Project Number: Design Qualification Test Report Requested by: Steven Xu Tracking Code: 173210_Report_Rev_1 Date: 3/6/2012 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Lot #: N/A Product Rev: 0 Tech: Kason He Part description: LSHM-RH\LSHM-DH Test Start: 12/5/2011 Eng: Vico Zhao Qty to test: 80 Test Completed: 1/3/2012 DESIGN QUALIFICATION TEST REPORT LSHM-RH\LSHM-DH LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Page 1 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH CERTIFICATION All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST) traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable. All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be reproduced without prior written approval of Samtec. SCOPE To perform the following tests: Design qualification test. Please see test plan. APPLICABLE DOCUMENTS Standards: EIA Publication 364 TEST SAMPLES AND PREPARATION 1) All materials were manufactured in accordance with the applicable product specification. 2) All test samples were identified and encoded to maintain traceability throughout the test sequences. 3) After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001. 4) Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used. 5) The automated procedure is used with aqueous compatible soldering materials. 6) Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary. 7) Any additional preparation will be noted in the individual test sequences. 8) Solder Information: Lead Free 9) Re-Flow Time/Temp: See accompanying profile. 10) Samtec Test PCBs used: PCB-103391-TST\PCB-103397-TST Page 2 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH TYPICAL OVEN PROFILE (Soldering Parts to Test Boards) Page 3 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Gas Tight TEST GROUP A1 STEP 01 192 Points LLCR-1 02 03 Gas Tight LLCR-2 Gas Tight = EIA-364-36A LLCR = EI A-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 i n 4 wir e dry circuit m ode Norm al Force TEST GROUP A1 GROUP A2 01 Individual Contacts (8-10 m in) Contact Gaps Individual Contacts (8-10 m in) Contact Gaps 02 Setup Approved Thermal Aging (Mated and Undisturbed) 03 Normal Force (in the body and soldered on PCB unless otherwise specified) Contact Gaps STEP 04 Setup Approved 05 Normal Force (in the body and soldered on PCB unless otherwise specified) Thermal Aging = EIA-364-17, Test Condition 4 (105°C) Time Condition 'B' (250 Hours) Normal Force = EIA-364-04 (Perpendicular) Displacement Force = 12.7 mm/min ± 6 mm/min Spec is 50 N @ 1 mm displacement Contact Gaps / Height - No standard method. Usually measured optically Gaps to be taken on a minimum of 20% of each part tested Page 4 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Continued Thermal Aging TEST GROUP A1 STEP 8 Boards Thermal Aging (Mated) 01 Contact Gaps Forces - Mating / Unmating 02 03 LLCR-1 04 Thermal Aging (Mated and Undisturbed) 05 LLCR-2 06 Forces - Mating / Unmating 07 Contact Gaps Thermal Aging = EIA-364-17, Test Condition 4 (105°C) Time Condition 'B' (250 Hours) Mating / Unmating Forces = EIA-364-13 Contact Gaps / Height - No standard method. Usually measured optically. Gaps to be taken on a minimum of 20% of each part tested LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Page 5 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Continued Durability/Mating/Unmating/Gaps TEST GROUP B1 GROUP B2 GROUP B3 GROUP B4 STEP 8 Boards (50 position) 8 Boards (40 position) 8 Boards (30 position) 8 Boards (20 position) Contact Gaps LLCR-1 Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 01 02 03 04 05 06 07 08 09 10 25 Cycles (50 Total) 25 Cycles (75 Total) 25 Cycles (75 Total) 25 Cycles (75 Total) Forces - Mating / Unmating 25 Cycles (75 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 11 25 Cycles (100 Total) Forces - Mating / Unmating 12 13 Clean w/Compressed Air Contact Gaps 14 LLCR-2 15 Thermal Shock (Mated and Undisturbed) 16 LLCR-3 17 Cyclic Humidity (Mated and Undisturbed) 18 LLCR-4 19 Forces - Mating / Unmating Thermal Shock = EIA-364-32, Table II, Test Condition I: -55oC to +85 oC 1/2 hour dwell, 100 cycles Humidity = EIA-364-31, Test Condition B (240 Hours) and Method III (+25°C to +65°C @ 90% RH to 98% RH) ambient pre-condition and delete steps 7a and 7b Mating / Unmating Forces = EIA-364-13 Contact Gaps / Height - No standard method. Usually measured optically. Gaps to be taken on a minimum of 20% of each part tested LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Page 6 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Continued Durability/Mating/Unmating/Gaps TEST GROUP B1 GROUP B2 GROUP B3 GROUP B4 STEP 8 Boards (50 position) 8 Boards (40 position) 8 Boards (30 position) 8 Boards (20 position) Contact Gaps LLCR-1 Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 25 Cycles Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 01 02 03 04 05 06 07 08 09 10 25 Cycles (50 Total) 25 Cycles (75 Total) 25 Cycles (75 Total) 25 Cycles (75 Total) Forces - Mating / Unmating 25 Cycles (75 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 11 25 Cycles (100 Total) Forces - Mating / Unmating 12 13 Clean w/Compressed Air Contact Gaps 14 LLCR-2 15 Thermal Shock (Mated and Undisturbed) 16 LLCR-3 17 Cyclic Humidity (Mated and Undisturbed) 18 LLCR-4 19 Forces - Mating / Unmating Thermal Shock = EIA-364-32, Table II, Test Condition I: -55oC to +85 oC 1/2 hour dwell, 100 cycles Humidity = EIA-364-31, Test Condition B (240 Hours) and Method III (+25°C to +65°C @ 90% RH to 98% RH) ambient pre-condition and delete steps 7a and 7b Mating / Unmating Forces = EIA-364-13 Contact Gaps / Height - No standard method. Usually measured optically. Gaps to be taken on a minimum of 20% of each part tested LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Page 7 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Continued IR & DWV TEST GROUP A1 GROUP A2 GROUP A3 GROUP B1 STEP 2 Mated Sets 2 Unm ated of Part # Being Tested 2 Unmated of Mating Part # 2 Mated Sets Break Down Pin-to-Pin Break Down Pin-to-Pin Break Down Pin-to-Pin Pin-to-Pin DW V/Break Down Voltage DWV/Break Down Voltage DW V/Break Down Voltage IR & DW V at test voltage (on both mated sets and on each connector unmated) 01 02 Thermal Shock (Mated and Undisturbed) 03 IR & DW V at test voltage (on both mated sets and on each connector unmated) 04 Cyclic Humidity (Mated and Undisturbed) 05 IR & DW V at test voltage (on both mated sets and on each connector unmated) DWV on Group B1 to be performed at Test Voltage DWV test voltage is equal to 75% of the lowest break down voltage from Groups A1, A2 or A3 Thermal Shock = EIA-364-32, Table II, Test Condition I: -55oC to +85 oC 1/2 hour dwell, 100 cycles Humidity = EIA-364-31, Test Condition B (240 Hours) and Method III (+25°C to +65°C @ 90% RH to 98% RH) ambient pre-condition and delete steps 7a and 7b IR = EIA-364-21 DWV = EIA-364-20, Test Condition 1 Current Carrying Capacity - Double Row TEST STEP GROUP B1 3 Mated Assemblies 2 Contacts Powered GROUP B2 3 Mated Assemblies 4 Contacts Powered GROUP B3 