MICRF007 Micrel MICRF007 QwikRadio® Low-Power UHF Receiver General Description The MICRF007 is a single chip, ON-OFF Keyed (ASK/OOK) Receiver for remote wireless applications, employing Micrel’s latest QwikRadio® technology. This device is a true “antenna-in to data-out” monolithic device. All RF and IF tuning is accomplished automatically within the IC, which eliminates manual tuning, and reduces production costs. The result is a highly reliable yet extremely low cost solution. The MICRF007 is an enhanced version of the MICRF002 and MICRF011. The MICRF007 is a conventional superhetrodyne receiver, with an (internal) Local oscillator fixed at a single frequency based on an external reference crystal or clock. As with any conventional superhetrodyne receiver, the companion transmitter’s frequency must be accurately controlled, generally with a crystal or SAW (surface acoustic wave) resonator. The MICRF007 provides two enhancements over the MICRF001/011: (1) a Shutdown Mode, which may be used for duty-cycle operation, and (2) reduced current consumption. The MICRF007 requires a mere 2.3mA at 315MHz (3.8mA at 433.92MHz) when fully operational. These features make the MICRF007 ideal for low and ultra-low power applications, such as RKE and RFID. All post-detection (demodulator) data filtering is provided on the MICRF007, so no external baseband filters are required. The demodulator filter bandwidth is fixed at 2.5kHz. Data rates up to 3.2kbps NRZ may be used. All support documentation can be found on Micrel’s web site at www.micrel.com. QwikRadio® Features • • • • • • • • • Complete UHF receiver on a monolithic chip 300MHz to 440MHz Data rates up to 3.2kbps NRZ Automatic tuning, no manual adjustment Low power consumption – 315MHz: 2.3 mA fully operational 0.5µA shutdown 230µA polled at a 10:1 duty cycle ratio – 433.92MHz: 3.8mA fully operational 0.5µA shutdown 380µA polled at a 10:1 duty cycle ratio Virtually no RF re-radiation at the antenna CMOS logic interface to standard decoder and microprocessor ICs Extremely low external part count No filters or inductors required Applications • • • • Automotive remote keyless entry (RKE) Long range RF identification Remote fan and light control Garage door and gate openers Typical Application 50Ω�Ant MICRF007 1.8pF +5V 56nH VSS REFOSC ANT CAGC VDD SHUT CTH DO 0.039µF 4.8970MHz 2.2µF Data Output 315MHz 1200b/s On-Off Keyed Receiver QwikRadio is a trademark of Micrel, Inc. The QwikRadio ICs were developed under a partnership agreement with AIT of Orlando, Florida. Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com February 17, 2005 1 M9999-021705 MICRF007 Micrel Ordering Information Part Number Standard Pb-Free Junction Temp. Range Package MICRF007BM MICRF007YM –40°C to +85°C 8-pin SOIC Pin Configuration MICRF007BM VSS 1 8 REFOSC ANT 2 7 CAGC VDD 3 6 SHUT CTH 4 5 DO 8-Pin SOIC (M) Pin Description Pin Number Pin Name Pin Function 1 VSS Ground: Signal and power ground. 2 ANT Antenna (Analog Input): High-impedance, internally AC-coupled receiver input. For optimal performance, the ANT pin should be impedance matched to the antenna. 3 VDD Power Supply (Input): Positive supply input. Connect a low ESL, low ESR de-coupling capacitor from this pin to VSS. Lead lengths should be as short as possible. 4 CTH Data Slicing Threshold Capacitor (Analog I/O): Capacitor connected to this pin extracts the DC average value from the demodulated waveform which becomes the reference for the internal data slicing comparator. 5 DO Data Output (Digital Output): CMOS-level compatible data output signal. 