4 5.08 4 2X .200 THRU D 3 30.48 1.200 THRU 66.68 2.625 3 DO NOT SCALE DRAWING 38.10 1.500 15.24 .600 TYP. 60.96 2.400 86.36 3.400 TYP. EACH END 10.16 .400 ENCLOSURE MOUNTING FLANGE 50.80 2.000 MODULE "A" PIN 1A 6.35 .250 TYP. EACH END 41.91 1.650 101.35 3.990 2.16 .085 MODULE "B" PIN 1A 97.03 3.820 RECOMMENDED PCB LAYOUT 119.38 4.700 47 EQUAL SPACES @ [2.54] .100 C 2.16 .085 5 14.22 7 .560 60.96 2.400 D 43.18 1.700 TYP. EACH END 30.48 1.200 TYP. EACH END HARDWARE NOT SHOWN FOR CLARITY 119.38 4.700 TYP. 47 EQUAL SPCS. @[2.54] .100 B DATE ENGR 10/01/12 S MARSHALL DESCRIPTION REV C ECN #4278 M3 X 0.5 - [8.89].35 DP. TYP. 10 PLCS. USED FOR MOUNTING ENCLOSURE 50.80 2.000 22.86 .900 TYP. 9 EQUAL SPCS @ [2.54] .100 60.96 2.400 TYP. EACH END REVISIONS 48.51 1.910 TYP. EACH END 63.88 2.515 2 59.69 2.350 1 THE INFORMATION CONTAINED HEREIN IS THE EXCLUSIVE PROPERTY OF VIRGINIA PANEL CORPORATION AND IS SUBMITTEDFOR USE BY THE CUSTOMER ONLY. THE DATA SHALL NOT BE DUPLICATED, USED, OR DISCLOSED IN WHOLE OR IN PART FOR ANY PURPOSE OTHER THAN TO MAINTAIN THE EQUIPMENT PROVIDED. CONSULT WITH VIRGINIA PANEL CORPORATION ENGINEERING IF MORE DETAIL IS REQUIRED. 5.59 2 8X .220 THRU CLEARANCE FOR [0.64].025 ROUND SOLDER POST TYP. 960 PLCS. 133.35 5.250 C 2 158.75 6.250 B 154.43 6.080 5 86.36 3.400 60.96 2.400 22.86 .900 9 EQUAL SPACES @ [2.54] .100 60.96 2.400 CONNECTOR MATING VIEW A 7 MINIMUM .60" 6 RECOMMENDED MAXIMUM EXTERNAL HEIGHT FOR ENCLOSURE 5 RECOMMENDED MINIMUM INTERNAL LENGTH AND WIDTH FOR ENCLOSURE 4 3 KEYING ACCESS HOLES. REQUIRED FOR RECEIVER PCB, OPTIONAL FOR ITA PCB BUT RECOMMENDED FOR CONVENIENCE. 2 1 NOTES: 6.24 .245 HOLE RECOMMENDED FOR HANDLE CLEARANCE IN ENCLOSURE 70.41 2.772 69.85 2.750 6 .07 X 45° TYP. CUSTOMER DRAWING A VIRGINIA PANEL CORPORATION WWW.VPC.COM CLEARANCE HOLE FOR SYSTEM ENGAGING MECHANISM. REQUIRED FOR ITA PCB ONLY. NO HOLE REQUIRED FOR RECEIVER SIDE. IF PCB LENGTH EXCEEDS THE [63.88]2.515 DIMENSION IN THE DIRECTION SHOWN OR THE OPPOSING DIRECTION ACCOMODATIONS FOR REMOVING THE MODULE MOUNTING SCREWS MUST BE MADE BY DRILLING THE [5.59].220 THRU HOLES ON ITA PCB ONLY. FOR APPLICATION USE & CARE INFORMATION CONSULT VPC USERS GUIDE @WWW.VPC.COM 4 16.26 .640 3 2 DIMENSIONS ARE SHOWN AS: [MILLIMETERS] INCHES SIZE C ICON 960 ITA w/ LOADED MODULES CAGE CODE 18117 SCALE: 1:2 DWG.NO. 410124103 1 410124103 2/1/07 SHEET REV C 1