Project Number: Design Qualification Test Report Requested by: Mark Shireman Tracking Code: 112488_Report_Rev_1 Date: 11/9/2011 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Product Rev: 0 Lot #: N/A Tech: Peter Chen Part description: IDSD\TST Test Start: 2/25/2011 Eng: Vico Zhao Qty to test: 45 Test Completed: 3/25/2011 Design Qualification Test Report IDSD\TST IDSD-36-D-06.00-G\TST-136-01-G-D-01 Page 1 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST CERTIFICATION All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST) traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable. All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be reproduced without prior written approval of Samtec. SCOPE To perform the following tests: Design Qualification Test, Please see test plan. APPLICABLE DOCUMENTS Standards: EIA Publication 364 TEST SAMPLES AND PREPARATION 1) 2) 3) 4) 5) All materials were manufactured in accordance with the applicable product specification. All test samples were identified and encoded to maintain traceability throughout the test sequences. After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001. Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used. The automated procedure is used with aqueous compatible soldering materials. 6) Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary. 7) Any additional preparation will be noted in the individual test sequences. 8) Solder Information: Lead free 9) Re-Flow Time/Temp: See accompanying profile. 10) Samtec Test PCBs used: PCB-102989-TST-XX Page 2 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST TYPICAL OVEN PROFILE (Soldering Parts to Test Boards) Page 3 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST FLOWCHARTS Gas Tight TEST STEP GROUP A 01 02 03 LLCR-1 Gas Tight LLCR-2 192 Points Gas Tight = EIA-364 -36A LLCR = EIA-364 -23, LLCR use Keithley 58 0 in the dry circuit mode, 10 mA Max IR & DWV TEST GROU P A1 STEP 2 Mated Sets 01 GROUP A2 2 Unmated of Part # Being Tested GROUP A3 GROUP B1 2 Unmated of Mating Part # 2 Mated Sets Break Down Pin-to-Pin Break Down Pin-to-Pin Break Down Pin-to-Pin Pin-to-Pin DW V/Break Down Voltage DWV/Break Down Voltage DWV/Break Down Voltage IR & DWV at test voltage (on both mated sets and on each connector unmated) 02 Thermal Shock (Mated and Undisturbed) 03 IR & DWV at test voltage (on both mated sets and on each connector unmated) 04 Cyclic Humidity (Mated and Undisturbed) 05 IR & DWV at test voltage (on both mated sets and on each connector unmated) DWV on Group B1 to be performed at Test Voltage DWV test voltage is equal to 75% of the lowest break down voltage from Groups A1, A2 or A3 Thermal Shock = EIA-364-32, Table II, Test Condition I: -55o C to +85o C 1/2 hour dw ell, 100 cycles Hum idity = EIA-364-31, Test Condition B (240 Hours) and Method III (+25°C to +65°C @ 90% RH to 98% RH) ambient pre-condition and delete steps 7a and 7b IR = EIA-364-21 DWV = EIA-364-20, Test Condition 1 Page 4 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST FLOWCHARTS Continued Durability/Mating/Unmating/Gaps TEST GROUPB1 GROUP B 2 GR OUP B3 STEP 8 Boards (Largest position submitted) 8 Boards (Largest position submitted) 8 Boards (Largest position submitted) 01 Contact Gaps Forces - Mating / Unmating Forces - Mating / Unmating 02 LLCR-1 25 Cycles 25 Cycles 03 04 Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 05 25 Cycles Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 25 Cycles (50 Total) Forces - Mating / Unmating 06 25 Cycles (50 Total) 25 Cycles (75 Total) 25 Cycles (75 Total) 07 Forces - Mating / Unmating Forces - Mating / Unmating Forces - Mating / Unmating 08 09 25 Cycles (75 Total) 25 Cycles (100 Total) 25 C ycles (100 Total) Forces - Mating / Unmating 25 Cycles (100 Total) Forces - Mating / Unmating Forces - Mating / Unmating 10 11 Forces - Mating / Unmating 12 13 C lean w/Compressed Air 14 15 Contact Gaps LLCR-2 Thermal Shock (Mated and Undisturbed) 16 LLCR-3 17 Cyclic Humidity (Mated and Undisturbed) 18 LLCR-4 19 Forces - Mating / Unmating Thermal Shock = EIA-364-32, Table II, Test Condition I: -55o C to +85o C 1/2 hour dw ell, 100 cycles Hum idity = EIA-364-31, Test Condition B (240 Hours) and Method III (+25°C to +65°C @ 90% RH to 98% RH) ambient pre-condition and delete steps 7a and 7b Mating / Unm ating Forces = EIA-364-13 Contact Gaps / Height - No standard method. Usually measured optically. LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Page 5 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST FLOWCHARTS Continued Thermal Aging TEST STEP GROUP A1 8 Boards Thermal Aging (Mated) 01 Contact Gaps 02 Forces - Mating / Unmating 03 LLCR-1 04 Thermal Aging (Mated and Undisturbed) 05 LLCR-2 06 Forces - Mating / Unmating 07 Contact Gaps Thermal Aging = EIA-364-17, Test Condition 4 (105°C) Time Condition 'B' (250 Hours) Mating / Unm ating Forces = EIA-364-13 Contact Gaps / Height - No standard method. Usually m easured optically. LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Normal Force TEST 01 GROUP A1 Individual Contacts (8-10 min) Contact Gaps GROUP A2 Individual Contacts (8-10 min) Contact Gaps 02 Setup Approved Thermal Aging (Mated and Undisturbed) 03 Normal Force (in the body and soldered on PCB unless otherwise specified) Contact Gaps STEP 04 Setup Approved 05 Normal Force (in the body and soldered on PCB unless otherwise specified) Thermal Aging = EIA-364-17, Test Condition 4 (105°C) Time Condition 'B' (250 Hours) Normal Force = EIA-364-04 (Perpendicular) Displacement Force = 12.7 mm/m in ± 6 mm /min Spec is 50 N @ 1 mm displacement Contact Gaps / Height - No standard method. Usually m easured optically Page 6 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST FLOWCHARTS Continued Current Carrying Capacity - Double Row TEST STEP 01 TEST STEP 01 GROUP B1 3 Mated Assemblies GROUP B2 3 Mated Assemblies GROUP B3 3 Mated Assemblies 2 Contacts Powered 4 Contacts Powered 6 Contacts Powered CCC GROUP B4 3 Mated Assemblies 8 Contacts Powered CCC CCC GROUP B5 3 Mated Assemblies All Contacts Powered CCC CCC (TIN P LATING) - Tabulate calculated current at RT, 65°C, 75°C and 95°C after derating 20% and based on 105°C (GOLD PLATING) - Tabulate calculated current at RT, 85°C, 95°C and 115°C after derating 20% and based on 125°C CCC, Tem p rise = EIA-364-70 Mechanical Shock / Vibration / LLCR TEST GROUP A1 STEP 192 Points 01 02 LLCR-1 03 Vibration LLCR-2 04 Shock Mechanical Shock = EIA 364-27 Half Sine, 100 g's, 6 milliSeconds (Condition "C") each axis V ibration = EIA 364-28, Random Vibration 7.56 g RMS, Condition VB --- 2 hours/axis LLCR = EIA-364-23, LLCR 20 mV Max, 100 mA Max Use Keithley 580 or 3706 in 4 wire dry circuit mode Page 7 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST FLOWCHARTS Continued Shock / Vibration / nanoSecond Event Detection TEST GROUP A1 STEP 60 Points 01 Event Detection, Shock 02 Event Detection, Vibration Mechanical Shock = EIA 364-27 Half Sine, 100 g' s, 6 milliSeconds (Condition "C") each axis V ibration = EIA 364-28, Random Vibration 7.56 g RMS, Condition VB --- 2 hours/axis E vent detection requirement during Shock / Vibration is 50 nanoseconds minimum Page 8 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. THERMAL SHOCK: 1) 2) 3) 4) 5) 6) EIA-364-32, Thermal Shock (Temperature Cycling) Test Procedure for Electrical Connectors. Test Condition 1: -55°C to +85°C Test Time: ½ hour dwell at each temperature extreme Number of Cycles: 100 All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. THERMAL: 1) 2) 3) 4) 5) EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors. Test Condition 4 at 105° C. Test Time Condition B for 250 hours. All test samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. HUMIDITY: 1) 2) 3) 4) 5) Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors. Test Condition B, 240 Hours. Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b. All samples are pre-conditioned at ambient. All test samples are exposed to environmental stressing in the mated condition. MECHANICAL SHOCK (Specified Pulse): 1) 2) 3) 4) 5) 6) 7) Reference document: EIA-364-27, Mechanical Shock Test Procedure for Electrical Connectors Test Condition C Peak Value: 100 G Duration: 6 Milliseconds Wave Form: Half Sine Velocity: 12.3 ft/s Number of Shocks: 3 Shocks / Direction, 3 Axis (18 Total) VIBRATION: 1) 2) 3) 4) 5) 6) Reference document: EIA-364-28, Vibration Test Procedure for Electrical Connectors Test Condition V, Letter B Power Spectral Density: 0.04 G² / Hz G RMS : 7.56 Frequency: 50 to 2000 Hz Duration: 2.0 Hours per axis (3 axis total) NANOSECOND-EVENT DETECTION: 1) Reference document: EIA-364-87, Nanosecond-Event Detection for Electrical Connectors 2) Prior to test, the samples were characterized to assure the low nanosecond event being monitored will trigger the detector. 3) After characterization it was determined the test samples could be monitored for 50 nanosecond events Page 9 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. CONTACT GAPS: 1) Gaps above the surrounding plastic surface were measured before and after stressing the contacts (e.g. thermal aging, mechanical cycling, etc.). 2) Typically, all contacts on the connector are measured. MATING/UNMATING: 1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors. 2) The full insertion position was to within 0.003 to 0.004 of the plug bottoming out in the receptacle to prevent damage to the system under test. 3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling. NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING): 1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors. 2) The contacts shall be tested in the connector housing. 3) If necessary, a window shall be made in the connector body to allow a probe to engage and deflect the contact at the same attitude and distance (plus 0.05 mm [0.002 ]) as would occur in actual use. 4) The connector housing shall be placed in a holding fixture that does not interfere with or otherwise influence the contact force or deflection. 5) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2, computer controlled test stand with a deflection measurement system accuracy of 5.0 µm (0.0002 ). 6) The nominal deflection rate shall be 5 mm (0.2 )/minute. 7) Unless otherwise noted a minimum of five contacts shall be tested. 8) The force/deflection characteristic to load and unload each contact shall be repeated five times. 9) The system shall utilize the TC2 software in order to acquire and record the test data. 10) The permanent set of each contact shall be measured within the TC2 software. 11) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis and a print out will be stored with the Tracking Code paperwork. INSULATION RESISTANCE (IR): To determine the resistance of insulation materials to leakage of current through or on the surface of these materials when a DC potential is applied. 1) PROCEDURE: a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Electrification Time 2.0 minutes iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances. 2) MEASUREMENTS: 3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000 megohms. Page 10 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. DIELECTRIC WITHSTANDING VOLTAGE (DWV): To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of environmental stresses so not to influence the readings from arcing that occurs during the measurement process. 1) PROCEDURE: a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors. b. Test Conditions: i. Between Adjacent Contacts or Signal-to-Ground ii. Rate of Application 500 V/Sec iii. Test Voltage (VAC) until breakdown occurs 2) MEASUREMENTS/CALCULATIONS a. The breakdown voltage shall be measured and recorded. b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage. c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage).. TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) EIA-364-70, Temperature Rise versus Current Test Procedure for Electrical Connectors and Sockets. 2 2) When current passes through a contact, the temperature of the contact increases as a result of I R (resistive) heating. 3) The number of contacts being investigated plays a significant part in power dissipation and therefore temperature rise. 4) The size of the temperature probe can affect the measured temperature. 5) Copper traces on PC boards will contribute to temperature rise: a. Self heating (resistive) b. Reduction in heat sink capacity affecting the heated contacts 6) A de-rating curve, usually 20%, is calculated. 7) Calculated de-rated currents at three temperature points are reported: a. Ambient b. 80 C c. 95 C d. 115 C 8) Typically, neighboring contacts (in close proximity to maximize heat build up) are energized. 9) The thermocouple (or temperature measuring probe) will be positioned at a location to sense the maximum temperature in the vicinity of the heat generation area. 10) A computer program, TR 803.exe, ensures accurate stability for data acquisition. 11) Hook-up wire cross section is larger than the cross section of any connector leads/PC board traces, jumpers, etc. 12) Hook-up wire length is longer than the minimum specified in the referencing standard. Page 11 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST ATTRIBUTE DEFINITIONS The following is a brief, simplified description of attributes. LLCR: 1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. 2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition. 3) The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms:------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure GAS TIGHT: 8) 9) 10) 11) To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh vapors which might lead to oxide formation that may degrade the electrical performance of the contact system. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms:------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure Procedure: a. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics for Electrical Connectors, Sockets and/or Contact Systems. b. Test Conditions: i. Class II--- Mated pairs of contacts assembled to their plastic housings. ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1. iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are added. v. Exposure time, 55 to 65 minutes. vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the surface of the acid than 3 inches. vii. The samples shall be dried after exposure for a minimum of 1 hour. viii. Drying temperature 50 C ix. The final LLCR shall be conducted within 1 hour after drying. Page 12 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Temperature Rise, CCC at a 20% de-rating CCC for a 30°C Temperature Rise ---------------3.4 A per contact CCC for a 30°C Temperature Rise ---------------2.9 A per contact CCC for a 30°C Temperature Rise ---------------2.4 A per contact CCC for a 30°C Temperature Rise ---------------2.2 A per contact CCC for a 30°C Temperature Rise ---------------1.6 A per contact Contact Gaps Mating&Unmating durability Initial o Min --------------------------------------------------0.0131 Inch o Max--------------------------------------------------0.0186 Inch After 100 Cycles o Min --------------------------------------------------0.0182 Inch o Max--------------------------------------------------0.0239 Inch Thermal aging Initial o Min --------------------------------------------------0.0106 Inch o Max--------------------------------------------------0.0216 Inch After thermal aging o Min --------------------------------------------------0.0174 Inch o Max--------------------------------------------------0.0225 Inch Normal force initial Initial o Min --------------------------------------------------0.0171 Inch o Max--------------------------------------------------0.0199 Inch Normal force after thermal Initial o Min --------------------------------------------------0.0178 Inch o Max--------------------------------------------------0.0201 Inch After thermal aging o Min --------------------------------------------------0.0181 Inch o Max--------------------------------------------------0.0199 Inch Mating /unmating force Mating&Unmating durability (Largest position submitted): Initial o Mating Min ------------------------------------- 20.68 Lbs Max ------------------------------------- 26.86 Lbs o Unmating Min ------------------------------------- 19.16 Lbs Max ------------------------------------- 21.94 Lbs After 25 Cycles o Mating Min ------------------------------------- 20.37 Lbs Max ------------------------------------- 24.94 Lbs o Unmating Min ------------------------------------- 18.87 Lbs Max ------------------------------------- 21.65 Lbs Page 13 of 55 with 2 adjacent contacts powered with 4 adjacent contacts powered with 6 adjacent contacts powered with 8 adjacent contacts powered with all adjacent contacts powered Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Continued After 50 Cycles o Mating Min ------------------------------------- 19.25 Lbs Max ------------------------------------- 23.02 Lbs o Unmating Min ------------------------------------- 18.28 Lbs Max ------------------------------------- 21.39 Lbs After 75 Cycles o Mating Min ------------------------------------- 18.21 Lbs Max ------------------------------------- 22.56 Lbs o Unmating Min ------------------------------------- 18.13 Lbs Max ------------------------------------- 20.79 Lbs After 100 Cycles o Mating Min ------------------------------------- 18.08 Lbs Max ------------------------------------- 21.81 Lbs o Unmating Min ------------------------------------- 17.86 Lbs Max ------------------------------------- 20.40 Lb After Humidity o Mating Min ------------------------------------- 17.79 Lbs Max ------------------------------------- 21.39 Lbs o Unmating Min ------------------------------------- 17.55 Lbs Max ------------------------------------- 20.00 Lbs Mating/Unmating basic (middle position submitted): Initial o Mating Min ------------------------------------- 10.72 Lbs Max ------------------------------------- 12.50 Lbs o Unmating Min ------------------------------------- 10.30 Lbs Max ------------------------------------- 11.36 Lbs After 25 Cycles o Mating Min ------------------------------------- 10.36 Lbs Max ------------------------------------- 11.95 Lbs o Unmating Min ------------------------------------- 10.08 Lbs Max ------------------------------------- 11.25 Lbs After 50 Cycles o Mating Min ---------------------------------------9.81 Lbs Max ------------------------------------- 11.07 Lbs o Unmating Min ------------------------------------- 10.08 Lbs Max ------------------------------------- 10.67 Lbs Page 14 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Continued After 75 Cycles o Mating Min ---------------------------------------9.53 Lbs Max ------------------------------------- 10.76 Lbs o Unmating Min ---------------------------------------9.77 Lbs Max ------------------------------------- 10.28 Lbs After 100 Cycles o Mating Min ---------------------------------------9.26 Lbs Max ------------------------------------- 10.43 Lbs o Unmating Min ---------------------------------------9.64 Lbs Max ------------------------------------- 10.10 Lb Mating/Unmating basic (smallest position submitted): Initial o Mating Min ---------------------------------------2.45Lbs Max ---------------------------------------3.37 Lbs o Unmating Min ---------------------------------------2.14 Lbs Max ---------------------------------------3.46 Lbs After 25 Cycles o Mating Min ---------------------------------------2.12 Lbs Max ---------------------------------------2.95 Lbs o Unmating Min ---------------------------------------1.74 Lbs Max ---------------------------------------2.73 Lbs After 50 Cycles o Mating Min ---------------------------------------2.09 Lbs Max ---------------------------------------2.82 Lbs o Unmating Min ---------------------------------------1.76 Lbs Max ---------------------------------------2.65 Lbs After 75 Cycles o Mating Min ---------------------------------------1.98 Lbs Max ---------------------------------------2.76 Lbs o Unmating Min ---------------------------------------1.76 Lbs Max ---------------------------------------2.67 Lbs After 100 Cycles o Mating Min ---------------------------------------1.87 Lbs Max ---------------------------------------2.58 Lbs o Unmating Min ---------------------------------------1.81 Lbs Max ---------------------------------------2.45 Lb Page 15 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Continued Thermal aging Initial o Mating Min ------------------------------------- 23.35 Lbs Max ------------------------------------- 28.22 Lbs o Unmating Min ------------------------------------- 19.60 Lbs Max ------------------------------------- 21.72 Lbs After thermal aging o Mating Min ------------------------------------- 18.92 Lbs Max ------------------------------------- 24.81 Lbs o Unmating Min ------------------------------------- 17.90 Lbs Max ------------------------------------- 20.40 Lbs Normal Force at 0.48 mm deflection Initial o Min -----------------------------------------------351.10 gf o Max---------------------------------------------- 413.00 gf Thermal o Min -----------------------------------------------354.20 gf o Max-----------------------------------------------404.80 gf Set------ 0.0150 mm Set------ 0.0300 mm Set ----- 0.0100 mm Set ----- 0.0200 mm LLCR Durability (192 pin LLCR test points) Initial --------------------------------------------------------------- 44.8 mOhms Max After 100 Cycles o <= +5.0 mOhms ------------------------------------ 191 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 1 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure After thermal shock o <= +5.0 mOhms ------------------------------------ 192 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 0 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure After humidity o <= +5.0 mOhms ------------------------------------ 188 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 4 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure Page 16 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Continued LLCR Thermal Aging (192 pin LLCR test points) Initial --------------------------------------------------------------- 44.8mOhms Max Thermal Aging o <= +5.0 mOhms ------------------------------------ 188 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 4 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure LLCR Gas Tight (192 pin LLCR test points) Initial --------------------------------------------------------------- 40.0 mOhms Max Gas-Tight o <= +5.0 mOhms ------------------------------------ 192 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 0 