3 Mated Assemblies 6 Contacts Powered GROU P B4 3 Mated Assemblies 8 Contacts Powered GROUP B5 3 Mated Assem blies All Contacts Powered 01 CCC CCC CCC CCC CCC (TIN PLATING) - Tabulate calculated current at RT, 65°C, 75°C and 95°C after derating 20% and based on 105°C (GOLD PLATING) - Tabulate calculated current at RT, 85°C, 95°C and 115°C after derating 20% and based on 125°C CCC, Temp rise = EIA-364-70 Page 8 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH FLOWCHARTS Continued Mechanical Shock / Vibration / LLCR TEST STEP 01 02 03 04 GROUP A1 192 Points LLCR-1 Shock Vibration LLCR-2 Mechani cal Shock = EI A 364-27 Half Sine, 100 g's, 6 mi lli Seconds (Condition "C") each axis Vibration = EIA 364-28, Random Vibration 7.56 g RMS, Condi ti on VB --- 2 hours/axis LLCR = EI A-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 i n 4 wir e dry circuit m ode Shock / Vibration / nanoSecond Event Detection TEST STEP GROUP A1 60 Points 01 Event Detection, Shock 02 Event Detection, Vibration Mechanical Shock = EIA 364-27 Half Sine, 100 g's, 6 milliSeconds (Condition "C") each axis Vibration = EIA 364-28, Random Vibration 7.56 g RMS, Condition VB --- 2 hours/axis Event detection requir ement dur ing Shock / Vibration is 50 nanoseconds m inimum Page 9 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. THERMAL SHOCK: 1) 2) 3) 4) 5) 6) EIA-364-32, Thermal Shock (Temperature Cycling) Test Procedure for Electrical Connectors. Test Condition 1: -55°C to +85°C Test Time: ½ hour dwell at each temperature extreme Number of Cycles: 100 All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. THERMAL: 1) 2) 3) 4) 5) EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors. Test Condition 4 at 105° C. Test Time Condition B for 250 hours. All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. HUMIDITY: 1) 2) 3) 4) 5) Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors. Test Condition B, 240 Hours. Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b. All samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. MECHANICAL SHOCK (Specified Pulse): 1) 2) 3) 4) 5) 6) 7) Reference document: EIA-364-27, Mechanical Shock Test Procedure for Electrical Connectors Test Condition C Peak Value: 100 G Duration: 6 Milliseconds Wave Form: Half Sine Velocity: 12.3 ft/s Number of Shocks: 3 Shocks / Direction, 3 Axis (18 Total) VIBRATION: 1) 2) 3) 4) 5) 6) Reference document: EIA-364-28, Vibration Test Procedure for Electrical Connectors Test Condition V, Letter B Power Spectral Density: 0.04 G² / Hz G ‘RMS’: 7.56 Frequency: 50 to 2000 Hz Duration: 2.0 Hours per axis (3 axis total) NANOSECOND-EVENT DETECTION: 1) Reference document: EIA-364-87, Nanosecond-Event Detection for Electrical Connectors 2) Prior to test, the samples were characterized to assure the low nanosecond event being monitored will trigger the detector. 3) After characterization it was determined the test samples could be monitored for 50 nanosecond events Page 10 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH ATTRIBUTE DEFINITIONS Continued The following is a brief, simplified description of attributes. TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) EIA-364-70, Temperature Rise versus Current Test Procedure for Electrical Connectors and Sockets. 2 2) When current passes through a contact, the temperature of the contact increases as a result of I R (resistive) heating. 3) The number of contacts being investigated plays a significant part in power dissipation and therefore temperature rise. 4) The size of the temperature probe can affect the measured temperature. 5) Copper traces on PC boards will contribute to temperature rise: a. Self heating (resistive) b. Reduction in heat sink capacity affecting the heated contacts 6) A de-rating curve, usually 20%, is calculated. 7) Calculated de-rated currents at three temperature points are reported: a. Ambient о b. 80 C о c. 95 C о d. 115 C 8) Typically, neighboring contacts (in close proximity to maximize heat build up) are energized. 9) The thermocouple (or temperature measuring probe) will be positioned at a location to sense the maximum temperature in the vicinity of the heat generation area. 10) A computer program, TR 803.exe, ensures accurate stability for data acquisition. 11) Hook-up wire cross section is larger than the cross section of any connector leads/PC board traces, jumpers, etc. 12) Hook-up wire length is longer than the minimum specified in the referencing standard. CONTACT GAPS: 1) Gaps above the surrounding plastic surface were measured before and after stressing the contacts (e.g. thermal aging, mechanical cycling, etc.). 2) Typically, all contacts on the connector are measured. MATING/UNMATING: 1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors. 2) The full insertion position was to within 0.003” to 0.004” of the plug bottoming out in the receptacle to prevent damage to the system under test. 3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling. Page 11 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH ATTRIBUTE DEFINITIONS Continued The following is a brief, simplified description of attributes. NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING): 1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors. 2) The contacts shall be tested in the connector housing. 3) If necessary, a “window” shall be made in the connector body to allow a probe to engage and deflect the contact at the same attitude and distance (plus 0.05 mm [0.002”]) as would occur in actual use. 4) The connector housing shall be placed in a holding fixture that does not interfere with or otherwise influence the contact force or deflection. 5) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2, computer controlled test stand with a deflection measurement system accuracy of 5.0 µm (0.0002”). 6) The nominal deflection rate shall be 5 mm (0.2”)/minute. 7) Unless otherwise noted a minimum of five contacts shall be tested. 8) The force/deflection characteristic to load and unload each contact shall be repeated five times. 9) The system shall utilize the TC2 software in order to acquire and record the test data. 10) The permanent set of each contact shall be measured within the TC2 software. 11) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis and a print out will be stored with the Tracking Code paperwork. Page 12 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH ATTRIBUTE DEFINITIONS Continued The following is a brief, simplified description of attributes. INSULATION RESISTANCE (IR): To determine the resistance of insulation materials to leakage of current through or on the surface of these materials when a DC potential is applied. 1) PROCEDURE: a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Electrification Time 2.0 minutes iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances. 2) MEASUREMENTS: 3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000 megohms. DIELECTRIC WITHSTANDING VOLTAGE (DWV): To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of environmental stresses so not to influence the readings from arcing that occurs during the measurement process. 