® RT8077 2A, 2MHz, Synchronous Step-Down Converter General Description Features The RT8077 is a high efficiency synchronous, step-down DC/DC converter. Its input voltage range is from 2.6V to 5.5V and provides an adjustable regulated output voltage from 0.8V to 5V, while delivering up to 2A of output current. z The internal synchronous low on-resistance power switches increase efficiency and eliminate the need for an external Schottky diode. The switching frequency is set by an external resistor or can be synchronized to an external clock. The 100% duty cycle provides low dropout operation extending battery life in portable systems. z z z z z z z z z z Current mode operation with external compensation allows the transient response to be optimized over a wide range of loads and output capacitors. High Efficiency : Up to 95% Low RDS(ON) Internal Switches : 90mΩ Ω Programmable Frequency : 300kHz to 2MHz No Schottky Diode Required 0.8V Reference Allows for Low Output Voltage Low Dropout Operation : 100% Duty Cycle 2.6V to 5.5V Input Voltage Range VOUT Range from 0.8V to 5V Up to 2A Output Current Thermal Shutdown RoHS Compliant and Halogen Free Applications z The 100% duty cycle in Low Dropout Operation further maximize battery life. z The RT8077 is available in the WDFN-8L 2x2 package. z z z z z Portable Instruments Battery-Powered Equipment Notebook Computers Distributed Power Systems IP Phones Digital Cameras Dynamic Supply Bias for GSM/EDGE PAs and 3G/4G PAs Simplified Application Circuit VIN CIN ROSC PVDD COMP RT8077 FB RCOMP R2 CF RT PGND CCOMP R1 L1 LX GND Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 EN VOUT EN COUT is a registered trademark of Richtek Technology Corporation. www.richtek.com 1 RT8077 Ordering Information Marking Information RT8077 0B : Product Code Package Type QW : WDFN-8L 2x2 (W-Type) 0BW W : Date Code Lead Plating System G : Green (Halogen Free and Pb Free) Note : Pin Configurations ` ments of IPC/JEDEC J-STD-020. ` (TOP VIEW) RoHS compliant and compatible with the current requireSuitable for use in SnPb or Pb-free soldering processes. RT GND LX PGND 8 1 3 GND Richtek products are : 6 4 9 5 2 7 COMP FB EN PVDD WDFN-8L 2x2 Functional Pin Description Pin No. 1 Pin Name RT 2, GND 9 (Exposed Pad) Pin Function Switching Frequency Setting. Connecting a resistor to ground from this pin sets the switching frequency. Signal Ground. All small-signal components and compensation components should be connected to this ground, which in turn connects to PGND at one point. 3 LX Switch Node. Connect this pin to the inductor. 4 PGND Power Ground. Connect this pin close to the negative terminal of CIN and COUT. 5 PVDD Power Input. Decouple this pin to PGND with a capacitor. 6 EN Enable Control Input. A logic-high (1.2V < EN < 5.5V) enables the converter; logic-low forces the IC into shutdown mode. 7 FB Feedback Voltage Input. This pin receives the feedback voltage from a resistive divider connected across the output. 8 COMP Compensation Node. The current comparator threshold increases with this control voltage. Connect external compensation elements to this pin to stabilize the control loop. Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 2 is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Function Block Diagram EN RT PVDD ISEN SD OSC Slope Comp. COMP VREF FB EA OC Limit Output Clamp Internal Soft- Start Driver LX Controller Logic 0.2V NISEN POR OTP PGND N-MOSFET ILIM GND PVDD Operation The RT8077 is a synchronous low voltage Buck converter that can support the input voltage range from 2.6V to 5.5V and the output current can be up to 2A. The RT8077 uses a constant frequency, current mode architecture. In normal operation, the high-side P-MOSFET is turned on when the logic controller is set by the oscillator (OSC) and is turned off when the current comparator