6 SHUT Shutdown (Digital Input): Shutdown-mode logic-level control input. Pull low to enable the receiver. Internally pulled-up to VDD. 7 CAGC Automatic Gain Control (Analog I/O): Connect an external capacitor to set the attack/decay ratio of the on-chip automatic gain control. 8 REFOSC M9999-021705 Reference Oscillator: Timing reference, sets the RF receive frequency. 2 February 17, 2005 MICRF007 Micrel Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VDD)..................................................... +7V Input/Output Voltage (VI/O) ...................VSS–0.3 to VDD+0.3 Junction Temperature (TJ) ....................................... +150°C Storage Temperature Range (TS) ............. –65°C to +150°C Lead Temperature (soldering, 10 sec.) .................... +260°C ESD Rating(3) Supply Voltage (VDD)................................. +4.75V to +5.5V RF Frequency Range ...........................300MHz to 440MHz Data Duty-Cycle ............................................... 20% to 80% Reference Oscillator Input range .............. 0.1VPP to 1.5VPP Ambient Temperature (TA) .......................... –40°C to +85°C Package Thermal Resistance 8-pin SOIC (θJA) ................................................ 120°C/W Electrical Characteristics(4) Power supply: +4.75V ≤ VDD ≤ 5.5V, VSS = 0V; CAGC = 4.7µF, CTH = 0.047µF; fT = 6.7458MHz (equivalent of fRF = 433.92MHz); datarate = 600bps (Manchester encoded). TA = 25°C, bold values indicate –40°C ≤ TA ≤ +85°C; current flow into device pins is positive; unless noted. Symbol Parameter Condition IOP Operating Current at 315.0MHz Operating Current at 433.92MHz ISTBY Standby Current fIF IF Center Frequency RF Section, IF Section Receiver Sensitivity fBW Typ Max Units continuous operation 2.3 3.5 mA polled with 10:1 duty cycle 230 continuous operation 3.8 polled with 10:1 duty cycle 470 VSHUT = VDD 0.9 fRF = 433.92MHz, 1.2kbps Note 7 IF Bandwidth Notes 6, 7 Maximum Receiver Input Ref. Impedance = 50Ω 0.4 Spurious Reverse Isolation ANT pin, Ref. Impedance = AGC Attack to Decay Ratio tATTACK ÷ tDECAY AGC Leakage Current 50Ω(8) µA 5.7 mA µA 2 µA –99 dBm 1.18 MHz 0.70 MHz –20 dBm 30 µVrms 10 TA = +85°C ±50 nA to 1% of final value 2.5 ms Reference Oscillator Input Impedance 290 kΩ Reference Oscillator Source Current 5.2 µA Reference Oscillator(9) Reference Oscillator Stabilization Time ZREFOSC Min Demodulator ZCTH ΔZCTH IZCTH(leak) CTH Source Impedance Note 10 CTH Leakage Current TA = +85°C ±50 nA 2.5 kHz VSHUT = VSS 8 µA CTH Source Impedance Variation Demodulator Filter Bandwidth 110 –15 Note 7 kΩ +15 % Digital/Control Section IIN(pu) Input Pull-Up Current VIL Input Low Voltage VIH Input High Voltage February 17, 2005 VSHUT = VSS VSHUT = VSS 3 0.8VDD V 0.2VDD V M9999-021705 MICRF007 Symbol Micrel Parameter Condition Min Typ Max Units Output High Current 20.8 µA IOL Output Low Current 17.6 µA VOL Output Low Voltage IOH VOH Output High Voltage tR, tF Output Rise and Fall Times DO, IOUT = –1µA DO, IOUT = +1µA DO, CLOAD = 15pF 0.9VDD V 10 0.1VDD V µs Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are E� MIL-STD-883C, method 3015. Do not operate or store near strong electrostatic fields. 4. Specification for packaged product only. 5. Sensitivity is defined as the average signal level, measured at the input, necessary to achieve 10-2 BER (bit error rate). The input signal is defined as a return-to-zero (RZ) waveform with 50% average duty cycle (Manchester encoded data) at a data rate of 600bps. The RF input is assumed to be matched into 50Ω. 6. Sensitivity, a commonly specified receiver parameter, provides an indication of the receiver’s input referred noise, generally input thermal noise. However, it is possibl� noise is appreciab� A better indicator of achievable receiver range performance is usually given by its selectivity, often stated as intermediate frequency (IF) or radio frequency (RF) bandwidth, depending on receiver topology. Selectivity is a measure of the rejection by the receiver of ambient noise. More selective receivers will almost inva� ally thermal will the receiver demonstrate sensitivity-limited performance. 