DATA SHEET Internet of Things Smart meters TX_IN PA_OUT Applications In-home appliances CPS CTX CSD ANT_SEL SE2435L: 860 to 930 MHz High-Power RF Front-End Module Logic Control Smart thermostats PA_IN Industrial applications PA Tx_FLT Features ANT1 TR Integrated PA with +30 dBm output power ANT2 Integrated LNA with programmable bypass LNA Integrated antenna switching with transmit/receive diversity function Low FEM noise figure of 2 dB, typical Single-ended 50 transmit/receive RF interface Fast turn-on/turn-off time: < 1 μsec Supply voltage: 2.0 to 4.8 V Rx_FLT LNA_IN Y1464 Figure 1. SE2435L Block Diagram Sleep mode current: < 1 μA QFN (24-pin, 4 x 4 x 0.9 mm ) NiPdAu plated package (MSL1, 260 C per JEDEC J-STD-020) The SE2435L is designed for ease of use and maximum flexibility with fully matched 50 TX and RX inputs and antenna outputs, and digital controls compatible with 1.6 to 3.6 V CMOS levels. 2 17 N/C CPS 3 16 TX_IN CTX 4 15 N/C TX_FLT 5 14 ANT1 TR 6 13 N/C The SE2435L is packaged in a 24-pin, 4 x 4 mm Quad Flat NoLead (QFN) package. A functional block diagram of the SE2435L is provided in Figure 1. Figure 2 shows the pinout for the SE2435L. Table 1 lists the pin assignments and signal descriptions. ANT2 12 PA_IN RX_FLT 1 1 N/C N/C 1 0 18 LNA_IN 9 1 GND 8 CSD ANT_SEL 7 The SE2435L is a high-performance, highly integrated RF front-end module designed for high-power Industrial, Scientific, Medical (ISM) band applications operating in the 860 to 930 MHz frequency range. The RF blocks operate over a wide supply voltage range from 2.0 to 4.8 V allowing the SE2435L to be used in battery powered applications over a wide spectrum of the battery discharge curve. 19 N/C 20 PA_OUT 21 VCC2 22 N/C 23 VCC0 24 VCC1 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Description Y0083 Figure 2. SE2435L Pinout – 24-Pin QFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 1 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 1. SE2435L Signal Descriptions Pin Name Description Pin Name Description 1 CSD Shutdown control input 14 ANT1 Antenna port 1 2 PA_IN PA input (from Tx filter) 15 N/C Not connected internally to the device 3 CPS Rx path select control input 16 TX_IN Tx signal to antennas (from OMN) 4 CTX Transmit enable control input 17 N/C Not connected internally to the device 5 TX_FLT Transmit signal (to Tx filter) 18 N/C Not connected internally to the device 6 TR Bi-directional RF signal to/from transceiver 19 N/C Not connected internally to the device 7 ANT_SEL Antenna select control input 20 PA_OUT PA output (to Z optimum) (Note 1) 8 GND Ground 21 VCC2 Positive power supply 9 LNA_IN LNA input (from Rx filter) 22 N/C Not connected internally to the device 10 N/C Not connected internally to the device 23 VCC0 Positive power supply 11 RX_FLT Rx signal from antennas (to Rx filter) 24 VCC1 Positive power supply Paddle GND Exposed die paddle; electrical and thermal ground. Connect to PCB ground 12 ANT2 Antenna port 2 13 N/C Not connected internally to the device Note 1: Z optimum = 5 Ω for +30 dBm or 8 Ω for +27 dBm POUT. Electrical and Mechanical Specifications specifications are provided in Tables 4 through 9. Typical performance characteristics are shown in Figures 3 through 8. Table 2 provides the absolute maximum ratings, and Table 3 shows the recommended operating conditions.Electrical Table 2. SE2435L Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Supply voltage (no RF) VCC –0.3 5.5 V Operating temperature TA –40 85 °C Storage temperature TSTG –40 125 °C Tx input power at TR port PIN_TX_MAX +10 dBm Rx input power at ANT1 or ANT2 ports PIN_RX_MAX +10 dBm Electrostatic discharge: ESD 1000 V