«Picture_Description» is depicted

Product Specification
Series: SMB5 50Ω SMB Jack / Plug
SMB5-TH – Jack, Right Angle Orientation, Through-hole
SMB5-CA – Plug, Straight Orientation, Cable Terminated
Other configurations available for:
Right angle cable-to-board applications
Through-hole, panel mount
Termination to various cable types
See www.samtec.com for more information.
Revision: A
Date: May 26, 2014
Page 1
© Samtec, Inc.
Product Specification
Series: SMB5 50Ω SMB Jack / Plug
1.0 SCOPE
1.1 This specification covers performance, testing and quality requirements for Samtec SMB5 Series 50Ω SMB Jack /
Plug. These connectors are available in right angle and panel mount. All information contained in this specification is
for a right angle jack board connector to a straight plug cable assembly unless otherwise noted.
2.0 DETAILED INFORMATION
2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at
http://www.samtec.com/rf/50-ohm/smb.aspx.
3.0 TESTING
3.1
ITEM
Terminal Orientation
Withstanding Voltage
RF174
ST
RF316
RA
ST
1000 DCV 1000 DCV 1000 DCV
RF178
RA
ST
RA
1000 DCV
1000 DCV
1000 DCV
3.2 Electrical:
ITEM
TEST CONDITION
REQUIREMENT
STATUS
Withstanding Voltage
EIA-364-20 (No Flashover,
Sparkover, or Breakdown)
See Section 3.1
Pass
Insulation Resistance
EIA-364-21 (5000 MΩ
minimum)
50,000 MΩ
Pass
Contact Resistance
(LLCR)
EIA-364-23
Δ 15 mΩ maximum
(Samtec defined)/ No damage
Pass
REQUIREMENT
STATUS
3.3 Mechanical:
ITEM
TEST CONDITION
Durability
EIA-364-09C
500 cycles
Pass
Random Vibration
EIA-364-28 Condition V, Letter B
7.56 G 'RMS', 50 to 2000 Hz, 2
hours per axis, 3 axis total , PSD
0.04
Visual Inspection: No Damage
LLCR: Δ 15 mΩ maximum
Event Detection: No interruption >
1.0 microsecond
Pass
Mechanical Shock
EIA-364-27 100 G, 6
milliseconds, half sine, 12.3 ft/s, 3
shocks/direction, 3 axis (18 total
shocks)
Visual Inspection: No Damage
LLCR: Δ 15 mΩ maximum
Event Detection: No interruption >
1.0 microsecond
Pass
Normal Force
EIA-364-04
30 grams minimum for gold
interface
Pass
Mating / Unmating
Force
EIA-364-13
Mating force: 14 lbs maximum
Unmating force: 2 lbs minimum
Pass
Revision: A
Date: May 26, 2014
Page 2
© Samtec, Inc.
Product Specification
Series: SMB5 50Ω SMB Jack / Plug
3.4 Environmental:
ITEM
REQUIREMENT
STATUS
Thermal Shock
EIA-364-32
Thermal Cycles: 100 (30 minute dwell)
Hot Temp: +85°C
Cold Temp: -55°C
Hot/Cold Transition: Immediate
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 360 VAC
IR: >15,000 MΩ
Pass
Thermal Aging
(Temp Life)
EIA-364-17
Test Condition 4 @ 105°C Condition B
for 250 hours
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 360 VAC
IR: >15,000 MΩ
Pass
Cyclic Humidity
EIA-364-31
Test Temp: +25°C to +65°C
Relative Humidity: 90 to 95%
Test Duration: 240 hours
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 360 VAC
IR: >15,000 MΩ
Pass
Gas Tight
EIA-364-36
Gas Exposure: Nitric Acid Vapor
Duration: 60 min.
Drying Temp.: 50°C +/- 3°C
Measurements: Within 1 hour of
Exposure
LLCR: Δ 15 mΩ
Pass
Revision: A
TEST CONDITION
Date: May 26, 2014
Page 3
© Samtec, Inc.
Product Specification
Series: SMB5 50Ω SMB Jack / Plug
4.0 MATED SYSTEM
4.1 Orientations
5.0 HIGH SPEED PERFORMANCE
5.1 Frequency Range:
Cable type
RF174
RF316
RF178
SMB5 Orientation
RA
ST
RA
ST
RA
ST
Frequency Range
DC-4 GHz
DC-4 GHz
DC-4 GHz
DC-4 GHz
DC-4 GHz
DC-4 GHz
5.2 Impedance: 50 ohm
5.3 Rating: Performance up to 4 GHz
Revision: A
Date: May 26, 2014
Page 4
© Samtec, Inc.
Product Specification
Series: SMB5 50Ω SMB Jack / Plug
6.0 APPLICATION INFORMATION
6.1 Minimum Cable Bend Radius: RF174 = 1.00 in [ 25.4]
RF316 = .50 in [12.7]
RF178 = .40 in [10.2]
7.0 ADDITIONAL RESOURCES
7.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at
[email protected]
7.2 For additional information on high speed performance testing, contact our Signal Integrity Group at
[email protected]
7.3 For additional processing information, contact our Interconnect Processing Group at [email protected]
7.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental
Compliance Group at [email protected]
Revision: A
Date: May 26, 2014
Page 5
© Samtec, Inc.