7. Parameter scales linearly with reference oscillator frequency fT. For any reference oscillator frequency other than 6.7458MHz, compute the parameter value as the ratio: fTMHz 6.7458 × (parameter value at 6.7458MHz) Example: For reference oscillator freqency fT = 6.00MHz: 6.7458 (parameter value at 6.00MHz)= × (parameter value at 6.7458MHz) 6.00 8. Spurious reve� ing network. - 9. Series resistance � resistance is too great, the oscillator may oscillate at a diminished peak-to-peak level, or may fail to oscillate entirely. Micrel recommends that series resistances for ceramic resonators and crystals not exceed 50Ω and 100Ω respectively. Refer to “Application Hint 35” for crystal recommendations. 10. Parameter scales inversely with reference oscillator frequency fT. For any reference oscillator frequency other than 6.7458MHz, compute the parameter value as the ratio: 6.7458 fTMHZ × (parameter value at 6.7458MHz) Example: For reference oscillator frequency fT = 6.00MHz: 6.7458 × (parameter value at 6.7458MHz) (parameter value at 6.00MHz) = 6.00 M9999-021705 4 February 17, 2005 MICRF007 Micrel Typical Characteristics Supply Current vs. Frequency 6.0 T A = 25°C V DD = 5V 3.5 Supply Current vs. Temperature f = 315MHz V DD = 5V Continuous Operation 3.0 4.5 2.5 3.0 2.0 Continuous Operation 1.5 300 325 350 375 400 425 450 FREQUENCY (MHz) February 17, 2005 1.5 -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) 5 M9999-021705 MICRF007 Micrel Functional Diagram CAGC AGC Control CAGC ANT 5th Order Band-Pass Filter RF Amp f RX fIF fLO IF Amp IF Amp Peak Detector 430kHz 2nd Order Programmable Low-Pass Filter SwitchedCapacitor Resistor RSC Comparator VDD UHF Downconverter OOK Demodulator CTH Control Logic SHUT REFOSC Cystal or Ceramic Resonator CTH Synthesizer VSS DO fT Reference Oscillator Reference and Control MICRF007 MICRF007 Block Diagram Applications Information and Functional Description Design Steps The following steps are the basic design steps for using the MICRF007 receiver: 1. Select the reference oscillator 2. Select the CTH capacitor 3. Select the CAGC capacitor Refer to the functional diagram. Three sections of the IC are identified: UHF Down-converter, OOK Demodulator and Reference and Control. Also shown are two capacitors (CTH, CAGC) and one timing component (Y1), usually a crystal. With the exception of a supply decoupling capacitor, these are the only external components needed by the MICRF007 to assemble a complete UHF receiver. For optimal performance, MICRF007 input impedance must be matched to the antenna impedance. The matching network will add an additional two or three components. There is one control input, SHUT pin. The SHUT function is used to enable the receiver. This input is CMOS compatible, and is pulled-up on the IC. Roll-off response of the IF Band-Pass Filter is 5th order, while the demodulator data filter exhibits a 2nd order response. The MICRF007 is a standard super-heterodyne receiver with a narrow IF filter bandwidth of 700kHz. It is less susceptible to interfering RF signals. The MICRF007 RF center frequency is controlled by an integrated PLL/VCO frequency