Human Body Model (HBM), Class 1C Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 3. SE2435L Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage on VCC VCC 2.0 4.0 4.8 V Ambient temperature TA –40 +25 +85 °C Table 4. SE2435L DC Electrical Specifications (Note 1) (VCC = 4.0 V, f = 915 MHz, TA = +25 C, Unless Otherwise Noted) Parameter Total supply current, transmit mode Symbol ICC_TX30 ICC_TX27 ICC_TX24 Test Condition Min POUT = +30 dBm POUT = +27 dBm POUT = +24 dBm Typical Max Units 550 380 275 mA mA mA 6 mA Total supply current, receive mode ICC_RX Total supply current, receive bypass mode ICC_RXB Quiescent current ICQ_TX No RF 50 Sleep supply current ICC_OFF No RF 0.05 μA 280 mA μA 1.00 Note 1: Performance is guaranteed only under the conditions listed in this table. Table 5. SE2435L Electrical Specifications: Control Logic Characteristics (Note 1) (TA = +25 C, Unless Otherwise Noted) Parameter Symbol Control voltage: High Low VIH VIL Input current: High Low IIH IIL Test Condition Min Typical 1.6 0 Max Units Vcc (Note 2) 0.3 V V 1 1 μA μA Note 1: Performance is guaranteed only under the conditions listed in this table. Note 2: For Pin 7, ANT_SEL, the maximum is 3.6 V. Table 6. SE2435L Electrical Specifications: Mode Control Logic (TA = +25) Mode CPS CSD CTX ANT_SEL Sleep (all off) 0 0 0 X Receive or transmit bypass 0 1 0 X Receive LNA mode 1 1 0 X Transmit X 1 1 X ANT1 port enabled X X X 0 ANT2 port enabled X X X 1 Note 1: “1” = 1.6 to Vcc, “0” = 0 to 0.3 V, “X” = don’t care. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 3 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 7. SE2435L Electrical Specifications: AC Transmit Mode (VCC = 4 V, TA = +25 C, All Unused Ports Terminated at 50 , Unless Otherwise Noted. Input Port TR, Output Ports ANT1 and ANT2 Lumped Elements Filter Connected between the TX_FLT and PA_IN Pins) Parameter Symbol Test Condition Min Typical Units 930 MHz f Output power at ANT1 or ANT2 ports in the 900 to 930 MHz frequency range (Note 1) POUT_915 VCC = 4.8 V VCC = 4.0 V VCC = 3.6 V VCC = 3.0 V +31.5 +30.5 +29.5 +28.0 dBm dBm dBm dBm Output power at ANT1 or ANT2 ports in the 860 to 870 MHz frequency range (Note 2) POUT_860 VCC = 4.0 V VCC = 3.6 V VCC = 3.0 V VCC = 2.0 V +27 +24 +21 +18 dBm dBm dBm dBm PA power added efficiency PAE_PA POUT = +28 dBm at PA_OUT port, 915 MHz Small signal gain (Note 1) S21_915 900 to 930 MHz 26 dB Small signal gain (Note 2) S21_860 860 to 870 MHz 26 dB Small signal gain variation (Notes 1 and 2) S21 Gain variation across frequency range Output return loss (Notes 1 and 2) nd 2 harmonic (Notes 1 and 3) S22ANT1,2 860 Max Frequency range 64 Into 50 , ANT1 and ANT2 ports –10 % 2 dBp-p –6 dB 2fo POUT = +30 dBm –22 dBc 3 to 10 harmonic (Notes 1 and 3) 3fo to 10fo POUT = +30 dBm –72 dBc Turn-on time (Note 4) tON 1 μs Turn-off time tOFF 1 μs Stability STAB rd th Ruggedness RU CW, PIN = 0 dBm 0.1 GHz to 20 GHz load VSWR = 6:1 All non-harmonically related outputs less than –43 dBm CW, POUT = +30 dBm into 50 Ω, load VSWR = 10:1 No permanent damage Note 1: 900 to 930 MHz with specified matching network on the Evaluation Board. Note 2: 860 to 870 MHz with specified matching network on the Evaluation Board. Note 3: Measured with continuous wave signal. Note 4: From 50% of CTX edge to 90% of final RF output power. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 8. SE2435L Electrical Specifications: AC Receive Mode (VCC = 4 V, TA = +25 C, f = 900 to 930 MHz and 860 to 870 MHz, All Unused Ports Terminated at 50 Ω, Unless Otherwise Noted. Input Port ANT1 or ANT2, Output Port TR. 0 Ω Connected between the RX_FLT and LNA_IN Pins in lieu of External Filters) Parameter Symbol Test Condition Min Frequency range fIN 860 Receive gain RX_GAIN 14 Typical Max Units 930 MHz 16 18 dB 2 2.5 Receive noise figure NF Input third order intercept IIP3 –5 –2 dBm Input 1-dB compression point IP1dB –15 –12 dBm Antenna port return loss S11ANT1,2 Into 50 , ANT1 and ANT2 ports –12 dB –8 dB Turn-on time (Note 1) tON 1 μs Turn-off time (Note 2) tOFF 1 μs Gain in bypass mode G_bp –3 Input 1-dB compression point in bypass mode IP1dB +10 –2 dB dBm Note 1: From 50% of CTX edge to 90% of final RF output power. Note 2: From 50% of CTX edge to 10% of final RF output power. Table 9. SE2435L DC Electrical Specifications: Diversity Antenna Function (VCC = 4 V, TA = +25 C, f = 900 to 930 MHz and 860 to 870 MHz, All Unused Ports Terminated at 50 , Unless Otherwise Noted) Parameter Symbol Min Typical Max Units Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB Insertion loss from TX_IN to ANT1 TX_ANT1 0.8 dB Insertion loss from TX_IN to ANT2 TX_ANT2 0.8 dB Insertion loss from ANT1 to RX_FLT RX_ANT1 0.6 dB Insertion loss from ANT2 to RX_FLT RX_ANT2 0.6 dB Insertion loss from TR to TX_FLT TxRx_Tx 0.5 dB ANT1 to ANT2 switching time transmit mode TANT1-ANT1_TX 800 ns ANT1 to ANT2 switching time receive mode TANT1-ANT2_RX 400 ns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 5 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Typical Performance Characteristics (Note 1) –20 –30 900 MHz –40 915 MHz 930 MHz POUT (dBm) –60 –70 –80 –90 –100 650 +30 550 +25 450 +20 350 +15 250 Pout [dBm] +10 ts205 –110 –120 #2 #3 #4 #5 #6 #7 #8 #9 +5 –22 –20 –18 –16 –14 –12 –10 –8 #10 # Harmonics 650 32 550 –2 0 ICC (mA) 26 Y1472 350 250 24 900 MHz 915 MHz 930 MHz 22 +12 +14 +16 900 MHz 915 MHz 930 MHz 150 +18 +20 +22 +24 +26 +28 +30 50 +10 +32 +12 +14 +16 +18 +20 +22 +24 +26 +28 +30 +32 Output Power (dBm) Output Power (dBm) Figure 6. Typical ICC vs POUT (VCC = 4 V) Figure 5. Typical Gain vs POUT (VCC = 4 V) 55 34 32 50 PAE (%) 30 28 2.0 V 3.3 V 3.6 V 4.0 V 22 +14 45 40 35 Y1475 4.8 V +12 2.0 V 3.3 V 3.6 V 4.0 V 4.8 V +16 +18 +20 +22 +24 +26 Output Power (dBm) Figure 7. Typical Gain vs POUT (VCC = 2.0 to 4.8 V) +28 +30 +32 +34 ts272 26 24 30 +20 +21 +22 +23 +24 +25 +26 +27 +28 +29 +30 +31 +32 +33 +34 Output Power (dBm) Figure 8. Typical PAE vs POUT & VCC, CW (VCC = 2.0 to 4.8 V) (including OMN and Antenna Filter Losses) Note 1: Typical performances graphs at 868 MHz are available upon request (+24, +27, and +30 dBm POUT). Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 +2 +4 +6 450 28 ts276 Gain (dB) 30 Gain (dB) –4 Figure 4. Typical POUT and ICC Transfer Characteristics 34 20 +10 50 –6 Input Power (dBm) Figure 3. Typical Harmonics Level at +30 dBm POUT (including Antenna Filter) 20 +10 150 ICC [mA] Y1474 Level (dBc) –50 +35 ICC (mA) (VCC = 4 V, TA = +25 C, f = 900 to 930 MHz, All Unused Ports Terminated at 50 , Unless Otherwise Noted) July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Evaluation Board Description The SE2435L-EK1 Evaluation is to demonstrate the performance of the SE2435L Front-End Module. It is optimized for evaluation, experimentation and investigation, using CW (continuous wave) signals. Figure 9 shows the Evaluation Board. The Evaluation Board schematic diagram is provided in Figure 10. The Bill of Materials (BOM) for the SE2435L Evaluation Board is listed in Table 10. ts037 Figure 9. SE2435L Evaluation Board Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 7 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE J4 C6 4.7 µF C1 10 nF C11 1 nF C8 33 pF × L2 1.3 nH CTX 4 CTX TX_FLT 6 TR SMA 7 ANT_SEL 8 N/C PA_OUT N/C VCC2 VCC0 9 7 10 9 12 11 14 13 16 15 18 17 