1) PROCEDURE: a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Barometric Test Condition 1 iii. Rate of Application 500 V/Sec iv. Test Voltage (VAC) until breakdown occurs 2) MEASUREMENTS/CALCULATIONS a. The breakdown voltage shall be measured and recorded. b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage. c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage). LLCR: 1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. 2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition. 3) The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure Page 13 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH ATTRIBUTE DEFINITIONS Continued The following is a brief, simplified description of attributes. GAS TIGHT: 1) 2) 3) 4) To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh vapors which might lead to oxide formation that may degrade the electrical performance of the contact system. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms:--------------------------- Stable b. +5.1 to +10.0 mOhms: -------------------- Minor c. +10.1 to +15.0 mOhms: ------------------ Acceptable d. +15.1 to +50.0 mOhms: ------------------ Marginal e. +50.1 to +2000 mOhms:------------------ Unstable f. >+2000 mOhms: --------------------------- Open Failure Procedure: a. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics for Electrical Connectors, Sockets and/or Contact Systems. b. Test Conditions: i. Class II--- Mated pairs of contacts assembled to their plastic housings. ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1. iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are added. v. Exposure time, 55 to 65 minutes. vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the surface of the acid than 3 inches. vii. The samples shall be dried after exposure for a minimum of 1 hour. о viii. Drying temperature 50 C ix. The final LLCR shall be conducted within 1 hour after drying. Page 14 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Temperature Rise, CCC at a 20% de-rating CCC for a CCC for a CCC for a CCC for a CCC for a 30°C Temperature Rise -----------------------1.9A per contact 30°C Temperature Rise -----------------------1.4A per contact 30°C Temperature Rise -----------------------1.2A per contact 30°C Temperature Rise -----------------------1.0A per contact 30°C Temperature Rise -----------------------0.4A per contact Contact Gaps Normal Force Group Group A1 Initial o Min-------------------------------------------------- 0.0237 in o Max ------------------------------------------------- 0.0267 in Group A2 Initial o Min-------------------------------------------------- 0.0243 in o Max ------------------------------------------------- 0.0264 in Thermal o Min-------------------------------------------------- 0.0275 in o Max ------------------------------------------------- 0.0290 in Thermal Aging Group Initial o Min-------------------------------------------------- 0.0238 in o Max ------------------------------------------------- 0.0273 in Thermal o Min-------------------------------------------------- 0.0269 in o Max ------------------------------------------------- 0.0294 in Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N Initial o Min-------------------------------------------------- 0.0236 in o Max ------------------------------------------------- 0.0271 in After 100 Cycles o Min-------------------------------------------------- 0.0254 in o Max ------------------------------------------------- 0.0289 in LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N Initial o Min-------------------------------------------------- 0.0215 in o Max ------------------------------------------------- 0.0267 in After 100 Cycles o Min-------------------------------------------------- 0.0224 in o Max ------------------------------------------------- 0.0259 in Page 15 of 50 with 2 adjacent contacts powered with 4 adjacent contacts powered with 6 adjacent contacts powered with 8 adjacent contacts powered with all adjacent contacts powered Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating – Unmating Forces Thermal Aging Group Initial o Mating Min --------------------------------------12.67 Lbs Max--------------------------------------15.16 Lbs o Unmating Min --------------------------------------16.13 Lbs Max--------------------------------------18.40 Lbs Thermal o Mating Min --------------------------------------- 7.61 Lbs Max--------------------------------------10.77 Lbs o Unmating Min --------------------------------------10.67 Lbs Max--------------------------------------12.72 Lbs Page 16 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating – Unmating Forces Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N Initial o Mating Min --------------------------------------10.63 Lbs Max--------------------------------------14.27 Lbs o Unmating Min --------------------------------------14.10 Lbs Max--------------------------------------16.78 Lbs After 25 Cycles o Mating Min --------------------------------------11.21 Lbs Max--------------------------------------13.46 Lbs o Unmating Min --------------------------------------14.07 Lbs Max--------------------------------------17.01 Lbs After 50 Cycles o Mating Min --------------------------------------12.66 Lbs Max--------------------------------------14.74 Lbs o Unmating Min --------------------------------------14.67 Lbs Max--------------------------------------18.21 Lbs After 75 Cycles o Mating Min --------------------------------------13.70 Lbs Max--------------------------------------16.01 Lbs o Unmating Min --------------------------------------13.28 Lbs Max--------------------------------------18.71 Lbs After 100 Cycles o Mating Min --------------------------------------14.49 Lbs Max--------------------------------------16.23 Lbs o Unmating Min --------------------------------------13.83 Lbs Max--------------------------------------18.48 Lbs Humidity o Mating Min --------------------------------------- 8.55 Lbs Max--------------------------------------10.82 Lbs o Unmating Min --------------------------------------- 9.96 Lbs Max--------------------------------------13.33 Lbs Page 17 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating – Unmating Forces Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N Initial o Mating Min --------------------------------------11.30 Lbs Max--------------------------------------14.65 Lbs o Unmating Min --------------------------------------13.10 Lbs Max--------------------------------------18.50 Lbs After 25 Cycles o Mating Min --------------------------------------12.24 Lbs Max--------------------------------------13.80 Lbs o Unmating Min --------------------------------------14.80 Lbs Max--------------------------------------17.23 Lbs After 50 Cycles o Mating Min --------------------------------------12.74 Lbs Max--------------------------------------14.96 Lbs o Unmating Min --------------------------------------15.33 Lbs