MICRF002 / 022 QwikRadiotm Low Power UHF Receiver Preliminary Information General Description The MICRF002, an enhanced version of the MICRF001 and MICRF011, is a single chip OOK (ON-OFF Keyed) Receiver IC for remote wireless applications, employing Micrel’s latest QwikRadiotm technology. This device is a true “antenna-in, data-out” monolithic device. All RF and IF tuning is accomplished automatically within the IC, which eliminates manual tuning and reduces production costs. Receiver functions are completely integrated. The result is a highly reliable yet extremely low cost solution for high volume wireless applications. Because the MICRF002 is a true single-chip radio receiver, it is extremely easy to apply, minimizing design and production costs, and improving time to market. The MICRF002 provides two fundamental modes of operation, FIXED and SWP. In FIXED mode, the device functions like a conventional superheterodyne receiver, with an (internal) local oscillator fixed at a single frequency based on an external reference crystal or clock. As with any conventional superheterodyne receiver, the transmit frequency must be accurately controlled, generally with a crystal or SAW (Surface Acoustic Wave) resonator. In SWP mode, the MICRF002 sweeps the (internal) local oscillator at rates greater than the baseband data rate. This effectively “broadens” the RF bandwidth of the receiver to a value equivalent to conventional super-regenerative receivers. Thus the MICRF002 can operate with less expensive LC transmitters without additional components or tuning, even though the receiver topology is still superheterodyne. In this mode the reference crystal can be replaced with a less expensive ± 0.5% ceramic resonator. The MICRF002 provides two feature enhancements over the MICRF001/011, (1) a Shutdown Mode, which may be used for dutycycle operation, and (2) a “Wakeup” function, which provides a logical indication of an incoming RF signal. These features make the MICRF002 ideal for low and ultra-low power applications, such as RKE and RFID. All post-detection (demodulator) data filtering is provided on the MICRF002, so no external filters need to be designed. Any one of four filter bandwidths may be selected externally by the user. Bandwidths range in binary steps, from 0.625kHz to 5kHz (SWP mode) or 1.25kHz to 10kHz (FIXED mode). The user only needs to program the appropriate filter selection based on data rate and code modulation format. Features • • • • • • • • • • • • Complete UHF receiver on a monolithic chip Frequency range 300 to 440 MHz Typical range over 200 meters with monopole antenna Data rates to 2.5kbps (SWP), 10kbps (FIXED) Automatic tuning, no manual adjustment No Filters or Inductors required Low Operating Supply Current—240 µA at 315MHz (10:1 Duty Cycle) Shutdown Mode for Duty-Cycle Operation in excess of 100:1 Wakeup Function to Enable External Decoders and Microprocessors Very low RF re-radiation at the antenna CMOS logic interface to standard decoder and microprocessor ICs Extremely low external part count Applications • • • • Automotive Remote Keyless Entry Long Range RFID Remote Fan/Light Control Garage Door/Gate Openers Typical Operating Circuit 385.5 MHz, 1200 bps OOK RECEIVER Micrel Inc. • 1849 Fortune Drive San Jose, Ca 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 944-0970 • http://www.micrel.com MICRF002 QwikRadio tm Micrel Ordering Information Part Number MICRF002BN MICRF002BM MICRF022BN MICRF022BM Temperature Range -40°C to +85°C -40°C to +85°C -40°C to +85°C -40°C to +85°C Package 16-Pin DIP 16-Pin SOIC 8-Pin DIP 8-Pin SOIC The standard 16-pin package provides the user with complete control of MICRF002 mode and filter selection. An 8-pin standard part is also available for very low cost applications. The 8-pin version comes pre-programmed in SWP mode, with Demodulator Filter bandwidth set to 5000Hz, and SHUT pin externally available. Other 8-pin configurations are available. Contact the factory for details. Pin Configuration (DIP and SOIC) July 1999 2 MICRF002 MICRF002 QwikRadio tm Micrel Pin Description (Pin numbers for the 8-pin version are identified in parentheses) Pin Number Pin Name 1 SEL0 2/3 VSSRF (1) VSS 4 (2) ANT 5 VDDRF 6 VDDBB (3) VDD 7 (4) CTH 8 9 N/C