PRODUCT DATASHEET SLX-5MS-MDM REMOTE ACCESS SWITCH (ETHERNET MODEM) The SLX-5MS-MDM is a Remote Access Switch (Ethernet Land-Line Modem) that combines an industrial telephone modem with a 5 port industrial Ethernet managed switch. This powerful combination allows you to easily and securely access your Ethernet network from any remote location over standard telephone lines. Avoid those costly site visits. Save time and money! PRODUCT HIGHLIGHTS Slim 5 port Industrial Ethernet managed switch with integrated industrial telephone modem Easy and secure dial-in and dial-out connections up to 56 Kbps using PPP (point-to-point protocol) Easy to configure management and modem functions including PPP, SNMP, VLAN, QoS, IGMP and much more Truly rugged design with -40 to 75°C operation REAL-TIME SECURE PERFORMANCE Advanced PSTN modem features Make easy and secure dial-in connections Automatic dial-out on a trigger input Connection speeds up to Fast 56K (V.90) Full data compression and error control supported Compliant with telephone systems world-wide Advanced Ethernet switch features Five 10/100 fast Ethernet ports Auto-speed/duplex, auto-crossover & auto-polarity Plug and play operation or full management ability RSTP, VLAN, IGMP, QoS, SNMP and more Easy configuration with web or terminal interfaces Secure connections with HTTPS, SSL, SSH, SNMPv3 … Router Information Protocol (RIP) TROUBLE FREE OPERATION High Mean Time Between Failure (MTBF) rating Free field-installable upgrades forever -40 to +75 °C operation – no fans or moving parts! UL / CSA (CUL), CE and Hazloc (Zone 2) rated Enhanced surge and spike protection Dual (redundant) power inputs Alarm output and trigger input for PLC (or other device) SOLUTIONS FOR YOUR INDUSTRIAL NETWORKING CHALLENGES WWW.SIXNET.COM REMOTE ACCESS SWITCH & ETHERNET MODEM SPECIFICATIONS NETWORKING FEATURES Auto-detecting, auto-crossover and auto-polarity Store and forward wire speed switching Rapid Spanning Tree (RSTP) for fault-tolerant loops Priority queuing (QoS) for real-time performance SNMP v1 and V2 for network management SNMP v3 for authentication and encryption IGMP v1 & v2 for IP multicast filtering VLAN (port & tag based) for traffic segregation Message filtering to stop broadcast/multicast storms DHCP client for automatic IP address assignment RMON and port mirroring for diagnostics Configuration via secure (https) Web interface, Telnet / SSH (network), terminal (RS232) or SNMP (v1, v2, v3) Router Information Protocol (RIP) ETHERNET PERFORMANCE 5 Ethernet ports Ethernet switch type managed All IEEE 802.3 Ethernet protocols supported RJ45 ports (shielded) 10/100BaseTX RJ45 speed (10 or 100 Mbps) auto-negotiation RJ45 MDI/MDIX auto-crossover RJ45 TD and RD auto-polarity Typical latency for 10M ports =16 us + frame time; varies on load and settings Typical latency for 100M ports = 5 us + frame time; varies on load and settings Full or half duplex operation are configurable MAC addresses supported 2048 Memory bandwidth 3.2 Gbps Ethernet isolation 1500 VRMS 1 minute ETHERNET COMPLIANCE IEEE 802.3 (10Mbps Ethernet supports legacy devices) IEEE 802.3u (Fast Ethernet 100Mbps for newer devices) IEEE 802.3x (Full-Duplex with Flow Control) IEEE 802.1D/w (Rapid Spanning Tree for redundant rings and Spanning Tree for interoperability) IEEE 802.1p (Priority Queuing – QoS, CoS, ToS/DS) IEEE 802.1Q (VLAN for traffic segregation) RS232 MANAGEMENT RJ45 port Fixed baud rate, data bits, parity, stop bits, flow control 9600 Bps, 8, None, 1, None INDUSTRIAL PHONE MODEM PSTN modem Maximum data rates 56 Kbps Compatibility V.90, V.34, V.32, V.32 bis, V.22, V.22 bis, V.21 Data compression V.42 bis Error correction V.42 MNP or LAP Ringer 0.3 Jacks 2 RJ11 (phone and line) Standard AT and S register command sets Country compatibility world-wide (100+ countries) Telecom ratings FCC Part 68; Industry Canada S03-8; CTR21 (98/482/EC); ACA TS 001 and ACA TS 002 SLX-5MS-MDM PLC INPUT & OUTPUT Trigger (in) & alarm (out) signals PLC / Alarm output voltage; same as switch input power Maximum current output 0.5 Amp PLC / Trigger input voltage 10-30 VDC Typically current input 6.5 mA @ 24 VDC POWER INPUT Input power (all ports active) 5.0 W typical Input voltage (all models) 10-30 VDC (continuous) Transient protection 15,000 watts peak Spike protection 5,000 watts (10 times for 10 uS) ENVIRONMENTAL Operating temperature range -40 to +75 °C (cold start at -40°C) Storage temperature range -40 to +85 °C Humidity (non-condensing) 5 to 95% RH Vibration IEC60068-2-6 STANDARDS COMPLIANCE Electrical safety UL508/CSA C22.2/14; EN61010-1, CE EMI emissions FCC part 15, ICES-003; EN6100-6-4, CE EMC immunity IEC61000-6-2, CE Hazardous locations UL1604, CSA C22.2/213 (Class I, Div. 2); EN60079-15 (Zone 2, Category 3), CE (ATEX) PHYSICAL DIN rail or direct panel mounting (2 ways) Packaging (IP30) corrosion-resistant aluminum Weight 10 oz (0.28 kg) Dimensions - see mechanical drawing All specifications are subject to change. Consult factory for latest info. ORDERING GUIDE SLX-5MS-MDM-1 5 port industrial Ethernet managed switch with integrated modem Contact Sixnet for special Fiber models. MECHANICAL DRAWING 3.82" [9.70 cm] Removable Screw Block 4.70" [11.94 cm] Snaps to standard DIN Rail EN50022 (35 mm) Removable DIN clip for direct panel mounting 5.20" [13.21 cm] Panel mounting ears accept up to a #6 screw on older models (see to the right for newer models) 2.00" [5.08 cm] 4.21" [10.70 cm] See the User Manual for a More Detailed Diagram Sixnet Technology Park 331 Ushers Road • Ballston Lake, NY 12019 • USA 1.518.877.5173 • Fax 1.518.877.8346 • [email protected] SOLUTIONS FOR YOUR INDUSTRIAL NETWORKING CHALLENGES Datasheet SLX-5MS-MDM Rev. June 05, 2009 WWW.SIXNET.COM