331 Ushers Road, P.O. Box 767, Clifton Park, NY 12065 USA +1 (518) 877-5173, Fax +1 (518) 877-8346 mailto: [email protected] http://www.sixnetswitch.com Real-Time Ring™ Switch with Gigabit Fault-tolerant Ethernet Switches for Deterministic Systems SIXNET Real-time Ring™ switches provide very fast, fault-tolerant network redundancy and prioritized message delivery needed in critical real-time systems. Real-time Rings self-configure and just run, without the complex configuration steps required by alternative solutions. This break-through product delivers reliability and performance, saves you money, and makes your job easier. Ideal for: • 3 Gigabit ports for super fast connections • Real-time control o One auto-detecting 10/100/1000 RJ45 port • Distributed systems o Two flexible Gigabit ports for fiber or copper • Outdoor / marine use o Gigabit fiber connections up to 70+ km • Real-time fault-tolerant rings o Recovery time of 30 mS plus 5 mS per hop! o Ideal for deterministic systems and PLCs o Real-time Modbus over Ethernet monitoring • Real-time traffic prioritization o Assure delivery of real-time data o Improve network utilization (see page 2) o User settable priority assignments • Managed Switch features – at a lower cost o User configurable port settings o Port mirroring for traffic diagnostics o Pre-configurable for plug and play simplicity • SIXNET reliability and long-term support o Ultra-reliable 1,000,000 hours MTBF o Unique 20-year support policy o Firmware upgrades are FREE forever • Certified for harsh industrial environments o -40 to +85 °C operating range o Dual power inputs with superior spike protection o UL, CSA, CE, DNV and CENELEC rated Certified to Perform: ISO9001 Certified Class 1, Div II & Cenelec Zone 2 Ensure the reliability of your network with ultra-fast automatic switchover on a segment failure. Marine & Offshore European Community UL508 for Safety Backup path quickly restores communications TM R gTM S ng Riin Deelliivveerr mee R heess D Tiim wiittcch Sw Reeaall--T U Ullttrraa--D Deep peen nd daab bllee R Reessu ullttss Fault-tolerant Systems Survive Breaks Real-time Rings have an alternative network path in constant readiness. When a network node or cable segment fails, the Real-time Ring instantly redirects the traffic through the alternative path of the ring. Achieve Deterministic Performance Rings are simple by design. The alternative path is unique and well known and the action to take when a failure occurs is predetermined. Ring Switches use this knowledge to deliver deterministic performance, with recovery times of 5 mS plus some overhead. (The link loss recovery is 30 mS plus 5 mS times the number of Real-time Ring Switches in the ring. For example, 10 ring switches will recover in less than 80 mS.) Avoid the High Cost and Complexity of Managed Switches Real-time Ring Switches are the ideal way to achieve fault tolerance without the higher cost and complexity of Managed Switches. In most situations, Real-time Ring Switches will do what you need with just the factory pre-configuration. A simple Windows wizard (supplied at no cost) allows you to fine tune the performance if you like. These auto-configuring switches eliminate the learning curve associated with more complex network devices. Now you can get the job done without needing help from the "IT" department. Priority Queuing For Real-time Performance Customers tell us that the new security cameras added to their networks are slowing down their real-time data delivery. Real-time Ring Switches can tag the camera ports as lower priority (or you can set the critical data as a higher priority). In any event, the data will travel from switch to switch using priority queuing best suited for your situation. Real-time Ring switches will cure your data overload headaches – without significant effort or expense! Connect Independent Rings Together Real-time Ring Switches may be members of more than one ring. This capability permits you to design fast, work-cell oriented rings that