VSSBB 10 (5) 11 DO SHUT (6) 12 WAKEB 13 (7) CAGC 14 SEL1 15 (8) REFOSC 16 SWEN SEL0 1 0 1 0 Pin Function This pin, in conjunction with SEL1, programs the desired Demodulator Filter Bandwidth. This pin is internally pulled-up to VDD. See Table 1. This pin is the ground return for the RF section of the IC. The bypass capacitor connected from VDDRF to VSSRF should have the shortest possible lead length. For best performance, connect VSSRF to VSSBB at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path). This pin is the ground return for the IC. The bypass capacitor connected from VDD to VSS should have the shortest possible lead length. This is the receive RF input, internally ac-coupled. Connect this pin to the receive antenna. Input impedance is high (FET gate) with approximately 2pF of shunt (parasitic) capacitance. For applications located in high ambient noise environments, a fixed value band-pass network may be connected between the ANT pin and VSSRF to provide additional receive selectivity and input overload protection. (See “Application Note TBD”.) This pin is the positive supply input for the RF section of the IC. VDDBB and VDDRF should be connected directly at the IC pins. Connect a low ESL, low ESR decoupling capacitor from this pin to VSSRF, as short as possible. This pin is the positive supply input for the baseband section of the IC. VDDBB and VDDRF should be connected directly at the IC pins. This pin is the positive supply input for the IC. Connect a low ESL, low ESR decoupling capacitor from this pin to VSSRF, as short as possible. This capacitor extracts the (DC) average value from the demodulated waveform, which becomes the reference for the internal data slicing comparator. Treat this as a low-pass RC filter with source impedance of 118kΩ (for REFOSC frequency ft = 4.90MHz, see Note 5). A standard ± 20% X7R ceramic capacitor is generally sufficient. Unused Pin This is the ground return for the baseband section of the IC. The bypass and output capacitors connected to VSSBB should have the shortest possible lead lengths. For best performance, connect VSSRF to VSSBB at the power supply only (i.e., keep VSSBB currents from flowing through VSSRF return path). The output data signal. CMOS level compatible. A logic input for Shutdown Mode control. Pull this pin low to place the IC into operation. This pin in internally pulled-up to VDD. An output signal, active low when the IC detects an incoming RF signal, determined by monitoring for data preamble. CMOS level compatible. Integrating capacitor for on-chip AGC (Automatic Gain Control). The Decay/Attack time-constant (TC) ratio is nominally set as 10:1. Use of 0.47uF or greater is strongly recommended for best range performance. Use low-leakage type capacitors for duty-cycle operation (Dip Tantalum, Ceramic, Polyester). (See “Application Note TBD.) This pin, in conjunction with SEL0, programs the desired Demodulator Filter Bandwidth. This pin in internally pulled-up to VDD. See Table 1. This is the timing reference for on-chip tuning and alignment. Connect either a ceramic resonator or crystal (mode dependent) between this pin and VSSBB, or drive the input with an AC coupled 0.5Vpp input clock. Use ceramic resonators without integral capacitors. Note that if operating in FIXED mode, a crystal must be used; however in SWP mode, one may use either a crystal or ceramic resonator. See “Application Note TBD” for details on frequency selection and accuracy. This logic pin controls the operating mode of the MICRF002. When SWEN = HIGH, the MICRF002 is in SWP mode. When SWEN = LOW, the device operates as a conventional single-conversion superheterodyne receiver. (See “Application Note TBD” for details.) This pin is internally pulled-up to VDD. SEL1 1 1 0 0 Demodulator Bandwidth (Hz) SWP Mode 5000 2500 1250 625 FIXED Mode 10000 5000 2500 1250 Table 1 Nominal Demodulator (Baseband) Filter Bandwidth vs. SEL0, SEL1 and Mode July 1999 3 MICRF002 MICRF002 QwikRadio tm Micrel ABSOLUTE MAXIMUM RATINGS Operating Ratings Supply Voltage (VDDRF, VDDBB)..................................+7V Voltage on any I/O Pin........................VSS-0.3 to VDD+0.3 Junction Temperature..............................................+150°C Storage Temperature Range....................