resets the logic controller. Oscillator (OSC) The internal oscillator runs at the programmable frequency range : 300kHz to 2MHz Enable Comparator The EN pin can be connected to VIN through a 100kΩ external resistor for automatic startup. Soft-Start (SS) High-side MOSFET peak current is measured by internal RSENSE. The Current Signal is where Slope Compensator works together with sensing voltage of RSENSE. The error amplifier EA adjusts COMP voltage by comparing the feedback signal (VFB) from the output voltage with the internal 0.8V reference. When the load current increases, it causes a drop in the feedback voltage relative to the reference, the COMP voltage then rises to allow higher inductor current to match the load current. UV Comparator If the feedback voltage (VFB) is lower than threshold voltage 0.2V, the UV Comparator's output will go high and the Switch Controller will turn off the high-side MOSFET. Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 An internal current source charges an internal capacitor to build the soft-start ramp voltage. The VFB voltage will track the internal ramp voltage during soft-start interval. The typical soft-start time is 1ms. is a registered trademark of Richtek Technology Corporation. www.richtek.com 3 RT8077 Absolute Maximum Ratings z z z z z z z (Note 1) Supply Input Voltage, PVDD --------------------------------------------------------------------------------------------Power Dissipation, PD @ TA = 25°C WDFN-8L 2x2 --------------------------------------------------------------------------------------------------------------Package Thermal Resistance (Note 2) WDFN-8L 2x2, θJA ---------------------------------------------------------------------------------------------------------Junction Temperature -----------------------------------------------------------------------------------------------------Lead Temperature (Soldering, 10 sec.) -------------------------------------------------------------------------------Storage Temperature Range --------------------------------------------------------------------------------------------ESD Susceptibility (Note 3) HBM (Human Body Model) ----------------------------------------------------------------------------------------------- Recommended Operating Conditions z z z −0.3V to 6.5V 0.833W 120°C/W 150°C 260°C −65°C to 150°C 2kV (Note 4) Supply Input Voltage, PVDD --------------------------------------------------------------------------------------------- 2.6V to 5.5V Junction Temperature Range --------------------------------------------------------------------------------------------- −40°C to 125°C Ambient Temperature Range --------------------------------------------------------------------------------------------- −40°C to 85°C Electrical Characteristics (VIN = 3.3V, TA = 25°C, unless otherwise specified) Parameter Min Typ Max Unit VREF 0.788 0.8 0.812 V Logic-High VEN_H 1.2 -- 5.5 Logic-Low VEN_L -- -- 0.4 VFB = 3.3V -- 0.1 0.4 VFB = 0.85V -- 270 -- Shutdown, VEN = 0V VIN = 2.6V to 5.5V -- -- 1 -- 0.1 -- %/V -- 0.4 -- % Error Amplifier Transconductance gm -- 400 -- μA/V Current Sense Transresistance -- 0.2 -- Ω ROSC = 180kΩ 1.44 1.8 2.16 Adjustable Switching Frequency Range 0.3 -- 2 Feedback Reference Voltage EN Input Voltage Feedback Leakage Current Symbol I FB Quiescent Current Output Voltage Line Regulation ΔVLINE Output Voltage Load Regulation ΔVLOAD VIN = 5V, VOUT = 3.3V, I OUT = 0A to 2A RS Switching Frequency Switch On-Resistance Test Conditions V μA μA MHz High-Side RDS(ON)_P I SW = 0.3A, PVDD = 3.6V -- 90 130 Low-Side RDS(ON)_N I SW = 0.3A, PVDD = 3.6V -- 90 130 I LIM 3 -- -- VDD Rising -- 2.4 -- VDD Falling -- 2.2 -- Rising -- 150 -- °C -- 20 -- °C Peak Current Limit Under-Voltage Lockout Threshold (Note 5) mΩ A V Over Temperature Protection Thermal Shutdown T SD Thermal Shutdown Hysteresis ΔTSD Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 4 is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Note 1. Stresses beyond those listed “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions may affect device reliability. Note 2. θJA is measured at TA = 25°C on a high effective thermal conductivity four-layer test board per JEDEC 51-7. Note 3. Devices are ESD sensitive. Handling precaution is recommended. Note 4. The device is not guaranteed to function outside its operating conditions. Note 5. Guaranteed by design. Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 is a registered trademark of Richtek Technology Corporation. www.richtek.com 5 RT8077 Typical Application Circuit VIN 5V 5 CIN 10µF x 2 ROSC 180k PVDD COMP 8 RT8077 FB 7 GND LX 3 EN 6 CCOMP 220pF R2 24k CF 1 RT 4 PGND 2, 9 (Exposed Pad) RCOMP 91k R1 75k L1 2.2µH EN COUT 44µF VOUT Up to 2A Table 1. Recommended Component Selection VOUT (V) R1 (kΩ) R2 (kΩ) RCOMP (kΩ) CCOMP (nF) L1 (μH) COUT (μF) 3.3 75 24 91 0.22 2.2 22x2 2.5 51 24 75 0.47 2.2 22x2 1.8 30 24 51 0.68 2.2 22x2 1.5 21 24 47 0.68 2.2 22x2 1.2 12 24 30 0.68 1 22x2 1 6 24 24 0.68 1 22x2 Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 6 is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Typical Operating Characteristics Output Voltage vs. Input Voltage Efficiency vs. Load Current 100 3.40 90 3.38 VIN = 4.2V Output Voltage (V) Efficiency (%) 80 VIN = 5V 70 60 50 40 30 20 3.36 3.34 3.32 3.30 3.28 3.26 3.24 10 3.22 VOUT = 3.3V, IOUT = 0A to 2A 0 0.001 VOUT = 3.3V, IOUT = 0A 3.20 0.01 0.1 1 10 3.5 3.75 4 4.25 1.25 2.50 1.24 2.45 1.23 2.40 5 5.25 5.5 1.22 2.35 Rising 1.21 VIN UVLO (V) Output Voltage (V) 4.75 VIN UVLO vs. Temperature Output Voltage vs. Output Current VIN = 5.5V 1.20 VIN = 3.3V 1.19 2.30 Falling 2.25 2.20 1.18 2.15 1.17 2.10 2.05 1.16 VOUT = 1.2V, IOUT = 0A to 2A 0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 VOUT = 3.3V 2.00 1.15 -50 2.0 -25 0 25 Frequency vs. Input Voltage 75 100 125 Frequency vs. Temperature 2.4 2.3 2.3 2.2 2.2 Frequency (MHz)1 2.4 2.1 2.0 1.9 1.8 1.7 2.1 VOUT = 1.2V VOUT = 3.3V 2.0 1.9 1.8 1.7 VIN = 5V, VOUT = 3.3V, IOUT = 0.6A VIN = 5V, IOUT = 0.6A 1.6 1.6 3.5 3.75 4 4.25 4.5 4.75 5 5.25 Input Voltage (V) Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 50 Temperature (°C) Output Current (A) Frequency (MHz)1 4.5 Input Voltage (V) Load Current (A) September 2013 5.5 -50 -25 0 25 50 75 100 125 Temperature (°C) is a registered trademark of Richtek Technology Corporation. www.richtek.com 7 RT8077 Current Limit vs. Temperature 6.0 5.5 5.5 5.0 5.0 Current Limit (A) Currrent Limit (A) Currrent Limit vs. Input Voltage 6.0 4.5 4.0 3.5 VIN = 5V VIN = 3.3V 4.5 4.0 3.5 3.0 3.0 2.5 2.5 VOUT = 1.2V VOUT = 3.3V 2.0 2.0 3.5 3.75 4 4.25 4.5 4.75 5 5.25 -50 5.5 -25 0 25 50 75 Input Voltage (V) Temperature (°C) Output Voltage vs. Temperature Output Ripple 100 125 3.45 Output Voltage (V) 3.42 VOUT (5mV/Div) 3.39 3.36 3.33 3.30 3.27 VLX (5V/Div) 3.24 3.21 3.18 VIN = 5V, VOUT = 3.3V, IOUT = 2A VIN = 5V, VOUT = 3.3V, IOUT = 0.3A 3.15 -50 -25 0 25 50 75 100 Time (250ns/Div) 125 Temperature (°C) Output Ripple Output Ripple VOUT (5mV/Div) VOUT (5mV/Div) VLX (5V/Div) VLX (5V/Div) VIN = 5V, VOUT = 3.3V, IOUT = 1A Time (250ns/Div) Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 8 VIN = 5V, VOUT = 1.2V, IOUT = 2A Time (250ns/Div) is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Output Ripple Output Ripple VOUT (5mV/Div) VOUT (5mV/Div) VLX (5V/Div) VLX (5V/Div) VIN = 3.3V, VOUT = 1.2V, IOUT = 2A VIN = 5V, VOUT = 1.2V, IOUT = 1A Time (250ns/Div) Time (250ns/Div) Output Ripple Power On from VIN VOUT (5mV/Div) VIN (5V/Div) VLX (5V/Div) VLX (5V/Div) VIN = 3.3V, VOUT = 1.2V, IOUT = 1A VOUT (2V/Div) I IN (2A/Div) VIN = 5V, VOUT = 3.3V, IOUT = 2A Time (250ns/Div) Time (1ms/Div) Power Off from