Max--------------------------------------17.80 Lbs After 75 Cycles o Mating Min --------------------------------------12.95 Lbs Max--------------------------------------16.01 Lbs o Unmating Min --------------------------------------15.45 Lbs Max--------------------------------------18.04 Lbs After 100 Cycles o Mating Min --------------------------------------13.72 Lbs Max--------------------------------------16.25 Lbs o Unmating Min --------------------------------------15.83 Lbs Max--------------------------------------18.36 Lbs Humidity o Mating Min --------------------------------------- 7.90 Lbs Max--------------------------------------10.61 Lbs o Unmating Min --------------------------------------10.64 Lbs Max--------------------------------------12.79 Lbs Page 18 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-140-01-F-RH-A-N\ LSHM-140-01-F-DH-A-N Initial o Mating Min --------------------------------------- 9.77 Lbs Max--------------------------------------12.04 Lbs o Unmating Min --------------------------------------10.76 Lbs Max--------------------------------------13.38 Lbs After 25 Cycles o Mating Min --------------------------------------- 9.94 Lbs Max--------------------------------------12.54 Lbs o Unmating Min --------------------------------------10.35 Lbs Max--------------------------------------13.85 Lbs After 50 Cycles o Mating Min --------------------------------------10.48 Lbs Max--------------------------------------13.22 Lbs o Unmating Min --------------------------------------10.86 Lbs Max--------------------------------------14.85 Lbs After 75 Cycles o Mating Min --------------------------------------10.59 Lbs Max--------------------------------------14.17 Lbs o Unmating Min --------------------------------------10.99 Lbs Max--------------------------------------15.51 Lbs After 100 Cycles o Mating Min --------------------------------------11.21 Lbs Max--------------------------------------15.19 Lbs o Unmating Min --------------------------------------11.50 Lbs Max--------------------------------------15.93 Lbs Page 19 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-130-01-F-RH-A-N\ LSHM-130-01-F-DH-A-N Initial o Mating Min --------------------------------------- 9.31 Lbs Max--------------------------------------10.40 Lbs o Unmating Min --------------------------------------11.18 Lbs Max--------------------------------------12.52 Lbs After 25 Cycles o Mating Min --------------------------------------- 9.39 Lbs Max--------------------------------------10.85 Lbs o Unmating Min --------------------------------------10.87 Lbs Max--------------------------------------12.74 Lbs After 50 Cycles o Mating Min --------------------------------------- 9.83 Lbs Max--------------------------------------11.22 Lbs o Unmating Min --------------------------------------11.22 Lbs Max--------------------------------------12.98 Lbs After 75 Cycles o Mating Min --------------------------------------10.37 Lbs Max--------------------------------------11.83 Lbs o Unmating Min --------------------------------------11.59 Lbs Max--------------------------------------13.52 Lbs After 100 Cycles o Mating Min --------------------------------------10.60 Lbs Max--------------------------------------12.15 Lbs o Unmating Min --------------------------------------12.03 Lbs Max--------------------------------------14.01 Lbs Page 20 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-120-01-F-RH-A-N\ LSHM-120-01-F-DH-A-N Initial o Mating Min --------------------------------------- 4.33 Lbs Max--------------------------------------- 5.57 Lbs o Unmating Min --------------------------------------- 5.46 Lbs Max--------------------------------------- 6.96 Lbs After 25 Cycles o Mating Min --------------------------------------- 4.85 Lbs Max--------------------------------------- 5.91 Lbs o Unmating Min --------------------------------------- 5.73 Lbs Max--------------------------------------- 7.24 Lbs After 50 Cycles o Mating Min --------------------------------------- 5.22 Lbs Max--------------------------------------- 6.35 Lbs o Unmating Min --------------------------------------- 6.14 Lbs Max--------------------------------------- 7.68 Lbs After 75 Cycles o Mating Min --------------------------------------- 5.59 Lbs Max--------------------------------------- 7.44 Lbs o Unmating Min --------------------------------------- 6.38 Lbs Max--------------------------------------- 7.93 Lbs After 100 Cycles o Mating Min --------------------------------------- 5.77 Lbs Max--------------------------------------- 7.94 Lbs o Unmating Min --------------------------------------- 6.74 Lbs Max--------------------------------------- 8.07 Lbs Page 21 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-140-01-F-RH-A-N\ LSHM-140-01-F-DV-A-N Initial o Mating Min --------------------------------------- 9.10 Lbs Max--------------------------------------10.75 Lbs o Unmating Min --------------------------------------11.43 Lbs Max--------------------------------------12.87 Lbs After 25 Cycles o Mating Min ------------------------------------- 10.72 Lbs Max--------------------------------------11.79 Lbs o Unmating Min --------------------------------------13.28 Lbs Max--------------------------------------14.28 Lbs After 50 Cycles o Mating Min --------------------------------------11.56 Lbs Max--------------------------------------12.98 Lbs o Unmating Min --------------------------------------13.86 Lbs Max--------------------------------------15.19 Lbs After 75 Cycles o Mating Min --------------------------------------12.61 Lbs Max--------------------------------------14.30 Lbs o Unmating Min ------------------------------------- 14.77 Lbs Max--------------------------------------15.96 Lbs After 100 Cycles o Mating Min --------------------------------------13.25 Lbs Max--------------------------------------15.17 Lbs o Unmating Min --------------------------------------15.26 Lbs Max--------------------------------------16.93 Lbs Page 22 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-130-01-F-RH-A-N\ LSHM-130-01-F-DV-A-N Initial o Mating Min --------------------------------------- 8.29 Lbs Max--------------------------------------- 9.33 Lbs o Unmating Min --------------------------------------- 9.77 Lbs Max--------------------------------------11.08 Lbs After 25 Cycles o Mating Min --------------------------------------- 7.80 Lbs Max--------------------------------------- 8.92 Lbs o Unmating Min --------------------------------------- 8.85 Lbs Max--------------------------------------10.92 Lbs After 50 Cycles o Mating Min --------------------------------------- 8.12 Lbs Max--------------------------------------- 9.24 Lbs o Unmating Min --------------------------------------10.05 Lbs Max--------------------------------------11.25 Lbs After 75 Cycles o Mating Min --------------------------------------- 8.41 Lbs Max--------------------------------------- 9.51 Lbs o Unmating Min --------------------------------------10.27 Lbs Max--------------------------------------11.39 