synthesizer, which is locked to the reference oscillator frequency, typically set by a crystal. A tight tolerance transmitter such as SAW or crystal-based transmitters must be used for the system. The MICRF007 has a fully integrated base-band demodulator filter. The filter has a fixed 2.5kHz bandwidth and exhibits a 2nd order response. This filter limits the receiver raw data rate to 3.2Kbps NRZ. M9999-021705 Step 1: Selecting Reference Oscillator All timing and tuning operations on the MICRF007 are derived from the internal Colpitts reference oscillator. Timing and tuning is controlled through the REFOSC pin in one of two ways: 1. Connect a crystal. 2. Drive this pin with an external timing signal. The specific reference frequency required is related to the system transmit frequency. Crystal Selection Care should be taken to ensure low ESR crystals are selected. “Application Hint 35” provides additional information and recommended sources for crystals. When a crystal is used, the minimum voltage is 300mVPP. If using an externally applied signal, it should be AC-coupled and limited to the operating range of 0.1VPP to 1.5VPP. Selecting Reference Oscillator Frequency fT As with any super-heterodyne receiver, the difference between the internal local oscillator (LO) frequency fLO and the incoming transmit frequency fTX should equal the IF center frequency. Equation 1 may be used to compute the 6 February 17, 2005 MICRF007 Micrel Step 3: Selecting CAGC Capacitor The signal path has automatic gain control (AGC) to increase input dynamic range. The attack time constant of the AGC is set externally by the value of the CAGC capacitor connected to the CAGC pin of the device. To maximize system range, it is important to keep the AGC control voltage ripple low, preferably under 10mVPP once the control voltage has attained its quiescent value. For this reason, capacitor values of at least 0.47µF are recommended. The AGC control voltage is carefully managed on-chip to allow duty-cycle operation of the MICRF007. When the device is placed into shutdown mode (SHUT pin is pulled high), the AGC capacitor floats to retain the voltage. When operation is resumed, only the voltage droop due to capacitor leakage must be replenished. A relatively low-leakage capacitor is recommended when the devices are used in duty-cycled operation. To further enhance duty-cycled operation, the AGC push and pull currents are boosted for approximately 10ms immediately after the device is taken out of shutdown. This compensates for AGC capacitor voltage droop and reduces the time to restore the correct AGC voltage. The current is boosted by a factor of 45. Selecting CAGC Capacitor in Continuous Mode A CAGC capacitor in the range of 0.47µF to 4.7µF is typically recommended. Caution! If the capacitor is too large, the AGC may react too slowly to incoming signals. AGC settling time from a completely discharged (zero-volt) state is given approximately by this equation: ∆t = 1.333 × CAGC –0.44 (5) where: CAGC is in µF, and ∆t is in seconds. Selecting CAGC Capacitor in Duty-Cycle Mode Voltage droop across the CAGC capacitor during shutdown should be replenished as quickly as possible after the IC is enabled. As mentioned above, the MICRF007 boosts the push-pull current by a factor of 45 immediately after start-up. This fixed time period is based on the reference oscillator frequency fT. The time is 10.9ms for fT = 6.00MHz, and varies inversely with fT. The value of CAGC capacitor and the duration of the shutdown time period should be selected such that the droop can be replenished within this 10ms period. Polarity