-65°C to + 150°C Lead Temperature (soldering, 10 seconds)..............+ 260°C Supply Voltage (VDDRF, VDDBB)..................4.75V to 5.5V Ambient Operating Temperature (TA)............-40°C to +85°C Package Thermal Resistance θJA (16 Pin DIP).........90°C/W Package Thermal Resistance θJA (16 Pin SOIC)....120°C/W This device is ESD sensitive: Meets Class 1ESD test requirements (Human body Model, HBM), in accordance with MIL-STD-883C, Method 3015. Do not operate or store near strong electrostatic fields. Use appropriate ESD precautions. Electrical Characteristics Unless otherwise stated, these specifications apply for Ta = -40°C to 85°C, 4.75<VDD<5.5V. All voltages are with respect to Ground; Positive currents flow into device pins. CAGC = 4.7µF, CTH = .047µF, VDDRF= VDDBB = VDD. REFOSC frequency = 4.90MHz. Parameter Test Conditions MIN TYP MAX UNITS Power Supply Operating Current Continuous Operation 2.4 mA Operating Current 10:1 Duty Cycle 240 µA Standby Current SHUT = VDD 0.5 µA RF/IF Section Receiver Sensitivity Note 1, 3 -103 dBm IF Center Frequency Note 4 0.86 MHz IF 3dB Bandwidth Note 3, 4 0.43 MHz RF Input Range 300 Receive Modulation Duty-Cycle 20 Maximum Receiver Input Spurious Reverse Isolation 440 MHz 80 % Rsc = 50Ω -20 dBm ANT pin, Rsc = 50Ω Note 2 30 µVrms AGC Attack / Decay ratio T(Attack) / T(Decay) 0.1 AGC Leakage Current Ta = 85°C Local Oscillator Stabilization Time To 1% of Final Value ±100 nA 2.5 msec Demod Section CTH Source Impedance Note 5 Ω 118k CTH Source Impedance Variation -15 +15 % CTH Leakage Current Ta = 85°C ±100 nA Demod Filter Bandwidth SEL0 = SEL1 = SWEN = VDD, Note 4, 6 4160 Hz Demod Filter Bandwidth SEL0 = SEL1 = VDD, SWEN = VSS Note 4, 6 8320 Hz 200k Ω 8 µA Digital/Control Section REFOSC Input Impedance Input Pull up Current SEL0, SEL1, SWEN, SHUT=VSS Input High Voltage SEL0, SEL1, SWEN Input Low Voltage SEL0, SEL1, SWEN Output Current DO, WAKEUP pins, Push-Pull Output High Voltage DO, WAKEUP pins, Iout = -1µA Output Low Voltage DO. WAKEUP pins, Iout = +1µA 0.1VDD V Output Tr, Tf DO, WAKEUP pins, Cload=15pF 10 µsec July 1999 0.8VDD 0.2VDD 4 V V 10 µA 0.9VDD V MICRF002 MICRF002 Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: July 1999 QwikRadio tm Micrel Sensitivity is defined as the average signal level measured at the input necessary to achieve 10e-2 Bit Error Rate (BER). The input signal is defined as a return-to-zero (RZ) waveform with 50% average duty cycle (e.g., Manchester Encoded Data) at a data rate of 300bps. The RF input is assumed to be matched into 50Ω. Spurious reverse isolation represents the spurious components which appear on the RF input (ANT) pin measured into 50Ω with an input RF matching network. Sensitivity, a commonly specified Receiver parameter, provides an indication of the Receiver’s input referred noise, generally input thermal noise. However, it is possible for a more sensitive receiver to exhibit range performance no better than that of a less sensitive receiver, if the “ether” noise is appreciably higher than the thermal noise. “Ether” noise refers to other interfering “noise” sources, such as FM radio stations, pagers, etc. A better indicator of achievable receiver range performance is usually given by its Selectivity, often stated as Intermediate Frequency (IF) or Radio Frequency (RF) bandwidth, depending on receiver topology. Selectivity is a measure of the rejection by the receiver of “ether” noise. More selective receivers will almost invariably provide better range. Only when the receiver selectivity is so high that most of the noise on the receiver input is actually thermal will the receiver demonstrate sensitivitylimited performance. Parameter scales linearly with REFOSC frequency ft. For any REFOSC frequency other than 4.90MHz, compute new parameter value as the ratio [(REFOSC FREQ (in MHz) / 4.90] * [Parameter Value @ 4.90MHz]. Example: For REFOSC Freq. ft = 6.00MHz, [Parameter Value @ 6.00MHz] = (6.00 / 4.90) * [Parameter Value @ 4.90MHz]. Parameter scales inversely with REFOSC frequency ft. For any REFOSC frequency other than 4.90MHz, compute new parameter value as the ratio [4.90 / (REFOSC FREQ (in MHz)] * [Parameter Value @ 4.90MHz]. Example: For REFOSC Freq. ft = 6.00MHz, [Parameter Value @ 6.00MHz] = (4.90 / 6.00) * [Parameter Value @ 4.90MHz]. Demod filter bandwidths are related in a binary manner, so any of the (lower) nominal filter values may be derived simply by dividing this parameter value by 2, 4, or 8 as desired. 