Lbs After 100 Cycles o Mating Min --------------------------------------- 8.79 Lbs Max--------------------------------------10.07 Lbs o Unmating Min --------------------------------------10.58 Lbs Max--------------------------------------11.77 Lbs Page 23 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Mating\Unmating Basic LSHM-120-01-F-RH-A-N\ LSHM-120-01-F-DV-A-N Initial o Mating Min --------------------------------------- 5.13 Lbs Max--------------------------------------- 6.08 Lbs o Unmating Min --------------------------------------- 5.82 Lbs Max--------------------------------------- 6.84 Lbs After 25 Cycles o Mating Min --------------------------------------- 5.47 Lbs Max--------------------------------------- 6.35 Lbs o Unmating Min --------------------------------------- 6.17 Lbs Max--------------------------------------- 7.17 Lbs After 50 Cycles o Mating Min --------------------------------------- 5.92 Lbs Max--------------------------------------- 6.75 Lbs o Unmating Min --------------------------------------- 6.71 Lbs Max--------------------------------------- 9.84 Lbs After 75 Cycles o Mating Min --------------------------------------- 6.24 Lbs Max--------------------------------------- 7.02 Lbs o Unmating Min --------------------------------------- 7.02 Lbs Max--------------------------------------- 8.04 Lbs After 100 Cycles o Mating Min --------------------------------------- 6.84 Lbs Max--------------------------------------- 7.85 Lbs o Unmating Min --------------------------------------- 7.77 Lbs Max--------------------------------------- 8.89 Lbs Normal Force at 0.210 mm deflection Initial o Min-------------------------------------------------93.60 gf o Max ------------------------------------------------98.00 gf Thermal o Min-------------------------------------------------93.50 gf o Max ---------------------------------------------- 100.30 gf o Page 24 of 50 Set ----- 0.0060 mm Set ----- 0.0110 mm Set------ 0.0050 mm Set------ 0.0080 mm Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued Insulation Resistance minimums, IR Initial o Mated ------------------------------------------------10000Meg Ω ------------------------- Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass Thermal o Mated ------------------------------------------------10000Meg Ω ------------------------ Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass Humidity o Mated ------------------------------------------------- 8977Meg Ω ------------------------ Pass o Unmated --------------------------------------------10000Meg Ω ------------------------ Pass Dielectric Withstanding Voltage minimums, DWV Minimums o Breakdown Voltage ----------------------------------625VAC o Test Voltage -------------------------------------------496VAC o Working Voltage ------------------------------------ 156VAC Initial DWV --------------------------------------------------Passed Thermal DWV-----------------------------------------------Passed Humidity DWV----------------------------------------------Passed LLCR Gas Tight (184 LLCR test points) Initial --------------------------------------------------------------- 32.28 mOhms Max Gas-Tight o <= +5.0 mOhms ----------------------------------- 184 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0Points -------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure LLCR Thermal Aging (184 LLCR test points) Initial --------------------------------------------------------------- 31.76 mOhms Max Thermal o <= +5.0 mOhms ----------------------------------- 184 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Page 25 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued LLCR Durability (184 LLCR test points) LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N Initial --------------------------------------------------------------- 31.91 mOhms Max Durability, 100 Cycles o <= +5.0 mOhms ----------------------------------- 175 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------9 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Thermal o <= +5.0 mOhms ----------------------------------- 162 Points ------------------------- Stable o +5.1 to +10.0 mOhms --------------------------------- 22 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Humidity o <= +5.0 mOhms ----------------------------------- 173 Points ------------------------- Stable o +5.1 to +10.0 mOhms --------------------------------- 11 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure LLCR Durability (192 LLCR test points) LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N Initial --------------------------------------------------------------- 31.06mOhms Max Durability, 100 Cycles o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Thermal o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Humidity o <= +5.0 mOhms ----------------------------------- 190 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------2 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Page 26 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH RESULTS Continued LLCR Mechanical Shock & Random Vibration (184 LLCR test points) Initial --------------------------------------------------------------- 32.85mOhms Max Shock & Vibration o <= +5.0 mOhms ----------------------------------- 184 Points ------------------------- Stable o +5.1 to +10.0 mOhms -----------------------------------0 Points ------------------------- Minor o +10.1 to +15.0 mOhms ---------------------------------0 Points ------------------------- Acceptable o +15.1 to +50.0 mOhms ---------------------------------0 Points ------------------------- Marginal o +50.1 to +2000 mOhms---------------------------------0 Points ------------------------- Unstable o >+2000 mOhms ------------------------------------------0 Points ------------------------- Open Failure Mechanical Shock & Random Vibration: o Shock No Damage ----------------------------------- ---------------------------------- Passed 50 Nanoseconds ------------------------------ ---------------------------------- Passed o Vibration No Damage ----------------------------------- ---------------------------------- Passed 50 Nanoseconds ------------------------------ ---------------------------------- Passed Page 27 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) High quality thermocouples whose temperature slopes track one another were used for temperature monitoring. 2) The thermocouples were placed at a location to sense the maximum temperature generated during testing. 3) Temperature readings recorded are those for which three successive readings, 15 minutes apart, differ less than 1° C (computer controlled data acquisition). 