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure LLCR Shock Vib (192 pin LLCR test points) Initial --------------------------------------------------------------- 41.9 mOhms Max S&V o <= +5.0 mOhms ------------------------------------ 191 Points -------------------------Stable o +5.1 to +10.0 mOhms ---------------------------------- 1 Points -------------------------Minor o +10.1 to +15.0 mOhms--------------------------------- 0 Points -------------------------Acceptable o +15.1 to +50.0 mOhms--------------------------------- 0 Points -------------------------Marginal o +50.1 to +2000 mOhms -------------------------------- 0 Points -------------------------Unstable o >+2000 mOhms ----------------------------------------- 0 Points -------------------------Open Failure Mechanical Shock & Random Vibration: o Shock No Damage ----------------------------------- ----------------------------------Passed 50 Nanoseconds ------------------------------ ----------------------------------Passed o Vibration No Damage ----------------------------------- ----------------------------------Passed 50 Nanoseconds ------------------------------ ----------------------------------Passed Page 17 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST RESULTS Continued Insulation Resistance minimums, IR Pin-Pin Initial o Mated ------------------------------------------------10000Meg o Unmated---------------------------------------------10000Meg Thermal o Mated ------------------------------------------------10000Meg o Unmated---------------------------------------------10000Meg Humidity o Mated ------------------------------------------------10000Meg o Unmated---------------------------------------------10000Meg Dielectric Withstanding Voltage minimums, DWV Minimums o Breakdown Voltage -------------------------------- 1700VAC o Test Voltage ----------------------------------------- 1275VAC o Working Voltage ------------------------------------ 425VAC Pin - pin Initial DWV ------------------------------------------------- Passed Thermal DWV ---------------------------------------------- Passed Humidity DWV --------------------------------------------- Passed Page 18 of 55 -------------------------Pass -------------------------Pass -------------------------Pass -------------------------Pass -------------------------Pass -------------------------Pass Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES TEMPERATURE RISE (Current Carrying Capacity, CCC): 1) High quality thermocouples whose temperature slopes track one another were used for temperature monitoring. 2) The thermocouples were placed at a location to sense the maximum temperature generated during testing. 3) Temperature readings recorded are those for which three successive readings, 15 minutes apart, differ less than 1° C (computer controlled data acquisition). 4) Adjacent contacts were powered: a. Linear configuration with 2 adjacent conductors/contacts powered Base Curve 112488 2(2x1) Contacts in Linear series Part Numbers: IDSD-36-D-06.00-G/TST-136-01-G-D-01 Derated 20 % RT Peak Amp RT Derated Amp Measured Current 65 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 3.4 Amps 65 ° C Peak Amp 9.0 65 ° C Derated Amp Room Temp= 20.2C 75 ° C 75 ° C Peak Amp 8.0 75 ° C Derated Amp Limit 95 ° C Peak Amp Maximum Current, Amp per Contact 7.4 95 ° C Derated Amp 7.0 95 ° C Room Temp 6.0 5.9 5.0 5.0 4.0 4.0 105° C Limit 4.3 3.4 3.0 2.4 2.0 1.9 Useful Range 1.0 0.0 20 30 40 50 60 70 Ambient Temperature, ° C Page 19 of 55 80 90 100 110 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES b. Linear configuration with 4 adjacent conductors/contacts powered Base Curve 112488 4(2x2) Contacts in Linear series Part Numbers: IDSD-36-D-06.00-G/TST-136-01-G-D-01 Derated 20 % RT Peak Amp RT Derated Amp Measured Current 65 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.9 Amps 65 ° C Peak Amp 8.0 65 ° C Derated Amp Room Temp= 19.4 C 75 ° C 75 ° C Peak Amp 75 ° C Derated Amp 7.0 Limit 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp 95 ° C 6.0 Room Temp 5.0 105° C Limit 4.3 4.0 3.7 3.4 3.0 2.9 2.1 2.0 1.7 Useful Range 1.0 0.0 20 30 40 50 60 70 80 90 100 110 Ambient Temperature, ° C c. Linear configuration with 6 adjacent conductors/contacts powered Base Curve 112488 6(2X3) Contacts in Linear series Part Numbers:IDSD-36-D-06.00-G/TST-136-01-G-D-01 Derated 20 % RT Peak Amp RT Derated Amp Measured Current 65 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.4 Amps 65 ° C Peak Amp 6.0 65 ° C Derated Amp Room Temp= 20.4 C 75 ° C 75 ° C Peak Amp 75 ° C Derated Amp 5.2 Limit 5.0 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp 95 ° C Room Temp 4.2 4.0 105° C Limit 3.5 3.0 3.0 2.8 2.4 2.0 1.7 1.3 1.0 Useful Range 0.0 20 30 40 50 60 70 Ambient Temperature, ° C Page 20 of 55 80 90 100 110 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES d. Linear configuration with 8 adjacent conductors/contacts powered Base Curve 112488 8(2X4) Contacts in Linear series Part Numbers:IDSD-36-D-06.00-G/TST-136-01-G-D-01 Derated 20 % RT Peak Amp RT Derated Amp Measured Current 65 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.2 Amps 65 ° C Peak Amp 6.0 65 ° C Derated Amp Room Temp= 19.8 C 75 ° C 75 ° C Peak Amp 75 ° C Derated Amp Limit 5.0 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp 95 ° C Room Temp 4.0 105° C Limit 3.1 3.0 2.7 2.5 2.2 2.0 1.5 1.2 1.0 Useful Range 0.0 20 30 40 50 60 70 80 90 100 110 Ambient Temperature, ° C e. Linear configuration with all adjacent conductors/contacts powered Base Curve 112488 36(All) Contacts in Linear series Part Numbers:IDSD-36-D-06.00-G/TST-136-01-G-D-01 Derated 20 % RT Peak Amp RT Derated Amp Measured Current 65 ° C Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.6 Amps 65 ° C Peak Amp 4.0 65 ° C Derated Amp Room Temp= 21.3 C 75 ° C 75 ° C Peak Amp 75 ° C Derated Amp 3.5 Limit 3.4 95 ° C Peak Amp Maximum Current, Amp per Contact 95 ° C Derated Amp 95 ° C 3.0 Room Temp 2.7 2.5 105° C Limit 2.3 2.0 1.9 1.8 1.6 1.5 1.1 1.0 0.9 Useful Range 0.5 0.0 20 30 40 50 60 70 Ambient Temperature, ° C Page 21 of 55 80 90 100 110 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES CONTACT GAPS: Mating&Unmating durability: Initial Units: Minimum Maximum Average St. Dev. Count inches 0.0131 0.0186 0.0186 0.0019 120 After 100 Cycles Units: inches 0.0182 Minimum 0.0239 Maximum 0.0198 Average 0.0011 St. Dev. 120 Count inches 0.0106 0.0216 0.0186 0.0021 119 After Thermal Units: inches 0.0174 Minimum 0.0225 Maximum 0.0195 Average 0.0009 St. Dev. 120 Count Thermal aging: Initial Units: Minimum Maximum Average St. Dev. Count Normal force initial: Initial Units: inches 0.0171 0.0199 0.0173 0.0008 15 Minimum Maximum Average St. Dev. Count Normal force after thermal: Initial Units: Minimum Maximum Average St. Dev. Count inches 0.0178 0.0201 0.0187 0.0008 15 After Thermal Units: inches 0.0181 Minimum 0.0199 Maximum 0.0190 Average 0.0005 St. Dev. 15 Count Page 22 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST MATING/UNMATING FORCE: Mating/Unmating durability (Largest position submitted): Initial After 25 Cycles Mating Minimum Maximum Average S t Dev Count Unmating Mating Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 92.00 119.46 101.51 20.68 26.86 22.82 85.23 97.59 90.92 19.16 21.94 20.44 90.62 110.93 97.70 20.37 24.94 21.96 83.96 96.31 89.40 18.87 21.65 20.10 8.56 8 1.92 8 4.45 8 1.00 8 6.70 8 1.51 8 4.62 8 1.04 8 After 50 Cycles Mating Minimum Maximum Average S t Dev Count Unm ating Newtons After 75 Cycles Unmating Mating Unm ating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 