90% signal levels. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:10 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Eye Diagram Data Eye patterns are a time domain characterization of system level performance. Eye patterns are generated by sending continuous streams of data from a transmitter to a receiver, and overlaying the received signals upon one another. Over time, the received data builds to resemble an eye. Negative SI effects in the transmission path can cause the signal to distort, which over time, will cause the eye to “close”. Specifications, such as an eyemask template, can be placed on the amount of open area required in the eye to ensure a functional system. An eyemask template is a representation of the receiver’s sensitivity and is often used as a metric of performance. While there are lot-to-lot and vendor-to-vendor variations in receiver sensitivity, some general guidelines can be developed. After reviewing several major industry standards (PCIe, Gigabit Ethernet) we find similar eyemask requirements and we will use these as the basis for a generic template in this report. For this report we will assume a receiver amplitude sensitivity of 50 mVpp and a jitter margin of 0.5 UI. This results in a diamond shape eyemask template that is 50 mV high and 0.5 UI wide. Please contact our Signal Integrity Group at [email protected] for more information. Frequency Domain Data Frequency Domain parameters are helpful in evaluating the cable assembly system’s signal loss and crosstalk characteristics across a range of sinusoidal frequencies. In this report, parameters presented in the Frequency Domain are Insertion Loss, Return Loss, Near-End and Far-End Crosstalk, and Mode Conversion. Other parameters or formats, such as VSWR or S-Parameters, may be available upon request. Please contact our Signal Integrity Group at [email protected] for more information. Frequency performance characteristics for the SUT are generated directly from network analyzer measurements. Time Domain Data Time Domain parameters indicate Impedance mismatch versus length, and signal propagation time in a pulsed signal environment. The measured S-Parameters from the network analyzer are post-processed using Agilent ADS to obtain the time domain response. Time Domain procedure is provided in Appendix F of this report. Parameters or formats not included in this report may be available upon request. Please contact our Signal Integrity Group at [email protected] for more information. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:11 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB In this report, propagation delay is defined as the signal propagation time through the cable assembly, mating connectors, and connector footprint. It also includes 17.5 mils of PCB trace on each connector side. Delay is measured at 30 picoseconds signal risetime. Delay is calculated as the difference in time measured between the 50% amplitude levels of the input and output pulses. Data for other configurations may be available. Please contact our Signal Integrity Group at [email protected] for further information. Additional information concerning test conditions and procedures is located in the appendices of this report. Further information may be obtained by contacting our Signal Integrity Group at [email protected]. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:12 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix A – Eye Diagrams DCC-08-09.0-G-PF-1-4-1 30Gbps: Side Pair Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:13 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB 24Gbps: Center Pair Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:14 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB DCC-08-40.0-G-PF-1-4-1 18Gbps: Side Pair Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:15 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB 15Gbps: Center Pair Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:16 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix B – Frequency Domain Response Graphs Differential Application – Insertion Loss Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:17 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – Return Loss Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:18 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – NEXT Configurations Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:19 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – FEXT Configurations Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:20 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – Differential to Common Mode Conversion Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:21 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix C – Time Domain Response Graphs Differential Application – Input Pulse Differential Application – Cable Assembly Impedance 0.23m: Differential Application _ Impedance Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:22 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB 1m: Differential Application _ Impedance Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:23 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – Cable assembly Impedance DCC-08-09.0-G-PF-1-4-1 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:24 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB DCC-08-40.0-G-PF-1-4-1 Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:25 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Differential Application – Propagation Delay Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:26 