4) Adjacent contacts were powered: a. Linear configuration with 2 adjacent conductors/contacts powered Base Curve Derated 20 % 173210 2(2X1) Contacts in Linear series Part Numbers:LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N RT Peak Amp RT Derated Amp Measured Current 85 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.9 Amps 85 ° C Peak Amp 5.0 85 ° C Derated Amp Room Temp= 22.7 C 95 ° C 95 ° C Peak Amp 4.5 4.4 95 ° C Derated Amp Limit 115 ° C Peak Amp Maximum Current, Amp per Contact 4.0 115 ° C Derated Amp 115 ° C 3.5 3.5 Room Temp 125° C Limit 3.0 2.7 2.5 2.3 2.2 2.0 1.9 1.5 1.3 1.1 1.0 Useful Range 0.5 0.0 20 40 60 80 Ambient Temperature, ° C Page 28 of 50 100 120 140 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued b. Linear configuration with 4 adjacent conductors/contacts powered Base Curve 173210 4(2X2) Contacts in Linear series Part Numbers: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Derated 20 % RT Peak Amp RT Derated Amp Measured Current 85 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.4 Amps 85 ° C Peak Amp 85 ° C Derated Amp Room Temp= 22.2 C 95 ° C 3.5 95 ° C Peak Amp 95 ° C Derated Amp 3.2 Limit 115 ° C Peak Amp Maximum Current, Amp per Contact 3.0 115 ° C Derated Amp 115 ° C Room Temp 2.6 2.5 125° C Limit 2.0 2.0 1.7 1.6 1.5 1.4 1.0 1.0 0.8 Useful Range 0.5 0.0 20 40 60 80 Ambient Temperature, ° C Page 29 of 50 100 120 140 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued c. Linear configuration with 6 adjacent conductors/contacts powered Base Curve 173210 6(2X3) Contacts in Linear series Part Numbers:LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Derated 20 % RT Peak Amp RT Derated Amp Measured Current 85 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.2 Amps 85 ° C Peak Amp 85 ° C Derated Amp Room Temp= 23.0 C 95 ° C 3.0 95 ° C Peak Amp 95 ° C Derated Amp Maximum Current, Amp per Contact 2.8 Limit 115 ° C Peak Amp 2.5 115 ° C Derated Amp 115 ° C Room Temp 2.2 2.0 125° C Limit 1.7 1.5 1.5 1.4 1.2 1.0 0.8 0.7 Useful Range 0.5 0.0 20 40 60 80 Ambient Temperature, ° C Page 30 of 50 100 120 140 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued d. Linear configuration with 8 adjacent conductors/contacts powered Base Curve Derated 20 % 173210 8(2X4) Contacts in Linear series Part Numbers: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N RT Peak Amp RT Derated Amp Measured Current 85 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.0Amps 85 ° C Peak Amp 85 ° C Derated Amp Room Temp= 23.5 C 95 ° C 95 ° C Peak Amp 2.5 95 ° C Derated Amp 2.4 Limit Maximum Current, Amp per Contact 115 ° C Peak Amp 115 ° C Derated Amp 115 ° C 2.0 Room Temp 1.9 125° C Limit 1.5 1.5 1.3 1.2 1.0 1.0 0.7 0.6 0.5 Useful Range 0.0 20 40 60 80 Ambient Temperature, ° C Page 31 of 50 100 120 140 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued e. Linear configuration with all adjacent conductors/contacts powered Base Curve Derated 20 % 173210 100(ALL) Contacts in Series Part Numbers: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N RT Peak Amp RT Derated Amp Measured Current Current Rating per Contact (30 Deg. Rise, 20% Derated) = 0.4 Amps 85 ° C 85 ° C Peak Amp 1.2 85 ° C Derated Amp Room Temp= 24.9 C 95 ° C 95 ° C Peak Amp 95 ° C Derated Amp Limit Maximum Current, Amp per Contact 1.0 1.0 115 ° C Peak Amp 115 ° C Derated Amp 115 ° C Room Temp 0.8 0.8 125° C Limit 0.6 0.6 0.5 0.5 0.4 0.4 0.3 0.2 0.2 Useful Range 0.0 20 40 60 80 Ambient Temperature, ° C Page 32 of 50 100 120 140 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued CONTACT GAPS: Normal Force Group Group A1 Initial Pin Type 1 Signal Nominal 0.0264 Hi Limit 0.0303 Lo Limit 0.0225 Min 0.0237 Max 0.0267 Avg 0.0253 St. Dev. 0.0008 Count Initial 10 Group A2 After Thermal Pin Type 1 Pin Type 1 Signal Signal Nominal 0.0264 Nominal 0.0264 Hi Limit 0.0303 Hi Limit 0.0303 Lo Limit 0.0225 Lo Limit 0.0225 Min 0.0243 Min 0.0275 Max 0.0264 Max 0.029 Avg 0.0255 Avg 0.0281 St. Dev. 0.0008 St. Dev. 0.0005 Count 10 Count 10 Thermal Aging Group Initial After Thermal Pin Type 1 Pin Type 1 Signal Signal Nominal 0.0264 Nominal 0.0264 Hi Limit 0.0303 Hi Limit 0.0303 Lo Limit 0.0225 Lo Limit 0.0225 Min 0.0238 Min 0.0269 Max 0.0273 Max 0.0294 Avg 0.0255 Avg 0.0281 St. Dev. 0.0007 St. Dev. 0.0006 Count 80 Count Page 33 of 50 80 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued CONTACT GAPS: Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N Initial After 100 cycles Pin Type 1 Pin Type 1 Signal Signal Nominal 0.0264 Nominal 0.0264 Hi Limit 0.0303 Hi Limit 0.0303 Lo Limit 0.0225 Lo Limit 0.0225 Min 0.0236 Min 0.0254 Max 0.0271 Max 0.0289 Avg 0.0254 Avg 0.0269 St. Dev. 0.0007 St. Dev. 0.0008 Count 80 Count 80 LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N Initial Pin Type 1 Signal After 100 cycles Pin Type 1 Signal Nominal 0.0264 Nominal 0.0264 Hi Limit 0.0303 Hi Limit 0.0303 Lo Limit 0.0225 Lo Limit 0.0225 Min 0.0215 Min 0.0224 Max 0.0267 Max 0.0259 Avg 0.0242 Avg 0.0242 St. Dev. 0.0017 St. Dev. 0.0009 Count 80 Count Page 34 of 50 80 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Thermal Aging Group After Thermals Initial Mating Minimum Maximum Average St Dev Count Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 56.36 67.43 12.67 15.16 13.97 71.75 81.84 16.13 18.40 16.98 33.85 47.90 7.61 10.77 9.69 47.46 56.58 10.67 12.72 12.00 62.13 4.07 8 75.50 3.40 8 0.92 8 0.76 8 43.09 4.36 8 0.98 8 53.36 3.28 8 0.74 8 Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 47.28 10.63 62.72 14.10 49.86 11.21 62.58 14.07 Maximum 63.47 74.64 69.21 54.30 13.46 12.21 75.66 54.29 16.78 15.56 59.87 Average 14.27 12.21 66.66 17.01 14.99 St Dev 5.08 8 1.14 8 4.50 8 1.01 8 3.28 8 0.74 8 4.17 8 0.94 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 56.31 12.66 65.25 14.67 60.94 13.70 59.07 13.28 Maximum 65.56 59.87 14.74 81.00 71.26 18.21 71.21 64.67 16.01 83.22 72.99 18.71 Average St Dev Count 13.46 0.67 8 3.00 8 5.19 8 16.02 1.17 8 14.54 0.76 8 3.38 8 After 100 Cycles Mating 7.99 8 16.41 1.80 8 After Humidity Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Maximum 64.45 72.19 14.49 16.23 61.52 82.20 13.83 18.48 38.03 48.13 8.55 10.82 44.30 59.29 9.96 13.33 Average 68.13 15.32 74.66 16.79 42.93 9.65 50.92 11.45 St Dev 2.73 8 0.61 8 6.92 8 1.56 8 3.76 8 0.84 8 4.87 8 1.09 8 Minimum Count Page 35 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Mating\Unmating Durability Group LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 50.26 11.30 58.27 13.10 54.44 12.24 65.83 14.80 Maximum 65.16 57.96 13.80 13.03 76.64 70.53 18.50 15.86 61.38 60.69 14.65 13.65 82.29 Average 70.17 17.23 15.78 St Dev 4.71 8 1.06 8 8.25 8 1.86 8 2.42 8 0.54 8 3.86 8 0.87 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 56.67 12.74 68.19 15.33 57.60 12.95 68.72 15.45 Maximum 66.54 14.96 79.17 17.80 71.21 16.01 80.24 18.04 Average 62.38 72.45 14.72 0.92 8 73.95 3.26 8 16.29 0.92 8 65.46 St Dev 14.02 0.73 8 16.63 0.88 8 Count 4.11 8 4.10 8 After 100 Cycles Mating 3.90 8 After Humidity Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 61.03 13.72 70.41 15.83 35.14 7.90 47.33 10.64 Maximum 72.28 16.25 81.67 18.36 47.19 10.61 56.89 12.79 Average 68.04 15.30 75.78 17.04 44.34 9.97 54.47 12.25 St Dev 3.69 8 0.83 8 3.80 8 0.85 8 3.79 8 0.85 8 3.20 8 0.72 8 Count Page 36 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued Mating\Unmating Basic LSHM-140-01-F-RH-A-N\ LSHM-140-01-F-DH-A-N Initial