of the droop is unknown, meaning the AGC voltage could droop up or down. The worst-case from a recovery standpoint is downward droop, since the AGC pull-up current is 1/10th magnitude of the pull-down current. The downward droop is replenished according to the Equation 6: appropriate fLO for a given fTX: f � � fLO = fTX± �1.18 TX � (1) � 433.92 � Frequencies fTX and fLO are in MHz. Note that two values of fLO exist for any given fTX, distinguished as “high-side mixing” and “low-side mixing.” High-side mixing results in an image frequency above the frequency of interest and lowside mixing results in a frequency below. There is generally no preference of one over the other. After choosing one of the two acceptable values of fLO, use Equation 2 to compute the reference oscillator frequency fT: fT = fLO (2) 64.5 Frequency fT is in MHz. Connect a crystal of frequency fT to REFOSC on the MICRF007. Four-decimal-place accuracy on the frequency is generally adequate. The following table identifies fT for some common transmit frequencies. Transmit Reference Frequency fTX Oscillator Frequency fT 315MHz 4.8970MHz 390MHz 6.0630MHz 418MHz 6.4983MHz 433.92MHz 6.7458MHz Table 2. Recommended Reference Oscillator Values for Typical Transmit Frequencies (high-side mixing) Step 2: Selecting CTH Capacitor Extraction of the DC value of the demodulated signal for purposes of logic-level data slicing is accomplished using the external threshold capacitor CTH and the on-chip switched capacitor “resistor” RSC, shown in the block diagram. Slicing level time constant values vary somewhat with decoder type, data pattern, and data rate, but typically values range from 5ms to 50ms.This issue is covered in more detail in “Application Note 22.” Optimization of the value of CTH is required to maximize range. τ of 5x the bit-rate is recommended. The effective resistance of RSC is listed in the electrical characteristics table as 110kΩ at 433.92MHz, This value scales inversely with frequency. Source impedance of the CTH pin at other frequencies is given by equation (3), where fT is in MHz: RSC = 110kΩ 6.7458 fT (3) Since slicing level time constant τ has been established as 5 times bit rate, capacitor CTH may be computed using equation (4), CTH= CAGC= (6) where: I = AGC pull-up current for the initial 10ms (67.5µA) CAGC = AGC capacitor value ∆t = droop recovery time RSC (4) A standard ±20% X7R ceramic capacitor is generally sufficient. Refer to “Application Hint 42” for CTH and CAGC selection examples. February 17, 2005 It V 7 M9999-021705 MICRF007 Micrel ∆V = droop voltage For example, if user desires ∆t = 10ms and chooses a 4.7µF CAGC, then the allowable droop is about 144mV. Using the same equation with 200nA, the worst case pin leakage, and assuming 1µA of capacitor leakage in the same direction, the maximum allowable ∆t (shutdown time) is about 0.56s for droop recovery in 10ms. The ratio of decay-to-attack time-constant is fixed at 1:10 (that is, the attack time constant is 10 times of the delay time constant). Generally, the design value of 1:10 is adequate for the vast majority of applications. If adjustment is required, adding a resistor in parallel of the CAGC capacitor may vary the ratio. The value of the resistor must be determined on a case by case basis. Additional Applications Information In addition to the basic operation of the MICRF007, the following enhancements can be made. In particular, it is strongly recommended that the antenna impedance is matched to the input of the IC. Antenna Impedance Matching As shown in Figure 2 and Table 3, the antenna pin input impedance is frequency