VIN UVP Shutdown VIN = 5V, VOUT = 3.3V, IOUT = 2A VIN = 5V, VOUT = 3.3V, IOUT = 2A VIN (5V/Div) VOUT (2V/Div) VLX (5V/Div) VOUT (2V/Div) IOUT (5A/Div) VLX (2V/Div) Time (1ms/Div) Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 Time (2.5μs/Div) is a registered trademark of Richtek Technology Corporation. www.richtek.com 9 RT8077 UVP Shutdown Load Transient Response VIN = 4V, VOUT = 3.3V, IOUT = 2A VOUT (100mV/Div) VOUT (2V/Div) VLX (2V/Div) IOUT (1A/Div) Time (2.5μs/Div) Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 10 VIN = 5V, VOUT = 3.3V, IOUT = 1A to 2A Time (50μs/Div) is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Application Information The basic RT8077 application circuit is shown in Typical Application Circuit. External component selection is determined by the maximum load current and begins with the selection of the inductor value and operating frequency followed by CIN and COUT. Soft-Start The RT8077 contains an internal soft-start clamp that gradually raises the clamp on the COMP pin. Operating Frequency Selection of the operating frequency is a tradeoff between efficiency and component size. High frequency operation allows the use of smaller inductor and capacitor values. Operation at lower frequency improves efficiency by reducing internal gate charge and switching losses but requires larger inductance and/or capacitance to maintain low output ripple voltage. The operating frequency of the RT8077 is determined by an external resistor that is connected between the RT pin and GND. The value of the resistor sets the ramp current that is used to charge and discharge an internal timing capacitor within the oscillator. The RT resistor value can be determined by examining the frequency vs. ROSC curve. Although frequencies as high as 2MHz are possible, the minimum on-time of the RT8077 imposes a minimum limit on the operating duty cycle. The minimum on-time is typically 110ns. Therefore, the minimum duty cycle is equal to 110ns x f (Hz). Switching Frequency (MHz)1 3.0 2.5 100% Duty Cycle Operation When the input supply voltage decreases toward the output voltage, the duty cycle increases toward the maximum on-time. Further reduction of the supply voltage forces the main switch to remain on for more than one cycle eventually reaching 100% duty cycle. The output voltage will then be determined by the input voltage minus the voltage drop across the internal P-MOSFET and the inductor. Low Supply Operation The RT8077 is designed to operate down to an input supply voltage of 2.6V. One important consideration at low input supply voltages is that the RDS(ON) of the P-Channel and N-Channel power switches increases. The user should calculate the power dissipation when the RT8077 is used at 100% duty cycle with low input voltages to ensure that thermal limits are not exceeded. Slope Compensation and Inductor Peak Current Slope compensation provides stability in constant frequency architectures by preventing sub-harmonic oscillations at duty cycles greater than 50%. It is accomplished internally by adding a compensating ramp to the inductor current signal. Normally, the maximum inductor peak current is reduced when slope compensation is added. In the RT8077, however, separated inductor current signals are used to monitor over-current condition. This keeps the maximum output current relatively constant regardless of duty cycle. Short-Circuit Protection ROSC = 180k for 1.8MHz When the output is shorted to ground, the inductor current decays very slowly during a single switching cycle. A current runaway detector is used to monitor inductor current. As current increasing beyond the control of current loop, switching cycles will be skipped to prevent current runaway from occurring. 