Project Number: Design Verification Test Report Requested by: Wy Chiang Tracking Code: TC0928--2600_Report_Rev_2 Date: 07/09/2009 Part #: HSEC8-160-01-L-RA Product Rev: 0 Lot #: N/A Part description: HSEC8 Test Start: 07/09/2009 Tech: Kason He Eng: Vico Zhao Qty to test: 60 Test Completed: 09/18/2009 Design Verification Test Report HSEC8-160-01-L-RA Page 1 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA CERTIFICATION All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST) traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable. All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be reproduced without prior written approval of Samtec. SCOPE To perform the following tests: design verification test, please see flowchart. APPLICABLE DOCUMENTS Standards: EIA Publication 364 TEST SAMPLES AND PREPARATION 1) 2) 3) 4) 5) All materials were manufactured in accordance with the applicable product specification. All test samples were identified and encoded to maintain traceability throughout the test sequences. After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001. Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used. The automated procedure is used with aqueous compatible soldering materials. 6) 7) 8) 9) Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary. Any additional preparation will be noted in the individual test sequences. Solder Information: Lead free Re-Flow Time/Temp: See accompanying profile. 10) Samtec Test PCBs used: PCB-101754-TST Page 2 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 TYPICAL OVEN PROFILE (Soldering Parts to Test Boards) Page 3 of 41 Part #: HSEC8-160-01-L-RA Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA FLOWCHARTS Gas Tight TEST STEP 01 02 03 GROUP A 200 Points (min) LLCR-1 Gas Tight LLCR-2 Gas Tight = EIA-364 -36A LLCR = EIA-364 -23, LLCR use Keithley 58 0 in the dry circuit mode, 10 mA Max Mating/Unmating/Gaps/Normal Force/Deflection Force TEST GROUP A GROUP B1 STEP 10 Boards Individual Co ntacts (30) min GROUP B2 Individual Co ntacts (30) min 01 02 03 04 05 06 07 08 09 10 11 12 13 14 Contact Gaps Setup Approve Setup Approve Mating / Unmating Normal Force Thermal Aging (Mated) Data Review Data Review Normal Force 1 00 Cycles Mating / Unmating Contact Gaps Data Review Thermal Aging (Mated ) Mating / Unmating Contact Gaps Data Review Humidity (Mated) Contact Gaps Mating / Unmating Thermal Aging = EIA-364-17, Test Condition 4, 105 deg C; Time Condition 'B' (250 ho urs) Humidity =EIA-364-31, Test Condition B (240 Ho urs) and Method I II (+25 ° C to +65 ° C @ 90%RH to 98% RH) ambient pre-co ndition and delete steps 7a and 7b Mating/Un-Mating Forces = EIA-364-13 Normal Fo rce = EIA-364-04 (Perpendicular) displacement Force = 12.7 mm/min +/- 6 mm/min Spec is 50 N @ 1 mm displacement Contact Gaps/Height - No standard method. Usually meas ured optically Page 4 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA IR / DWV TEST STEP 01 GROUP A1 GROUP A2 GROUP A3 GROUP B 2 Ma ted Sets 2 Unmated of Part # Being Tested 2 Unmated o f Mating Part # 2 Mated Sets Break Down Pin to Pin Break Down Pin to Pin Break Down Pin to Pin Pin to Pin DWV/Break Down Voltage DWV/Break Down Voltage DWV/Break Down Voltage IR & DWV at test voltage (on both mated sets and on each connector unmated) 02 Thermal Aging (both sets unmated) 03 IR & DWV at test voltage (on both mated sets and on each connector unmated) 04 Cyclic Humidity (both sets unmated) 05 IR & DWV at test voltage (on both mated sets and on each connector unmated) * - DWV on group B to be performed at Test Voltage DWV test voltage is equal to 75% of the lowest break down voltage from group A1, A2 or A3 Thermal Aging = EIA-364-17, Test Condition 4 (10 5 °C) Time Condition 'B' (2 50 hours ) Humidity = EIA-364-31, Test Condition B (240 Ho urs) and Method III (+25° C to +65° C @ 90%RH to 98% RH) ambient pre-condition and delete steps 7a and 7b IR = EIA-364-21 DWV = EIA-36 4-20, Test Condition 1 Page 5 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA Durability/Thermal Age/Cyclic Humidity TEST STEP 01 02 03 04 05 06 07 08 09 10 GROUP A 200 Points 10 0 Cycles LLCR-1 Data Review 100 Cycles LLCR-2 Data Review Th ermal Age LLCR-3 Data Review Cyclic Humidity LLCR-4 Thermal Aging = EIA-364-17, Test Condition 4, 105 deg C; Time Condition 'B' (2 50 hours) Humidity =EIA-364-31, Test Condition B (240 Ho urs) and Method III (+25 ° C to +65 ° C @ 90%RH to 98% RH) ambient pre-condition and delete steps 7a and 7b LLCR = EIA-364 -23, LLCR use Keithley 580 in the dry circuit mode, 1 0 mA Max Current Carrying Capacity DOUBLE ROW 3 Mated Assemblies Each Current Carrying Capacity TEST STEP 01 GROUP A GROUP B GROUP C GROUP D GROUP E 3 Mated Assemblies 3 Mated Assemblies 3 Mated Assemblies 3 Mated Assemblies 3 Mated Assemblies 2 CONTACT POWERED 4 CONTACTS POWERED 6 CONTACTS POWERED 8 CONTACTS POWERED ALL CONTACTS POWERED CCC CCC CCC CCC CCC (TIN PLATING) - Tabulate calculated current at RT, 65° C, 75° C and 95° C after derating 20% and based on 105° C (GOLD PLATING) - Tabulate calculated current at RT, 85° C, 95° C and 115° C after derating 20% and based on 125° C CCC, Temp rise = EIA-364-70 Page 6 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. THERMAL: 1) 2) 3) 4) 5) EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors. Test Condition 4 at 105° C. Test Time Condition B for 250 hours. All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. HUMIDITY: 1) 2) 3) 4) 5) Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors. Test Condition B, 240 Hours. Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b. All samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. MATING/UNMATING: 1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors. 2) The full insertion position was to within 0.003” to 0.004” of the plug bottoming out in the receptacle to prevent damage to the system under test. 3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling. NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING): 1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors. 2) The contacts shall be tested in the connector housing. 