Zinc Oxide Varistor Series ( Standard Surge ) : How to Order : 10 Element Size 5:ψ5mm D Series D: D Series 471 K Varistor Voltage Tolerance B Packing Form 180:18V K: ±10% B: Bulk 7:ψ7mm 471:470V L: ±15% T: Taping Ammo 10:ψ10mm 102:1000V M: ±20% R: Taping Reel 14:ψ14mm 182:1800V 20:ψ20mm Zinc OXDE VARISTOR Zinc oxide varistor is a voltage dependent resistor with symmetrical voltage-current characteristics that is designed to protect all kinds of electronic devices or elements from switching and induced lightening surges. It’s non linear exponent characteristic with froad using range and mass production is gradually being used by various level of electric engineering. FEATURES *Fast response time. *Low leakage current. *Excellent voltage ratio. *Wide voltage & energy ratio. *Low standby power and no follow on current. *High performance in surge current handling capability. *High performance in clamping voltage characteristics. V-I Characteristics of Varistor APPLICATIONS *IC, diode, transistor, thyristor, triac, and other semiconductor protection. *Suppression of mainborne transients in consumer electronics and industrial electronics. *Suppression of internally generated spikes in electronics circuit. *Surge protection in communication, measuring and controller electronics. *Surge protection in electronic home appliances and gas and petroleum appliances. *Relay and electromagnetic valve surge absorption. The varistor's rest state has a high impedance (several megaohms) in relation to the component to be protected and does not change the characteristics of the electric circuit. In the presence of transient voltage (over the breakdown voltage of varistor), the varistor then has a low impedance (a few ohms) and short circuits, i.e. the assembly E to the protected. PARAMETERS DEFINITION *Varistor Voltage (Breakdown voltage): The varistor voltage is the voltage across the varistor measures at a specified current Ic (0.lmA or 1mA) of specified duration. *Maximum allowable voltage: The maximum allowable voltage corresponds to the rest state of the varistor. The rest state voltage offers a low leakage current in order to limit the power consumption of the protected device and not to disturb the circuit to be protected. *Non linear exponent (α): The varistor voltage-current characteristic is defined by the equation: 1=KV α where K is a constant dependent on geometry, and α is the non linear exponent. We usually take two points (V1, I1), (V2, I2) to estimate the value of α. α=(log Il/I2) / (log V1/V2) In which I1 and I2 are the current value corresponding to the voltage value V1 and V2. *Maximum clamping voltage: Maximum clamping voltage is the maximum voltage Vp between two terminals with the specified standard impulse current I (8×20μ sec). The voltage value is an indication on the protective function of the varistor. CURRENT-VOLTAGE CHARACTERISTICS *Withstanding surge current: Withstanding surge current is the maximum peak current for he varistor with the specified standard impulse current (8×20μ sec) applied on time or two times and corresponding to a permissible variation of 10% in the varistor voltage change. *Energy Maximum energy from one or a burst of pulses. It is the value within the varistor change of±10% when on impulse of l0×1000μ sec us applied. E=KxVmxImxT E: Energy K: Constant=1.4 Vm: Max. clamping voltage at 1m. 1m: Max. allowable single surge current of l0×1000μ sec. T: Duration of surge current (1000μ sec) *Rated power The maximum power that can be applied within the specified ambient temperature. *Capacitance The capacitance of varistor is the reference value measured between the varistor terminals at specified frequency. *Pulse lifetime rating This is expressed as the maximum allowable number of impulse currents applied. 8×20μ sec impulse current (or l0×1000μ sec) is applied at prescribed interval. This curve also provides for derating current as required with repetitive pulsing. SOURCE OF SURGE VOLTAGE *Direct lightning surges. *Surge voltage by grounding fault. *From magnetic induction. *Induced lightning surges. *Surge voltage by switching operation. *From electrostatic induction. HOW TO SELECT VARISTOR *To identify the source and route of surge. *To decide the connection method of varistor. *To decide varistor voltage and max. clamping voltage. *To decide surge current waveform by calculation from surge voltage and surge impedance. *To check whether the withstanding surge current and surge life of varistor is sufficient or not. *To check the variation of electric power of protected device. *To check whether the max. energy and energy life of the varistor is enough or not. *To check the relation: Max. withstanding bvoltage of protected device>Max. clamping voltage of varistor>The real clamping voltage occurred>Breakdown voltage of varistor>Operating voltage of protected device. *To check whether the loss of capacitance of varistor in operation condition. *To check whether the problem caused by loss current of leakage. *To check the connection method of varistor. *To check the condition of varistor overload. *To check any other problems by various operation conditions. *To test and to verify by real practice. *To check the connection of the grounding wire. SPECIFICATION SHEET P/N : JNR5D271KBN Spec. Part No. JNR5D271KBN Varistor Voltage V1mA Maximun Allowable Voltage Voltage Withstanding Surge Current (8/20us) Maximun Clamping (V) Acrms (V) DC (V) V5A (V)max 1Time (A) 2Time (A) 270 (247-303) 175 225 475 400 200 Dimension Table Unit : mm Dia Code ˗(±0.5) d(±0.05) F(±1.0) h max. L min. a ( ±1.0) T max. 5D 6.0 0.6 5.0 11.0 25.0 1.2 5.0 Temperature range: Storage temperature: Temperature Coefficient of voltage: -40℃ ~ +85℃ -40℃ ~ +125℃ -0.05%/℃ Rated Energy Reference Wattage 10/1000us Capacitance (W) (J) 1KHZ (PF) 0.1 9.9 75