dependent. The ANT pin can be matched to 50Ω with a high pass circuit as shown in Figure 3. That is, a shunt inductor from the antenna input to ground and a capacitor in series from the antenna input to the ANT pin. j100 j25 � 50 0 –j25 Fr eq u en c y (MHz) ZIN( Ω ) Z11 S11 CSERIES (pF) 300 12– j16 6 0.803– j0.52 9 1.5 62 305 12– j16 5 0.800– j0.53 0 1.4 62 310 12 – j16 3 0.796– j0.53 6 1.6 56 315 13 – j16 2 0.791– j0.53 6 1.5 56 320 12 – j16 0 0.789– j0.54 3 1.4 56 325 12 – j15 7 0.782– j0.55 0 1.7 51 330 12 - j15 5 0.778– j0.55 6 1.5 51 335 12 – j15 2 0.770– j0.56 4 1.4 51 340 11 - j15 0 0.767– j0.57 2 1.6 47 345 11 – j14 8 0.762– j0.57 8 1.5 47 350 11 – j14 5 0.753– j0.58 6 1.4 47 355 11 – j14 3 0.748– j0.59 2 1.6 43 360 11 – j14 1 0.742– j0.59 7 1.5 43 365 11 – j13 9 0.735– j0.60 3 1.4 43 370 10 – j13 7 0.732– j0.61 1.3 43 375 10 – j13 5 0.725– j0.61 9 1.6 39 380 10 – j13 3 0.718– j0.62 5 1.4 39 LSHUNT (nH) 385 10 – j13 1 0.711– j0.63 1 1.3 39 390 10 – j13 0 0.707– j0.63 4 1.2 39 395 10 – j12 8 0.700– j0.64 1 1.5 36 400 10 – j12 6 0.692– j0.64 7 1.4 36 405 10 – j12 4 0.684– j0.65 3 1.2 36 410 10 – j12 2 0.675– j0.66 0 1.5 33 415 10 – j12 0 0.667– j0.66 7 1.4 33 420 10 – j11 8 0.658– j0.67 3 1.3 33 425 10 – j11 7 0.653– j0.67 7 1.6 30 430 10 – j11 5 0.643– j0.68 4 1.5 30 435 10 – j11 4 0.638– j0.68 7 1.4 30 440 8 – j11 2 0.635– j0.70 4 1.2 30 Table 4. Input Impedance vs. Frequency –j100 Figure 2. Impedance Looking into Antenna Pin CSERIES ANT Pin LSHUNT Figure 3. Antenna Impedance Matching Network M9999-021705 8 February 17, 2005 MICRF007 Micrel I/O Pin Interface Circuitry Inductor values may be different from Table 4, depending on PCB material, PCB thickness, ground configuration, and how long the traces are in the layout. Values shown were charac-terized for a 0.031 inch thickness, FR4 board, solid ground plane on bottom layer, and very short traces. Murata and Coilcraft wire-wound 0603 or 0805 surface mount inductors were tested, however, any wire-wound inductor with high SRF (self-resonance frequency) should do the job. Shutdown Function Duty-cycled operation of the MICRF007 (often referred to as polling) is achieved by turning the MICRF007 on and off via the SHUT pin. The shutdown function is controlled by a logic state applied to the SHUT pin. When VSHUT is high, the device goes into low-power standby mode. This pin is pulled high internally, it must be externally pulled low to enable the receiver. It is recommended to connect this pin through a 100kΩ resistor to ground Power Supply Bypass Capacitors Power supply bypass capacitor(s) connected to VDD should have the shortest possible lead lengths to VSS. Increasing Selectivity with Optional Band-Pass Filter For applications located in high ambient noise environments, a fixed value band-pass network may be connected between the ANT pin and VSS to provide additional receiver selectivity and input overload protection. A minimum input configuration is included in Figure 10. It provides some filtering and necessary overload protection. Data Squelching During quiet periods (no signal), the data output (DO pin) transitions randomly with noise. Most decoders can discriminate between this random noise and actual data. But for some system, it does present a problem. There are three possible approaches to reduce this output noise: Interface circuitry for the various I/O pins of the MICRF007 are diagrammed in Figures 4 through 9. The ESD protection diodes at all input and output pins are not shown. ANT Pin Active Load 50 Active Bias 6k Figure 4. ANT Pin The ANT pin is internally AC-coupled via a 3pF capacitor to