5 MICRF002 MICRF002 QwikRadio tm Micrel Typical Performance Characteristics MICRF002 IDD vs Frequency (Temperature=25°°C, VDD=5.0V, SWP Mode, Continuous Operation) 6.10 5.60 5.10 4.60 4.10 IDD(mA) 3.60 3.10 2.60 2.10 1.60 250 275 300 325 350 375 400 425 450 475 500 Frequency (MHz) MICRF002 IDD vs Temperature (Frequency=315MHz, VDD=5.0V, SWP Mode, Continuous Operation) 3.30 3.10 2.90 2.70 IDD(mA) 2.50 2.30 2.10 1.90 -40 -20 0 20 40 60 85 Temperature (C) July 1999 6 MICRF002 MICRF002 QwikRadio tm Micrel MICRF002 Block Diagram July 1999 7 MICRF002 MICRF002 QwikRadio tm Micrel transmitter is used for its mechanical stability), the user may choose to configure the MICRF002 as a standard superheterodyne receiver (FIXED mode), mitigating the aforementioned problem of a competing close-in signal. This can be accomplished by tying SWEN to ground. Doing so forces the on-chip LO frequency to a fixed value. In FIXED mode, the ceramic resonator would be replaced with a crystal. Generally, however, the MICRF002 can be operated in SWP mode, using a ceramic resonator , with either LC or CRYSTAL/SAW based transmitters, without any significant range difference. Functional Description Please refer to “MICRF002 Block Diagram”. Identified in the block diagram are the four principal functional blocks of the IC, namely (1) UHF Downconverter, (2) OOK Demodulator, (3) Reference and Control, and (4) Wakeup. Also shown in the figure are two capacitors (CTH, CAGC) and one timing component (CR), usually a ceramic resonator. With the exception of a supply decoupling capacitor, these are all the external components needed with the MICRF002 to construct a complete UHF receiver. Four control inputs are shown in the block diagram, SEL0, SEL1, SWEN, and SHUT. Through these logic inputs the user can control the operating mode and selectable features of the IC. These inputs are CMOS compatible, and are pulled-up on the IC. The inputs SEL0 and SEL1 control the Demodulator filter bandwidth in four binary steps (625Hz—5000Hz in SWP, 1250Hz—10000Hz in FIXED mode), and the user must select the bandwidth appropriate to his needs. Input SWEN selects the operating mode of the IC (FIXED mode or SWP mode). When low, the IC is in FIXED mode, and functions as a conventional superheterodyne receiver. When SWEN is high, the IC is in SWP mode. In this mode, while the topology is still superheterodyne, the local oscillator (LO) is deterministically swept over a range of frequencies at rates greater than the data rate. When coupled with a peak-detecting demodulator, this technique effectively increases the RF bandwidth of the MICRF002, so the device can operate in applications where significant Transmitter/Receiver frequency misalignment may exist. th Rolloff response of the IF Filter is 5 order, while the nd demodulator data filter exhibits a 2 order response. Multiplication factor between the REFOSC frequency ft and the internal Local Oscillator (LO) is 64.5X for FIXED mode, and 64.25X for SWP mode (i.e., for ft = 6.00MHz in FIXED mode, LO frequency = 6.00MHz * 64.5 = 387MHz). Slicing Level and the CTH Capacitor Extraction of the DC value of the demodulated signal for purposes of logic-level data slicing is accomplished by external capacitor CTH and the on-chip switched-cap “resistor” RSC, indicated in the block diagram. The effective resistance of RSC is 118kohms. The value of capacitor CTH is easily calculated, once the slicing level time-constant is chosen. Slicing Level time constant values vary somewhat with decoder type, data pattern, and data rate, but typical values range 5-50msec. Optimization of the CTH value is required to maximize range, as discussed in “Application Note TBD”. [Note: The swept LO technique does not affect the IF bandwidth, so noise performance is not impacted relative to FIXED mode. In other words, the IF bandwidth is the same (500kHz) whether the device is in FIXED or SWP mode.] Due to limitations imposed by the LO sweeping process, the upper limit on data rate in SWP mode