PRODUCT DATASHEET ET-9RS REAL-TIME-RING™ ETHERNET SWITCH WITH 9 PORTS The ET-9RS is a 9 port industrial Ethernet switch featuring Sixnet’s Real-Time-Ring™ which provides very fast, faulttolerant network redundancy and prioritized message delivery needed in critical real-time systems. These Rings self-configure and just run, without the complex configuration steps required by alternative solutions. This advanced technology delivers reliability and performance, saves you money, and makes your job easier. PRODUCT HIGHLIGHTS 9 ports with up to two fiber optic ports Super-fast, fault tolerant ring redundancy Pre-configured for true plug and play simplicity Truly rugged design with -40 to 85°C operation Dual power with MIL-STD-1275 protection REAL-TIME FAULT-TOLERANT RINGS Recovery time of 30 mS plus 5 mS per hop! Ideal for deterministic systems and PLCs Real-time Modbus over Ethernet monitoring IDEAL FOR Real-time control Distributed systems Outdoor / marine use REAL-TIME TRAFFIC PRIORITIZATION Assure delivery of real-time data Improve network utilization User settable priority assignments MANAGED SWITCH FEATURES User configurable port settings Port mirroring for traffic diagnostics Message filtering to prevent broadcast storms TROUBLE FREE OPERATION Firmware upgrades are FREE forever Ultra-reliable 1,000,000 hours MTBF Firmware upgrades are FREE forever -40 to +85 °C operating range UL / CSA (CUL), CE, and Hazloc (zone 2) rated SOLUTIONS FOR YOUR INDUSTRIAL NETWORKING CHALLENGES WWW.SIXNET.COM REAL-TIME-RING™ ETHERNET SWITCH WITH 9 PORTS SPECIFICATIONS ETHERNET PERFORMANCE 9 Ethernet ports total Ethernet switch type Intelligent store & forward Ethernet protocols supported all IEEE 802.3 RJ45 ports (shielded) 10/100BaseTX RJ45 speed (10 or 100 Mbps) auto-negotiation RJ45 MDI/MDIX auto-crossover RJ45 TD and RD auto-polarity Fiber optic port speed 100BaseFX (100 Mbps) Fiber optic port wavelength 1300 nm center typical Fiber multimode (mm) 50- 62.5/125 um (SC or ST connector) Fiber singlemode (sm) 9-10 9/125 um (SC or ST connector) Fiber max. distance (full duplex) 4 km (mm), 20 or 40 km (sm) or more (contact Sixnet) Typical latency for 10 Mbps ports 16 us + frame time; typical latency for 100 Mbps ports 5 us + frame time; varies on load and settings Full or half duplex operation configurable MAC addresses supported 2048 Memory bandwidth 3.2 Gbps Ethernet isolation 1500 VRMS 1 minute REAL-TIME-RING™ FEATURES Maximum switches in ring: 50+ Dual ring support Link loss recovery time: 30mS + 5mS/hop ETHERNET COMPLIANCE IEEE 802.3z (Gigabit 1000 Mbps Ethernet connections) IEEE 802.3u (Fast Ethernet 100 Mbps for newer devices) IEEE 802.3 (10 Mbps Ethernet supports legacy devices) IEEE 802.3x (Full-Duplex with Flow Control) IEEE 802.1p (QoS / CoS – Quality & Class of Service) ET-9RS STATUS REPORTING Modbus Ethernet over UDP “OK” contact output up to 0.5 Amp POWER INPUT Power input redundant input terminals Input power (typical - all ports active at 100 Mbps) o 6.0 W (model -1 without fiber) o 7.0 W (model -2 & -3 w/ 1 fiber) o 8.0 W (models -4 & -5 w/ 2 fiber) Power Input 10-50 VDC (derate 1.8°C / V above 30V) MIL-STD-1275 power protection standard Military surge protection 100 volts for 1 second Transient protection 15,000 watts peak Spike Protection 5,000 watts (10x for 10 uS) or 250 volts (50x for 100 uS) ENVIRONMENTAL Operating temperature range -40 to +85 °C Storage temperature range -40 to +85 °C Humidity (non-condensing) 5 to 95% RH Vibration IEC60068-2-6 STANDARDS COMPLIANCE Electrical safety - UL508/CSA C22.2/14; EN61010-1, CE EMI emissions - FCC part 15, ICES-003; EN61000-6-4, CE EMC - immunity EN61000-6-2, CE Hazardous locations: UL1604/CSA C22.2/213 (Class I, Div. 2); EN60079-15 (Zone 2, Category 3), CE (ATEX) Eye safety (fiber models) IEC60825-1, Class 1; FDA 21 CFR 1040.10 and 1040.11 PHYSICAL DIN rail or direct panel mounting Case (UL 94V-0 Lexan and rust-free aluminum case) with IP30 protection Dimensions see mechanical drawing All specifications are subject to change. Consult factory for latest info. ORDERING GUIDE ET-9RS-1-E1 ET-9RS-2SC-E1 ET-9RS-2ST-E1 ET-9RS-3SC-E1 ET-9RS-3ST-E1 ET-9RS-3SCL-E1 ET-9RS-3STL-E1 ET-9RS-4SC-E1 ET-9RS-4ST-E1 ET-9RS-5SC-E1 ET-9RS-5ST-E1 ET-9RS-5SCL-E1 ET-9RS-5STL-E1 RJ45 Ports 9 8 8 8 8 8 8 7 7 7 7 7 7 FIBER Ports MECHANICAL DRAWING 1 multimode SC 4 km 1 multimode ST 4 km 1 singlemode SC 20 km 1 singlemode ST 20 km 1 singlemode SC 40 km 1 singlemode ST 40 km 2 multimode SC 4 km 2 multimode ST 4 km 2 singlemode SC 20 km 2 singlemode ST 20 km 2 singlemode SC 40 km 2 singlemode ST 40 km Note: Contact Sixnet for special or long haul fiber transceivers up to 120 km. The suffix 1 means preconfigured for 1 ring. Contact Sixnet for other options. Sixnet Technology Park 331 Ushers Road • Ballston Lake, NY 12019 • USA 1.518.877.5173 • Fax 1.518.877.8346 • [email protected] SOLUTIONS FOR YOUR INDUSTRIAL NETWORKING CHALLENGES Datasheet ET-9RS Rev April 15, 2009 WWW.SIXNET.COM