3) If necessary, a “window” shall be made in the connector body to allow a probe to engage and deflect the contact at the same attitude and distance (plus 0.05 mm [0.002”]) as would occur in actual use. 4) The connector housing shall be placed in a holding fixture that does not interfere with or otherwise influence the contact force or deflection. 5) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2, computer controlled test stand with a deflection measurement system accuracy of 5.0 µm (0.0002”). 6) The nominal deflection rate shall be 5 mm (0.2”)/minute. 7) Unless otherwise noted a minimum of five contacts shall be tested. 8) The force/deflection characteristic to load and unload each contact shall be repeated five times. 9) The system shall utilize the TC2 software in order to acquire and record the test data. 10) The permanent set of each contact shall be measured within the TC2 software. 11) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis and a print out will be stored with the Tracking Code paperwork. Page 7 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) EIA-364-70, Temperature Rise versus Current Test Procedure for Electrical Connectors and Sockets. 2 2) When current passes through a contact, the temperature of the contact increases as a result of I R (resistive) heating. 3) The number of contacts being investigated plays a significant part in power dissipation and therefore temperature rise. 4) The size of the temperature probe can affect the measured temperature. 5) Copper traces on PC boards will contribute to temperature rise: a. Self heating (resistive) b. Reduction in heat sink capacity affecting the heated contacts 6) A de-rating curve, usually 20%, is calculated. 7) Calculated de-rated currents at three temperature points are reported: a. Ambient о b. 80 C о c. 95 C о d. 115 C 8) Typically, neighboring contacts (in close proximity to maximize heat build up) are energized. 9) The thermocouple (or temperature measuring probe) will be positioned at a location to sense the maximum temperature in the vicinity of the heat generation area. 10) A computer program, TR 803.exe, ensures accurate stability for data acquisition. 11) Hook-up wire cross section is larger than the cross section of any connector leads/PC board traces, jumpers, etc. 12) Hook-up wire length is longer than the minimum specified in the referencing standard. INSULATION RESISTANCE (IR): To determine the resistance of insulation materials to leakage of current through or on the surface of these materials when a DC potential is applied. 1) PROCEDURE: a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Electrification Time 2.0 minutes iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances. 2) MEASUREMENTS: 3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000 megohms. Page 8 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA DIELECTRIC WITHSTANDING VOLTAGE (DWV): To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of environmental stresses so not to influence the readings from arcing that occurs during the measurement process. 1) PROCEDURE: a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Barometric Test Condition 1 iii. Rate of Application 500 V/Sec iv. Test Voltage (VAC) until breakdown occurs 2) MEASUREMENTS/CALCULATIONS a. The breakdown voltage shall be measured and recorded. b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage. c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage). LLCR: 1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. 2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition. 3) The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure Page 9 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA GAS TIGHT: 1) 2) 3) 4) To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh vapors which might lead to oxide formation that may degrade the electrical performance of the contact system. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure Procedure: a. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics for Electrical Connectors, Sockets and/or Contact Systems. b. Test Conditions: i. Class II--- Mated pairs of contacts assembled to their plastic housings. ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1. iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are added. v. Exposure time, 55 to 65 minutes. vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the surface of the acid than 3 inches. vii. The samples shall be dried after exposure for a minimum of 1 hour. о viii. Drying temperature 50 C ix. The final LLCR shall be conducted within 1 hour after drying. Page 10 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA RESULTS Temperature Rise, CCC at a 20% de-rating • CCC for a 30°C Temperature Rise -----------------------2.6A per contact • CCC for a 30°C Temperature Rise -----------------------2.1A per contact • CCC for a 30°C Temperature Rise -----------------------1.9A per contact • CCC for a 30°C Temperature Rise -----------------------1.7A per contact • CCC for a 30°C Temperature Rise -----------------------0.9A per contact Contact Gaps Male • Initial o Min-------------------------------------------------- 0.018” o Max ------------------------------------------------- 0.022” • After 100 Cycles o Min-------------------------------------------------- 0.028” o Max ------------------------------------------------- 0.035” • After Thermal o Min-------------------------------------------------- 0.031” o Max ------------------------------------------------- 0.039” • After Humidity o Min-------------------------------------------------- 0.032” o Max ------------------------------------------------- 0.038” Page 11 of 41 with 2 adjacent contacts powered with 4 adjacent contacts powered with 6 adjacent contacts powered with 8 adjacent contacts powered with all adjacent contacts powered Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Mating – Unmating Forces • Initial o Mating Min --------------------------------------- 8.93 Lbs Max--------------------------------------13.00 Lbs o Unmating Min --------------------------------------- 2.73 Lbs Max--------------------------------------- 3.70 Lbs • After 25 Cycles o Mating Min --------------------------------------- 8.42 Lbs Max--------------------------------------11.80 Lbs o Unmating Min --------------------------------------- 2.95 Lbs Max--------------------------------------- 