is approximately 2.5kbps. Data rates beyond 10kbps are possible in FIXED mode however. During quiet periods (i.e., no signal transmissions) the Data Output (DO pin) transitions randomly based on noise. This may present problems for some decoders. The most common solution is to introduce a small offset (“Squelch”) on the CTH pin so that noise does not trigger the internal comparator. Usually 20-30mV is sufficient, and may be introduced by connecting a several-Megohm resistor from the CTH pin to either VSS or VDD, depending on the desired offset polarity. Since the MICRF002 is an AGC’d receiver, noise at the internal comparator input is always the same, set by the AGC. So the squelch offset requirement does not change as the local “ether” noise changes from installation to installation. Note that introducing squelch will reduce range modestly, so only introduce an amount sufficient to “quiet” the output. Examples of SWP mode operation include applications which utilize low-cost LC-based transmitters, whose transmit frequency may vary up to ± 0.5% over initial tolerance, aging, and temperature. In this (patent-pending) mode, the LO frequency is varied in a prescribed fashion which results in downconversion of all signals in a band approximately 1.5% around the transmit frequency. So the Transmitter may drift up to ± 0.5% without the need to retune the Receiver, and without impacting system performance. Such performance is not achieved with currently available crystalbased superheterodyne receivers, which can operate only with SAW or crystal based transmitters. [Note: In SWP mode only, a range penalty will occur in installations where there exists a competing signal of sufficient strength in this small frequency band of 1.5% around the transmit frequency. This results from the fact that sweeping the LO indiscriminately “sweeps” all signals within the sweep range down into the IF band. This same penalty also exists with super-regenerative type receivers, as their RF bandwidth is also generally 1.5%. So any application for a super-regenerative receiver is also an application for the MICRF002 in SWP mode.] For applications where the transmit frequency is accurately set for other reasons (e.g., applications where a SAW July 1999 8 MICRF002 MICRF002 QwikRadio tm Micrel (or otherwise limited) to approximately 0.5Vpp. The specific reference frequency required is related to the system transmit frequency, and to the operating mode of the device as set by the SWEN control pin. See “Application Note TBD” for a discussion of frequency selection and accuracy requirements. AGC Function and the CAGC Capacitor The signal path has automatic gain control (AGC) to increase input dynamic range. An external capacitor, CAGC, must be connected to the CAGC pin of the device. The ratio of decay-to-attack time-constant is fixed at 10:1 (i.e., the attack time constant is 1/10th the decay time constant), and this ratio cannot be changed by the user. However, the attack time constant is selectable by the user through the value of capacitor CAGC. Wakeup Function The Wakeup function is made available for the purposes of further reducing power consumption of the overall wireless system. WAKEB is an output logic signal, which goes active when the IC detects a constant tone “header” in the demodulated output signal. Sense of the signal is activelow. This output may be used to “wakeup” other external circuits, like a data decoder or microprocessor, only at times when there is a reasonable expectation of an incoming RF signal. The Wakeup function is unavailable when the IC is in SHUT mode. [By adding resistance from the CAGC pin to VDDBB or VSSBB in parallel with the CAGC capacitor, the ratio of decay-to-attack time-constant may be varied, although the value of such adjustments must be studied on a perapplication basis. Generally the design value of 10:1 is adequate for the vast majority of applications.] See “Application Note TBD”. To maximize system range, it is important to keep the AGC control voltage ripple low, preferably under 10mVpp once the control voltage has attained its quiescent value. For this reason capacitor values ≥ 0.47uF are recommended. The Wakeup function is composed of a resettable counter, based on an internal 