After 25 Cycles Mating Newtons Unmating Force (Lbs) Newtons Force (Lbs) Mating Newtons Unmating Force (Lbs) Newtons Force (Lbs) Minimum 43.46 9.77 47.86 10.76 44.21 9.94 46.04 10.35 Maximum 53.55 59.51 55.51 52.07 12.54 11.71 61.60 48.73 13.38 12.48 55.78 Average 12.04 10.96 57.56 13.85 12.94 St Dev 3.12 8 0.70 8 3.77 8 0.85 8 3.56 8 0.80 8 5.17 8 1.16 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 46.62 10.48 48.31 10.86 47.10 10.59 48.88 10.99 Maximum 58.80 13.22 66.05 14.85 63.03 14.17 68.99 15.51 Average 54.79 13.56 1.27 8 58.25 13.10 1.14 8 63.43 4.04 8 12.32 0.91 8 60.31 St Dev 14.26 1.42 8 Count 5.67 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 49.86 11.21 51.15 11.50 Maximum 67.57 15.19 70.86 15.93 Average 61.14 13.75 65.73 14.78 St Dev 5.25 8 1.18 8 6.19 8 1.39 8 Count Page 37 of 50 5.09 8 6.34 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Mating\Unmating Basic LSHM-130-01-F-RH-A-N\ LSHM-130-01-F-DH-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 41.41 9.31 49.73 11.18 41.77 9.39 48.35 10.87 Maximum 46.26 45.11 10.85 10.14 56.67 52.75 12.52 11.86 48.26 44.17 10.40 9.93 55.69 Average 53.03 12.74 11.92 St Dev 2.04 8 0.46 8 1.61 8 0.36 8 2.49 8 0.56 8 2.46 8 0.55 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 43.72 9.83 49.91 11.22 46.13 10.37 51.55 11.59 Maximum 49.91 11.22 57.74 12.98 52.62 11.83 60.14 13.52 Average 46.84 54.42 10.87 0.45 8 55.75 2.05 8 12.24 0.53 8 48.37 St Dev 10.53 0.46 8 12.53 0.62 8 Count 2.37 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 47.15 10.60 53.51 12.03 Maximum 54.04 12.15 62.32 14.01 Average 49.33 11.09 57.34 12.89 St Dev 2.33 8 0.52 8 2.52 8 0.57 8 Count Page 38 of 50 2.01 8 2.75 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Mating\Unmating Basic LSHM-120-01-F-RH-A-N\ LSHM-120-01-F-DH-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 19.26 4.33 24.29 5.46 21.57 4.85 25.49 5.73 Maximum 24.78 23.41 5.91 5.26 32.20 27.39 6.96 6.16 26.29 21.14 5.57 4.75 30.96 Average 29.23 7.24 6.57 St Dev 1.74 8 0.39 8 2.35 8 0.53 8 1.72 8 0.39 8 2.39 8 0.54 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 23.22 5.22 27.31 6.14 24.86 5.59 28.38 6.38 Maximum 28.24 6.35 34.16 7.68 33.09 7.44 35.27 7.93 Average 25.45 31.02 6.35 0.54 8 32.18 1.61 8 6.97 0.45 8 28.26 St Dev 5.72 0.36 8 7.23 0.44 8 Count 1.99 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 25.66 5.77 29.98 6.74 Maximum 35.32 7.94 35.90 8.07 Average 29.77 6.69 33.16 7.46 St Dev 2.67 8 0.60 8 1.76 8 0.40 8 Count Page 39 of 50 2.41 8 1.97 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued Mating\Unmating Basic LSHM-140-01-F-RH-A-N\ LSHM-140-01-F-DV-A-N Initial After 25 Cycles Mating Newtons Unmating Force (Lbs) Newtons Force (Lbs) Mating Newtons Unmating Force (Lbs) Newtons Force (Lbs) Minimum 40.48 9.10 50.84 11.43 47.68 10.72 59.07 13.28 Maximum 47.82 57.25 53.45 50.70 11.79 11.40 63.52 44.91 12.87 12.02 52.44 Average 10.75 10.10 62.04 14.28 13.95 St Dev 2.90 8 0.65 8 2.21 8 0.50 8 1.58 8 0.36 8 1.57 8 0.35 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 51.42 11.56 61.65 13.86 56.09 12.61 65.70 14.77 Maximum 57.74 12.98 67.57 15.19 63.61 14.30 70.99 15.96 Average 55.70 14.77 0.43 8 59.95 13.48 0.62 8 68.99 1.97 8 12.52 0.44 8 65.71 St Dev 15.51 0.43 8 Count 1.90 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 58.94 13.25 67.88 15.26 Maximum 67.48 15.17 75.30 16.93 Average 63.83 14.35 72.06 16.20 St Dev 3.14 8 0.71 8 2.54 8 0.57 8 Count Page 40 of 50 2.74 8 1.93 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Mating\Unmating Basic LSHM-130-01-F-RH-A-N\ LSHM-130-01-F-DV-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 36.87 8.29 43.46 9.77 34.69 7.80 39.36 8.85 Maximum 41.50 37.49 8.92 8.43 48.57 45.92 11.08 10.32 39.68 38.43 9.33 8.64 49.28 Average 44.84 10.92 10.08 St Dev 1.87 8 0.42 8 2.22 8 0.50 8 1.59 8 0.36 8 3.02 8 0.68 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 36.12 8.12 44.70 10.05 37.41 8.41 45.68 10.27 Maximum 41.10 9.24 50.04 11.25 42.30 9.51 50.66 11.39 Average 39.06 47.07 9.06 0.35 8 48.13 1.68 8 10.58 0.47 8 40.30 St Dev 8.78 0.38 8 10.82 0.40 8 Count 2.10 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 39.10 8.79 47.06 10.58 Maximum 44.79 10.07 52.35 11.77 Average 42.07 9.46 49.51 11.13 St Dev 1.69 8 0.38 8 2.18 8 0.49 8 Count Page 41 of 50 1.55 8 1.78 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued MATING/UNMATING: Mating\Unmating Basic LSHM-120-01-F-RH-A-N\ LSHM-120-01-F-DV-A-N Initial After 25 Cycles Mating Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 22.82 5.13 25.89 5.82 24.33 5.47 27.44 6.17 Maximum 27.04 25.50 6.35 5.73 31.89 27.81 6.84 6.25 28.24 24.19 6.08 5.44 30.42 Average 29.44 7.17 6.62 St Dev 1.41 8 0.32 8 1.31 8 0.29 8 1.30 8 0.29 8 1.32 8 0.30 8 Count After 50 Cycles Mating After 75 Cycles Unmating Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 26.33 5.92 29.85 6.71 27.76 6.24 31.22 7.02 Maximum 30.02 6.75 43.77 9.84 31.22 7.02 35.76 8.04 Average 27.51 32.82 6.57 0.25 8 32.97 1.23 8 7.38 1.05 8 29.23 St Dev 6.19 0.28 8 7.41 0.37 8 Count 4.68 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 30.42 6.84 34.56 7.77 Maximum 34.92 7.85 39.54 8.89 Average 31.47 7.08 36.52 8.21 St Dev 1.51 8 0.34 8 1.55 8 0.35 8 Count Page 42 of 50 1.09 8 1.63 8 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING): 1) Calibrated force gauges are used along with computer controlled positioning equipment. 2) For Normal force 8-10 measurements are taken and the averages reported. Initial Averages Min Max St. Dev Count After Thermals Averages Min Max St. Dev Count Deflections in mm Forces in Grams 0.1000 0.1500 0.2000 0.2100 48.14 71.78 92.28 96.08 46.50 70.00 90.60 93.60 51.00 74.60 94.80 98.00 1.097 1.281 1.119 1.287 12 12 12 12 0.0500 24.97 24.20 25.90 0.507 12 SET 0.0079 0.0060 0.0110 0.0016 12 Deflections in mm Forces in Grams 0.1000 0.1500 0.2000 0.2100 48.39 72.10 94.07 97.28 46.50 70.00 91.90 93.50 50.70 75.50 96.80 100.30 1.197 1.406 1.658 2.067 12 12 12 12 0.0500 25.27 24.20 26.80 0.715 12 SET 0.0057 0.0050 0.0080 0.0011 12 INSULATION RESISTANCE (IR): Pin to Pin Mated Unmated Unmated LSHM-RH/LSHM-DH LSHM-RH LSHM-DH Initial 10000 10000 10000 Thermal 10000 8977 10000 10000 10000 10000 Minimum Humidity DIELECTRIC WITHSTANDING VOLTAGE (DWV): Voltage Rating Summ ary Minimum LSHM-RH/LSHM-DH 625 Break Down Voltage Test Voltage Working Voltage 469 156 Pin to Pin Initial Test Voltage Passed After Thermal Test Voltage After Humidity Test Voltage Passed Passed Page 43 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued LLCR Durability: 1) 2) 3) 4) A total of 184points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms ------------------- Unstable f. >+2000 mOhms:---------------------------- Open Failure LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DH-A-N LLCR Measurement Summaries by Pin Type Date 2011-12-5 2011-12-8 2011-12-14 2011-12-29 Room Temp (Deg C) 22 20 22 20 Rel Humidity (%) 43 58 42 50 Technician Kason He Kason He Kason He kason he mOhm v alues Actual Initial Delta Delta Delta 