20 19 19 N/C U1 SE2435L 5 5 8 ANT_SEL C3 8.2pF 10 TX_IN 11 18 17 × × L1 3.0 nH N/C 15 ANT1 14 N/C 13 12 × C17 1.8 pF C9 3.3 pF 16 × L6 6.8 nH L8 6.8 nH J3 SMA × C12 3.3 pF ANT2 CPS RX_FLT 3 N/C J1 20 PA_IN CPS 3 6 × 21 N/C LNA_IN R1 3.3 pF 22 CSD GND 2 23 VCC1 PAD 1 ANT_SEL CSD 24 4 CSD C2 22 pF 25 1 VDD CPS L5 6.8 nH C10 100 pF 2 CTX L3 4.7 nH L4 3.3 nH VCC L9 6.8 nH L7 6.8 nH J2 SMA C13 3.3 pF Note: Discard N/C pins that are connected to ground on the Evaluation Board. Figure 10. Evaluation Board Schematic for 915 MHz Application and FCC Conducted Harmonics Rejection Compliant Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H ts038 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 10. SE2435L Evaluation Board Bill of Materials (Note 1) Component Part Number Description Value Package Manufacturer L2 LQG15HN1N3S02D High frequency multilayer 1.3 nH 0402 Murata C17 GRM1555C1H1R8CZ01 Multilayer ceramic 1.8 pF 0402 Murata C11 GRM155R71H102KA01 Multilayer ceramic 1 nF 0402 Murata L1 LQG15HN3N0S02D High frequency multilayer 3.0 nH 0402 Murata L4 LQG15HN3N3S02D High frequency multilayer 3.3 nH 0402 Murata L3 LQG15HN4N7S02D High frequency multilayer 4.7 F 0402 Murata C6 GRM188R60J475KE19 Multilayer ceramic 4.7 F 0603 Murata C3 GRM1555C1H8R2DZ01 Multilayer ceramic 8.2 pF 0402 Murata C1 GRM155R71E103KA01 Multilayer ceramic 10 nF 0402 Murata J4 TSW-110-07-G-D 100 mil Header 10X2 100 mil Samtec C2 GRM1555C1H220JZ01 Multilayer ceramic 22 pF 0402 Murata C8 GRM1555C1H330JZ01 Multilayer ceramic 33 pF 0402 Murata C10 GRM1555C1H101JZ01 Multilayer ceramic 100 pF 0402 Murata U1 SE2435L 860 to 930 MHz high power RF FEM SE2435L QFN400x400 Skyworks J1, J2, J3 142-0701-851 SMA end launch straight jack receptacle – tab contact SMA End launch Johnson Components C9, C12, C13, R1 GRM1555C1H3R3CZ01 Multilayer ceramic 3.3 pF 0402 Murata L5, L6 ,L7, L8, L9 LQG18HN6N8S00D High frequency multilayer 6.8 nH 0603 Murata Note 1: Schematic and BOM has been designed to optimize performance with CW signals, 100% duty cycle. Evaluation Board Setup Procedure This section provides the details required to setup the evaluation board and the test equipment for the SE2435L. Table 11 describes the pins on the Power and Control I/O Header J4. Note that it is recommended to use proper engineering connection practices by making RF and digital connections prior to turning on the power supply. Connect Supply 1. Connect (J1, J2, and J3) to 50 instruments. Terminate all unused ports (if applicable) with 50 . 2. Connect the supply ground to Pin 1 of J4. 3. Connect 3.6 V or 4.0 V to Pin 2 of J4: The required RF path/antenna can be selected using the information in Table 6. Measure Performance TX: The 860 to 930 MHz (depending on the region) amplifier performance can be monitored by applying an RF signal to connector J1 (TR), and monitoring the output power on connector J2 (ANT2) or J3 (ANT1). RX: The 860 to 930 MHz LNA performance can be monitored by applying an RF signal to connector J2 (ANT2) or J3 (ANT1), and monitoring the output signal on connector J1 (TR). CAUTION Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device. A starting input power of –20 dBm is suitable for the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 9 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Table 11. Power and Control I/O Header (J4) Evaluation Board Label Pin Number Description Recommended setting GND 1,3,5,7,9,11,13,15,17,19 Ground General purpose grounds VCC 2,4,6,10,14,18 Supply voltage General purpose VCC provided as the main power supply. CTX 8 Control CPS 12 Control CSD 16 Control ANTSEL 20 Control Package Dimensions The layout footprint for