85.62 102.39 94.03 19.25 23.02 21.14 81.31 95.14 88.26 18.28 21.39 19.84 81.01 100.33 92.23 18.21 22.56 20.74 80.62 92.49 86.70 18.13 20.79 19.49 5.71 8 1.28 8 4.91 8 1.10 8 6.42 8 1.44 8 4.38 8 0.98 8 After 100 Cycles Mating After Humidity Unmating Mating Unm ating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Minimum 80.42 18.08 79.44 17.86 79.15 17.79 78.07 17.55 Maximum 97.00 89.96 5.76 8 21.81 20.23 1.30 8 90.72 85.50 4.50 8 20.40 19.22 1.01 8 95.14 87.41 5.68 8 21.39 19.65 1.28 8 88.96 82.80 4.08 8 20.00 18.62 0.92 8 Average S t Dev Count Page 23 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES Mating/Unmating basic (middle position submitted): Initial After 25 Cycles Mating Minimum Maximum Average S t Dev Count Unmating Mating Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 47.67 55.61 50.84 10.72 12.50 11.43 45.80 50.51 48.33 10.30 11.36 10.87 46.10 53.16 49.35 10.36 11.95 11.09 44.82 50.02 47.24 10.08 11.25 10.62 2.95 8 0.66 8 1.52 8 0.34 8 2.81 8 0.63 8 1.60 8 0.36 8 After 50 Cycles Mating Minimum Maximum Average S t Dev Count After 75 Cycles Unmating Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 9.81 11.07 10.49 44.82 47.47 45.74 10.08 10.67 10.28 42.37 47.86 45.23 9.53 10.76 10.17 43.45 45.70 44.63 9.77 10.28 10.03 1.99 8 0.45 8 0.89 8 0.20 8 2.06 8 0.46 8 0.68 8 0.15 8 Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 41.19 9.26 42.86 9.64 Maximum 46.39 44.07 1.78 8 10.43 9.91 0.40 8 44.92 43.99 0.62 8 10.10 9.89 0.14 8 Count Unm ating 43.64 49.24 46.67 Mating S t Dev Mating Newtons After 100 Cycles Average Unm ating Newtons Page 24 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES Mating/Unmating basic (smallest position submitted): Initial After 25 Cycles Mating Minimum Maximum Average S t Dev Count Unmating Mating Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 10.89 15.01 12.97 2.45 3.37 2.92 9.51 15.40 11.46 2.14 3.46 2.58 9.42 13.14 11.29 2.12 2.95 2.54 7.75 12.16 9.87 1.74 2.73 2.22 1.40 8 0.31 8 1.87 8 0.42 8 1.27 8 0.28 8 1.51 8 0.34 8 After 50 Cycles Mating Minimum Maximum Average S t Dev Count Unm ating Newtons After 75 Cycles Unmating Mating Unm ating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 9.32 12.55 11.08 2.09 2.82 2.49 7.85 11.77 9.65 1.76 2.65 2.17 8.83 12.26 10.67 1.98 2.76 2.40 7.85 11.87 9.51 1.76 2.67 2.14 1.15 8 0.26 8 1.37 8 0.31 8 1.22 8 0.27 8 1.27 8 0.29 8 After 100 Cycles Mating Unmating Newtons Force (Lbs) Newtons Force (Lbs) Minimum 8.34 1.87 8.04 1.81 Maximum 11.48 10.11 1.02 8 2.58 2.27 0.23 8 10.89 9.26 0.86 8 2.45 2.08 0.19 8 Average S t Dev Count Thermal aging: Initial Mating Minimum Maximum Average S t Dev Count After Thermals Unmating Mating Unm ating Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) Newtons Force (Lbs) 103.87 125.54 114.84 23.35 28.22 25.82 87.19 96.61 92.02 19.60 21.72 20.69 84.15 110.34 97.56 18.92 24.81 21.93 79.64 90.72 85.99 17.90 20.40 19.33 7.36 8 1.66 8 3.27 8 0.74 8 8.44 8.00 1.90 8.00 3.89 8.00 0.87 8.00 Page 25 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES NORMAL FORCE Initial Averages Min Max St. Dev Count 0.1000 74.12 68.40 79.30 3.365 12 Deflections in mm Forces in Grams 0.2000 0.3000 0.4000 153.32 238.33 324.13 143.60 217.50 292.70 161.40 250.30 339.20 5.873 10.127 13.200 12 12 12 0.4800 388.78 351.10 413.00 16.509 12 SET 0.0202 0.0150 0.0300 0.0052 12 Deflections in mm Forces in Grams 0.2000 0.3000 0.4000 154.45 240.94 327.44 142.20 222.90 300.90 164.10 253.00 343.30 6.168 7.214 11.134 12 12 12 0.4800 390.00 354.20 404.80 14.632 12 SET 0.0273 0.0100 0.0400 0.0095 12 After Thermals Averages Min Max St. Dev Count 0.1000 73.41 65.70 80.70 4.090 12 INSULATION RESISTANCE (IR): Pin to Pin Minimum Mated IDSD/TST Unmated IDSD Unmated TST 10000 10000 10000 10000 10000 10000 10000 10000 10000 Initial Thermal Humidity DIELECTRIC WITHSTANDING VOLTAGE (DWV): Voltage Rating Summary Minimum IDSD/TST 1700 Break Down Voltage Test Voltage 1275 425 Working Voltage Pin to Pin Initial Test Voltage After Thermal Test Voltage After Humidity Test Voltage Page 26 of 55 Passed Passed Passed Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES LLCR Durabiltiy: 1) 2) 3) 4) A total of 192 points were measured. EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms-------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure Date Room Temp C RH Name mOhm values Average St. Dev. Min Max Count 2/26/2011 21 42% Peter Chen Actual Initial 37.8 1.8 36.6 44.8 192 3/1/2011 22 43% Peter Chen Delta 100 Cycles -0.7 1.3 -4.8 6.3 192 3/6/2011 20 40% Peter Chen Delta Thermal 0.8 1.5 -4.7 4.2 192 How many samples are being tested? How many contacts are on each board? 100 Cycles Thermal Humidity Stable 191 192 188 Minor 1 0 4 Acceptable 0 0 0 Page 27 of 55 Marginal 0 0 0 3/17/2011 22 50% Peter Chen Delta Humidity 1.0 1.8 -5.4 5.8 192 8 24 Unstable 0 0 0 Open 0 0 0 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES LLCR thermal aging 5) 6) 7) 8) A total of 192 points were measured EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms-------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure Date Room Temp C RH Name mOhm values Average St. Dev. Min Max Count 3/3/2011 23 45% Peter Chen Actual Initial 37.7 1.8 36.4 44.8 192 1/0/1900 0 0% 0 Delta Thermal Age 0.1 1.8 -8.1 4.3 192 How many samples are being tested? How many contacts are on each board? Thermal Age Stable 188 Minor 4 Acceptable 0 Page 28 of 55 Marginal 0 8 24 Unstable 0 Open 0 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES GAS TIGHT: 1) 2) 3) 4) A total of 192 points were measured EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms:------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure Date Room Temp C RH Name mOhm values Average St. Dev. Min Max Count 2/26/2011 23 45% Peter Chen Actual Initial 37.1 0.5 36.3 40.0 192 How many samples are being tested? How many contacts are on each board? Gas Tight Stable 192 Minor 0 Acceptable 0 Marginal 0 Page 29 of 55 1/0/1900 0 0% 0 Delta Gas Tight 1.0 0.9 -1.5 4.2 192 8 24 Unstable 0 Open 192 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA SUMMARIES S&V: 5) 6) 7) 8) A total of 192 points were measured EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets. A computer program, LLCR 221.exe, ensures repeatability for data acquisition. The following guidelines are used to categorize the changes in LLCR as a result from stressing. a. <= +5.0 mOhms:---------------------------- Stable b. +5.1 to +10.0 mOhms: --------------------- Minor c. +10.1 to +15.0 mOhms: ------------------- Acceptable d. +15.1 to +50.0 mOhms: ------------------- Marginal e. +50.1 to +2000 mOhms:------------------- Unstable f. >+2000 mOhms: ---------------------------- Open Failure Date Room Temp C RH Name mOhm values Average St. Dev. Min Max Count 5/5/2011 5/20/2011 23 32% Aaron McKim 22 44% Aaron Mckim Actual Initial 37.3 0.6 36.4 41.9 192 Delta Shock / Vibe 0.0 0.8 -4.5 7.5 192 How many samples are being tested? How many contacts are on each board? Shock / Vibe Stable 191 Minor 1 Acceptable 0 Page 30 of 55 Marginal 0 8 24 Unstable 0 Open 0 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA CONTACT GAPS Mating&Unmating durability Initial Units: inches Pos.# B1 B2 0.0188 0.0198 1 0.0181 0.0199 2 0.0195 0.0190 3 0.0189 0.0170 4 5 0.0187 0.0171 0.0196 0.0177 6 0.0185 0.0154 7 0.0185 0.0158 8 0.0180 0.0179 9 0.0186 0.0185 10 0.0184 0.0158 11 0.0192 0.0132 12 0.0191 0.0198 13 0.0173 0.0191 14 0.0189 0.0139 15 After 100 cycles Units: inches Pos.