100 Cycles Therm Shck Humidity Pin Type 1: Row 1 Average St. Dev. Min 29.88 0.68 28.37 1.65 1.76 0.00 2.35 2.79 0.01 1.97 1.74 0.02 Max Summary Count Total Count 31.91 168 168 8.32 168 168 9.63 168 168 8.74 168 168 Pin Type 2: Row 2 Average St. Dev. 24.13 0.56 1.03 0.86 1.92 1.08 1.41 1.01 Min Max Summary Count Total Count 23.21 25.09 16 16 0.07 2.81 16 16 0.18 4.21 16 16 0.04 3.99 16 16 LLCR Delta Count by Category m Ohms 100 Cycles Therm Shck Hum idity Stable Minor Acceptable Marginal Unstable <=5 >5 & <=10 >10 & <=15 >15 & <=50>50 & <=100 175 9 0 0 0 162 173 22 11 0 0 Page 44 of 50 0 0 0 0 Open >1000 0 0 0 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued LLCR Durability: 1) 2) 3) 4) A total of 192 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: -------------------------- Stable b. +5.1 to +10.0 mOhms: -------------------- Minor c. +10.1 to +15.0 mOhms: ------------------ Acceptable d. +15.1 to +50.0 mOhms: ------------------ Marginal e. +50.1 to +2000 mOhms------------------- Unstable f. >+2000 mOhms: --------------------------- Open Failure LSHM-150-01-F-RH-A-N\ LSHM-150-01-F-DV-A-N LLCR Measurement Summaries by Pin Type Date 2011-12-6 Room Temp (Deg C) 22 Rel Humidity (%) 55 Technician Kason He mOhm values Actual Initial Average St. Dev. Min Max Summary Count Total Count 27.16 0.84 25.40 31.06 88 88 Average St. Dev. Min Max Summary Count Total Count 20.74 0.41 19.89 21.54 104 104 2011-12-8 22 58 Kason He Delta 100 Cycles 2011-12-14 22 42 Kason He Delta Therm Shck 2011-12-29 20 52 kason he Delta Humidity Pin Type 1: Row 1 1.02 1.08 0.59 0.65 0.01 0.01 3.47 3.61 88 88 88 88 Pin Type 2: Row 2 0.63 0.66 0.39 0.39 0.02 0.00 1.96 2.60 104 104 104 104 1.36 0.82 0.00 3.18 88 88 1.00 1.18 0.02 5.72 104 104 LLCR Delta Count by Category mOhms 100 Cycles Therm Shck Humidity Stable <=5 192 192 Minor >5 & <=10 0 0 Acceptable >10 & <=15 0 0 Marginal >15 & <=50 0 0 Unstable >50 & <=1000 0 0 Open >1000 0 0 190 2 0 0 0 0 Page 45 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued LLCR Thermal: 1) 2) 3) 4) A total of 184 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: -------------------------- Stable b. +5.1 to +10.0 mOhms:-------------------- Minor c. +10.1 to +15.0 mOhms: ------------------ Acceptable d. +15.1 to +50.0 mOhms: ------------------ Marginal e. +50.1 to +2000 mOhms ------------------ Unstable g. >+2000 mOhms: -------------------------- Open Failure LLCR Measurement Sum maries by Pin Type Date 2011-12-5 2011-12-17 Room Temp (Deg C) 22 23 Rel Humidity (%) 43 33 Kason He Kason He Actual Delta Technician mOhm values Initial Thermal Pin Type 1: Row 1 Average 29.65 0.28 St. Dev. Min 0.63 28.49 0.19 0.00 Max 31.76 0.90 Summary Count 168 168 Total Count 168 168 Pin Type 2: Row 2 Average St. Dev. 24.62 0.31 0.51 0.22 Min 23.37 0.02 Max Summary Count 25.49 16 0.76 16 16 16 Total Count LLCR Delta Count by Category Stable mOhms Thermal <=5 Minor Acceptable Marginal Unstable Open >5 & <=10 >10 & <=15 >15 & <=50>50 & <=1000 >1000 184 0 0 Page 46 of 50 0 0 0 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued GAS TIGHT: 1) 2) 3) 4) A total of 184 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms: ------------------ Unstable f. >+2000 mOhms:---------------------------- Open Failure LLCR Measurement Sum maries by Pin Type Date 2011-12-6 2011-12-8 Room Temp (Deg C) 22 22 Rel Humidity (%) 55 58 Kason He Kason He Actual Delta Technician mOhm values Initial Acid Vapor Pin Type 1: Row 1 Average 29.96 0.45 St. Dev. Min 0.67 28.20 0.38 0.00 Max 32.28 2.25 Summary Count 168 168 Total Count 168 168 Pin Type 2: Row 2 Average St. Dev. 24.74 0.57 0.59 0.30 Min 23.66 0.05 Max Summary Count 25.50 16 1.05 16 16 16 Total Count LLCR Delta Count by Category Stable mOhms Acid Vapor <=5 Minor Acceptable Marginal Unstable Open >5 & <=10 >10 & <=15 >15 & <=50>50 & <=1000 >1000 184 0 0 Page 47 of 50 0 0 0 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH DATA SUMMARIES Continued LLCR Shock & Vibration: 1) 2) 3) 4) A total of 184 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms: --------------------------- Stable b. +5.1 to +10.0 mOhms:--------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms ------------------- Unstable f. >+2000 mOhms:---------------------------- Open Failure LLCR Measurement Sum maries by Pin Type Date Room Temp (Deg C) Rel Humidity (%) Technician 2011-12-22 22 32 Aaron McKim 2012-1-4 23 33 Aaron McKim Actual Delta mOhm values Initial Shock-Vib Pin Type 1: Row 1 Average St. Dev. Min 29.99 0.72 28.39 0.27 0.23 0.00 Max Summary Count 32.85 168 1.11 168 168 168 Total Count Pin Type 2: Row 2 Average 24.49 St. Dev. 0.64 0.34 0.30 Min 23.17 0.01 Max Summary Count Total Count 25.32 16 16 1.09 16 16 LLCR Delta Count by Category Stable mOhms <=5 Shock-Vib Minor Acceptable Marginal Unstable Open >5 & <=10 >10 & <=15 >15 & <=50>50 & <=1000 >1000 184 0 0 0 0 Nanosecond Event Detection: Shock and Vibration Event Detection Summary Contacts tested Test Condition Shock Events Test Condition Vibration Events Total Events 48 C, 100g's, 6ms, Half-Sine 0 V-B, 7.56 rms g 0 0 Page 48 of 50 0 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH EQUIPMENT AND CALIBRATION SCHEDULES Equipment #: HZ-TCT-01 Description: Normal force analyzer Manufacturer: Mecmesin Multitester Model: Mecmesin Multitester 2.5-i Serial #: 08-1049-04 Accuracy: Last Cal: 4/27/2011, Next Cal: 4/26/2012 Equipment #: HZ-OV-01 Description: Oven Manufacturer: Huida Model: CS101-1E Serial #: CS101-1E-B Accuracy: Last Cal: 12/13/2011, Next Cal: 12/12/2012 Equipment #: HZ-THC-01 Description: Humidity transmitter Manufacturer: Thermtron Model: HMM30C Serial #: D0240037 Accuracy: Last Cal: 3/1/2011, Next Cal: 2/28/2012 Equipment #: HZ-OGP-01 Description: Video measurement system Manufacturer: OGP Model: SMARTSCOPE FLASH 200 Serial #: SVW2003632 Accuracy: Last Cal: 6/9/2011, Next Cal: 6/8/2012 Equipment #: HZ-MO-01 Description: Micro-ohmmeter Manufacturer: Keithley Model: 2700 Serial #: 1199807 Accuracy: Last Cal: 4/27/2011, Next Cal: 4/26/2012 Equipment #: HZ-PS-01 Description: Power Supply Manufacturer: Agilent Model: 6031A Serial #: MY41000982 Accuracy: Last Cal: 4/27/2011, Next Cal: 4/26/2012 Page 49 of 50 Tracking Code: 173210_Report_Rev_1 Part #: LSHM-150-01-F-RH-A-N\LSHM-150-01-F-DH-A-N Part description: LSHM-RH\LSHM-DH EQUIPMENT AND CALIBRATION SCHEDULES Continued Equipment #: HZ-HPM-01 Description: NA9636H Manufacturer: Ainuo Model: 6031A Serial #: 089601091 Accuracy: Last Cal: 3/8/2011, Next Cal: 3/7/2012 Equipment #: SVC-01 Description: Shock & Vibration Table Manufacturer: Data Physics Model: LE-DSA-10-20K Serial #: 10037 Accuracy: See Manual … Last Cal: 11/31/2010, Next Cal: 11/31/2011 Equipment #: ACLM-01 Description: Accelerometer Manufacturer: PCB Piezotronics Model: 352C03 Serial #: 115819 Accuracy: See Manual … Last Cal: 07/09/2011, Next Cal: 07/09/2012 Equipment #: ED-03 Description: Event Detector Manufacturer: Analysis Tech Model: 32EHD Serial #: 1100604 Accuracy: See Manual … Last Cal: 06/04/2011, Next Cal: 06/04/2012 Page 50 of 50