● ● ● ● ● ● ● ● ● ● Features LED DRIVER 30W Class II AC-DC LED Power Supply 500mA or 700mA Constant Current Drives 3 - 15 High brightness LEDs Active Power Factor Correction >0.95 Fused Input, Protected Output 3kVAC Isolation UL-8750 Certified Output Connector to avoid miswiring Low Cost Long 5 Year Warranty Description A compact 30W constant current switching power module suitable for driving up to 15 high power LEDs (Vf = 3.6V). The output current is fixed at 500mA or 700mA. Active power factor correction is standard. This series features both screw terminal and socket output connections. The socket connecter avoids the possibility of miswiring and damaging the LED load if the LEDs are preassembled into a wiring harness or lamp fitting. LIGHTLINE AC/DC-Converter with 5 year Warranty 30 Watt PFC Single Output Selection Guide Part Number Input Voltage Range (VAC) Input Current at full load (mA) Output Output Voltage Range Current (VDC) (mA) Max # LEDs RACD30-500 universal 390 10-56 500 15 x 2W RACD30-700 universal 390 10-43 700 12 x 3W, 12+12 x 1W Specifications (typical at 25°C and after warm up time unless otherwise specified ) Input Voltage Range Standard 90-264VAC Rated Power 30 Watts max. Input Frequency Range 47-63 Hz Power Factor Full Load, 115VAC/230VAC 0.9 THD Full Load, 115VAC 13% max. Full Load, 230VAC 11% max. Open Circuit Voltage 500mA Version 58VDC (Zener Clamp) 700mA Version 48VDC Inrush Current (<2mS) 115VAC/230VAC 230VAC, Full Load 390mA typ. Leakage Current Input Fuse 115VAC/240VAC - 60/50Hz Standard 0.5mA typ. T1A (combined Tolerance, load Regulation and Line Regulation) ±10% Open Circuit Protected 3 LEDs Minimum Load Hold Up Time 40 - 100 kHz typ. Efficiency at Full Load 85% RMS Isolation Voltage (input to output) 3kVAC / 1 minute Temperature Coefficient ±0.02%/°C typ. Overload Protection Overtemperature Protection Operating Temperature Range (free air convection) Storage Temperature Range Weight Packing Quantity L-42 RACD30 18ms min. Operating Frequency Short Circuit Protection Output Overvoltage Protection E340696 UL-8750 Certified EN 61347 Certified 10A max. Input Current Output Current Accuracy RoHS 2011/65/EU 6/6 120% typ. 500mA Version 700mA Version Continuous Current Limit 56V Zener Diode Clamp 43V Zener Diode Clamp Shutdown, Automatic restart after cooling down Ambient Temperature -20°C to +50°C Case Temp. 85°C max. (500mA version: 90°C max.) -40°C to +100°C 200g 1pcs continued on next page REV: 0/2015 Refer to Application Notes www.recom-power.com RACD30 Series LIGHTLINE AC/DC-Converter Specifications (typical at 25°C and after warm up time unless otherwise specified ) Humidity IP Rating PCB Material Case Material Designed to meet Standards 95% RH max. IP20, Indoor Use Only Plastic Resin with Fibreglass (UL94V-0) Plastic Electrical Lighting, EMC Emissions EN55015:2006 + A1: 2007 + A2:2009 Limits for Harmonics Emissions EN 61000-3-2:2006 EMC Compatability: Flicker and Voltage Variations EN 61000-3-3:2006 Electrical Lighting: EMC Immunity EN 61547:1995 + A1:2000 Class II Power Supply Safety UL1310 FCC FCC18A <20% LED Lighting Safety UL8750 SEMKO CE Certification, General Safety EN 61347-1: 2008 SEMKO CE Certification, Safety of AC supplied Control Gear for LED Modules EN 61347-2-13: 2006 25°C ambient >70 x 10³ hours in operation AC Input Screw terminal LED Output Screw Terminal LED Output 5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar) THD Certifications Design Lifetime Connections Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Characteristic Maximum Number of LED drivers per circuit breakers Circuit Breaker 115VAC, 1Ohm 90° phase angle 230VAC, 1Ohm 90° phase angle 277VAC, 1Ohm 90° phase angle Circuit Breaker Current Typ 10A 16A 20A 25A C 32 48 57 72 B 24 38 46 58 C 38 62 74 92 B 28 44 53 66 C 44 71 84 106 RACD30 Condition Package Style and Pinning Connections 160 5.5mm socket x 2.1mm 50 42 Tc 8 3.5mm dia. 15 45 Cable entry with strain relief CN1 Function L VAC in (L) N VAC in (N) CN2 Function + LED+ - LED- 5.5mm Socket Function 152 22 2 Mounting screws are included Tc=Case Temperature Measuring Point Pin LED+ Shell LED- Tolerance XX =+/-1mm XX.X =+/-0.5mm The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV: 0/2015 L-43