# B1 B2 1 0.0193 0.0214 0.0199 0.0215 2 0.0210 0.0190 3 0.0204 0.0207 4 0.0201 0.0205 5 0.0196 0.0239 6 0.0193 0.0199 7 0.0189 0.0191 8 0.0197 0.0192 9 0.0195 0.0205 10 0.0194 0.0200 11 0.0188 0.0199 12 0.0201 0.0194 13 0.0190 0.0190 14 0.0201 0.0191 15 B3 0.0172 0.0135 0.0136 0.0202 0.0143 0.0204 0.0166 0.0153 0.0188 0.0147 0.0186 0.0147 0.0195 0.0142 0.0131 B4 0.0194 0.0187 0.0139 0.0185 0.0186 0.0196 0.0202 0.0186 0.0186 0.0179 0.0176 0.0175 0.0163 0.0169 0.0178 B5 0.0185 0.0202 0.0211 0.0184 0.0197 0.0197 0.0186 0.0197 0.0197 0.0200 0.0202 0.0213 0.0197 0.0190 0.0197 B6 0.0190 0.0196 0.0196 0.0186 0.0205 0.0223 0.0187 0.0194 0.0197 0.0197 0.0197 0.0190 0.0197 0.0203 0.0197 B7 0.0211 0.0202 0.0197 0.0201 0.0186 0.0197 0.0187 0.0179 0.0197 0.0190 0.0197 0.0187 0.0197 0.0202 0.0179 B8 0.0176 0.0197 0.0201 0.0197 0.0187 0.0197 0.0186 0.0190 0.0197 0.0186 0.0210 0.0221 0.0211 0.0183 0.0187 B3 0.0191 0.0185 0.0192 0.0199 0.0212 0.0220 0.0223 0.0192 0.0206 0.0209 0.0224 0.0214 0.0199 0.0195 0.0195 B4 0.0198 0.0199 0.0193 0.0200 0.0192 0.0191 0.0216 0.0182 0.0183 0.0193 0.0194 0.0188 0.0192 0.0195 0.0197 B5 0.0206 0.0224 0.0199 0.0195 0.0199 0.0185 0.0198 0.0206 0.0189 0.0193 0.0184 0.0196 0.0209 0.0214 0.0185 B6 0.0197 0.0189 0.0194 0.0195 0.0189 0.0190 0.0190 0.0192 0.0194 0.0185 0.0186 0.0199 0.0207 0.0217 0.0213 B7 0.0213 0.0212 0.0216 0.0193 0.0192 0.0182 0.0199 0.0199 0.0210 0.0194 0.0198 0.0200 0.0196 0.0217 0.0183 B8 0.0193 0.0193 0.0197 0.0183 0.0182 0.0198 0.0193 0.0198 0.0192 0.0186 0.0182 0.0190 0.0184 0.0189 0.0193 Page 31 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued Thermal aging Pos.# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pos.# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Initial Units: inches B1 B2 0.0194 0.0181 0.0192 0.0175 0.0196 0.0185 0.0199 0.0191 0.0205 0.0195 0.0195 0.0190 0.0202 0.0199 0.0199 0.0186 0.0186 0.0188 0.0190 0.0206 0.0189 0.0212 0.0197 0.0199 0.0199 0.0197 0.0202 0.0197 0.0202 0.0197 After Thermal Units: inches B1 B2 0.0198 0.0190 0.0194 0.0209 0.0200 0.0202 0.0200 0.0202 0.0196 0.0196 0.0199 0.0216 0.0195 0.0198 0.0190 0.0197 0.0195 0.0195 0.0186 0.0198 0.0200 0.0197 0.0214 0.0200 0.0186 0.0193 0.0199 0.0193 0.0186 0.0212 B3 0.0174 0.0189 0.0176 0.0197 0.0188 0.0193 0.0197 0.0202 0.0206 0.0215 0.0211 0.0197 0.0187 0.0199 0.0175 B4 0.0187 0.0176 0.0187 0.0189 0.0172 0.0181 0.0197 0.0202 0.0202 0.0197 0.0187 0.0170 0.0187 0.0190 0.0201 B5 0.0135 0.0131 0.0116 0.0150 0.0130 0.0106 0.0206 0.0214 0.0197 0.0186 0.0179 0.0186 0.0201 0.0190 0.0205 B6 0.0141 0.0140 0.0132 0.0143 0.0151 0.0142 0.0187 0.0193 .0.02015 0.0197 0.0179 0.0201 0.0197 0.0186 0.0178 B7 0.0173 0.0180 0.0181 0.0188 0.0174 0.0186 0.0202 0.0197 0.0202 0.0186 0.0197 0.0197 0.0186 0.0165 0.0201 B8 0.0172 0.0189 0.0172 0.0181 0.0197 0.0170 0.0201 0.0197 0.0186 0.0205 0.0215 0.0202 0.0216 0.0190 0.0199 B9 0.0194 0.0192 0.0196 0.0199 0.0205 0.0195 0.0202 0.0199 0.0186 0.0190 0.0189 0.0197 0.0199 0.0202 0.0202 B10 0.0181 0.0175 0.0185 0.0191 0.0195 0.0190 0.0199 0.0186 0.0188 0.0206 0.0212 0.0199 0.0197 0.0197 0.0197 B3 0.0195 0.0196 0.0192 0.0196 0.0186 0.0194 0.0191 0.0198 0.0196 0.0196 0.0192 0.0184 0.0183 0.0191 0.0225 B4 0.0193 0.0206 0.0206 0.0201 0.0205 0.0203 0.0209 0.0207 0.0207 0.0214 0.0204 0.0203 0.0197 0.0198 0.0212 B5 0.0182 0.0195 0.0185 0.0194 0.0181 0.0188 0.0188 0.0212 0.0197 0.0195 0.0198 0.0191 0.0198 0.0185 0.0184 B6 0.0192 0.0190 0.0195 0.0211 0.0198 0.0194 0.0188 0.0194 0.0196 0.0185 0.0192 0.0191 0.0198 0.0182 0.0196 B7 0.0182 0.0174 0.0189 0.0196 0.0178 0.0212 0.0198 0.0195 0.0189 0.0185 0.0200 0.0193 0.0181 0.0185 0.0191 B8 0.0187 0.0189 0.0183 0.0187 0.0193 0.0190 0.0192 0.0188 0.0192 0.0194 0.0191 0.0191 0.0183 0.0199 0.0199 B9 0.0198 0.0194 0.0200 0.0200 0.0196 0.0199 0.0195 0.0190 0.0195 0.0186 0.0200 0.0214 0.0186 0.0199 0.0186 B10 0.0190 0.0209 0.0202 0.0202 0.0196 0.0216 0.0198 0.0197 0.0195 0.0198 0.0197 0.0200 0.0193 0.0193 0.0212 Page 32 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued Normal force initial: Initial Units:inches Pos.# B1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0.0198 0.0171 0.0181 0.0175 0.0183 0.0172 0.0190 0.0199 0.0186 0.0179 0.0187 0.0190 0.0188 0.0183 0.0187 Normal force after thermal aging: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Initial Unit: inches 0.0198 0.0181 0.0184 0.0183 0.0183 0.0180 0.0190 0.0186 0.0199 0.0201 0.0186 0.0179 0.0178 0.0190 0.0180 After Thermal Unit: inches 0.0196 0.0196 0.0192 0.0190 0.0187 0.0192 0.0186 0.0189 0.0181 0.0199 0.0187 0.0191 0.0195 0.0185 0.0191 Page 33 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued MATING\UNMATING FORCE Mating/Unmating durability: Initial Sample# 21 22 23 24 25 26 27 28 21 B 22 B 23 B 24 B 25 B 26 B 27 B 28 B After 25 Cycles After 50 Cycles After 100 Cycles After Humidity Mating Unmating Mating Unmating Mating Unmating Mating Unmating Mating Unmating 17.54 17.11 21.02 17.47 18.41 15.34 19.29 21.55 18.25 19.45 19.36 16.45 15.81 14.08 17.2 17.13 14.29 15.96 15.06 14.86 15.06 12.46 15.18 14.01 14.8 16.19 14.6 14.97 14.29 13.05 13.82 12.68 11.36 13.78 15.69 15.27 11.77 14.25 15.52 13.45 12.49 12.55 14.39 14.71 10.22 9.24 11.83 14.24 9.84 13.01 10.32 12.68 11.38 8.94 9.45 10.26 10.68 10 10.45 10.65 7.71 8.17 9.83 10.94 11.41 11.89 13.55 13.41 11.02 13.97 11.45 12.13 10.83 12.53 11.09 9.67 10.57 9.52 10.78 12.74 8.56 10.33 8.25 9.69 9.87 8.96 8.78 9.07 8.18 9.84 8.94 9.91 7.63 7.52 8.2 9.83 11.43 11.85 13.44 10.45 11.2 11.72 11.37 13 11.29 12.55 11.1 9.09 10.56 9.43 10.46 12.45 8.33 9.45 8.28 8.62 9.47 7.76 7.78 7.83 8.29 9.4 8.64 9.39 7.57 7.07 8.71 9.19 4.43 6.01 7.52 6.28 9.2 5.37 4.1 4.97 5.29 5.55 6.07 3.34 6.02 5.45 5.09 6.1 5.4 5.75 7.07 4.14 5.87 6.75 7.04 7.56 5.97 7.7 9.02 5.72 9.22 5.34 6.91 9.2 Mating/Unmating basic (middle position submitted): After 25 Cycles After 50 Cycles After 75 Cycles Sample# 1 Mating Initial Unmating Mating Unmating Mating Unmating Mating Unmating After 100 Cycles Mating Unmating 11.42 11.36 11.14 11.25 9.90 10.10 9.59 9.97 9.26 9.86 2 3 10.78 10.72 10.96 10.78 10.36 10.36 10.58 10.58 9.81 10.56 10.19 10.17 9.53 10.05 9.77 9.99 9.48 10.03 9.64 9.99 4 5 6 11.05 11.07 12.26 10.83 10.67 10.74 10.78 10.78 11.91 10.58 10.56 10.34 10.63 10.58 11.07 10.36 10.08 10.67 10.36 10.28 10.74 10.08 9.99 10.28 9.92 10.01 10.36 9.77 9.92 10.10 7 8 11.64 12.50 10.30 11.29 11.47 11.95 10.08 10.98 10.43 10.96 10.43 10.28 10.03 10.76 10.19 10.01 9.77 10.43 9.92 9.92 Mating/Unmating basic (smallest position submitted): After 25 Cycles After 50 Cycles After 75 Cycles Sample# 1 Mating Initial Unmating Mating Unmating Mating Unmating Mati ng Unmating Mating Unmating 2.76 2.38 2.51 2.27 2.32 2.23 2.23 2.14 2.09 2.09 2 3 2.45 2.89 2.14 2.56 2.49 2.89 1.96 2.58 2.49 2.82 1.98 2.54 2.43 2.76 2.03 2.36 2.32 2.58 2.05 2.23 4 5 6 3.37 3.35 2.84 2.82 3.46 2.56 2.95 2.29 2.12 2.73 2.38 1.74 2.82 2.43 2.09 2.65 2.23 1.76 2.76 2.29 1.98 2.67 2.21 1.85 2.54 2.21 1.87 2.45 2.09 1.94 7 8 2.71 2.95 2.18 2.51 2.65 2.40 1.92 2.16 2.65 2.32 1.87 2.09 2.54 2.21 1.76 2.09 2.36 2.23 1.81 1.98 Page 34 of 55 After 100 Cycles Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued Thermal aging: Initial After Thermals Sample# 1 Mating Unmating Mating Unmating 23.35 19.60 20.42 18.13 2 3 4 28.22 27.45 26.00 21.72 21.61 20.35 20.59 23.33 23.15 19.51 20.40 19.58 5 6 23.95 25.07 20.09 20.40 18.92 22.49 17.90 19.36 7 8 26.55 25.95 21.06 20.68 24.81 21.76 19.87 19.91 NORMAL FORCE Initial Sample # 1 2 3 4 5 6 7 8 9 10 11 12 After Thermals Sample # 1 2 3 4 5 6 7 8 9 10 11 12 0.1000 68.4 76.6 72.5 79.3 76.6 72.5 76.6 78.0 71.5 71.1 75.2 71.1 0.1000 75.2 67.0 73.9 80.7 76.6 75.2 76.6 72.5 