3.90 Lbs • After 50 Cycles o Mating Min --------------------------------------- 8.05 Lbs Max--------------------------------------10.80 Lbs o Unmating Min --------------------------------------- 3.00 Lbs Max--------------------------------------- 3.80 Lbs • After 75 Cycles o Mating Min --------------------------------------- 7.89 Lbs Max--------------------------------------10.00 Lbs o Unmating Min --------------------------------------- 2.95 Lbs Max--------------------------------------- 4.20 Lbs • After 100 Cycles o Mating Min --------------------------------------- 7.58 Lbs Max--------------------------------------- 9.10 Lbs o Unmating Min --------------------------------------- 3.04 Lbs Max--------------------------------------- 3.90 Lbs • Thermal o Mating Min --------------------------------------- 5.97 Lbs Max--------------------------------------- 8.40 Lbs o Unmating Min --------------------------------------- 2.34 Lbs Max--------------------------------------- 4.30 Lbs • Humidity o Mating Min --------------------------------------- 5.56 Lbs Max--------------------------------------- 7.50 Lbs o Unmating Min --------------------------------------- 1.71 Lbs Max--------------------------------------- 3.00 Lbs Page 12 of 41 Part #: HSEC8-160-01-L-RA Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Normal Force at 0.020" deflection • Initial o Min-------------------------------------------------71.63 gf o Max ------------------------------------------------76.57 gf • Thermal o Min-------------------------------------------------69.18 gf o Max ------------------------------------------------74.96 gf Part #: HSEC8-160-01-L-RA Set ----- 0.0003" Set ----- 0.0005" Set ----- 0.0018" Set ----- 0.0025" Insulation Resistance minimums, IR • Initial o Mated------------------------------------------------10000Meg Ω ------------------------- Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass • Thermal o Mated------------------------------------------------10000Meg Ω ------------------------ Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass • Humidity o Mated------------------------------------------------10000Meg Ω ------------------------ Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass Dielectric Withstanding Voltage minimums, DWV • Initial o Breakdown Mated ----------------------------------------750VAC Unmated-------------------------------------700VAC o DWV Mated ----------------------------------------525VAC Unmated-------------------------------------525VAC o Working voltage Mated ----------------------------------------175VAC Unmated-------------------------------------175VAC • Thermal o DWV Mated ----------------------------------------525VAC Unmated-------------------------------------525VAC • Humidity o DWV Mated ----------------------------------------525VAC Unmated-------------------------------------525VAC Page 13 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA LLCR Durability (200 LLCR test points) • Initial --------------------------------------------------------------- 10.3 mOhms Max • Durability, 100 Cycles o <= +5.0 mOhms ----------------------------------- 200Points -------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure • Thermal o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure • Humidity o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure LLCR Gas Tight (200 LLCR test points) • Initial -----------------------------------------------------------------9.9 mOhms Max • Gas-Tight o <= +5.0 mOhms ----------------------------------- 200 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Page 14 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA DATA SUMMARY TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) High quality thermocouples whose temperature slopes track one another were used for temperature monitoring. 2) The thermocouples were placed at a location to sense the maximum temperature generated during testing. 3) Temperature readings recorded are those for which three successive readings, 15 minutes apart, differ less than 1° C (computer controlled data acquisition). 4) Adjacent contacts were powered: a. Linear configuration with 2 adjacent conductors/contacts powered Base Curve TC0928--2600 2(2x1) Contacts in Linear series Part Numbers: HSEC8-160-01-L-RA/PCB-101757-TST Derated 20 % RT Peak Amp RT Derated Amp Measured Current Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.6Amps 85 ° C 7.0 85 ° C Peak Amp Room Temp=23.5 C 85 ° C Derated Amp 95 ° C 6.0 6.0 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp Limit 5.0 115 ° C Peak Amp 4.8 125° C Limit 115 ° C Derated Amp 115 ° C Room Temp 4.0 3.7 3.2 3.0 3.0 2.6 2.0 1.8 1.5 Useful Range 1.0 0.0 20 40 60 80 Ambient Temperature, ° C Page 15 of 41 100 120 140 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 b. Part #: HSEC8-160-01-L-RA Linear configuration with 4 adjacent conductors/contacts powered Base Curve TC0928--2600 4(2x2) Contacts in Linear series Part Numbers: HSEC8-160-01-L-RA/PCB-101757-TST Derated 20 % RT Peak Amp RT Derated Amp Measured Current 85 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.1Amps 85 ° C Peak Amp 6.0 Room Temp= 24.2 C 85 ° C Derated Amp 95 ° C 95 ° C Peak Amp Maximum Current, Amp per Contact 5.0 95 ° C Derated Amp 4.9 Limit 115 ° C Peak Amp 115 ° C Derated Amp 4.0 3.9 115 ° C 125° C Limit Room Temp 3.1 3.0 2.6 2.4 2.1 2.0 1.5 1.2 Useful Range 1.0 0.0 20 40 60 80 100 120 140 Ambient Temperature, ° C c. Linear configuration with 6 adjacent conductors/contacts powered Base Curve TC0928--2600 6(2x3) Contacts in Linear series Part Numbers: HSEC8-160-01-L-RA/PCB-101757-TST Derated 20 % RT Peak Amp RT Derated Amp Measured Current Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.9 Amps 85 ° C 5.0 85 ° C Peak Amp Room Temp=24.0 C 4.5 85 ° C Derated Amp 95 ° C 4.4 95 ° C Peak Amp 95 ° C Derated Amp Maximum Current, Amp per Contact 4.0 Limit 3.5 115 ° C Peak Amp 3.5 115 ° C Derated Amp 125° C Limit 115 ° C 3.0 Room Temp 2.7 2.5 2.3 2.2 2.0 1.9 1.5 1.3 1.0 1.0 Useful Range 0.5 0.0 20 40 60 80 Ambient Temperature, ° C Page 16 of 41 100 120 140 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA d. Linear configuration with 8 adjacent conductors/contacts powered