F-215 ECDP–08–03.75–B1–B2–3–1 ECDP–32–03.75–L1–L2–1–1 (0,80 mm) .0315" ECDP SERIES TWINAX EDGE CARD CABLE ASSEMBLY SPECIFICATIONSi For complete specifications or www.samtec.com?ECDP Cable: 30 AWG twinax AcceleRate™ cable Plating: Edge Card = ENIG, 3-10 microinches Operating Temp Range: -55°C to +85°C Current Rating: 2.3 A per pin (2 adjacent pins powered) Impedance: -1 = 100Ω Differential -2 = 85Ω Differential Bend Radius: 1 mm one time bend, or (12,7 mm) .50" bend radius with moderate flexing cycles Pinout Map: See web address above RoHS Compliant: Yes Low Profile vs. Mini-SAS Mates with: HSEC8 (–L2 option), HSEC8 (–BL option) APPLICATION 30 AWG, 100Ω AcceleRate™ twinax cable TM Metal squeeze latch Mates with vertical or right angle connectors on board RECOGNITIONS For complete scope of recognitions see www.samtec.com/quality NO. OF PAIRS TYPE ECDP ECDP Cable Length Rated @ 7dB Insertion Loss 12" (0,305 m) 23 Gbps 36" (0,914 m) 18.5 Gbps Longer cables and better performance available. See ECDP-E Series Performance and complete test data available at www.samtec.com?ECDP or contact [email protected] = Edge Card Cable NO. OF PAIRS –04 –08 –16 –32 –04, –08, –16, –32 WIRE LENGTH END 1 –“XX.XX” = Wire Length in Inches (95,3 mm) 03.75" minimum A –L1 –L1 = Double Vertical with latches = Double Vertical with latches (Wiring option –3 & –4 only) –B1 = Board lock, No housing (20,85) .821 END 2 (24,05) .947 (33,66) 1.325 (52,86) 2.081 OAL = Wire Length + (16,89) .665 N-1 N WIRING OPTION –L2 = Double Vertical with latches (Wiring option –1 & –2 only) IMPEDANCE –1 –1 = Pin 1 to Pin 1 = 100Ω –2 = 85Ω –2 = Pin 1 to Pin 2 –3 = Pin 1 to Pin N-1 –4 CABLE CONNECTOR ECDP–04 ECDP–08 ECDP–16 ECDP–32 = Pin 1 to Pin N –B1 Notes: Cable shield construction leaves minor exposed edges. Users should consider whether this will affect the application in which the cable is to be used. Insulation may be required as needed. 02 = Board lock, No housing (Wiring option –3 & –4 only) A 02 Cable lengths longer than 40.00" (1 meter) are not supported with S.I. test data. Design your High Speed Cable with Samtec’s High Speed Cable Solutionator® at www.samtec.com/hdr HSEC8–109–XX HSEC8–113–XX HSEC8–125–XX HSEC8–149–XX 01 (21,00) .827 –B2 (END 2) –L1 (END 1) (1,53) .060 (6,27) .247 –B2 = Board lock, No housing (Wiring option –1 & –2 only) Some lengths, styles and options are non-standard, non-returnable. WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice. N –L1 (END 2)* *Same pinout for –B1 end 2 and –L1 end 2. F-215 ECDP–E–08–03.75–L1–L1–1–1 ECDP–E–16–03.75–L1–L1–1–1 (0,80 mm) .0315" ECDP-E SERIES EQUALIZED TWINAX EDGE CARD CABLE SPECIFICATIONSi Mates with: HSEC8 (–L2 option) Passive Equalization for improved performance For complete specifications www.samtec.com?ECDP-E Cable: 30 AWG twinax AcceleRate™ cable Plating: Edge Card = ENIG, 3-10 microinches Operating Temp Range: -55°C to +85°C Impedance: -1 = 100Ω Differential Bend Radius: 1 mm one time bend, or (12,7 mm) .50" bend radius with moderate flexing cycles Pinout Map: See web address above RoHS Compliant: Yes RECOGNITIONS Performance Comparisons ECDP-E Δ 62" (1.6 m) 86" (2.2 m) +39% N/A 25" (0.64 m) N/A Data Rate ECDP 14 Gbps 28 Gbps Cable Length ECDP ECDP-E Δ 12" (305 mm) 23 Gbps 30 Gbps +30% 36" (914 mm) 18.5 Gbps 24.5 Gbps +32% TM Rated at 7dB insertion loss Performance and complete test data available at www.samtec.com?ECDP-E or contact [email protected] For complete scope of recognitions see www.samtec.com/quality NO. OF PAIRS TYPE ECDP-E = Equalized Edge Card Cable –04, –08, –16, –32 WIRE LENGTH –“XX.XX” = Wire Length in Inches (95,3 mm) 03.75" minimum END 1 –L1 –L1 = Double Vertical with latches = Double Vertical with latches (Wiring option –3 & –4 only) OAL = Wire Length + (16,89) .665 N A Notes: Cable shield construction leaves minor exposed edges. Users should consider whether this will affect the application in which the cable is to be used. Insulation may be required as needed. Cable lengths longer than 40.00" (1 meter) are not supported with S.I. test data. Design your High Speed Cable with Samtec’s High Speed Cable Solutionator® at www.samtec.com/hdr END 2 (21,00) .827 –L2 (END 2) –L1 (END 1) –1 = 100Ω –3 = Pin 1 to Pin N-1 –4 = Pin 1 to Pin N NO. OF PAIRS –04 –08 –16 –32 (6,27) .247 (1,53) .060 –1 –2 –L2 Some lengths, styles and options are non-standard, non-returnable. WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice. IMPEDANCE = Pin 1 to Pin 1 = Pin 1 to Pin 2 = Double Vertical N-1 with latches (Wiring option –1 & –2 only) 01 02 WIRING OPTION A (20,85) .821 (24,05) .947 (33,66) 1.325 (52,86) 2.081