25kHz clock (based on a 6.4MHz reference frequency). To utilize this function, a constant tone in excess of about 4msec must be placed at the start of each data code word, or a single 4msec tone at the start of the data pattern (clearly the former is preferred to improve communication reliability). When this constant tone is detected, without interruption, for 128 clock cycles of 25kHz, WAKEB will transition low, and stay low until data begins. This particular approach is utilized over others (1) since constant tones in excess of 4msec are very rare, leading to few false-positive indications, and (2) this technique does not require the introduction of a signal path offset, which impacts achievable range. The AGC control voltage is carefully managed on-chip to allow duty-cycle operation of the MICRF002 in excess of 100:1. When the device is placed into SHUT mode (i.e., SHUT pin pulled high), the AGC capacitor is “floated”, to retain the voltage. When operation is resumed, only the voltage droop on the capacitor associated with leakage must be replenished. Thus a relatively low-leakage capacitor is recommended for duty cycle operation. The actual tolerable leakage will be application dependent. Clearly, leakage performance is less critical when the device off-time is low (milliseconds), and more critical when the off-time is high (seconds). [Note: For designers who wish to use the Wakeup function while “squelching” the output, a positive squelching offset voltage must be used. This simply requires the squelch resistor be taken to a voltage more positive than the quiescent voltage on pin CTH, so that the data output is low in absence of a transmission.] To further enhance Duty-cycle operation of the IC, the AGC push and pull currents are increased for a fixed time immediately after the device is taken out of Shutdown mode (i.e., turned-on). This compensates for AGC capacitor voltage “droop” while the IC is in Shutdown, reduces the time to reacquire the correct AGC voltage, and thus extends maximum achievable duty ratios. Push/Pull currents are increased by 45X their nominal values. The fixed time period is based on the REFOSC frequency ft, 10.9msec for ft = 6.00MHz, and varies inversely as ft varies. Shutdown Function The Shutdown function is controlled by the logic state of SHUT. When SHUT is high, the device goes into low-power standby mode, consuming less than 1µA. This pin is pulled high internally, and so must be pulled low to engage the device. Reference Oscillator (REFOSC) and External Timing Element MICRF002 Frequency and Capacitor Selection All timing and tuning operations on the MICRF002 are derived from the REFOSC function. This function is a single-pin Colpitts-type oscillator. The user may handle this pin in one of three possible ways: Selection of the REFOSC frequency ft, Slicing Level (CTH) capacitor, and AGC capacitor are briefly summarized in this section. Please see Application Note TBD for complete details. (1) connect a ceramic resonator, or (2) connect a crystal, or (3) drive this pin with an external timing signal. The third approach is attractive for further lowering system cost if an accurate reference signal exists elsewhere in the system (e.g., a reference clock from a crystal or ceramic resonator-based microprocessor). An externally applied signal should be AC-coupled, and resistively-divided down July 1999 9 MICRF002 MICRF002 QwikRadio tm Micrel 1. Selecting REFOSC Frequency ft (FIXED Mode) Assuming that a Slicing Level Timeconstant TC has been established, capacitor CTH may be computed using equation (5): As with any superheterodyne receiver, the difference between the (internal) Local Oscillator (LO) frequency flo and the incoming Transmit frequency ftx must ideally equal the IF Center frequency. Equation (1) may be used to compute the appropriate flo for a given ftx: flo = ftx ± 1.064 * (ftx / 390) CTH = TC / Rsc. 4. Selecting CAGC Capacitor in Continuous Mode (1) Selection of CAGC is dictated by minimizing the ripple on the AGC control voltage, by using a sufficiently large capacitor. It is Micrel’s experience that CAGC should be in the vicinity of 0.47µF to 4.7µF. Large capacitor values should be carefully considered, as this determines the time required for the AGC control voltage to settle from a completely discharged condition. AGC settling time from a completely discharged (0-volt) state is given approximately by equation (6): where ftx and flo are in MHz. Note that two values of flo exist for any given ftx, distinguished as “high-side mixing” and “low-side mixing”, and there is generally no preference of one over the other. After choosing one of the two acceptable values of flo, use equation (2) to compute the REFOSC frequency ft: ft = flo / 64.5. (5) (2) Here ft is in MHz. Connect a crystal of frequency ft to the REFOSC pin of the MICRF002. 