Base Curve TC0928--2600 8(2X4) Contacts in Linear series Part Numbers:HSEC8-160-01-L-RA/PCB-101757-TST Derated 20 % RT Peak Amp RT Derated Amp Measured Current Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.7Amps 85 ° C 4.5 85 ° C Peak Amp Room Temp= 24.9 C 85 ° C Derated Amp 95 ° C 4.0 3.9 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp 3.5 Limit 115 ° C Peak Amp 3.1 3.0 125° C Limit 115 ° C Derated Amp 115 ° C Room Temp 2.5 2.4 2.0 2.0 2.1 1.7 1.5 1.2 1.0 1.0 0.5 Useful Range 0.0 20 40 60 80 100 120 140 Ambient Temperature, ° C e. Linear configuration with all adjacent conductors/contacts powered Base Curve TC0928--2600 60(ALL) Contacts in Linear series Part Numbers: HSEC8-160-01-L-RA/PCB-101757-TST Derated 20 % RT Peak Amp RT Derated Amp Measured Current Current Rating per Contact (30 Deg. Rise, 20% Derated) = 0.9 Amps 85 ° C 2.5 85 ° C Peak Amp Room Temp= 24.7 C 85 ° C Derated Amp 95 ° C 95 ° C Peak Amp 2.1 95 ° C Derated Amp Maximum Current, Amp per Contact 2.0 Limit 115 ° C Peak Amp 115 ° C Derated Amp 1.7 115 ° C 125° C Limit 1.5 Room Temp 1.3 1.1 1.0 1.0 0.9 0.6 0.5 0.5 Useful Range 0.0 20 40 60 80 Ambient Temperature, ° C Page 17 of 41 100 120 140 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA CONTACT GAPS: Initial Units: After 100 Cycles Units: inches Minimum 0.028 Maximum 0.035 0.030 Average St. Dev. 0.0015 Count 600 inches 0.018 0.022 0.020 0.0008 600 Minimum Maximum Average St. Dev. Count After Thermal Units: inches Minimum 0.031 Maximum 0.039 0.034 Average St. Dev. 0.0011 Count 600 After Humidity Units: inches Minimum 0.032 Maximum 0.038 0.034 Average St. Dev. 0.0011 Count 600 Dimensional Product Spec: Nominal 0.022 Minimum 0.018 Maximum 0.026 MATING/UNMATING Initial Mating Minimum Maximum Average After 25 Cycles Mating Unmating Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 142.9 207.8 182.6 8.9 13.0 11.4 43.7 60.0 52.3 2.7 3.7 3.3 134.7 189.1 160.0 8.4 11.8 10.0 47.3 61.7 56.8 3.0 3.9 3.5 After 50 Cycles Mating Unmating Force (Oz) Minimum Maximum Average Minimum Maximum Average Force (Lbs) Force (Oz) After 75 Cycles Mating Unmating Force (Lbs) 128.7 173.2 146.9 8.0 48.0 3.0 10.8 61.0 3.8 55.8 9.2 3.5 After 100 Cycles Mating Unmating Force (Oz) Maximum Average Force (Oz) Force (Lbs) 126.3 159.8 143.3 7.9 47.3 2.95 10.0 66.7 4.2 57.4 9.0 3.6 After Thermals Mating Unmating Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 121.3 146.0 133.1 7.6 9.1 8.3 48.7 61.7 54.9 3.0 3.9 3.4 95.6 134.0 117.6 6.0 8.4 7.4 37.4 68.4 53.0 2.3 4.3 3.3 After Humidity Mating Unmating Minimum Force (Lbs) Force (Oz) Force (Lbs) Force (Oz) Force (Lbs) 89.0 119.7 105.8 5.6 7.5 6.6 27.4 48.3 40.4 1.7 3.0 2.5 Page 18 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING): 1) Calibrated force gauges are used along with computer controlled positioning equipment. 2) For Normal force 8-10 measurements are taken and the averages reported. Initial Averages Min Max St. Dev Count Thermal Averages Min Max St. Dev Count 0.005 17.59 15.81 18.89 0.75 15 Deflectio ns in inches Forces 0.010 0.015 36.68 55.55 34.91 53.39 38.20 57.50 1.00 1.14 15 15 in Grams 0.020 73.75 71.63 76.57 1.37 15 SET 0.0004 0.0003 0.0005 0.0001 15 0.005 19.02 16.70 23.10 1.83 15 Deflections in inches, Forces in Grams 0.010 0.015 0.020 39.17 58.77 71.50 36.10 55.80 69.18 41.10 60.40 74.96 1.67 1.61 1.40 15 15 15 SET 0.0021 0.0018 0.0025 0.0002 15 INSULATION RESISTANCE (IR): Pin to Pin Minimum Initial Thermal Humidity Mated HSEC8/PCB 10000 10000 10000 Unmated HSEC8 10000 10000 10000 DIELECTRIC WITHSTANDING VOLTAGE (DWV): Voltage Rating Summary Minimum HSEC8/PCB 700 525 175 Break Down Voltage Test Voltage Working Voltage Pin to Pin Initial Test Voltage After Thermal Test Voltage After Humidity Test Voltage Page 19 of 41 Passed Passed Passed Unmated PCB Not Tested Not Tested Not Tested Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA LLCR: 1) 2) 3) 4) A total of 200 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms ------------------- Unstable f. >+2000 mOhms:---------------------------- Open Failure Date Jul. 16 2009 Room Temp C 23 RH 60% Name Kason He mOhm values Actual Initial Average 7.5 St. Dev. 1.0 Min 5.6 Max 10.3 Count 200 Jul. 16 2009 23 57% Kason He Delta 100 Cycles -0.1 0.7 -2.1 3.2 200 Jul. 31 2009 Aug. 11 2009 23 24 57% 52% Kason He Kason He Delta Delta Thermal Humidity 1.4 1.3 0.9 1.2 -1.2 -1.4 4.3 4.3 200 200 How many samples are being tested? How many contacts are on each board? 100 Cycles Thermal Humidity Stable 200 200 200 Minor 0 0 0 Acceptable Marginal 0 0 0 0 0 0 Page 20 of 41 8 25 Unstable 0 0 0 Open 0 0 0 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA GAS TIGHT: 1) 2) 3) 4) A total of 200 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure Date Jul. 16 2009 Room Temp C 23 RH 60% Name Kason He mOhm values Actual Initial Average 7.6 St. Dev. 0.9 Min 5.9 Max 9.9 Count 200 Jul. 22 2009 23 57% Kason He Delta Gas Tight 0.3 1.0 -3.3 3.5 200 How many samples are being tested? How many contacts are on each board? Gas Tight Stable 200 Minor 0 Acceptable 0 Page 21 of 41 Marginal 0 8 25 Unstable 0 Open 0 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA DATA INSULATION RESISTANCE (IR): Initial Insulation Resistance Measured In Meg Ohms Sample# 1 2 Mated x HSEC8/PCB 10000 10000 Pin to Pin Unmated x HSEC8 10000 10000 PCB Thermal Insulation Resistance Measured In Meg Ohms Sample# 1 2 Mated x HSEC8/PCB 10000 10000 Pin to Pin Unmated x HSEC8 10000 10000 PCB Humidity Insulation Resistance Measured In Meg Ohms Sample# 1 2 Mated x HSEC8/PCB 10000 10000 Pin to Pin Unmated x HSEC8 10000 10000 Page 22 of 41 PCB Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA DIELECTRIC WITHSTANDING VOLTAGE (DWV): Initial Breakdown Voltage Test Voltage Until Breakdown Occurs Mated Sample# 1 2 HSEC8/PCB 750 700 Pin to Pin Unmated X HSEC8 750 750 PCB Initial DWV Test Voltage= 525 Sample# 1 2 Mated HSEC8/PCB 525 525 Pin to Pin Unmated HSEC8 525 525 PCB Thermal Test Voltage Test Voltage= 525 Sample# 1 2 Mated HSEC8/PCB 525 525 Pin to Pin Unmated HSEC8 525 525 PCB Humidity Test Voltage Test Voltage= 525 Sample# 1 2 Mated HSEC8/PCB 525 525 Pin to Pin Unmated HSEC8 525 525 Page 23 of 41 PCB Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA CONTACT GAPS: Initial Units:inches Pos.