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix D – Product and Test System Descriptions Product test samples are 2.00 mm pitch DCC cable asseblies.The part number are DCC-08-09.0-G-PF-1-4-1 and DCC-08-40.0-G-PF-1-4-1. The cable assembly has one row of 8 signal pairs evenly spaced on a 2.00 mm (0.0787”) pitch. A photo of the mated test article mounted to SI test boards is shown below. Each end is one row structures with up to 12 signal pairs. The DCC-08-G-PF-1-1-4 assembly is wired to facilitate a Pin 1 to Pin N mapping between the cable ends. The data in this report is applicable to 09.0 and 40.0 inches cable assembly. The cable assembly terminations had a particular signal line configuration. The signal line numbers are shown in table below. There are a total of 16 positions. SMA jack numbers on the test boards correspond to the assembly line numbers. All adjacent lines are terminated where applicable. End 1 End 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR PAIR 10 8 6 4 2 16 15 14 13 12 11 9 7 5 3 NUMBER OF GND PINS: 20 1 Table 5: Signal line numbers Test System Description The test fixtures are composed of Four-layer FR-406 material with 50Ω signal trace and pad configurations designed for the electrical characterization of Samtec high speed cable assembly products. A PCB mount SMA connector is used to interface the VNA test cables to the test fixtures. Optimization of the SMA launch was performed using full wave simulation tools to minimize reflections. Two test fixture specific to the DCC series cable assembly identified by part PCB-106558-SIG-02AX and PCB-106558-SIG-02BX. The Auto Fixture Removal (AFR) calibration structures designed specifically for the DCC series are on the fixture PCB-106558-SIG-03. Displayed on the following pages is information for the DCC/AFR calibration structure and directives for mating DCC fixtures. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:27 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB PCB-103418-TST-XX Test Fixtures Artwork of the PCB design is shown below. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:28 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB PCB Fixtures The test fixtures used are as follows: Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:29 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB PCB-106558-SIG-02AX – DCC Cable Test Board First End PCB-106558-SIG-02BX – DCC Cable Test Board Second End PCB-106558-SIG-03 – Open and Through Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:30 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix E – Test and Measurement Setup The test instrument is the Agilent N5230C PNA-L network analyzer. Frequency domain data and graphs are obtained directly from the instrument. Post-processed time domain data and graphs are generated using convolution algorithms within Agilent ADS. The network analyzer is configured as follows: Start Frequency – 300 KHz Stop Frequency – 20 GHz Number of points -1601 IFBW – 1 KHz With these settings, the measurement time is approximately 20 seconds. N5230C Measurement Setup Test Instruments QTY Description 1 Agilent N5230C PNA-L Network Analyzer (300 KHz to 20 GHz) 1 Agilent N4433A ecal module (300 KHz to 20 GHz) Test Cables & Adapters QTY Description 4 Gore OWD01D02039-4 (DC-26.5 GHz) Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:31 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB For impedance measurements, the test instrument is the Tektronix DSA8200 Digital Serial Analyzer mainframe and 80E04 sampling module. The impedance data and profiles are obtained directly from the instrument. The Digital Analyzer is configured as follows: Vertical Scale: Offset: Horizontal Scale: Record Length: Averages: 2 ohm / Div: Default / Scroll 500ps/ Div or 1.5ns/Div 4000 ≥ 16 DSA8200 Measurement Setup Test Instruments QTY Description 1 Tektronix DSA8200 Digital Serial Analyzer 2 Tektronix 80E04 Dual Channel 20 GHz TDR Sampling Module Test Cables & Adapters QTY Description 2 Samtec RF405-01SP1-01SP1-0305 (DC-20 GHz) Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:32 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix F - Frequency and Time Domain Measurements Eye Diagram Procedures Eye Diagrams and statistical eye diagram metrics such as eye height can be generated by post-processing Frequency Domain measurements using Agilent ADS. Simulated data is sent over a touchstone model and the bits are overlain into an eye pattern. Currently, no CEI specification is available for 7Gbps, so CEI-28-VSR Working Clause Proposal, CEI Implementation agreement Draft 7.0, dated May 14, 2012 was used for this report. The simulation circuit is modeled as: Agilent’s Advanced Design System Tx and Rx modules that are configured to the CEI28-VSR Working Clause Proposal, CEI Implementation agreement Draft 7.0, dated May 14, 2012. Tx parameters are specified in Section 1.3.3, Module-to-Host Specifications, Table 1-4, Page 7. Rx parameters defined in Section 1.3.2 Host-to-Module Electrical Specifications, Table 1-1, Page 5. SUT Cable Assembly S-Parameter measurements o 17.5 mils of 10.2 mil wide differential stripline signal trace o Test board vias, pads (footprint effects) for the DCC connector o The DCC cable assembly o Test board vias, pads (footprint effects) for the DCC connector o 17.5 mils of 10.2 mil wide differential stripline signal trace All traces were modeled as microstrip on FR4 with the following parameters: The FR4 parameters are modeled using: o Er = 3.7 @ 1 GHz o Loss Tangent = 0.02 @ 1 GHz Copper is