72.5 65.7 72.5 72.5 Deflections in mm, Forces in Grams 0.2000 0.3000 0.4000 143.6 222.9 307.7 154.6 243.5 329.6 145.0 227.0 315.9 161.4 250.3 339.2 155.9 246.2 336.4 157.3 242.1 329.6 157.3 244.8 332.3 157.3 240.7 322.8 145.0 217.5 292.7 150.5 242.1 332.3 157.3 242.1 322.8 154.6 240.7 328.2 0.4800 376.1 403.5 378.8 413.0 408.9 394.7 388.5 385.8 351.1 392.3 381.8 390.9 SET 0.0230 0.0250 0.0300 0.0240 0.0200 0.0250 0.0200 0.0150 0.0150 0.0150 0.0150 0.0150 Deflections in mm, Forces in Grams 0.2000 0.3000 0.4000 153.2 244.8 328.2 145.0 233.9 317.3 154.6 240.7 331.0 158.7 246.2 343.3 164.1 253.0 340.6 158.7 243.5 336.4 158.7 240.7 321.4 151.8 240.7 328.2 157.3 242.1 326.9 142.2 222.9 300.9 157.3 242.1 326.9 151.8 240.7 328.2 0.4800 384.3 377.5 393.9 404.8 398.0 404.8 376.1 396.6 396.6 354.2 396.6 396.6 SET 0.0400 0.0400 0.0300 0.0300 0.0300 0.0200 0.0100 0.0240 0.0200 0.0400 0.0200 0.0240 Page 35 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued INSULATION RESISTANCE (IR): Initial Insulation Resistance Measured In Meg Ohms Sample# 112488-005 112488-006 Mated X IDSD/TST 10000 10000 Pin to Pin A Unmated B X X IDSD TST 10000 10000 10000 10000 Thermal Insulation Resistance Measured In Meg Ohms Sample# 112488-005 112488-006 Mated X IDSD/TST 10000 10000 Pin to Pin A Unmated B X X IDSD TST 10000 10000 10000 10000 Humidity Insulation Resistance Measured In Meg Ohms Sample# 112488-005 112488-006 Mated X IDSD/TST 10000 10000 Pin to Pin A Unmated B X X IDSD TST 10000 10000 10000 10000 Page 36 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA continued DIELECTRIC WITHSTANDING VOLTAGE (DWV): Initial Breakdown Voltage Test Voltage Until Breakdown Occurs Mated Sample# 112488-001 112488-002 IDSD/TST 1750 1700 Pin to Pin A Unmated X IDSD 2200 2000 B TST 2000 2300 Initial DWV Test Voltage= 1275 Sample# 112488-005 112488-006 Mated IDSD/TST 1275 1275 Pin to Pin A Unmated IDSD 1275 1275 B TST 1275 1275 Thermal Test Voltage Test Voltage= 1275 Sample# 112488-005 112488-006 Mated IDSD/TST 1275 1275 Pin to Pin A Unmated IDSD 1275 1275 B TST 1275 1275 Humidity Test Voltage Test Voltage= 1275 Sample# 112488-005 112488-006 Mated IDSD/TST 1275 1275 Pin to Pin A Unmated IDSD 1275 1275 Page 37 of 55 B TST 1275 1275 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA Continued LLCR Durability: Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 Actual Initial 37.5 37.8 37.4 37.7 38.7 38.2 38.3 39.3 39.1 38.3 37.9 37.6 37.5 38.0 38.0 38.1 38.8 37.6 38.4 38.4 39.1 39.1 38.7 39.1 44.8 44.8 44.5 44.6 44.2 44.5 43.8 44.3 43.3 43.6 42.7 42.3 41.5 41.1 40.4 40.5 39.4 39.4 39.0 38.6 38.4 Delta 100 Cycles -0.8 -1.1 -0.4 -0.5 -1.9 -0.6 -1.5 -1.9 -2.6 -1.4 -1.3 -1.0 -0.9 -1.4 -1.4 -0.2 -2.1 -1.0 -1.5 -1.2 -1.9 -2.2 -1.9 -2.1 -4.7 -4.8 -4.5 -4.3 -4.3 -4.5 -4.1 -4.2 -4.1 -3.9 -3.9 -3.3 -3.0 -2.6 -2.0 -2.1 -1.2 -2.0 -1.4 -0.9 -1.0 Page 38 of 55 Delta Thermal 0.2 -0.9 1.2 -0.4 0.5 0.4 0.4 0.5 -1.4 1.4 -0.6 -0.2 0.5 0.0 -0.7 0.1 0.0 -0.3 0.7 -0.1 -0.6 -1.9 -1.7 -1.4 -4.7 -4.1 -4.4 -4.4 -3.0 -1.7 -2.0 -3.9 -2.8 -2.5 -2.9 1.2 -2.2 -1.1 0.9 -0.1 1.2 -0.2 1.8 2.5 0.6 Delta Humidity 2.5 -1.2 4.0 -0.8 2.8 2.3 0.4 1.9 -0.1 0.8 0.0 -0.1 2.7 1.5 -0.8 0.2 1.3 1.0 1.1 0.6 1.5 -2.2 -2.0 -1.7 -2.5 -3.1 3.4 -1.4 -4.5 -5.4 -5.1 -1.8 -3.7 -4.4 -0.4 -1.5 -2.1 -2.5 -0.3 -1.2 1.1 -1.1 2.7 0.5 1.7 Tracking Code: 112488_Report_Rev_1 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 37.8 38.4 36.6 37.3 37.3 36.8 37.2 37.2 37.1 36.6 37.5 36.8 37.2 36.9 36.8 36.9 36.7 37.1 37.3 37.1 37.1 37.3 38.0 37.8 37.2 37.7 37.4 37.1 37.1 36.7 37.1 37.2 37.2 36.8 37.2 36.6 37.1 36.9 36.6 37.0 36.8 37.3 37.2 37.0 36.9 37.4 37.3 37.2 37.2 37.1 -0.5 -0.4 1.3 -0.6 -0.5 0.3 -0.1 -0.4 0.1 0.0 -0.1 -0.4 -0.3 -0.1 -0.2 -0.3 -0.2 -0.4 -0.3 -0.3 -0.2 0.5 -0.6 -0.3 0.2 -0.8 -0.2 -0.2 1.6 6.3 -0.1 -0.3 0.0 0.3 0.0 -0.2 -0.1 0.0 -0.2 -0.5 -0.1 -0.8 -0.3 -0.2 -0.1 -0.4 -0.1 -0.2 0.3 0.3 Page 39 of 55 -0.2 1.6 2.4 1.2 1.8 1.0 0.8 0.5 1.0 0.2 2.2 1.2 0.0 1.0 1.9 2.1 -0.1 1.4 3.2 0.3 1.2 1.5 0.8 1.3 1.3 -0.2 1.9 0.2 0.2 0.7 0.0 0.4 1.6 1.5 4.2 1.8 1.1 2.8 1.4 0.6 0.8 -0.4 0.9 -0.1 2.1 0.7 0.8 0.9 2.3 1.0 -0.5 5.5 3.2 1.8 1.7 0.6 0.7 0.1 1.3 -0.2 3.8 1.7 -0.3 0.9 1.7 4.1 -0.5 0.7 2.6 -0.1 2.9 0.4 1.8 2.0 0.9 -0.5 0.9 -0.1 -0.1 1.2 -0.3 0.3 0.6 1.2 4.9 1.3 2.3 2.9 1.2 -0.1 0.7 -0.7 0.9 -0.3 1.9 0.7 0.9 2.5 2.6 0.6 Tracking Code: 112488_Report_Rev_1 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 37.2 36.9 37.0 36.7 37.0 36.7 37.1 36.6 37.0 36.7 36.8 36.6 36.8 36.7 40.4 37.0 37.0 37.1 36.8 36.9 37.4 37.6 37.2 37.3 36.9 36.9 37.2 36.8 37.1 37.3 37.2 37.1 37.6 36.9 37.4 37.1 36.9 36.8 37.1 36.8 37.5 37.3 37.0 37.0 37.4 37.3 37.2 37.4 38.0 37.2 0.1 -0.3 -0.5 -0.1 -0.2 0.0 -0.4 -0.2 0.3 -0.4 0.2 0.1 -0.2 -0.1 -4.0 -0.5 0.0 -0.4 -0.2 -0.3 -0.1 -0.6 0.0 -0.5 0.9 -0.4 -0.5 -0.3 -0.3 -0.8 -0.4 -0.5 -0.3 -0.3 -0.6 -0.3 -0.4 -0.2 -0.5 -0.5 -0.6 -0.6 -0.1 -0.4 -0.2 0.0 -0.5 -0.3 -0.6 -0.4 Page 40 of 55 3.7 0.3 1.2 1.1 3.1 1.2 0.4 1.6 4.1 2.1 1.9 2.0 1.5 0.7 0.3 3.0 3.5 0.6 1.8 1.7 1.2 -0.4 1.1 0.7 3.4 2.0 1.1 0.0 0.0 3.1 4.0 1.0 3.1 1.3 0.9 2.0 0.7 0.6 0.2 -0.1 -0.1 1.0 1.3 -0.1 0.7 0.5 0.4 1.2 -0.2 0.4 4.0 -0.1 0.7 0.7 3.5 1.8 0.0 1.8 5.8 1.9 1.7 2.0 1.0 0.7 -1.1 3.1 3.8 0.2 1.0 1.7 2.8 -0.9 1.0 0.3 3.3 2.6 1.9 -0.4 -0.4 1.8 3.1 2.3 3.7 2.9 1.4 2.5 0.3 0.7 -0.1 -0.6 -0.5 0.6 2.0 -0.5 0.6 0.2 0.9 2.1 -0.4 4.1 Tracking Code: 112488_Report_Rev_1 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 36.8 36.6 37.1 37.1 37.5 36.8 37.8 36.7 37.2 36.9 36.7 36.6 37.1 37.0 37.1 37.0 37.3 37.1 37.1 37.0 37.3 37.6 37.2 37.0 37.1 37.3 37.3 37.0 37.3 36.9 37.4 36.8 37.0 37.5 37.1 37.1 36.8 37.3 37.3 37.0 37.2 37.5 37.6 37.5 37.4 37.6 37.3 -0.1 0.1 -0.5 -0.5 -0.4 -0.1 -0.7 1.4 -0.4 -0.1 0.0 0.0 -0.5 -0.4 -0.3 -0.3 -0.7 -0.4 -0.2 -0.2 -0.3 -0.3 0.8 0.2 1.3 -0.8 -0.4 0.4 0.1 -0.2 -0.3 -0.2 0.1 -0.7 -0.5 -0.7 -0.2 -0.6 -0.2 0.0 -0.3 -0.3 -0.2 -0.4 -0.4 -0.4 0.0 Page 41 of 55 3.0 1.1 1.4 0.3 3.7 1.2 -0.4 4.2 -0.1 -0.3 1.6 0.9 1.7 1.8 3.7 0.3 1.5 0.8 0.7 1.1 2.2 1.6 2.1 0.9 0.9 -0.5 2.1 0.8 1.9 0.5 0.0 0.8 1.0 1.5 0.9 0.5 0.2 1.2 0.9 2.4 2.0 2.7 1.0 0.8 0.9 1.3 1.6 3.1 0.6 1.1 -0.2 1.0 0.9 2.3 3.4 -0.7 3.7 1.1 0.4 1.9 1.7 3.5 -0.2 2.3 0.5 0.3 0.9 2.5 1.1 2.9 0.5 0.5 -0.9 2.0 0.6 3.7 0.9 2.2 0.7 3.9 2.7 1.6 2.3 -0.4 1.7 2.0 0.2 4.8 3.8 2.2 0.9 0.5 -0.1 1.9 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA Continued LLCR thermal aging Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 Actual Initial 37.4 37.7 37.3 37.6 38.8 38.1 38.3 39.3 39.1 38.2 37.8 37.4 37.4 37.9 37.9 38.0 38.8 37.4 38.4 38.3 39.2 39.0 38.6 39.0 44.8 44.8 44.4 44.6 44.2 44.5 43.8 44.2 43.3 43.5 42.6 42.3 41.4 41.0 40.3 40.5 39.3 39.3 38.9 38.5 38.3 Page 42 of 55 Delta Thermal age 0.7 0.7 1.1 1.6 4.0 2.2 -3.2 -2.7 -3.6 2.8 -1.5 0.7 -1.8 -0.2 1.8 2.2 -4.7 1.4 1.7 -0.9 -0.9 -4.9 4.1 2.8 -2.7 -2.4 -3.5 -3.6 -4.1 -4.3 -4.1 -4.2 -5.7 -5.7 -7.3 -8.1 0.6 -0.3 -2.1 -2.8 2.5 -3.1 -0.7 2.4 1.7 Tracking Code: 112488_Report_Rev_1 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 37.6 38.2 37.3 37.2 37.2 36.7 37.1 37.1 37.0 36.5 37.3 36.7 37.1 36.7 36.7 36.8 36.6 36.9 37.2 37.0 36.9 37.2 37.9 37.7 37.1 37.6 37.3 37.0 37.0 36.6 37.0 37.1 37.0 36.6 37.1 36.5 37.0 36.7 36.5 36.9 36.7 37.2 37.1 36.8 36.8 37.2 37.2 37.1 37.1 36.9 Page 43 of 55 1.8 1.0 -1.4 -0.7 0.4 -1.1 -0.9 -1.8 -0.4 3.0 -1.8 -0.2 0.5 -0.2 -0.2 1.9 3.6 4.3 -2.7 -0.6 1.6 2.3 -3.3 0.9 -0.5 -0.3 1.2 0.6 0.8 0.3 0.5 0.7 0.5 0.4 0.7 0.5 0.5 0.4 0.6 0.3 0.3 0.7 0.4 0.4 0.4 0.4 0.1 0.3 0.7 0.3 Tracking Code: 112488_Report_Rev_1 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 37.1 36.8 36.8 36.5 36.8 36.6 36.9 36.5 36.9 36.6 36.7 