# B1 B2 B3 0.020 0.020 1 0.020 0.020 2 0.019 0.019 3 0.021 0.021 4 0.020 0.021 5 0.020 0.021 6 0.021 0.020 7 0.019 0.019 8 0.021 0.021 9 0.021 0.021 10 0.021 0.020 11 0.022 0.021 12 0.022 0.021 13 0.022 0.021 14 0.022 0.021 15 0.022 0.021 16 0.021 0.022 17 0.021 0.020 18 0.022 0.021 19 0.020 0.020 20 0.021 0.021 21 0.022 0.022 22 0.021 0.022 23 0.020 0.020 24 0.020 0.020 25 0.022 0.019 26 0.021 0.019 27 0.020 0.020 28 0.021 0.020 29 0.021 0.020 30 0.020 0.020 31 0.020 0.020 32 0.020 0.021 33 0.021 0.020 34 0.021 0.020 35 0.020 0.020 36 0.020 0.020 37 0.020 0.019 38 0.020 0.019 39 0.020 0.019 40 0.020 0.020 41 0.019 0.018 42 0.019 0.019 43 0.021 0.020 44 B4 0.021 0.021 0.021 0.020 0.020 0.020 0.019 0.020 0.020 0.020 0.021 0.021 0.021 0.021 0.020 0.020 0.020 0.022 0.020 0.020 0.020 0.020 0.020 0.019 0.020 0.021 0.021 0.019 0.019 0.019 0.019 0.020 0.020 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 0.019 B5 0.020 0.020 0.020 0.021 0.021 0.021 0.021 0.019 0.021 0.021 0.020 0.021 0.021 0.020 0.020 0.021 0.021 0.020 0.021 0.021 0.021 0.021 0.021 0.021 0.021 0.020 0.021 0.019 0.020 0.020 0.021 0.019 0.022 0.020 0.020 0.020 0.020 0.019 0.020 0.020 0.021 0.019 0.020 0.021 B6 0.019 0.019 0.018 0.020 0.020 0.020 0.020 0.019 0.020 0.021 0.021 0.021 0.021 0.020 0.020 0.021 0.021 0.020 0.021 0.021 0.021 0.021 0.021 0.020 0.020 0.020 0.019 0.020 0.020 0.019 0.019 0.019 0.022 0.020 0.020 0.020 0.021 0.019 0.021 0.020 0.021 0.019 0.020 0.021 Page 24 of 41 B7 0.019 0.020 0.020 0.022 0.020 0.020 0.021 0.019 0.021 0.022 0.021 0.021 0.021 0.021 0.021 0.021 0.022 0.020 0.020 0.020 0.020 0.021 0.021 0.020 0.020 0.020 0.019 0.020 0.019 0.019 0.019 0.020 0.021 0.021 0.021 0.021 0.021 0.020 0.021 0.020 0.021 0.019 0.019 0.021 B8 0.019 0.019 0.019 0.022 0.021 0.021 0.021 0.020 0.020 0.021 0.020 0.020 0.021 0.020 0.020 0.020 0.021 0.019 0.020 0.021 0.020 0.020 0.020 0.019 0.020 0.020 0.021 0.019 0.020 0.020 0.021 0.020 0.021 0.021 0.021 0.020 0.021 0.019 0.020 0.020 0.020 0.019 0.019 0.020 B9 0.019 0.019 0.019 0.021 0.020 0.020 0.021 0.019 0.021 0.021 0.021 0.022 0.022 0.022 0.021 0.021 0.022 0.020 0.022 0.020 0.020 0.021 0.021 0.021 0.021 0.021 0.019 0.020 0.021 0.021 0.020 0.021 0.021 0.021 0.021 0.021 0.020 0.020 0.020 0.021 0.021 0.019 0.019 0.020 B10 0.019 0.019 0.019 0.021 0.020 0.020 0.020 0.019 0.021 0.021 0.020 0.021 0.022 0.021 0.021 0.021 0.022 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.020 0.019 0.019 0.020 0.019 0.020 0.019 0.020 0.020 0.020 0.020 0.020 0.020 0.019 0.020 0.020 0.020 0.019 0.019 0.020 0.020 0.020 0.019 0.021 0.020 0.021 0.021 0.019 0.021 0.021 0.021 0.022 0.021 0.021 0.021 0.021 0.022 0.020 0.021 0.021 0.020 0.021 0.021 0.020 0.020 0.019 0.018 0.021 0.020 0.020 0.019 0.021 0.020 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 0.019 0.019 45 0.019 0.020 46 0.020 0.020 47 0.019 0.019 48 0.019 0.019 49 0.020 0.019 50 0.020 0.019 51 0.019 0.019 52 0.019 0.019 53 0.019 0.019 54 0.019 0.019 55 0.020 0.019 56 0.020 0.020 57 0.019 0.019 58 0.019 0.020 59 0.020 0.020 60 After 100 Cycles Units:inches Pos.# B1 B2 B3 0.033 0.033 1 0.032 0.031 2 0.030 0.030 3 0.030 0.030 4 0.030 0.028 5 0.029 0.028 6 0.030 0.029 7 0.032 0.028 8 0.030 0.030 9 0.031 0.030 10 0.030 0.032 11 0.032 0.030 12 0.031 0.029 13 0.028 0.030 14 0.029 0.029 15 0.033 0.034 16 0.029 0.034 17 0.032 0.029 18 0.033 0.029 19 0.029 0.030 20 0.035 0.029 21 0.029 0.031 22 0.028 0.029 23 0.033 0.031 24 0.030 0.030 25 0.033 0.030 26 0.032 0.029 27 0.030 0.029 28 0.029 0.030 29 0.030 0.031 30 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 0.019 0.020 0.019 0.019 0.019 0.019 0.019 0.020 0.021 0.021 0.020 0.020 0.020 0.020 0.020 0.018 0.020 0.019 0.019 0.019 0.019 0.019 0.020 B4 0.031 0.032 0.032 0.030 0.030 0.030 0.029 0.030 0.029 0.030 0.032 0.031 0.030 0.031 0.033 0.029 0.031 0.031 0.030 0.028 0.031 0.030 0.030 0.030 0.030 0.032 0.030 0.033 0.030 0.030 0.020 0.021 0.021 0.020 0.020 0.020 0.020 0.020 0.019 0.020 0.020 0.020 0.020 0.019 0.020 0.020 B5 0.032 0.032 0.030 0.031 0.029 0.031 0.030 0.029 0.030 0.029 0.029 0.030 0.029 0.028 0.034 0.030 0.029 0.029 0.029 0.033 0.030 0.030 0.031 0.031 0.029 0.033 0.034 0.028 0.029 0.031 Part #: HSEC8-160-01-L-RA 0.020 0.020 0.021 0.020 0.020 0.020 0.020 0.020 0.019 0.020 0.020 0.020 0.020 0.019 0.019 0.020 B6 0.034 0.032 0.031 0.031 0.030 0.030 0.030 0.029 0.030 0.030 0.029 0.029 0.031 0.029 0.029 0.030 0.030 0.033 0.033 0.029 0.029 0.030 0.030 0.029 0.028 0.030 0.029 0.029 0.029 0.030 Page 25 of 41 0.019 0.019 0.020 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 0.019 0.019 0.019 0.020 B7 0.030 0.030 0.031 0.030 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.030 0.029 0.029 0.030 0.029 0.030 0.029 0.029 0.029 0.030 0.029 0.029 0.030 0.030 0.029 0.030 0.030 0.032 0.033 0.020 0.020 0.020 0.019 0.020 0.019 0.019 0.019 0.019 0.020 0.019 0.020 0.020 0.019 0.019 0.020 B8 0.030 0.032 0.032 0.030 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.029 0.030 0.030 0.031 0.032 0.019 0.019 0.020 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 B9 0.034 0.033 0.033 0.032 0.031 0.031 0.030 0.030 0.030 0.030 0.030 0.030 0.029 0.030 0.030 0.030 0.030 0.030 0.029 0.029 0.030 0.029 0.028 0.030 0.030 0.030 0.031 0.030 0.032 0.034 0.019 0.019 0.020 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.019 0.020 0.019 0.019 0.020 B10 0.032 0.032 0.032 0.031 0.034 0.030 0.029 0.028 0.030 0.030 0.030 0.029 0.029 0.030 0.030 0.030 0.031 0.029 0.030 0.030 0.031 0.032 0.030 0.030 0.031 0.030 0.030 0.030 0.031 0.033 0.033 0.032 0.033 0.032 0.031 0.031 0.031 0.030 0.030 0.030 0.031 0.030 0.030 0.029 0.030 0.030 0.031 0.029 0.029 0.030 0.030 0.029 0.029 0.029 0.029 0.030 0.030 0.030 0.032 0.032 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 0.032 0.031 31 0.031 0.032 32 0.032 0.032 33 0.030 0.031 34 0.029 0.030 35 0.031 0.030 36 0.029 0.030 37 0.028 0.029 38 0.029 0.030 39 0.029 0.030 40 0.030 0.030 41 0.029 0.029 42 0.030 0.029 43 0.029 0.029 44 0.029 0.030 45 0.028 0.029 46 0.030 0.030 47 0.028 0.030 48 0.030 0.028 49 0.028 0.029 50 0.029 0.029 51 0.028 0.028 52 0.028 0.028 53 0.029 0.029 54 0.029 0.029 55 0.029 0.029 56 0.030 0.030 57 0.029 0.030 58 0.032 0.031 59 0.033 0.033 60 After Thermal Units:inches Pos.