PrevaLED® Linear

www.osram.com/prevaled
introduction December 2013
PrevaLED® Area Value
Light Engines
Benefits
• 1100lm on 270 x 270mm
• 4500lm on 530 x 530mm
•
•
•
•
•
•
•
•
•
•
Efficacy: up to 141 lm/W
Homogeneous light distribution
Consistent white light of 4 SDCM
Poke-in connectors for 0,5mm² wire
No special connection cable needed
Self-cooling
Average lifetime 50.000h
SELV module for easier fixture design
UL, CE, VDE under approval
5 years system warranty in combination
with suitable OPTOTRONIC drivers
Applications
• Office (workplace illumination, corridor)
• Residential
Basic description*
Flux
(lm)
CCT
(K)
CRI
SDCM
If
(mA)
P (W)
Module
Tc 55°C
lm/W*
Module
Tc 55°C
L70 B50**
(h)
PLVG1-Ar-1100-830-270x270-DC
1057
3000
> 80
4
230
8
131
50.000
PLVG1-Ar-1100-840-270x270-DC
1138
4000
> 80
4
230
8
141
50.000
PLVG1-Ar-4500-830-530x530-DC
4196
3000
> 80
4
940
35
128
50.000
PLVG1-Ar-4500-840-530x530-DC
4519
4000
> 80
4
940
35
137
50.000
Product name
Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual
parameters of each single product which could differ from the typical data.
* Typical value; tolerance for optical and electrical data: +/-10%
**average Lifetime L70B50 (lumen maintenance) up to 50.000h at Tc = 55°C. Typical current 230mA for 1100lm and 975mA for 4500lm
Electrical parameters
Vf
(V)
If max
(mA)
P max
(W)
Flux
(lm)
lm/W*
Module
PLVG1-Ar-1100-830-270x270-DC
35
430
16
1833
115
PLVG1-Ar-1100-840-270x270-DC
35
430
16
1974
123
PLVG1-Ar-4500-830-530x530-DC
35
1440
53
6137
116
PLVG1-Ar-4500-840-530x530-DC
35
1440
53
6609
125
Product name
*
Performance data at Tc = 55°C
PrevaLED Area Value, April 2014
page 1 of 4
Minimum and Maximum Ratings
Product
Storage
temperature [ °C ]
Tc max.*
(@ typ. current)
L80 B50 @
Tc max. 85°C
-30 … +80
85°C
tbd h
PLVG1-AR-xx00-8x0-xxx-DC
The modules are designed for operation with OTp OPTOTRONIC® ECG.
*) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the light engine. The temperature of the LED module must be measured at the
tc-point according to EN60598-1 in thermally settled conditions with a temperature sensor. For exact location of the Tc -point see drawing below.
Drawings
PLVG1-Ar-1100-8x0-270x270-DC
All dimensions:
General tolerances:
PrevaLED Area Value, April 2014
mm
+/-0.15 if not specified
page 2 of 4
PLVG1-Ar-4500-8x0-530x530-DC
All dimensions:
General tolerances:
PrevaLED Area Value, April 2014
mm
+/-0.15 if not specified
page 3 of 4
Safety Information

The LED module itself and all its components must not be mechanically stressed.

When handling the module without use of mountain screws avoid excessive force on the cover as it may be separated from the PCB.

The integrated mounting and locking mechanism on the cover of the module is intended to center and lock a reflector. Excessive
force on this mechanism may cause permanent damage to the module.
The modules are intended for operation only with matching OPTOTRONIC® of OTp series.
To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be
ENEC certified. In Europe the declarations of conformity must include the following standards:
CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384.
Also check for the mark of an independent authorized certification institute.
Please see the relevant brochure for more detailed information (see "Related and Further Information")
OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation.

Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.

Pay attention to standard ESD precautions when installing the module.

Important information on photobiological safety is available in the application guide.

Eye Security EN 62471, Risk Group 1

Max. voltage U-OUT = 60V
Assembly Information

For optimum cooling a thermally conducting layer should be applied between module and heat sink.

Further details and recommendation for mounting can be found in the application guide.
Ordering codes
Product group
Product name
PrevaLED Area Value
PrevaLED Area Value
PrevaLED Area Value
PrevaLED Area Value
*) EAN: reservation
PLVG1-Ar-1100-830-270x270-DC
PLVG1-Ar-1100-840-270x270-DC
PLVG1-Ar-4500-830-530x530-DC
PLVG1-Ar-4500-840-530x530-DC
EAN *
S-Unit *
4052899 134478
4052899 134508
4052899 134539
4052899 134560
40 x 1
40 x 1
20 x 1
20 x 1
S-Unit: products per shipping unit (subject to change)
Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves.
Sales and Technical Support
OSRAM GmbH
Marcel-Breuer-Straße 6
D-80807 München
Germany
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
www.osram.com
+49 89 6213-0
Related and Further Information

PrevaLED® Application Guide
www.osram.com/prevaled-linear

OPTOTRONIC® Technical Guide
www.osram.com/ecg-downloads

OPTOTRONIC® Data Sheets
http://catalog.myosram.com
PrevaLED Area Value, April 2014
page 4 of 4