36.5 36.7 36.6 40.5 36.9 36.8 37.0 36.7 36.8 37.3 37.5 37.1 37.2 36.8 36.8 37.1 36.7 37.0 37.2 37.1 36.9 37.5 36.8 37.3 37.0 36.8 36.7 36.9 36.7 37.4 37.1 36.9 36.9 37.3 37.2 37.1 37.3 37.9 37.1 Page 44 of 55 0.4 0.5 0.8 0.9 0.6 0.7 0.7 0.8 0.4 0.5 0.7 0.4 1.2 0.6 -2.9 0.3 0.6 0.4 0.6 0.6 0.4 0.5 0.6 0.6 0.5 0.8 1.4 0.5 1.0 0.8 0.5 1.1 0.6 0.6 0.8 0.4 0.4 0.5 0.6 0.3 0.5 0.7 0.4 0.4 0.8 0.6 0.6 0.8 0.4 0.5 Tracking Code: 112488_Report_Rev_1 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 36.7 36.4 37.0 37.0 37.4 36.7 37.7 36.6 37.1 36.7 36.6 36.5 37.0 36.9 37.0 36.9 37.2 36.9 37.0 36.9 37.1 37.4 37.0 36.9 37.0 37.2 37.2 36.9 37.2 36.8 37.3 36.7 36.9 37.4 37.0 37.0 36.7 37.2 37.2 36.9 37.1 37.4 37.5 37.3 37.3 37.5 37.2 Page 45 of 55 0.6 0.6 0.3 1.4 1.2 0.5 1.7 0.6 0.9 0.9 0.9 0.3 0.6 0.8 0.2 1.0 0.6 0.4 0.3 0.3 0.9 0.6 0.9 0.4 0.8 0.6 0.7 0.7 0.5 0.8 0.8 0.5 0.8 0.6 0.8 0.4 0.6 0.7 0.7 1.0 0.9 1.1 0.8 0.6 0.7 0.6 0.7 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST DATA Continued LLCR Gas Tight Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 mOhm values Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 Actual Initial 37.5 37.2 37.3 37.2 37.1 37.6 37.1 37.3 36.7 36.9 36.9 36.9 36.7 36.9 37.4 37.1 37.3 37.0 37.2 37.4 37.5 37.8 37.6 37.5 37.0 37.2 36.6 36.5 36.9 37.1 36.7 37.2 36.6 36.9 36.8 36.6 36.5 36.9 36.8 37.0 36.9 36.8 37.0 37.2 36.7 Page 46 of 55 Delta Gas Tight 0.6 0.6 0.4 0.4 0.8 0.9 0.8 0.8 1.0 0.5 0.5 0.3 0.5 0.4 0.4 0.4 0.6 0.3 0.8 0.7 1.2 1.0 0.7 0.9 4.2 4.1 3.6 3.8 3.8 4.0 4.1 4.0 3.2 3.6 3.3 3.1 2.0 2.4 2.0 1.8 1.4 1.2 1.3 0.9 0.9 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 37.1 37.0 37.0 36.8 36.8 36.9 36.8 36.6 37.5 36.7 36.9 36.7 37.1 36.8 37.8 36.8 36.7 37.0 37.4 37.1 36.8 36.9 37.4 37.7 37.2 37.3 37.1 36.7 36.7 36.7 37.2 36.7 37.1 36.6 37.0 36.6 36.7 36.6 37.1 37.0 36.8 36.8 37.1 36.7 37.1 37.1 37.6 37.9 37.0 37.2 Page 47 of 55 1.3 0.8 1.0 0.7 0.9 1.2 1.0 1.1 1.3 2.1 1.5 0.6 1.1 0.3 0.6 0.4 0.7 0.4 0.4 0.6 0.4 0.8 0.7 0.6 1.1 1.2 1.0 0.4 0.8 1.0 0.8 0.9 0.9 0.7 0.7 0.7 1.1 0.5 0.9 1.1 0.9 0.4 0.5 0.4 0.5 0.4 0.9 1.3 1.1 1.6 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 37.0 36.6 36.7 36.8 36.8 36.8 36.9 36.5 37.0 36.7 36.8 36.6 36.6 36.6 36.3 36.6 37.0 36.5 36.4 36.5 37.1 37.1 37.3 36.8 37.2 37.1 36.8 37.2 37.2 37.1 37.3 36.9 37.3 36.8 37.4 37.1 37.0 36.9 37.0 36.8 37.3 37.0 36.7 36.9 37.3 37.4 37.4 37.2 37.2 38.8 Page 48 of 55 1.0 0.4 0.2 0.4 0.4 0.7 0.9 0.8 0.4 0.5 0.3 0.9 0.6 0.5 0.3 0.7 1.0 0.4 0.4 0.5 0.7 0.5 0.4 0.5 0.8 0.9 0.4 0.8 0.8 0.8 1.5 0.8 0.3 0.8 1.3 0.1 0.9 1.1 0.5 0.1 0.4 0.8 0.3 0.5 0.7 1.0 1.1 1.5 1.4 -1.1 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 37.9 37.3 37.5 36.8 38.5 37.0 40.0 37.0 37.7 36.8 37.0 36.7 37.8 36.9 37.3 37.1 37.8 37.4 39.0 38.0 39.0 38.1 37.8 36.5 36.7 36.4 36.8 36.5 37.1 36.7 37.1 36.5 36.9 36.7 36.5 36.4 36.5 36.5 37.1 36.8 36.7 36.8 37.2 37.1 37.0 38.0 37.1 Page 49 of 55 0.2 1.3 1.3 0.9 2.3 1.6 1.8 0.5 1.5 1.3 1.1 0.5 -0.5 0.7 0.9 0.7 1.1 0.5 -1.5 1.3 0.4 2.6 2.2 0.6 0.4 0.8 0.7 0.5 0.7 0.9 0.7 0.5 0.4 0.9 0.7 0.6 0.4 0.4 0.7 1.2 0.5 0.9 0.5 0.9 1.5 0.6 0.8 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST Data Continued LLCR S&V: mOhm values Board 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Position P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 Actual Initial 37.7 37.0 37.2 37.3 37.4 37.8 37.4 37.7 37.1 37.6 37.3 37.7 37.2 37.0 37.5 37.8 37.5 37.2 37.2 37.9 39.0 37.7 37.4 38.1 37.0 37.0 37.3 38.9 37.0 37.8 37.4 38.5 37.6 37.3 37.3 37.5 37.2 37.1 37.5 36.9 37.4 37.4 37.2 37.4 Page 50 of 55 Delta Shock / Vibe 0.0 0.0 0.1 0.0 0.0 0.2 0.0 0.1 0.2 0.2 0.1 -0.1 0.0 -0.1 -0.1 -0.3 0.3 0.3 0.3 0.1 0.6 0.8 0.3 0.4 0.0 0.0 0.0 -1.2 0.0 -0.3 -0.2 -0.4 0.1 -0.1 0.2 0.0 -0.1 -0.2 0.0 -0.1 -0.3 -0.3 0.1 -0.2 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 38.1 37.8 37.0 37.4 36.8 36.9 37.4 37.5 37.3 36.9 36.9 37.4 36.6 37.2 37.4 37.3 38.1 36.8 37.2 37.1 37.1 37.0 37.0 37.1 37.3 37.1 36.7 37.2 37.1 37.5 37.0 37.4 36.7 37.7 37.3 37.7 36.9 37.4 36.9 37.5 38.7 36.7 37.4 37.4 37.1 37.1 37.2 37.8 37.9 37.4 Page 51 of 55 -0.4 0.0 0.0 0.1 0.2 0.0 0.2 -0.2 -0.1 -0.1 0.2 0.0 0.1 0.0 0.0 0.0 -0.1 0.0 0.1 0.1 0.0 0.1 0.0 0.0 0.4 0.2 0.2 0.0 0.0 -0.2 -0.1 -0.3 -0.1 -0.1 -0.1 -0.3 -0.1 -0.2 -0.1 0.0 -0.2 0.1 -0.2 -0.3 -0.2 -0.2 0.0 0.0 0.4 0.2 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 4 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 37.5 37.4 36.9 36.9 36.9 37.1 37.7 37.1 37.7 37.3 36.8 37.2 37.2 37.5 37.1 37.1 37.2 37.0 37.1 37.0 37.4 37.4 37.2 37.4 36.9 37.3 37.2 37.0 36.9 37.2 37.1 37.6 36.8 37.3 36.7 37.6 41.9 36.6 36.4 36.6 37.2 37.6 37.0 36.8 36.9 37.3 37.4 37.2 37.3 37.4 Page 52 of 55 0.0 0.1 0.3 0.2 0.1 0.2 -0.4 0.6 -0.7 0.2 0.0 0.1 7.5 -0.9 -0.5 -0.5 0.1 0.3 -0.2 -0.2 -0.4 0.1 1.0 0.2 0.6 0.3 -0.1 0.0 0.1 0.2 0.8 -0.3 1.1 0.0 0.1 -0.4 -4.5 1.0 0.6 0.5 0.0 -0.6 0.1 0.2 0.7 0.6 -0.1 0.8 -0.3 -0.1 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 36.8 37.1 36.8 36.9 36.7 38.5 37.1 37.5 36.8 37.2 36.9 36.9 37.0 36.8 36.9 37.1 37.5 37.1 37.0 37.6 37.7 37.7 37.3 37.8 37.2 37.2 37.0 37.3 37.3 38.3 37.1 37.5 38.0 39.7 37.6 37.0 36.9 37.2 37.1 37.3 37.4 37.2 37.4 37.5 37.5 38.0 37.6 38.4 Page 53 of 55 0.4 0.0 0.2 0.2 0.6 -0.7 -0.1 -0.2 0.8 1.0 0.6 0.0 -0.3 0.2 0.1 0.2 -0.2 0.0 0.3 -0.1 -0.2 0.1 0.2 0.3 -0.3 -0.2 -0.2 -4.5 -0.6 -0.3 -0.4 0.0 -1.3 -2.6 -0.9 -0.1 0.0 -0.5 -0.3 -0.3 -0.5 -0.4 -0.6 -0.2 -0.2 -0.4 -0.4 -0.8 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST EQUIPMENT AND CALIBRATION SCHEDULES Equipment #: HZ-MO-03 Description: Micro-ohmmeter Manufacturer: Keithley Model: 580 Serial #: 297288 Accuracy: Last Cal: 2010-8-06, Next Cal: 2011-8-05 Equipment #: HZ-TCT-01 Description: Normal force analyzer Manufacturer: Mecmesin Multitester Model: Mecmesin Multitester 2.5-i Serial #: 08-1049-04 Accuracy: Last Cal: 2010-4-28, Next Cal: 2011-4-27 Equipment #: HZ-OV-01 Description: Oven Manufacturer: Huida Model: CS101-1E Serial #: CS101-1E-B Accuracy: Last Cal: 2010-12-14, Next Cal: 2011-12-13 Equipment #: HZ-THC-01 Description: Humidity transmitter Manufacturer: Thermtron Model: HMM30C Serial #: D0240037 Accuracy: Last Cal: 2010-3-3, Next Cal: 2011-3-2 Equipment #: HZ-OGP-01 Description: Video measurement system Manufacturer: OGP Model: SMARTSCOPE FLASH 200 Serial #: SVW2003632 Accuracy: Last Cal: 2010-6-10, Next Cal: 2011-6-9 Equipment #: HZ-MO-01 Description: Micro-ohmmeter Manufacturer: Keithley Model: 2700 Serial #: 1199807 Accuracy: Last Cal: 2010-4-28, Next Cal: 2011-4-27 Page 54 of 55 Tracking Code: 112488_Report_Rev_1 Part #: IDSD-36-D-06.00-G\TST-136-01-G-D-01 Part description: IDSD\TST EQUIPMENT AND CALIBRATION SCHEDULES Equipment #: HZ-PS-01 Description: Power Supply Manufacturer: Agilent Model: 6031A Serial #: MY41000982 Accuracy: Last Cal: 2010-4-28, Next Cal: 2011-4-27 Equipment #: HZ-TSC-01 Description: Thermal Shock transmitter Manufacturer: Keithley Model: 10-VT14994 Serial #: VTS-3-6-6-SC/AC Accuracy: Last Cal: 2010-11-1, Next Cal: 2011-11-1 Equipment #: ACLM-01 Description: Accelerometer Manufacturer: PCB Piezotronics Model: 352C03 Serial #: 115819 Accuracy: See Manual Last Cal: 2011-07-9, Next Cal: 2012-7-9 Equipment #: ED-03 Description: Event Detector Manufacturer: Analysis Tech Model: 32EHD Serial #: 1100604 Accuracy: See Manual Last Cal: 2011-06-4, Next Cal: 2012-06-4 Page 55 of 55 This document was created with Win2PDF available at http://www.win2pdf.com. The unregistered version of Win2PDF is for evaluation or non-commercial use only. This page will not be added after purchasing Win2PDF.