Preliminary Data Sheet EFFECTlight WL01B Benefits Picture for Datasheet is missing !!! ¾ Compact and powerful LED lightsource ¾ Extremely small viewing angle ¾ Available in various colors Applications ¾ Grazing angle accent lighting in architectural settings ¾ Signals without security requirements ¾ Specialized spot lighting Technical Operating Data Number of LEDs Voltage [V DC]* Power [W]* Current [A]* Radiance Angle [°]* Wavelength [nm] Color Temp [K]* Lum. Intensity [cd]* red 10 24 1,5 0,06 4 617 nm 3500 WL01B-Y1 yellow 10 24 1,5 0,06 4 587 nm 2750 WL01B-V1 verde 10 24 1,1 0,04 4 505 nm 2500 WL01B-B2 blue 10 24 1,1 0,04 4 469 nm 500 Product Color WL01B-A1 *) All Data are related to the entire module Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Technical Features ¾ Modules optimized for use with OSRAM ¾ Easily combined with supplementary optical OPTOTRONIC® power supplies. ¾ Dimmable by pulse width modulation (PWM) with the electronic controller OT DIM elements ¾ Extremely high light intensity ¾ High color saturation ¾ Parallel connection up to fourteen modules ¾ Easy connection with OSRAM CONNECTsystem LM-2x WL01B - 01.06.2006 - P Page 1 of 4 Minimum and Maximum Ratings Product Operating Temperature at Tc-Point [ °C ] * Storage Temperature [ °C ] * Voltage Range [ V dc ] * Reverse Voltage [ V dc ] * WL01B-A1 -30 ... 65 -40 ... 85 23 ... 25 25 WL01B-Y1 -30 ... 65 -40 ... 85 23 ... 25 25 WL01B-V1 -30 ... 65 -40 ... 85 23 ... 25 25 WL01B-B2 -30 ... 65 -40 ... 85 23 ... 25 25 *) Exceeding maximum ratings for operation and storage temperature will reduce expected life time or destroy the LED Module. Exceeding maximum ratings for operation voltage will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module needs to measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label (available e.g. at RS-Components). For exact location of the Tc-point see drawing below. Drawing Drawing is missing !!! WL01B - 01.06.2006 - P Page 2 of 4 Safety Information ¾ The LED module itself and all its components may not be mechanically stressed. ¾ Assembly must not damage or destroy conducting paths on the circuit board. The LED Module incorporates no protection against short circuits, overload or overheating. Therefore it is absolutely necessary to operate the modules with a electronically stabilised power supply offering protection against the above mentioned safety risks. For dimming applications attention should be paid to specific references in "OPTOTRONIC ® Technical Guide". OSRAM OPTOTRONIC ® power supplies are specifically designed with protection features for safe operation. When using power supplies other than OPTOTRONIC ® the following basic safety features are required, in addition to any other application specific concerns and local safety codes: ¾ Short circuit protection ¾ Overload protection ¾ Overheat protection ¾ Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. ¾ Correct electrical polarity needs to be observed. Wrong polarity will result in no light emission. ¾ Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and demage the LED module. ¾ Maximum of 14 modules can be connected together without supplemental power feed due to voltage drop and current carrying capacity. ¾ The EFFECTlight should be protected against UV- radiation in outdoor- applications. ¾ The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. ¾ Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. WL01B - 01.06.2006 - P Page 3 of 4 Assembly Information ¾ Solder connections should only be performed on designated solder pads (marked "24V +/-") using 0,5 mm² wires. During soldering, do not exceed the maximum soldering time of 10 seconds and the maximum soldering temperature of 260°C. ¾ EFFECTlight can be mounted by construction either a guide rail or clamping fixture which matches with the existing mounting groove of the module. ¾ Small scratches, bubbles or cavitations in lenses are production related and do not affect the optical functions of the EFFECTlight. ¾ Production related tolerances may cause a difference of the optical and mechanical axes. For sensitive applications there is important a possibility to adjust the modules by the fixture. Ordering Guide S-Unit * Productgroup Productname EAN * EFFECTlight WL01B-A1 4008321909855 10 EFFECTlight WL01B-Y1 4008321909862 10 EFFECTlight WL01B-V1 4008321909879 10 EFFECTlight WL01B-B2 4008321909886 10 *) EAN: Ordering number per single module S-Unit: Modules per shipping unit Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. Sales and Technical Support OSRAM GmbH Hellabrunner Strasse 1 D - 81536 München Germany www.osram.com +49 (0)89 6213-0 Sales and technical support is given by the local OSRAM subsidiaries. On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers. Related and Further Information ¾ The new dimension of light 153 S006 GB ¾ Webpages LED Systems http://www.osram.com/products/led-systems ¾ OPTOTRONIC® Technical Guide 130 T008 GB ¾ OPTOTRONIC® Technical Guide - Download: Electronic Control Gear - Handbook OPTOTRONIK® www.osram.com/service_corner/download_cen ter WL01B - 01.06.2006 - P Page 4 of 4