the SE2435L is provided in Figure 11. Typical part markings are shown in Figure 12. Package dimensions for the SE2435L are shown in Figure 13, and tape and reel dimensions are provided in Figure 14. Package and Handling Information Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur See Table 6. when the part is subjected to high temperature during solder assembly. The SE2435L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H 5X 1.02 5X 0.51 5X 0.0 5X 1.02 4.40 2.70 5X 0.51 DATA SHEET • SE2435L: 860 TO 930 MHZ HIGH-POWER RF FRONT-END MODULE 5X 1.02 5X 0.51 2.70 5X 0.0 0 5X 0.51 4.40 5X 1.02 0.60 Typ 25X Ø0.254 0 0.25 Typ 0.500 Typ Board Metal Via Pattern (Note 4) 4.50 2.50 4.40 1.00 Typ 0.20 Typ 1.00 Typ 2.50 4.40 0.20 Typ 4.50 0.60 Typ 0.70 Typ 0.35 Typ 4 x 4 QFN Package Outline 0.500 Typ 0.25 Typ Solder Mask Pattern (Note 6) Notes: 0.500 Typ Stencil Pattern (Note 5) 64% Solder Coverage on Center Pad 1. 2. 3. 4. All dimensions are in millimeters. Interpret dimensions and tolerances per ASME Y14.5M-1994. Unless specified, dimensions are symmetrical about center lines. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), solder mask on the far side should tent or plug via holes. 5. Stencil recommendations: 0.125 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer the best paste release. 6. Solder mask recommendations: Contact board fabricator for recommended solder mask offset and tolerance. Y1538 Figure 11. SE2435L Recommended Footprint (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 11 November 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412G DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Pin 1 Designator e4 SiGe 2435L XXXX Part Number Lot Code Figure 12. Typical Part Markings (Top View) 4.00 ±0.05 A 2.70 ±0.05 0.85 ±0.05 0.05 C 0.203 Ref 0.30 X 45° B 0.000-0.005 Pin 1 Indicator Pin 1 Indicator Exposed Pad 2.70 ±0.05 4.00 ±0.05 0.500 R0.075 Typ 24X 0.20 Min 2X 0.05 C 0.08 C 25X Top View Side View NOTES: 1. All measurements are in millimeters, unless otherwise specified. 2. Dimensions and tolerances according to ASME Y14.5M-2009. 3. Unless otherwise specified the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ±0.5° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 4. Coplanarity applies to the exposed center ground pad as well as the terminals. 5. Dimension applies to the metallized terminal. If the terminal has a radius, the dimension should not be measured in that radius area. 6. Plating requirements per source control drawing (SCD) 2504. 7. Unless specified, dimensions are symmetrical about center lines. See Detail B See Detail A 4 C 0.05 C Bottom View Seating Plane 2X 0.093 ±0.05 2X R0.075 0.40 ±0.05 0.25 ±0.05 5 R0.075 Detail A Detail B Scale 2X (16 Places) Scale 2X (8 Places) 0.10 0.05 C A B C 0.307 ±0.05 0.25 ±0.05 5 Figure 13. SE2435L Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H 0.10 0.05 0.40 ±0.05 C A B C Y2166 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE 8.0 ±0.1 D 1.50 +0.10 4.0 Note 1 1.75 ±0.1 2.0 ±0.05 1.22 ±0.1 0.254 ±0.013 5.5 ±0.05 12.0 ±0.3 4.35 ±0.1 4.35 ±0.1 Pin 1 Indicator Notes: 1. 10-Sprocket hole pitch cumulative tolerance ±0.2. 2. Camber in compliance with EIA-481. Y0086 Figure 14. SE2435L Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202412H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 7, 2015 13 DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE Ordering Information Model Name SE2435L-S SE2435L-R Manufacturing Part Number SE2435L Evaluation Board Part Number SE2435L -EK1 Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 July 7, 2015 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412H