modeled as: o Conductivity = 4.5E+7 S-m o Surface roughness = 0.6 micron Traces are microstrip with the following geometry: o 10.2 mil trace width o 2 mil trace copper thickness o 5.8 mil FR4 dielectric thickness Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:33 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Eye Mask The eye mask is set for 50mVpp, with a jitter margin of 0.5 UI. Rise Time The 10-90 risetime of the 30 Gbps signal was determined to be 23 psec, using the following formula: Risetime = 0.35/Bandwidth Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:34 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Frequency (S-Parameter) Domain Procedures The quality of any data taken with a network analyzer is directly related to the quality of the calibration standards and the use of proper test procedures. For this reason, extreme care is taken in the design of the AFR calibration standards, the SI test boards, and the selection of the PCB vendor. The measurement process begins with a measurement of the AFR calibration standards. A coaxial SOLT calibration is performed using an N4433A E-cal module. This measurement is required in order to obtain precise values of the line standard offset delay and frequency bandwidths. Measurements of the 2x through line standard can be used to determine the maximum frequency for which the calibration standards are valid. For the DCC test boards, this is greater than 20 GHz. The figure below shows how the THRU reference traces are utilized to compensate for the losses due to the coaxial test cables and the test fixture during testing. The calibration board is characterized to obtain parameters required to define the 2x Thru. 2x Thru calibration trace Reference plane Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:35 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Measurements are then performed using the test boards as shown below. The test board effects are removed in post-processing via AFR in Agilent PLTS. The calibrated reference plane is located 17.5 mils from the connector footprint on each side. The SParameter measurements include: A. B. C. D. E. 17.5 mils of 10.2 mil wide differential stripline signal trace Test board vias, pads (footprint effects) for the DCC connector The DCC test cable Test board vias, pads (footprint effects) for the DCC connector 17.5 mils of 10.2 mil wide differential stripline signal trace The figure below shows the location of the measurement reference plane. Test fixture 1 Test fixture 2 Reference plane Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 Reference plane WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:36 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Time Domain Procedures Mathematically, Frequency Domain data can be transformed to obtain a Time Domain response. Perfect transformation requires Frequency Domain data from DC to infinity Hz. Fortunately, a very accurate Time Domain response can be obtained with bandwidth-limited data, such as measured with modern network analyzer. The Time Domain responses were generated using Agilent ADS 2011 update 10. This tool has a transient convolution simulator, which can generate a Time Domain response directly from measured S-Parameters. An example of a similar methodology is provided in the Samtec Technical Note on domain transformation. http://www.samtec.com/Documents/WebFiles/Technical_Library/Reference/Articles/tech -note_using-PLTS-for-time-domain-data_web.pdf Impedance (TDR) A step pulse is applied to the touchstone model of the cable assembly and the reflected voltage is monitored. The reflected voltage is converted to a reflection coefficient and then transformed into an impedance profile. All ports of the Touchstone model are terminated in 50 ohms. Propagation Delay (TDT) The Propagation Delay is a measure of the Time Domain delay through the cable assembly and footprint. A step pulse is applied to the touchstone model of the cable assembly and the transmitted voltage is monitored. The same pulse is also applied to a reference channel with zero loss, and the Time Domain pulses are plotted on the same graph. The difference in time, measured at the 50% point of the step voltage is the propagation delay. Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:37 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved High Speed Characterization Report Series: 2.00 mm (.0787") pitch DCC Description: High Speed Press Fit, 100Ω differential pair signal routing, 32 AWG Twinax Cable Assembly, Low cost one-time press-fit termination to PCB Appendix G – Glossary of Terms ADS – Agilent Advanced Design System AFR – Automatic Fixture Removal CTLE – Continuous Time Linear Analyzer DUT – Device under test FD – Frequency domain FEXT – Far-End Crosstalk HDV – High Density Vertical NEXT – Near-End Crosstalk OV – Optimal Vertical OH – Optimal Horizontal PCB – Printed Circuit Board PLTS – Agilent Physical Layer Design System PPO – Pin Population Option SE – Single-Ended SI – Signal Integrity SUT – System Under Test S – Static (independent of PCB ground) SOLT – acronym used to define Short, Open, Load & Thru Calibration Standards TD – Time Domain TDA – Time Domain Analysis TDR – Time Domain Reflectometry TDT – Time Domain Transmission UI – Unit Interval XROW – Across Row Z – Impedance (expressed in ohms) Samtec Inc. 520 Park East Blvd. New Albany IN 47151-1147 USA ©Samtec, Inc. 2005 WWW.SAMTEC.COM 1-800-SAMTEC-9 (US & Canada) [email protected] Page:38 Phone: 812-944-6733 Fax: 812-948-5047 Report Revision: 11/25/2014 All Rights Reserved