VIRGINIA PANEL CORPORATION icon user’s manual: SECTION 8 PCB layout and mounting Signal Module, Receiver, QuadraPaddle, iCon, 160 Position, Fully Loaded with Twin Female Contacts • part # 510 160 105 PCB layout for the iCon Receiver, Part # 310 123 101 loaded with two 510 160 105 modules. Thru hole and pad diameters are for VPC QuadraPaddle Adapter Contact, Part #610 138 117. The size of these holes may be different if a header from a different manufacturer is used. Also shown are optional clearance holes. VPC modules/pin mount this side. 16.38±0.25 .645±.010 8.26 .325 22.86 .900 1 9 EQUAL SPACES @.100 TYP. 2 PATTERNS 14.61±0.25 .575±.010 8.26 .325 6.48±0.25 .255±.010 66.04 2.60 51.05 2.01 38.10 1 1.500 15 EQUAL SPACES @.100 TYP. 2 PATTERNS PIN A1 PIN A16 136.91 5.39 66.04 2.600 120.65 4.750 1 PIN A1 51.05 2.01 PIN A16 320X 037 .003 [0.094 0.08] PLATED THRU HOLE .054 .003 [1.37 0.08] SOLDER PAD 5.08 6X .20 THRU 4X .14 3.43 THRU OPTIONAL CLEARANCE HOLES FOR ACCESS CLEARANCE HOLES FOR TO MODULE MNTG SCREWS AND RECEIVER MOUNTING HARDWARE KEYING PIN ACCESSORY SCREWS 2X .129 [3.26] THRU .01 LOCATION TOLERANCE APPLIES .01 LOCATION TOLERANCE APPLIES .225 [5.72] X 82° FAR SIDE PCB TO RECEIVER MOUNTING HOLES USES TWO 4-40 FLATHEAD SCREWS RECOMMENDED PCB LAYOUT .005 LOCATION TOLERANCE APPLIES CONNECTOR MOUNTS THIS SIDE TOLERANCES ARE: .XX= [0.25] .01 .XXX= [0.13] .005 UNLESS OTHERWISE SPECIFIED 1 .0021 LOCATION TOLERANCE APPLIES TO PLATED THRU HOLES 8-4 For the most current information available, visit www.vpc.com. 5/4/15 VIRGINIA PANEL CORPORATION icon user’s manual: SECTION 8 PCB layout and mounting QuadraPaddle Signal/Micro Power or Micro Coaxial Module, Receiver, iCon, 100/15 Position, with Twin Female Signal • part # 510 160 112 QuadraPaddle Signal/Micro Power or Micro Coaxial Module, Receiver, iCon, 100/15 Position, Fully Loaded with Male Posts • part # 510 160 113 PCB layout for the iCon Receiver, Part # 310 123 101 loaded with two 510 160 112/113 modules. 200 thru hole and pad diameters are for VPC QuadraPaddle Adapter Contact, Part #610 138 117; 30 thru hole and pad diameters are for VPC Micro Power contact, Part # 610142102. The size of these holes may be different if a header from a different manufacturer is used. Also shown are optional clearance holes. VPC modules/pin mount this side. CLEARANCE HOLES FOR ACCESS TO KEYING FEATURE MOUNTING SCREWS 2 X .200[5.08] THRU .900 9 PLCS. @ .100 1 TYP. 2 PATTERNS CLEARANCE HOLES FOR FRAME MOUNTING SCREWS 4 X .135[3.43] THRU 14.61±0.25 .575±.010 8.26 .325 TYP. 16.38±0.25 .645±.010 6.48±0.25 .255±.010 35.31 1.39 51.05 2.01 66.04 2.600 136.91 5.39 8.26 .325 22.86 .90 9 PLCS. @ .100 TYP. 2 PATTERNS PIN A1 1 66.04 2.60 PIN A10 1 120.65 4.750 PIN A1 51.05 2.01 9.65 .38 2 PLCS. @ .190 TYP. 2 PATTERNS 1 PIN A10 19.30 .76 1.78 .07 TYP. RECOMMENDED PCB LAYOUT CONNECTOR MOUNTS THIS SIDE TOLERANCES ARE: .XX= [0.25] .01 .XXX= [0.13] .005 UNLESS OTHERWISE SPECIFIED 1 .0021 LOCATION TOLERANCE APPLIES TO PLATED THRU HOLES TOLERANCE N0N-ACCUMULATIVE ON HOLE PATTERNS 8-5 CLEARANCE HOLES FOR ACCESS TO MODULE MOUNTING SCREWS 4X .200[5.08] THRU .760 TYP. 4 PLCS. @ .190 TYP. 2 PATTERNS 1 [0.94 0.08] .037 .003 PLATED THRU HOLE [1.52] .060 PAD TYP .200 PLCS EACH [2.54 0.08] .100 .003 PLATED THRU HOLES [3.18] .125 PAD TYP 30 PLCS EACH 3&%02817,1*+2/(686(6 ;7+5($')/$7+($'6&5(:6 ; 7+58$// ; )$56,'(237,21$/ For the most current information available, visit www.vpc.com. 5/4/15