# B1 B2 B3 0.036 0.037 1 0.035 0.036 2 0.034 0.034 3 0.034 0.034 4 0.033 0.033 5 0.032 0.033 6 0.034 0.033 7 0.032 0.032 8 0.033 0.033 9 0.034 0.034 10 0.034 0.033 11 0.033 0.032 12 0.034 0.033 13 0.033 0.033 14 0.033 0.032 15 0.034 0.033 16 0.033 0.031 0.031 0.030 0.031 0.030 0.029 0.029 0.030 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.029 0.028 0.029 0.028 0.030 0.029 0.030 0.030 0.032 0.030 0.030 0.033 0.033 0.033 0.031 0.030 0.032 0.030 0.030 0.030 0.029 0.028 0.029 0.029 0.030 0.029 0.029 0.030 0.030 0.030 0.030 0.029 0.029 0.029 0.029 0.028 0.028 0.029 0.029 0.031 0.030 0.030 0.034 0.033 B4 0.035 0.036 0.036 0.034 0.034 0.034 0.033 0.033 0.034 0.033 0.035 0.033 0.033 0.034 0.035 0.034 0.030 0.030 0.032 0.030 0.030 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.030 0.030 0.030 0.028 0.029 0.029 0.029 0.029 0.028 0.029 0.029 0.029 0.030 0.029 0.031 0.032 B5 0.035 0.035 0.034 0.034 0.034 0.034 0.033 0.032 0.033 0.033 0.033 0.033 0.033 0.032 0.031 0.033 Part #: HSEC8-160-01-L-RA 0.033 0.032 0.030 0.031 0.030 0.031 0.031 0.029 0.030 0.031 0.030 0.030 0.030 0.029 0.029 0.030 0.030 0.030 0.029 0.030 0.029 0.030 0.030 0.029 0.034 0.034 0.030 0.029 0.030 0.030 B6 0.037 0.036 0.034 0.035 0.035 0.034 0.034 0.033 0.034 0.035 0.034 0.033 0.034 0.033 0.032 0.033 Page 26 of 41 0.035 0.033 0.031 0.032 0.031 0.031 0.031 0.030 0.030 0.031 0.030 0.030 0.031 0.029 0.029 0.030 0.030 0.029 0.030 0.029 0.030 0.030 0.034 0.029 0.030 0.031 0.034 0.030 0.031 0.032 B7 0.037 0.036 0.034 0.035 0.035 0.034 0.034 0.033 0.034 0.035 0.034 0.033 0.034 0.032 0.033 0.033 0.034 0.033 0.030 0.032 0.030 0.030 0.031 0.028 0.030 0.031 0.030 0.032 0.031 0.030 0.031 0.031 0.030 0.034 0.030 0.029 0.034 0.031 0.031 0.031 0.033 0.031 0.030 0.030 0.031 0.030 B8 0.037 0.036 0.038 0.036 0.036 0.035 0.035 0.033 0.033 0.035 0.034 0.033 0.034 0.032 0.032 0.033 0.033 0.032 0.033 0.032 0.035 0.030 0.031 0.034 0.029 0.030 0.034 0.030 0.031 0.029 0.033 0.034 0.031 0.033 0.034 0.034 0.034 0.034 0.034 0.034 0.034 0.034 0.033 0.034 0.034 0.034 B9 0.039 0.037 0.035 0.037 0.035 0.035 0.035 0.034 0.035 0.035 0.034 0.034 0.035 0.033 0.033 0.034 0.029 0.029 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.028 0.029 0.031 0.032 0.030 0.030 0.031 0.030 0.029 0.030 0.029 0.030 0.030 0.030 0.029 0.028 0.029 0.029 0.030 0.029 0.029 B10 0.038 0.035 0.034 0.035 0.034 0.034 0.033 0.032 0.034 0.035 0.034 0.034 0.035 0.034 0.033 0.035 0.037 0.036 0.034 0.035 0.035 0.035 0.035 0.033 0.034 0.035 0.034 0.034 0.034 0.033 0.033 0.034 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 0.034 0.033 17 0.033 0.033 18 0.033 0.033 19 0.034 0.033 20 0.034 0.033 21 0.034 0.033 22 0.034 0.032 23 0.034 0.032 24 0.034 0.033 25 0.034 0.034 26 0.034 0.033 27 0.034 0.033 28 0.034 0.033 29 0.035 0.034 30 0.035 0.034 31 0.035 0.035 32 0.036 0.035 33 0.035 0.034 34 0.034 0.033 35 0.035 0.034 36 0.034 0.032 37 0.033 0.032 38 0.034 0.033 39 0.034 0.033 40 0.034 0.034 41 0.033 0.033 42 0.033 0.033 43 0.034 0.033 44 0.034 0.033 45 0.033 0.032 46 0.034 0.034 47 0.033 0.033 48 0.033 0.033 49 0.033 0.033 50 0.034 0.033 51 0.033 0.032 52 0.033 0.033 53 0.034 0.033 54 0.034 0.033 55 0.034 0.033 56 0.035 0.034 57 0.034 0.034 58 0.036 0.036 59 0.036 0.036 60 After Humidity Units:inches Pos.# B1 B2 B3 0.033 0.033 1 0.032 0.031 2 0.034 0.035 0.034 0.032 0.034 0.034 0.034 0.034 0.033 0.035 0.034 0.034 0.035 0.033 0.035 0.035 0.035 0.035 0.035 0.034 0.034 0.034 0.033 0.033 0.033 0.034 0.034 0.034 0.034 0.033 0.034 0.033 0.033 0.033 0.033 0.033 0.034 0.035 0.036 0.034 0.035 0.035 0.037 0.036 0.033 0.033 0.033 0.033 0.033 0.034 0.034 0.034 0.033 0.033 0.033 0.033 0.033 0.034 0.035 0.034 0.036 0.034 0.034 0.034 0.033 0.033 0.033 0.033 0.034 0.033 0.033 0.034 0.034 0.034 0.034 0.033 0.033 0.034 0.034 0.033 0.033 0.033 0.034 0.034 0.035 0.034 0.036 0.037 B4 0.031 0.032 0.033 0.034 0.033 0.033 0.033 0.034 0.034 0.033 0.034 0.033 0.032 0.033 0.033 0.033 0.034 0.034 0.035 0.034 0.033 0.034 0.033 0.032 0.033 0.033 0.033 0.032 0.033 0.033 0.033 0.034 0.034 0.033 0.033 0.033 0.034 0.033 0.033 0.034 0.034 0.034 0.035 0.034 0.036 0.037 B5 0.032 0.032 Part #: HSEC8-160-01-L-RA 0.033 0.033 0.032 0.032 0.033 0.033 0.033 0.032 0.032 0.033 0.033 0.033 0.033 0.033 0.034 0.034 0.035 0.034 0.033 0.034 0.033 0.033 0.033 0.033 0.034 0.033 0.033 0.034 0.034 0.033 0.034 0.033 0.033 0.034 0.034 0.033 0.033 0.034 0.034 0.034 0.035 0.035 0.036 0.037 B6 0.034 0.032 Page 27 of 41 0.034 0.034 0.033 0.034 0.033 0.034 0.034 0.034 0.033 0.033 0.034 0.034 0.034 0.035 0.036 0.036 0.036 0.036 0.036 0.035 0.035 0.034 0.035 0.035 0.035 0.034 0.034 0.034 0.034 0.034 0.035 0.034 0.034 0.034 0.035 0.033 0.034 0.034 0.034 0.035 0.035 0.035 0.036 0.037 B7 0.030 0.030 0.034 0.034 0.034 0.032 0.033 0.034 0.034 0.034 0.034 0.034 0.034 0.034 0.035 0.036 0.036 0.036 0.037 0.036 0.035 0.035 0.034 0.034 0.034 0.035 0.035 0.034 0.034 0.034 0.034 0.033 0.034 0.033 0.033 0.034 0.035 0.033 0.033 0.034 0.034 0.034 0.035 0.035 0.037 0.038 B8 0.030 0.032 0.034 0.034 0.033 0.033 0.034 0.034 0.034 0.034 0.033 0.034 0.034 0.034 0.033 0.034 0.035 0.035 0.035 0.035 0.034 0.034 0.033 0.032 0.033 0.034 0.034 0.033 0.033 0.034 0.035 0.034 0.035 0.033 0.034 0.035 0.035 0.034 0.034 0.034 0.035 0.034 0.035 0.034 0.036 0.036 B9 0.034 0.033 0.034 0.034 0.033 0.034 0.033 0.034 0.034 0.034 0.034 0.033 0.033 0.034 0.034 0.034 0.035 0.035 0.036 0.034 0.033 0.034 0.033 0.032 0.033 0.033 0.034 0.033 0.033 0.033 0.034 0.033 0.034 0.032 0.033 0.034 0.034 0.033 0.032 0.034 0.034 0.034 0.035 0.034 0.036 0.036 B10 0.032 0.032 0.033 0.032 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 0.030 0.030 0.030 0.029 0.030 0.032 0.030 0.031 0.030 0.032 0.031 0.028 0.029 0.033 0.029 0.032 0.033 0.029 0.035 0.029 0.028 0.033 0.030 0.033 0.032 0.030 0.029 0.030 0.032 0.031 0.032 0.030 0.029 0.031 0.029 0.028 0.029 0.029 0.030 0.029 0.030 0.029 0.029 0.028 0.030 0.028 0.030 0.028 0.029 0.030 0.030 0.028 0.028 0.029 0.028 0.030 0.030 0.032 0.030 0.029 0.030 0.029 0.034 0.034 0.029 0.029 0.030 0.029 0.031 0.029 0.031 0.030 0.030 0.029 0.029 0.030 0.031 0.031 0.032 0.032 0.031 0.030 0.030 0.030 0.029 0.030 0.030 0.030 0.029 0.029 0.029 0.030 0.029 0.030 0.030 0.028 0.029 0.029 0.032 0.030 0.030 