2.0 1.5 1.0 0.5 0.0 0 200 400 600 800 1000 ROSC OSC ((kΩ)) Figure 1 Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 is a registered trademark of Richtek Technology Corporation. www.richtek.com 11 RT8077 Inductor Selection The inductor value and operating frequency determine the ripple current according to a specific input and output voltage. The ripple current ΔIL increases with higher VIN and decreases with higher inductance. V V ΔIL = ⎡⎢ OUT ⎤⎥ × ⎡⎢1− OUT ⎤⎥ VIN ⎦ ⎣ f ×L ⎦ ⎣ Having a lower ripple current reduces not only the ESR losses in the output capacitors but also the output voltage ripple. However, it requires a large inductor to achieve this goal. For the ripple current selection, the value of ΔIL = 0.4(IMAX) will be a reasonable starting point. The largest ripple current occurs at the highest VIN. To guarantee that the ripple current stays below the specified maximum, the inductor value should be chosen according to the following equation : ⎡ VOUT ⎤ ⎡ VOUT ⎤ L =⎢ ⎥ × ⎢1 − VIN(MAX) ⎥ f I × Δ L(MAX) ⎣ ⎦ ⎣ ⎦ The inductor's current rating (caused a 40°C temperature rising from 25°C ambient) should be greater than the maximum load current and its saturation current should be greater than the short circuit peak current limit. CIN and COUT Selection The input capacitance, C IN, is needed to filter the trapezoidal current at the source of the top MOSFET. To prevent large ripple voltage, a low ESR input capacitor sized for the maximum RMS current should be used. RMS current is given by : V IRMS = IOUT(MAX) OUT VIN VIN −1 VOUT This formula has a maximum at VIN = 2VOUT, where I RMS = I OUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. The selection of COUT is determined by the Effective Series Resistance (ESR) that is required to minimize voltage ripple and load step transients, as well as the amount of bulk Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 12 capacitance that is necessary to ensure that the control loop is stable. Loop stability can be checked by viewing the load transient response as described in a later section. The output ripple, ΔVOUT, is determined by : ⎡ 1 ⎤ ΔVOUT ≤ ΔIL ⎢ESR + ⎥ 8fC OUT ⎦ ⎣ Using Ceramic Input and Output Capacitors Higher values, lower cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high voltage rating and low ESR make them ideal for switching regulator applications. However, care must be taken when these capacitors are used at the input and output. When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VDD. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN large enough to damage the part. Thermal Considerations For continuous operation, do not exceed absolute maximum junction temperature. The maximum power dissipation depends on the thermal resistance of the IC package, PCB layout, rate of surrounding airflow, and difference between junction and ambient temperature. The maximum power dissipation can be calculated by the following formula : PD(MAX) = (TJ(MAX) − TA) / θJA where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θJA is the junction to ambient thermal resistance. For recommended operating condition specifications, the maximum junction temperature is 125°C. The junction to ambient thermal resistance, θJA, is layout dependent. For WDFN-8L 2x2 packages, the thermal resistance, θJA, is 120°C/W on a standard JEDEC 51-7 four-layer thermal test board. The maximum power dissipation at TA = 25°C can be calculated by the following formula : PD(MAX) = (125°C − 25°C) / (120°C/W) = 0.833W for WDFN-8L 2x2 package is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 The maximum power dissipation depends on the operating ambient temperature for fixed T J(MAX) and thermal Layout Considerations Follow the PCB layout guidelines for optimal performance of RT8077. resistance, θJA. The derating curve in Figure 3 allows the designer to see the effect of rising ambient temperature on the maximum power