HIGH SPEED EDGE CARD CABLE ASSEMBLY

F-212 SUPPLEMENT
(0,80mm) .0315"
EEDP–016–06.00–RA1–RA1–4
EEDP SERIES
EEDP–016–08.00–DS1–RA2–1
HIGH SPEED EDGE CARD CABLE ASSEMBLY
SPECIFICATIONS
100Ω
Differential
Pair Routing
Mates with:
MEC8-02-RA, HSEC8
For complete specifications
see www.samtec.com?EEDP
Cable:
30 AWG
twinax micro ribbon
Signal Routing:
100Ω Differential
Cable Bending Radius:
(11,11mm) 7/16" min
Current Rating:
1 A max
Propagation Delay:
4.67 nsec/meter
Operating Temp Range:
-20°C to +90°C
Skew (pair-to-pair):
<10 ps/ft
Skew (within a pair):
<5 ps/ft
EMI Performance:
FCC Class A
Pinout Map:
See web address above
RoHS Compliant:
Yes
30 AWG
twinax ribbon
cable
APPLICATIONS
Latching
system
option
for rugged
applications.
Mates with
Vertical and
Right Angle
connectors
on board
Cable
Length
19.68" (0,5m)
39.37" (1m)
Captive Panel Screw and
Latching Options
APPLICATION
SPECIFIC
EEDP
• Customized routings
• Board hardware for
mounting with right angle
captive screws (RAH-01)
• Other terminations
• Other lengths
Contact Samtec.
NO. OF
PAIRS
= Wire Length
in Inches
(43,7mm) 01.72"
minimum
APPLICATIONS
MEC8–RA
to
EEDP–RAX
N
N-1
(17,99)
.708
(6,76)
.266
B
HSEC8
to
EEDP–DVX
A
C
Processing conditions will
affect mated height.
02
CABLE
CONNECTOR
EEDP–08
EEDP–16
EEDP–24
EEDP–32
HSEC8/MEC8–113
HSEC8/MEC8–125
HSEC8/MEC8–137
HSEC8/MEC8–149
Note:
Cable lengths longer than
40.00" (1 meter) are not
supported with S.I. test data.
Note:
This Series is non-standard,
non-returnable.
#4-40
Thread
–1
= Pin 1 to
Pin 1
–2
END
OPTION
Wire Length
± (1,27) .050
WIRING
OPTION
END
NO. 2
Specify
END OPTION
from chart
–“XX.XX”
–008, –016,
–024, –032
Performance and complete test data
available at www.samtec.com?EEDP
or contact [email protected]
END
NO. 1
WIRE
LENGTH
Rated @ 7dB
Insertion Loss
7.25 GHz / 14.50 Gbps
3.42 GHz / 6.84 Gbps
–DVX
–DSX
–RAX
–RSX
–LVX
–RLX
= Pin 1 to
Pin 2
ASSEMBLY
Vertical
–3
Vertical with Screws
= Pin 1 to
Pin N-1
(–024 N/A)
Right Angle
Right Angle with Screws
Vertical with Latches
–4
Right Angle with Latches
= Pin 1 to
Pin N
(–024 N/A)
Specify X=1 for standard orientation;
X=2 for flipped orientation
(XX1 to XX1 and XX2 to XX2
require -3 or -4 wiring)
(XX1 to XX2 and XX2 to XX1
require -1 or -2 wiring)
01
OAL = Wire Length
+ (17,65) .695
END NO. 1
(-DS1 STANDARD SHOWN)
(1,60)
.062
END NO. 2
(-RA2 FLIPPED SHOWN)
WWW.SAMTEC.COM
NO. OF
PAIRS
A
B
C
–008
(24,51)
.965
(34,67)
1.365
(26,00)
1.024
–016
(35,10)
1.382
(45,26)
1.782
(35,99)
1.417
–024
(44,70)
1.760
(54,86)
2.160
(45,01)
1.772
–032
(53,31)
2.099
(63,47)
2.499
(54,00)
2.126