an RF N-Channel MOSFET, as shown in Figure 4. Im-pedance on this pin to VSS is quite high at low frequencies, and decreases as frequency increases. In the UHF fre-quency range, the device input can be modeled as 6.3k. in parallel with 2pF (pin capacitance) to VSS. CTH Pin VDD 1.5A 67.5A Comparator CAGC Timout Figure 5. CTH Pin 15A 675A Figure 5 illustrates the CTH-pin interface circuit. The CTH pin is driven from a P-Channel MOSFET source-follower VSS with approximately 10µA of bias. Transmission gates TG1 and TG2 isolate the 6.9pF capacitor. Internal control signals PHI1/PHI2 are related in a manner such that the impedance across the transmission gates looks like a “resistance” of approximately 110kΩ. The DC potential at the CTH pin is approximately 1.6V CAGC Pin Figure 6 illustrates the CAGC pin interface circuit. The AGC control voltage is developed as an integrated current into a capacitor CAGC. The attack current is nominally 1.5µA, while the decay current is a 10 times scaling of this, approximately 15µA. Signal gain of the RF/IF strip inside the IC diminishes as the voltage on CAGC decreases. By simply adding a capacitor to CAGC pin, the attack/decay time constant ratio is fixed at 10:1. Modification of the attack/decay ratio is possible by adding resistance from the CAGC pin to either VDD or VSS, as desired. Both the push and pull current sources are disabled during shutdown, which maintains the voltage across CAGC, and improves recovery time in duty-cycled applications. To further improve duty-cycle recovery, both push and pull currents are increased by 45 times for approximately 10ms after release of the SHUT pin. This allows rapid recovery of any voltage drop on CAGC while in shutdown. 1. Analog squelch to raise the demodulator threshold 2. Digital squelch to disable the output when data is not present 3. Output filter to filter the (high frequency) noise glitches on the data output pin. The simplest solution is to add analog squelch by introducing a small offset, or squelch voltage, on the CTH pin so that noise does not trigger the internal comparator. Usually 20mV to 30mV is sufficient, and may be achieved by connecting a several-meg-ohm resistor from the CTH pin to either VSS or VDD, depending on the desired offset polarity. Since MICRF007’s receiver AGC noise at the internal comparator input is always the same (set by the AGC), the squelch offset requirement does not change as the local noise strength changes from installation to installation. Introducing squelch will reduce sensitivity and also reduce range. Only introduce an amount of offset sufficient to quiet the output. Typical squelch resistor values range from 10MΩ to 6.8MΩ for low to high squelch strength. February 17, 2005 3pF 9 M9999-021705 MICRF007 Micrel REFOSC Pin VDD 1.5A VDDBB Active Bias 67.5A 200k REFOSC Comparator 30pF CAGC 250 30pF 30µA VSSBB Timout 15A 675A VSSBB Figure 8. REFOSC Pin The reference oscillator (REFOSC) input circuit is shown in Figure 8. Input impedance is high (290kΩ). This is a Colpitts oscillator with internal 30pF capacitors. This input is intended to work with standard crystal connected from this pin to the VSS pin. The nominal DC bias voltage on this pin is 1.4V. SHUT Pin VSS Figure 6. CAGC Pin DO Pin The output stage for the digital output (DO) in Figure 7. The output is a 20µA push and 18µA pull switched-current stage. This output stage is capable of driving CMOS loads. An external buffer-driver is recommended for driving high capacitance loads. VDDBB Q1 VDD Q2 to Internal Circuits VSSBB SHUT 20µA Comparator Q3 VSSBB DO Figure 9. SHUT Pin Control input