dissipation. Maximum Power Dissipation (W) 0.9 ` A ground plane is recommended. If a ground plane layer is not used, the signal and power grounds should be segregated with all small-signal components returning to the GND pin at one point that is then connected to the PGND pin close to the IC. The exposed pad should be connected to GND. ` Connect the terminal of the input capacitor(s), CIN, as close as possible to the PVDD pin. This capacitor provides the AC current into the internal power MOSFETs. ` LX node is with high frequency voltage swing and should be kept within small area. Keep all sensitive small-signal nodes away from the LX node to prevent stray capacitive noise pick-up. ` Flood all unused areas on all layers with copper. Flooding with copper will reduce the temperature rise of power components. Four-Layer PCB 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 25 50 75 100 125 Ambient Temperature (°C) Figure 3. Derating Curve of Maximum Power Dissipation You can connect the copper areas to any DC net (PVDD, PGND, GND, or any other DC rail in your system). ` Connect the FB pin directly to the feedback resistors. The resistor divider must be connected between VOUT and GND. Connect the FB pin directly to feedback resistors. The resistor divider must be connected between VOUT and GND. VOUT GND CCOMP R2 R1 L1 VOUT RCOMP RT GND LX PGND 8 1 3 GND LX should be connected to Inductor by wide and short trace, keep sensitive components away from this trace. ROSC 6 4 9 5 2 COUT Output capacitor must be near RT8077. 7 CIN COMP FB EN PVDD CF VIN CIN must be placed between V DD and GND as closer as possible. Figure 4. PCB Layout Guide Copyright © 2013 Richtek Technology Corporation. All rights reserved. DS8077-01 September 2013 is a registered trademark of Richtek Technology Corporation. www.richtek.com 13 RT8077 Recommended component selection for Typical Application. Table 2. Inductors Component Supplier Series Inductance (μH) DCR (mΩ) Current Rating (mA) Dimensions (mm) TAIYO YUDEN NRS8040 2 10 8100 8x8x4 Table 3. Capacitors for CIN and COUT Component Supplier Part No. Capacitance (μF) Case Size TDK C3225X5R0J226M 22 1210 TDK C2012X5R0J106M 10 0805 Panasonic ECJ4YB0J226M 22 1210 Panasonic ECJ4YB1A106M 10 1210 TAIYO YUDEN LMK325BJ226ML 22 1210 TAIYO YUDEN JMK316BJ226ML 22 1206 TAIYO YUDEN JMK212BJ106ML 10 0805 Copyright © 2013 Richtek Technology Corporation. All rights reserved. www.richtek.com 14 is a registered trademark of Richtek Technology Corporation. DS8077-01 September 2013 RT8077 Outline Dimension D2 D L E E2 1 e SEE DETAIL A b 2 1 2 1 A A1 A3 DETAIL A Pin #1 ID and Tie Bar Mark Options Note : The configuration of the Pin #1 identifier is optional, but must be located within the zone indicated. Dimensions In Millimeters Dimensions In Inches Symbol Min Max Min Max A 0.700 0.800 0.028 0.031 A1 0.000 0.050 0.000 0.002 A3 0.175 0.250 0.007 0.010 b 0.200 0.300 0.008 0.012 D 1.950 2.050 0.077 0.081 D2 1.000 1.250 0.039 0.049 E 1.950 2.050 0.077 0.081 E2 0.400 0.650 0.016 0.026 e L 0.500 0.300 0.020 0.400 0.012 0.016 W-Type 8L DFN 2x2 Package Richtek Technology Corporation 5F, No. 20, Taiyuen Street, Chupei City Hsinchu, Taiwan, R.O.C. Tel: (8863)5526789 Richtek products are sold by description only. Richtek reserves the right to change the circuitry and/or specifications without notice at any time. Customers should obtain the latest relevant information and data sheets before placing orders and should verify that such information is current and complete. Richtek cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Richtek product. Information furnished by Richtek is believed to be accurate and reliable. However, no responsibility is assumed by Richtek or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Richtek or its subsidiaries. DS8077-01 September 2013 www.richtek.com 15