0.030 0.029 0.030 0.029 0.030 0.032 0.031 0.030 0.031 0.033 0.029 0.031 0.031 0.030 0.028 0.031 0.030 0.030 0.030 0.030 0.032 0.030 0.033 0.030 0.030 0.033 0.031 0.031 0.030 0.031 0.030 0.029 0.029 0.030 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.029 0.028 0.029 0.028 0.030 0.030 0.031 0.029 0.031 0.030 0.029 0.030 0.029 0.029 0.030 0.029 0.028 0.034 0.030 0.029 0.029 0.029 0.033 0.030 0.030 0.031 0.031 0.029 0.033 0.034 0.028 0.029 0.031 0.031 0.030 0.032 0.030 0.030 0.030 0.029 0.028 0.029 0.029 0.030 0.029 0.029 0.030 0.030 0.030 0.030 0.029 0.029 0.029 0.029 0.031 0.031 0.030 0.030 0.030 0.029 0.030 0.030 0.029 0.029 0.031 0.029 0.029 0.030 0.030 0.033 0.033 0.029 0.029 0.030 0.030 0.029 0.028 0.030 0.029 0.029 0.029 0.030 0.030 0.030 0.032 0.030 0.030 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.030 0.030 0.030 0.028 0.029 0.029 0.029 Page 28 of 41 Part #: HSEC8-160-01-L-RA 0.031 0.030 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.030 0.029 0.029 0.030 0.029 0.030 0.029 0.029 0.029 0.030 0.029 0.029 0.030 0.030 0.029 0.030 0.030 0.032 0.033 0.033 0.032 0.030 0.031 0.030 0.031 0.031 0.029 0.030 0.031 0.030 0.030 0.030 0.029 0.029 0.030 0.030 0.030 0.029 0.030 0.029 0.032 0.030 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.028 0.029 0.029 0.029 0.028 0.029 0.029 0.029 0.030 0.030 0.031 0.032 0.035 0.033 0.031 0.032 0.031 0.031 0.031 0.030 0.030 0.031 0.030 0.030 0.031 0.029 0.029 0.030 0.030 0.029 0.030 0.029 0.030 0.033 0.032 0.031 0.031 0.030 0.030 0.030 0.030 0.030 0.030 0.029 0.030 0.030 0.030 0.030 0.030 0.029 0.029 0.030 0.029 0.028 0.030 0.030 0.030 0.031 0.030 0.032 0.034 0.034 0.033 0.030 0.032 0.030 0.030 0.031 0.028 0.030 0.031 0.030 0.032 0.031 0.030 0.031 0.031 0.030 0.034 0.030 0.029 0.034 0.032 0.031 0.034 0.030 0.029 0.028 0.030 0.030 0.030 0.029 0.029 0.030 0.030 0.030 0.031 0.029 0.030 0.030 0.031 0.032 0.030 0.030 0.031 0.030 0.030 0.030 0.031 0.033 0.033 0.032 0.033 0.032 0.035 0.030 0.031 0.034 0.029 0.030 0.034 0.030 0.031 0.029 0.033 0.034 0.031 0.033 0.034 0.034 0.034 0.033 0.032 0.031 0.031 0.031 0.030 0.030 0.030 0.031 0.030 0.030 0.029 0.030 0.030 0.031 0.029 0.029 0.030 0.030 0.029 0.029 0.029 0.029 0.030 0.030 0.030 0.032 0.032 0.029 0.029 0.028 0.029 0.029 0.029 0.029 0.030 0.029 0.028 0.029 0.031 0.032 0.030 0.030 0.031 0.030 0.029 0.030 0.029 0.030 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 52 53 54 55 56 57 58 59 60 0.028 0.028 0.029 0.029 0.029 0.030 0.029 0.032 0.033 0.028 0.028 0.029 0.029 0.029 0.030 0.030 0.031 0.033 0.029 0.030 0.030 0.032 0.030 0.030 0.033 0.033 0.033 0.028 0.028 0.029 0.029 0.031 0.030 0.030 0.034 0.033 0.029 0.028 0.029 0.029 0.029 0.030 0.029 0.031 0.032 Page 29 of 41 Part #: HSEC8-160-01-L-RA 0.030 0.030 0.029 0.034 0.034 0.030 0.029 0.030 0.030 0.030 0.034 0.029 0.030 0.031 0.034 0.030 0.031 0.032 0.031 0.031 0.031 0.033 0.031 0.030 0.030 0.031 0.030 0.034 0.034 0.034 0.034 0.034 0.033 0.034 0.034 0.034 0.030 0.030 0.029 0.028 0.029 0.029 0.030 0.029 0.029 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA Mating—Unmating Initial Sample # 1 2 3 4 5 6 7 8 9 10 After 25 Cycles After 50 Cycles After 75 Cycles Mating Unmating Mating Unmating Mating Unmating Mating Unmating 8.93 11.90 12.39 12.57 10.85 10.63 12.99 10.27 12.87 10.74 2.91 3.48 3.48 3.53 2.73 2.98 3.73 3.13 3.75 3.00 8.42 11.82 10.41 9.77 9.99 8.80 9.66 9.33 11.66 10.14 3.02 3.57 3.75 3.66 2.95 3.73 3.62 3.68 3.64 3.86 8.53 9.61 9.44 8.86 8.86 9.46 8.05 8.51 10.82 9.66 3.00 3.55 3.53 3.64 3.09 3.81 3.37 3.53 3.59 3.75 8.05 9.57 9.99 9.24 8.69 8.80 8.14 7.89 9.92 9.30 2.95 3.95 3.66 4.17 3.24 3.51 3.37 3.42 3.79 3.79 After 100 Cycles Sample # 1 2 3 4 5 6 7 8 9 10 After Thermals After Humidity Mating Unmating Mating Unmating Mating Unmating 7.87 8.27 9.13 8.69 8.51 8.29 7.89 8.99 7.58 7.98 3.04 3.22 3.57 3.86 3.33 3.40 3.28 3.62 3.42 3.55 5.97 7.58 8.38 8.29 7.03 7.17 6.04 7.17 8.18 7.72 2.34 3.11 3.84 4.28 2.73 3.33 2.82 3.35 3.73 3.59 5.56 6.41 6.96 7.05 6.90 1.71 1.99 2.51 2.98 2.46 6.49 6.05 6.62 7.48 6.62 2.64 2.37 3.00 3.02 2.57 Page 30 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA NORMAL FORCE: Initial Initial Sample # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0.005 18.48 17.66 18.28 17.66 17.66 17.66 18.28 17.46 18.89 17.25 17.25 15.81 16.64 17.66 17.25 Deflections in inches Forces in Grams 0.010 0.015 0.020 SET 37.28 56.47 74.20 0.00040 37.17 55.86 74.45 0.00040 38.20 57.29 74.51 0.00050 37.17 56.06 74.90 0.00040 37.79 57.50 76.57 0.00050 37.38 56.47 75.71 0.00050 37.38 55.45 72.98 0.00030 36.25 55.24 73.07 0.00040 37.58 56.27 73.87 0.00050 35.94 54.62 73.89 0.00030 36.14 54.83 73.50 0.00030 34.91 53.39 72.21 0.00030 35.73 54.62 72.13 0.00040 36.14 54.83 72.57 0.00040 35.12 54.42 71.63 0.00030 0.005 18.80 20.40 20.10 23.10 20.40 20.70 20.40 17.30 17.00 19.40 18.80 16.70 17.30 17.60 17.30 Deflections in inches Forces in Grams 0.010 0.015 0.020 SET 39.80 60.10 73.22 0.00250 40.70 60.40 72.13 0.00230 40.70 60.40 72.33 0.00230 40.70 60.40 74.96 0.00220 40.70 60.40 71.92 0.00230 41.10 60.10 71.89 0.00230 40.40 59.50 71.66 0.00240 37.60 57.90 71.20 0.00180 36.70 56.40 69.79 0.00180 40.10 58.90 71.10 0.00230 39.20 58.90 71.37 0.00210 36.10 55.80 69.18 0.00180 37.60 57.00 70.79 0.00200 38.50 58.30 70.68 0.00200 37.60 57.00 70.33 0.00190 After thermal Thermal Sample # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Page 31 of 41 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA LLCR: Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 Actual Initial 6.3 6.6 6.4 6.7 5.9 8.3 7.9 8.1 8.4 8.3 8.4 8.4 8.2 8.2 8.7 8.4 8.6 8.3 8.3 6.0 6.2 6.8 6.6 7.3 7.3 6.1 6.1 6.2 6.4 6.5 8.0 8.0 8.4 8.0 8.1 7.9 7.6 8.6 7.9 9.5 7.8 7.9 8.0 8.1 Delta 100 Cycles 0.1 0.0 0.1 -0.1 0.2 -0.2 0.0 -0.2 -0.1 -0.4 -0.1 0.1 -0.1 -0.3 -0.7 -0.4 -0.4 0.0 -0.5 0.2 0.3 -0.5 -0.7 -0.8 -0.6 0.5 0.1 0.2 -0.2 -0.5 1.1 -0.1 -0.3 0.0 0.0 0.1 0.3 -0.3 -0.2 -1.8 0.1 -0.3 -0.2 0.1 Page 32 of 41 Delta Thermal 1.3 0.7 1.8 0.5 1.0 2.0 1.2 1.0 0.8 1.3 1.0 1.4 1.2 1.1 0.8 1.0 1.2 1.5 1.1 0.7 1.1 0.3 1.4 0.7 2.5 4.0 2.5 2.8 0.9 2.4 1.4 1.1 0.5 0.8 1.7 1.4 1.8 1.2 0.8 0.0 0.5 1.6 1.0 0.9 Delta Humidity 1.5 0.7 0.3 0.7 0.6 2.3 1.0 -0.5 0.7 2.2 1.4 2.1 1.5 2.0 1.4 0.8 0.0 2.3 0.0 2.7 0.8 -0.4 0.3 -0.4 2.1 2.6 2.5 2.7 3.4 -0.2 1.0 1.3 2.1 0.1 1.6 1.3 1.3 2.0 0.3 -0.1 2.8 1.9 2.2 1.7 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 6.1 5.9 6.0 6.1 6.3 6.3 6.6 6.7 6.9 6.4 6.1 7.9 7.9 8.0 8.2 8.4 7.8 8.1 8.2 8.4 8.5 7.8 7.9 7.7 8.2 6.4 6.4 6.6 7.3 6.8 6.2 6.5 6.4 6.5 6.8 6.0 8.2 8.6 8.1 8.0 8.6 8.3 8.9 9.2 8.6 8.2 9.0 8.9 8.4 0.1 0.7 0.4 0.0 0.2 0.5 1.6 0.1 -0.8 -0.2 0.2 0.4 -0.2 0.0 -0.3 -0.2 0.4 0.3 0.3 -0.5 -0.7 0.0 -0.4 0.0 -0.5 0.0 0.2 0.4 -0.8 0.4 3.2 -0.3 0.7 -0.1 0.0 0.7 -0.1 -0.1 0.1 0.0 -0.7 -0.2 -0.7 -1.0 -0.4 -0.1 -0.9 -0.9 -0.5 Page 33 of 41 Part #: HSEC8-160-01-L-RA 2.5 4.3 2.6 1.0 1.3 3.8 1.6 0.8 0.2 0.8 1.0 2.5 2.0 2.2 1.1 1.7 2.5 2.1 2.1 1.6 1.5 1.3 1.2 2.6 1.6 2.1 3.3 1.2 0.2 1.7 2.2 2.5 1.2 0.8 0.7 1.6 1.3 1.3 1.7 2.2 0.9 1.6 1.9 0.1 0.8 1.2 -0.1 0.0 0.8 2.7 2.9 2.7 2.0 0.4 4.0 3.8 -0.1 1.3 2.2 2.0 1.4 -0.3 2.7 -0.3 2.1 1.7 1.2 1.3 1.8 -0.3 0.8 0.1 0.4 0.2 2.1 2.1 2.0 0.7 0.6 3.4 2.7 3.9 1.4 3.7 0.4 -0.1 0.5 2.2 0.9 1.8 -0.2 1.0 0.2 1.6 2.3 0.6 -0.3 0.2 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 8.6 5.6 6.7 6.5 6.7 6.2 7.1 6.2 6.3 6.5 6.2 6.1 7.7 7.7 8.1 8.3 8.8 7.9 8.1 8.2 8.6 7.8 7.8 7.7 7.6 7.9 5.8 6.3 6.1 6.7 6.6 6.4 7.0 8.0 7.0 7.3 6.1 8.6 8.2 8.1 8.7 8.8 9.3 8.2 8.3 8.5 8.0 8.6 8.9 -0.4 0.5 0.1 0.5 -0.4 0.4 -0.4 1.3 0.1 -0.4 0.2 0.2 0.7 -0.2 0.1 0.0 -1.4 0.2 -0.5 -0.2 -1.1 -0.4 0.3 0.0 -0.2 0.1 1.7 0.1 0.3 -0.4 -0.3 0.2 -0.4 -1.9 -0.1 -0.7 -0.2 0.0 0.1 0.1 -0.8 -0.3 -1.0 -0.3 0.3 0.2 0.6 0.9 0.1 Page 34 of 41 Part #: HSEC8-160-01-L-RA 0.9 1.3 0.9 0.6 1.0 1.3 0.5 1.5 1.6 0.5 2.0 0.8 2.6 1.6 0.6 0.4 0.2 0.9 0.6 1.4 1.5 2.0 1.0 2.9 1.7 2.0 3.8 2.9 2.2 1.0 0.4 1.5 1.8 -0.1 2.1 1.2 2.2 1.8 0.8 0.5 0.9 0.4 0.0 0.7 0.6 1.5 1.2 1.8 0.1 1.6 4.3 2.4 4.0 2.3 3.2 2.6 3.1 1.6 0.0 0.8 0.4 1.9 1.3 -0.3 0.8 -0.3 0.6 1.9 0.2 -0.3 0.3 1.5 0.9 1.6 1.0 2.0 2.2 0.9 0.8 -0.4 1.5 2.6 3.1 0.8 0.4 3.8 0.4 0.4 0.7 -0.4 0.1 -0.3 0.3 2.4 0.7 -1.2 0.8 0.9 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 8.3 8.1 6.3 6.3 6.1 6.4 6.5 6.4 6.8 6.7 7.0 6.7 7.2 9.6 8.5 8.3 8.3 8.2 8.0 8.2 8.4 8.2 8.9 8.3 8.4 8.1 8.9 7.4 7.6 8.3 7.6 7.8 6.8 6.8 6.8 6.4 6.5 6.2 7.8 7.9 7.9 8.5 8.1 7.9 10.3 8.5 7.9 8.0 7.8 -0.2 -0.3 0.6 -0.2 0.6 -0.3 1.6 0.0 -0.6 -0.3 -0.2 -0.2 -0.5 -1.9 -0.6 -0.2 -0.3 0.1 0.5 0.2 -0.4 -0.3 -0.6 -0.2 -0.4 0.2 -1.1 -1.2 -0.3 -1.7 -1.6 -1.1 1.3 -0.4 0.1 0.1 0.0 -0.1 -1.0 0.3 -0.9 -0.3 0.1 -0.5 -2.1 -1.6 -1.4 0.5 0.5 Page 35 of 41 Part #: HSEC8-160-01-L-RA 1.0 1.5 1.1 2.8 1.8 1.2 0.7 2.2 0.5 1.2 0.1 0.7 0.3 -0.5 0.5 1.8 1.3 1.2 2.0 0.9 1.2 0.7 0.0 1.5 1.8 0.5 0.0 0.7 1.3 -1.2 -0.5 -0.1 2.1 2.3 2.4 2.9 3.0 2.8 1.3 1.1 2.2 1.2 1.3 2.1 -1.2 1.2 1.0 0.9 2.0 0.5 0.5 3.6 1.1 2.8 2.9 1.7 0.4 2.0 3.2 1.7 1.4 1.0 -1.0 0.2 0.4 0.4 0.5 1.4 2.2 1.0 0.5 -0.6 1.5 1.4 0.4 2.3 3.8 2.7 -0.5 2.3 -0.6 1.1 2.9 1.2 1.9 2.0 2.1 2.1 0.2 0.4 0.6 1.4 1.3 -1.4 0.8 0.7 0.7 1.2 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 8 8 8 8 8 8 8 8 8 P17 P18 P19 P20 P21 P22 P23 P24 P25 8.0 7.5 8.3 6.3 6.6 6.7 6.5 6.4 6.8 Part #: HSEC8-160-01-L-RA -1.4 2.0 -0.4 1.6 0.7 -0.3 0.0 0.2 -0.2 2.2 1.0 0.6 2.6 2.2 2.2 2.5 3.0 2.8 Actual Initial 6.2 6.0 6.5 6.5 6.0 8.0 8.2 8.2 8.3 8.5 8.6 8.6 8.4 8.3 8.5 8.4 8.4 8.4 8.6 6.8 7.4 6.5 6.3 6.2 8.5 7.0 6.7 6.9 6.7 6.7 8.3 8.5 8.3 Delta Gas Tight -0.1 0.2 -0.3 -0.2 0.1 0.4 -0.4 -0.1 0.7 0.2 0.1 0.5 0.2 0.3 0.0 -0.6 -0.3 -0.6 0.0 -0.8 -0.7 0.3 0.0 0.5 -0.2 0.7 1.1 1.0 0.1 0.2 0.8 0.0 0.1 GAS TIGHT Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 Page 36 of 41 3.3 1.6 0.4 2.5 2.3 0.5 1.1 1.6 2.1 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 8.4 8.2 8.2 8.7 8.5 8.1 8.7 8.8 8.3 8.2 8.3 6.8 6.6 6.6 7.4 6.8 7.0 7.1 8.5 6.8 8.0 6.1 7.9 8.3 8.0 7.7 7.8 8.2 8.0 8.3 8.0 8.0 7.7 7.8 7.8 7.9 6.1 6.4 6.6 6.0 7.0 6.3 6.5 6.8 6.0 6.1 6.3 8.3 8.2 Page 37 of 41 Part #: HSEC8-160-01-L-RA -0.2 0.2 1.0 0.6 0.7 1.4 0.3 -0.2 0.3 0.2 0.2 -0.3 0.3 0.1 0.1 0.4 0.9 -0.2 -1.5 0.3 -1.2 0.6 0.0 0.1 -0.1 1.3 -0.2 -0.1 0.3 0.4 0.0 -0.2 -0.1 0.0 -0.1 0.4 0.1 0.8 0.8 0.5 0.0 1.4 0.7 -0.6 -0.2 1.1 -0.4 -0.2 0.6 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 8.3 8.1 7.9 8.0 8.2 8.4 8.1 8.8 8.9 8.4 7.7 8.1 6.0 6.9 6.5 6.6 5.9 6.3 7.2 6.4 7.1 7.2 6.5 8.5 8.0 9.1 8.7 8.3 8.3 8.1 8.5 8.4 8.5 9.0 8.3 8.4 8.3 6.8 7.0 7.1 6.6 7.3 7.0 6.8 6.5 6.5 6.6 6.1 8.7 Page 38 of 41 Part #: HSEC8-160-01-L-RA 1.8 0.3 1.1 2.1 -0.1 0.1 1.3 0.1 -0.8 -0.1 0.2 0.2 0.3 0.0 -0.4 -0.1 0.0 -0.3 -0.5 1.1 0.0 1.9 0.0 -0.4 0.0 -1.0 -0.8 -0.4 0.1 0.3 -0.3 0.1 0.3 -0.6 -0.5 -0.3 -0.3 -0.7 -0.3 -0.4 0.7 -0.1 1.0 0.7 0.1 -0.3 -0.3 -0.3 -0.7 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P1 P2 P3 P4 P5 7.9 7.5 8.3 7.8 9.1 8.6 9.5 8.0 8.6 8.1 8.0 8.8 8.2 7.1 6.5 6.7 6.7 7.1 7.6 8.4 6.6 7.7 7.2 9.5 7.6 7.7 7.9 7.7 8.3 8.3 7.8 8.3 8.3 8.4 8.3 7.8 8.2 8.2 6.4 7.0 7.3 7.2 7.9 9.9 6.8 6.5 6.7 6.7 6.4 Page 39 of 41 Part #: HSEC8-160-01-L-RA 0.3 3.5 -0.2 2.7 1.8 2.4 1.3 0.0 0.1 0.4 0.5 1.9 2.9 -0.4 2.3 1.5 3.5 -0.5 -0.1 -1.3 0.2 -0.7 -0.6 -3.3 2.3 3.0 0.4 0.1 0.1 -0.3 -0.2 -1.1 0.3 -0.4 -0.3 0.5 0.1 0.0 -0.1 -0.3 -0.4 -0.1 -0.5 -3.1 1.5 0.5 -0.2 -0.2 2.1 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 8.4 7.7 8.0 8.2 8.2 8.1 7.9 8.3 8.1 8.1 8.4 8.3 8.7 8.5 6.6 6.6 6.2 6.6 6.9 7.5 Page 40 of 41 Part #: HSEC8-160-01-L-RA 0.9 2.7 2.2 2.1 3.0 1.5 -0.1 2.8 2.1 0.9 0.7 1.1 1.3 0.5 1.5 1.3 1.2 0.5 0.5 -0.3 Tracking Code: TC0928--2600_Report_Rev_2 Part description: HSEC8 Part #: HSEC8-160-01-L-RA EQUIPMENT AND CALIBRATION SCHEDULES Equipment #: HZ-MO-03 Description: Micro-ohmmeter Manufacturer: Keithley Model: 580 Serial #: 297288 Accuracy: Last Cal: 2009-8-07, Next Cal: 2010-8-06 Equipment #: HZ-TCT-01 Description: Normal force analyzer Manufacturer: Mecmesin Multitester Model: Mecmesin Multitester 2.5-i Serial #: 08-1049-04 Accuracy: Last Cal: 2010-4-28, Next Cal: 2011-4-27 Equipment #: HZ-OV-01 Description: Oven Manufacturer: Huida Model: CS101-1E Serial #: CS101-1E-B Accuracy: Last Cal: 2009-12-15, Next Cal: 2010-12-14 Equipment #: HZ-THC-01 Description: Humidity transmitter Manufacturer: Thermtron Model: HMM30C Serial #: D0240037 Accuracy: Last Cal: 2010-6-4, Next Cal: 2011-6-3 Equipment #: HZ-OGP-01 Description: Video measurement system Manufacturer: OGP Model: SMARTSCOPE FLASH 200 Serial #: SVW2003632 Accuracy: Last Cal: 2009-6-11, Next Cal: 2010-6-10 Page 41 of 41