4 decimal-place accuracy on the frequency is generally adequate. The following table identifies ft for some common Transmit frequencies when the MICRF002 is operated in FIXED mode. ∆T = (1.333 * CAGC) – 0.44 Transmit Freq. ftx (MHz) Generally, droop of the AGC control voltage during shutdown should be replenished as quickly as possible after the IC is “turned-on”. Recall from the section “AGC Function and the CAGC Capacitor” that for about 10msec after the IC is turned-on, the AGC push-pull currents are increased to 45X their normal values. So consideration should be given to selecting a value for CAGC and a shutdown time period such that the droop can be replenished within this 10msec period. 2. where CAGC is in microfarads, and ∆T is in seconds. 5. Selecting CAGC Capacitor in Duty-Cycle Mode REFOSC Freq. ft (MHz) 315 418 433.92 4.8970 6.4983 6.7458 Selecting REFOSC Frequency ft (SWP Mode) Selection of REFOSC frequency ft in SWP mode is much simpler than in FIXED mode, due to the LO sweeping process. Further, accuracy requirements of the frequency reference component are significantly relaxed. Polarity of the droop is unknown, meaning the AGC voltage could droop up or down. Worst-case from a recovery standpoint is downward droop, since the AGC pullup current th is 1/10 magnitude of the pulldown current. The downward droop is replenished according to the well-known equation (7): In SWP mode, ft is given by equation (3): ft = ftx / 64.25. (6) (3) I / CAGC = ∆V / ∆T Connect a ceramic resonator of frequency ft to the REFOSC pin of the MICRF002. 2-decimal place accuracy is generally adequate. (A crystal may also be used if desired, but may be necessary to reduce the Rx frequency ambiguity if the Tx frequency ambiguity is excessive. See Application Note TBD for further details.) (7) where I = AGC Pullup current for initial 10msec (67.5µA), CAGC is the AGC capacitor value, ∆T = Droop recovery time (<10msec), and ∆V is the droop voltage. For example, if user desires ∆T = 10msec, and chooses a 4.7µF CAGC, then the allowable droop is about 144mV. Using the same equation with 200nA worst case pin leakage and assuming 1uA of capacitor leakage in the same direction, the maximum allowable ∆T (Shutdown time) is about 0.56 seconds, for droop recovery in 10msec. 3. Selecting Capacitor CTH First step in the process is selection of a Data Slicing Level timeconstant. This selection is strongly dependent on system issues, like system decode response time and data code structure (e.g., existence of data preamble, etc.). This issue is too broad to discuss here, and the interested reader should consult the Application Note 22. Source impedance of the CTH pin is given by equation (4), where ft is in MHz: Rsc = 118kΩ * (4.90 / ft). July 1999 (4) 10 MICRF002 MICRF002 QwikRadio tm Micrel I/O Pin Interface Circuitry 3. CAGC Pin Interface circuitry for the various I/O pins of the MICRF002 is shown in Figures 1 through 6. Specific information regarding each of these circuits is discussed in the following sub-paragraphs. Not shown are ESD protection diodes which are applied to all input and output pins. Figure 3 illustrates the CAGC pin interface circuit. The AGC control voltage is developed as an integrated current into a capacitor CAGC. The attack current is nominally 15µA, while the decay current is a 1/10th scaling of this, nominally 1.5µA, so the attack/decay timeconstant ratio is fixed at 10:1. Signal gain of the RF/IF strip inside the IC diminishes as the voltage on CAGC decreases. Further discussion on setting the attack time constant is found in “Application Note TBD. Modification of the attack/decay ratio is possible by adding resistance from CAGC pin either to VDDBB or VSSBB, as desired. 