are joined to each other to exchange information. (Smaller rings recover faster and are more reliable.) Mix Fast Ethernet and Gigabit Ring Switches Combine fast and gigabit ring switches to optimize for speed versus cost. The Realtime Ring™ capability is 100% compatible between these switches. Alarm Output and Modbus Avoid Future Problems An “OK” contact assures that the redundant power inputs and the ring (or rings) are complete. Modbus registers report the readiness of individual ports to your SCADA or control system. This is a SIXNET exclusive feature. Real-time Switches Deliver Ultra Reliability Real-time Ring Switches have field-proven reliability of more than 1,000,000 hours MTBF. These SIXNET industrially hardened switches are certified to survive in your harsh environment – even outdoors in marine and military applications. SIXNET Industrial Switches Make Your Job Easier In most applications, the factory pre-configuration will just work for you. Snap these switches onto the rail, plug in your network cables, and sit back and watch the data flow, year after year. These switches have been specifically designed to make your job easier. 331 Ushers Road, P.O. Box 767 y Clifton Park, NY 12065 USA y +1 (518) 877-5173 Fax +1 (518) 877-8346 y mailto:[email protected] y http://www.sixnetswitch.com Performance Specifications General Ethernet switch type Ethernet protocols supported RJ45 ports 1 – 6 (shielded) RJ45 port 7 (shielded) RJ45 ports 8 and 9 (shielded) RJ45 port speed RJ45 MDI/MDIX RJ45 TD and RD polarity SFP ports 8 and 9 (pluggable) Fiber optic port speed Fiber optic port wavelength Fiber multimode (mm) optimal Fiber singlemode (sm) optimal Fiber max. distance (full duplex) Typical latency for 10 Mbps ports Typ. latency for 100 Mbps ports Full or half duplex operation MAC addresses supported Memory bandwidth Status Reporting Modbus status registers “OK” contact output Real-Time Ring™ Features Maximum switches in ring Dual ring support Link loss recovery time Environmental Power input Input power @ 24 VDC Power input voltage Transient protection Spike Protection Ethernet isolation Operating temperature range Storage temperature range Humidity (non-condensing) Vibration Electrical safety EMI emissions EMC immunity Hazardous locations Marine and off-shore Eye safety (fiber models) Packaging (high temp. Lexan & rust-free aluminum case) Dimensions (L x W x H) 9 Ethernet ports including Gigabit Intelligent store & forward All IEEE 802.3 10/100BaseTX 10/100/1000BaseTX 10/100/1000BaseTX (-1 model) Auto-negotiation Auto-crossover Auto-polarity Fiber or RJ45 depending on module 100 Mbps or 1000 Mbps 850, 1310 or 1550 nm center 62.5/125 um (LC connector) 9/125 um (LC connector) 0.5 km (mm), 10 km (sm) or more 16 us + frame time Varies on load & settings 5 us + frame time Configurable 8192 32 Gbps Power & operational status Modbus Ethernet over UDP Sourcing power @ 0.5 Amp SIXNET Exclusive 50+ Yes 30 mS plus 5 mS per hop DIN rail or direct panel mounting Redundant input terminals 8.0 W (typical with all ports active) 10-30 VDC 15,000 watts peak 5,000 watts (10x for 10 uS) 1500 VRMS 1 minute -40 to +85 °C -40 to +85 °C 5 to 95% RH IEC68-2-6 UL508/CSA C22, EN61010-1 FCC part 15, ICES-003, EN55022 IEC61326-1 UL1604, CSA C22.2/213 (Class 1, Div. 2), Cenelec EN50021 (Zone 2) DNV (Det Norske Veritas) IEC60825-1, Class 1; FDA 21 CFR 1040.10 and 1040.11 IP30 protection; UL 94V-0 flame resistent packaging See next page Hardware Highlights: 9 port truly industrial Ethernet switch with up to three Gigabit ports (RJ45 copper, fiber optic or mixed) Up to two Gigabit fiber optic ports (multimode or singlemode for distances up to 70 km or more) Output for reporting power and operational status Redundant power inputs and enhanced surge/spike protection Industrial rated -40 to +85 °C operation (without fans!) UL/CSA, CE and Zone 2 rated for hazardous locations DNV tested for marine and off-shore use DIN rail or direct panel mounting (no extra kits required) Networking Features: Store