circuitry is shown in Figure 9. The standard input is a logic inverter constructed with minimum geometry MOSFETs (Q2, Q3). P-Channel MOSFET Q1 is a large channel length device, which functions essentially as a “weak” pull-up to VDD. Typical pull-up current is 5µA. 18µA VSS Figure 7. DO Pin M9999-021705 10 February 17, 2005 MICRF007 Micrel Application Example Operation in this example is at 315MHz, and may be customized by selection of the appropriate frequency reference (Y1), and adjustment of the antenna length. Changes from the 1Kbps data rate may require a change in the value of R1. A bill of materials accompanies the schematic. 315MHz Receiver/Decoder Application Figure 10 illustrates a typical application for the MICRF007 UHF Receiver IC. This receiver operates continuously (not duty cycled) in fixed-mode, and features 6-bit address decoding and two output code bits. +5V Supply Input 1/4 monopole antenna (23.1cm) 6-bit address U1 MICRF007 VSS REFOSC C4 1.8pF L1 56nH C1 C5 4.7µF 100µF C6 100pF C2 39nF ANT CAGC VDD SHUT CTH DO Y1 4.8970MHz C3 2.2µF R3 100k U2 HT-12D A0 A1 A2 A3 A4 VDD VT OSC1 OSC2 DIN A5 A6 D11 D10 A7 D9 VSS D8 R2 1k R1 68k Code Bit 0 Code Bit 1 RF Baseband (Analog) (Digital) Ground Ground Figure 10. 315MHz, 1Kbps On-Off Keyed Receiver with Decoder Bill of Materials Item Part Number Manufacturer Description C1 GRM21BF51A475ZA01L Murata(7) 4.7µF Y5V Qty. C2 VJ0603Y393KXXA Vishay(1) 39nF 1 C3 GRM188R61A225XE348 Murata(7) 2.2µF X5R 1 C4 GRM1885C1H1R8CZ01B Murata(7) 1.8pF COG ceramic capacitor 1 C5 GRM188R71E104KA01B Murata(7) 100nF capacitor 1 C6 GRM1885C1H101JA01B Murata(7) 100pF capacitor 1 D1 SSF-LX100LID Lumex(2) red LED 1 L1 0603CS-56NX-B Coilcraft(6) 56mH wire wound, Q=38 1 R1 CRCW06036812F Vishay(1) 68k; 1/4W; 5% 1 R2 CRCW06031001F Vishay(1) 1k; 1/4W; 5% 1 R3 CRCW06031003F Vishay(1) 100k 1 U1 MICRF007BM Micrel(3) UHF Reciever 1 U2 HT-12D Holtek(4) Logic decoder 1 Y1 AB-4.8970MHZ-20-D Abracon(5) 4.8970MHz crystal 1 1 Notes: 1. Vishay, tel. (203) 268-6261 2. Lumex, tel. (800) 278-5666 3. Micrel Inc., tel (408) 944-0800 4. Holteck, tel (408) 894-9046 5. Abracon, tel. (949) 448-7070 6. Coilcraft, tel. (510) 814-8954 7. Murata, tel (408) 397-1284 February 17, 2005 11 M9999-021705 MICRF007 Micrel PCB Layout Information The MICRF007 evaluation board was designed and characterized using double sided 0.031 inch thick FR4 material with 1 ounce copper clad. If another type of printed circuit board material is substituted, impedance matching and characterization data may not be as stated in this document. PCB Silk Screen PCB Component Side Layout PCB Solder Side Layout 1 2 +5V ANT1 50½ Ant J2 (np) SMA 1 C3 2.0pF 50V 2 +5V L1 (np) U1 MICRF007BM L2 27nH 3 R1 (np) 4 VSS REFOSC ANT CAGC VDD SHUT CTH DO 8 C2 (np) C1 (np) CAGC REFOSC GND J1 (np) CON2 7 SH 6 5 C4 CAGC Y1 6.7458MHz DO +5V +5V GND DO SH 1 2 3 4 5 L3 (np) ZCB-0603 +5V C5 0.1µF 16V C6 (CTH) R2 (np) C7 (np) R3 100k½ DO SH Note: CTH and CAGC should be optimized according to data rate and data format. (np) = component not placed. J3 CON5 Figure 11. 433.92MHz Schematic QR007-50-433 M9999-021705 12 February 17, 2005 MICRF007 Micrel Package Information 0.026 (0.65) MAX) PIN 1 0.157 (3.99) 0.150 (3.81) DIMENSIONS: INCHES (MM) 0.020 (0.51) 0.013 (0.33) 0.050 (1.27) TYP 0.064 (1.63) 0.045 (1.14) 45 0.0098 (0.249) 0.0040 (0.102) 0.197 (5.0) 0.189 (4.8) 0–8 0.010 (0.25) 0.007 (0.18) 0.050 (1.27) 0.016 (0.40) SEATING PLANE 0.244 (6.20) 0.228 (5.79) 8-Lead SOIC (M) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not� reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. February 17, 2005 13 M9999-021705