1. ANT Pin Both the Push and Pull current sources are disabled during SHUT, which holds the voltage across CAGC, and improves recovery time in duty-cycled applications. To further improve duty cycle recovery, both Push and Pull currents are increased by 45X for approximately 10msec after release of SHUT. This allows rapid recovery of any voltage droop on CAGC while in SHUT. 4. DO and WAKEB Output Pins Figure 1 ANT Pin The output stage for the signals DO and WAKEB is shown in Figure 4. The output is a 10µA push-10µA pull, switched current stage. Such an output stage is capable of driving CMOS-type loads. An external buffer-driver is recommended for driving high capacitance loads. The ANT pin is internally AC-coupled via a 3pF capacitor, to an RF N-channel MOSFET, as shown in Figure 1. Impedance on this pin to VSS is quite high at low frequencies, and decreases as frequency increases. In the UHF frequency range, the device input can be modeled as 6.3kΩ in parallel with 2pF (pin capacitance) shunt to VSSRF. 5. REFOSC Pin The REFOSC input circuit is shown in Figure 5. Input impedance is quite high (200kΩ). This is a Colpitts oscillator, with internal 30pF capacitors. This input is intended to work with standard ceramic resonators, connected from this pin to VSSBB, although a crystal may be used instead, where greater frequency accuracy is required. The resonators should not contain integral capacitors, since these capacitors are contained inside the IC. Externally applied signals should be AC-coupled, amplitude limited to approximately 0.5Vpp. The nominal DC bias voltage on this pin is 1.4V. 2. CTH Pin Figure 2 illustrates the CTH pin interface circuit. CTH pin is driven from a P-channel MOSFET source-follower biased with approximately 10µA of bias current. Transmission gates TG1 and TG2 isolate the 6.9pF capacitor. Internal control signals PHI1/PHI2 are related in a manner such that the impedance across the transmission gates looks like a “resistance” of approximately 100kΩ. The DC potential on the CTH pin is approximately 1.6V 6. Control Inputs (SEL0, SEL1, SWEN, SHUT) Control input circuitry is shown in Figures 6a and 6b. The standard input is a logic inverter constructed with minimum geometry MOSFETs (Q2, Q3). P-channel MOSFET Q1 is a large channel length device which functions essentially as a “weak” pullup to VDDBB. Typical pullup current is 5µA, leading to an impedance to the VDDBB supply of typically 1MΩ. July 1999 11 MICRF002 MICRF002 QwikRadio tm Micrel Figure 3 CAGC Pin Figure 2 CTH Pin Figure 5 REFOSC Pin Figure 4 DO and WAKEB Pins Figure 6b SHUT Figure 6a SEL0, SEL1, SWEN July 1999 12 MICRF002 MICRF002 QwikRadio tm Micrel Typical Application Figure 7 below illustrates a typical application for the MICRF002 UHF Receiver IC. Operation in this example is at 385.5MHz, and may be customized by selection of the appropriate reference frequency (CR1), and adjustment of the antenna length. The value of C4 would also change, if the optional input filter is used. Changes from the 1kbps data rate may require a change in the value of R1. The Bill of Materials is shown in the accompanying chart. Figure 7 385.5MHz, 1kbps OOK Receiver/Decoder SWP Mode, Continuous Operation 6-Bit Address Decode/2 OP Codes Bill of Materials Item U1 U2 CR1 D1 R1 R2 C1 C3 C2 C4 Part Number MICRF002 HT-12D CSA6.00MG SSF-LX100LID Manufacturer Micrel Holtek Murata Lumex Bourns Bourns Panasonic Panasonic Panasonic Panasonic Vendor Bourns Holtek Lumex Murata Panasonic Description UHF Receiver Logic decoder 6.00MHz Cer. Res. Red LED 68k, 1/4W ,5% 1k,1/4W, 5% 4.7µF, Dip Tant. Cap 0.47µF, Dip Tant. Cap 2.2µF, Dip Tant. Cap 8.2pF, COG Cer. Cap Telephone (909) 781-5500 (408) 894-9046 (800) 278-5666 (800) 241-6574 (201) 348-7000 Fax (909) 781-5273 (408) 894-0838 (847) 359-8904 (770) 436-3030 (201) 348-8164 MICREL INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB http://www.micrel.com This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. This is preliminary information and a final specification has not been completed. Before making any final design determination, consult with Micrel for final specifications. ©1998 Micrel Incorporated July 1999 13 MICRF002