and forward wire speed switching – no delays 32 Gbps high throughput for max speed on all ports Support for up to 8192 MAC addresses Automatic address learning, aging and migration Full-Duplex operation with flow control (no collisions!) Auto crossover (MDI/MDIX) and auto polarity Real-Time Ring™ for ultra-fast fault-tolerant loops Modbus over Ethernet status monitoring Priority queuing for real-time network performance Message filtering to prevent broadcast storms Port mirroring for advanced diagnostics Easy to use Windows configuration utility Ordering Guide ET-9RG-MM-D1 0 Pre-set for 0 rings (special order) 1 Pre-set for 1 ring (standard) 2 Pre-set for 2 rings (special order) C Custom configured for you D dual power is standard 1 all RJ45 copper ports MM two multimode fiber ports SS two singlemode fiber ports Many other combinations are available. Contact SIXNET for details. Specifications are subject to change. Consult factory for latest information. Ethernet Compliance: IEEE 802.3z (Gigabit 1000 Mbps Ethernet connections) IEEE 802.3u (Fast Ethernet 100 Mbps for newer devices) IEEE 802.3 (10 Mbps Ethernet supports legacy devices) IEEE 802.3x (Full-Duplex with Flow Control) IEEE 802.1p (QoS / CoS – Quality & Class of Service) Part # Example: ET-9RG-MM-D1 has six 10/100 RJ45, one 10/100/1000 RJ45 and two Gigabit multimode fiber with ports 8 & 9 pre-set for a ring. Setup Wizard RM-PS-024-01F SP-ETH-2 Accessories: Free Windows configuration tool Power supply – AC to 24VDC, 1A Dual port Ethernet surge & lightning protector for 10/100 ports 331 Ushers Road, P.O. Box 767 y Clifton Park, NY 12065 USA y +1 (518) 877-5173 Fax +1 (518) 877-8346 y mailto:[email protected] y http://www.sixnetswitch.com ET-9RG Mechanical Dimensions 6.25" [15.88 cm] 0.28" [0.70 cm] 0.50" [1.27 cm] (max. for SFP fiber) DIN EN 50022 (not included) 3.77" [9.58 cm] Front View 0.84" [2.12 cm] 0.17" [0.43] (clear for #8 screw) 3.54" [8.98 cm] Power 5.98" [15.18 cm] 1.38" [3.5 cm] Side View 2.30" [5.84 cm] 2.19" [5.55 cm] 1.95" [4.95 cm] DIN EN50022 (not included with units; not shown to scale; for reference only) 1.06" [2.7 cm] 1.58" [4.02 cm] ET-9RG Power and Alarm Connections Redundant DC Power Single DC Power P1 P2 P1 P2 OK + - To Panel + VDC Supply Alarm Output Load To Panel OK + - + - Alarm Output Load + VDC Supplies 331 Ushers Road, P.O. Box 767 y Clifton Park, NY 12065 USA y +1 (518) 877-5173 Fax +1 (518) 877-8346 y mailto:[email protected] y http://www.sixnetswitch.com 0.30" [0.76 cm] A AC Coom mpplleettee F Faam miillyy ooff II//O O SSoolluuttiioonnss Ethernet and RS485 I/O SIXNET can provide you the building blocks for the open systems you are looking for. Three complementary families of modular DIN rail mounted I/O provide local, remote, enterprise level, or Internet I/O solutions. Industrial Telephone Modems SIXNET rugged industrial modems eliminate the hassles of mounting a telephone modem in an industrial enclosure. These robust modems are rated for -30 to +70 ºC industrial operation. Industrial Ethernet Managed Switches SIXNET Industrial Ethernet Switches offer the most advanced features, from Rapid Spanning Tree Protocol for redundancy, to SNMP for easy network management. These switches are rugged, reliable, real-time and most of all, secure. Contact us for Gigabit options! Controllers & RTUs with Open-Source Linux SIXNET IPm is a combination of installation-ready industrial controllers & RTUs and a wealth of powerful software solutions. IPm offers the reliability of a PLC, the familiarity of powerful Windows programming and configuration utilities, all combined with powerful open-source Linux flexibility. Contact your SIXNET Applications Engineer Today! For the latest information, check out http://www.sixnetswitch.com 331 Ushers Road, P.O. Box 767 y Clifton Park, NY 12065 USA y +1 (518) 877-5173 Fax +1 (518) 877-8346 y mailto:[email protected] y http://www.sixnetswitch.com Gigabit Ring Switch Datasheet - Rev 9-Nov-06 Request Your FREE Product CD at http://www.sixnetswitch.com