C200 2.5-Inch NAND Flash SSD

C200 2.5-Inch NAND Flash SSD
Features
C200 2.5-Inch SATA NAND Flash SSD
MTFDBAAxxxMAE
Features
•
•
•
•
•
•
•
•
•
•
•
•
• Reliability
– MTBF: 1 million device hours
– 3-year warranty
– Static and dynamic wear leveling
– Field-upgradable firmware
– Bit error rate: <1 sector per 1015 bits read
– Low power consumption: <2.5W active
• Endurance
– Total bytes written per drive density – 30GB:
21TB; 60GB: 42TB; 120GB: 85TB
• Mechanical
– Standard SATA connector: 5V ±5%
– 2.5-inch drive: 100.45mm x 69.85mm x 9.5mm
– Weight: 77g (MAX)
• Capacity3 (unformatted)
– 30GB
– 60GB
– 120GB
• Operating temperature
– Commercial (0°C to +70°C)
Micron® MLC NAND Flash
RoHS-compliant package
SATA 3 Gb/s interface
ATA modes supported
– PIO mode 3, 4
– Multiword DMA mode 0, 1, 2
– Ultra DMA mode 0, 1, 2, 3, 4, 5, 6
Industry-standard, 512-byte sector size support
Hot-plug capable
Native command queueing support with 32 command slot support
ATA-7 command set compliant
ATA security feature command set and password
login support
Secure erase (data page) command set: fast and secure erase (clear, sanitize)
Self-monitoring, analysis, and reporting technology
(SMART) command set
Performance1, 2
– Sequential READ: up to 170 MB/s
– Sequential WRITE: up to 70 MB/s (45 MB/s for
30GB drive)
– READ latency: 220µs (TYP)
– WRITE latency: 370µs (TYP)
Notes:
1. Typical I/O performance numbers as measured using Iometer with a queue depth of
32 and write cache enabled.
2. 4K transfers used for READ/WRITE latency
values.
3. 1GB = 1 billion bytes; formatted capacity is
less.
Warranty: Contact your Micron sales representative
for further information regarding the product,
including product warranties.
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
1
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
C200 2.5-Inch NAND Flash SSD
Features
Part Numbering Information
Micron’s C200 SSD is available in different configurations and densities. Visit www.micron.com for a list of valid
part numbers.
Figure 1: Part Number Chart
MT FD
B
AC xxx M AE - 1
Micron Technology
C
1
ES
Production Status
Blank = Production
Product Family
ES = Engineering sample
FD = Flash drive
MS = Mechanical sample
Drive Interface
Operating Temperature Range
B = SATA 3.0 Gb/s
Blank = Commercial (0°C to +70°C)
Drive Form Factor
AA = 1.8-inch Micro SATA HDD replacement (5mm)
BOM Revision
AC = 2.5-inch HDD replacement (9.5mm)
1 = 1st generation
NAND Flash Component
Drive Density
030 = 30GB
060 = 60GB
120 = 120GB
C = 16Gb, MLC, x8, 3.3 V, 50nm
Revision Control
1 = 1st generation
NAND Flash Type
Product Family
M = MLC
AE = x200
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
General Description
General Description
Micron’s solid state drive (SSD) uses a single-chip controller with a SATA interface on
the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD
replacement enclosure, the SSD integrates easily in existing storage infrastructures.
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability.
Figure 2: Functional Block Diagram
NAND
SATA
SSD
controller
NAND
NAND
NAND
NAND
DRAM
buffer
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Architecture
Architecture
The 200-series SSD is a NAND Flash storage device. A SATA 3 Gb/s interface connects to
the SSD externally and communicates with the controller. The controller manages data
transfers to and from the NAND Flash array.
Table 1: C200 Configurations
Unformatted Disk
Density
NAND Flash Process NAND Flash Density
Package Count
Die per TSOP Package
30GB
50nm
16Gb
16
1
60GB
50nm
16Gb
16
2
120GB
50nm
16Gb
16
4
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure
sufficient storage space for the specified density. Standard LBA settings, based on the
IDEMA standard (LBA1-02), are shown below.
Table 2: Standard LBA Settings
Total LBAs
Drive Size1
Max LBA
User Available Bytes
Decimal
Hexadecimal
Decimal
Hexadecimal
(Unformatted)
30GB
58,626,288
37E90F0
58,626,287
37E90EF
30,016,659,456
60GB
117,231,408
6FCCF30
117,231,407
6FCCF2F
60,022,480,896
120GB
234,441,648
DF94BB0
234,441,647
DF94BAF
120,034,123,776
Note:
1. 1GB = 1,000,000,000 bytes.
Table 3: 2.5-Inch Nominal Dimensions and Weight
Value
Unit
Height
9.5
mm
Width
69.85
mm
Length
100.45
mm
77
g
Unit weight
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Architecture
Interface Connectors
The SATA signal segment interface cable has four conductors and three ground connections. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a
power segment arranged in a single row with a 1.27mm (0.050in) pitch.
Table 4: Micro SATA Signal Segment Pin Assignments
Signal Name
Type
Description
S1
GND
Ground
S2
A
Differential signal pair
S3
A#
A and A#
S4
GND
S5
B#
Differential signal pair
S6
B
B and B#
S7
GND
Ground
Ground
Table 5: 2.5-Inch Micro SATA Power Segment Pin Assignments
Pin#
Signal Name
Description
P1
V33
No connect
P2
V33
No connect
P3
V33
No connect
P4
GND
Ground
P5
GND
Ground
P6
GND
Ground
P7
V5
5V power, precharge
P8
V5
5V power
P9
V5
5V power
P10
GND
Ground
P11
DAS1
Device activity signal
P12
GND
Ground
P13
V12
No connect
P14
V12
No connect
P15
V12
No connect
Note:
1. The DAS signal may be optionally connected to GND if an LED is not being used.
Figure 3: Micro SSD Interface Connections
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
5
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Architecture
P1
S1
Power
segment
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
Signal
segment
6
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Device ID
Table 6: IDENTIFY Device ID
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
0
15
F
0b
0 = ATA device
14–8
X
X
Retired
7
F
0b
0 = Non-removable media device
6–3
X
X
Don’t Care
2
V
0/1b
1
X
X
Retired
1 = IDENTIFY DEVICE data incomplete
0
F
0b
Reserved
1
15–0
X
X
Number of logical cylinders (obsolete)
2
15–0
V
X
Specific configuration (obsolete)
3
15–0
X
X
Number of logical heads (obsolete)
4–5
31–0
X
X
Number of logical sectors per logical track (obsolete)
6
15–0
X
X
Reserved
7–8
31–0
V
X
Reserved
9
15–0
X
X
Retired
10–19 159–0
F
Varies
20–22 47–0
X
X
23–26 63–0
F
Varies
Firmware revision (8 ASCII characters)
27–46 319–0
F
Varies
Model number (40 ASCII characters)
47
Serial number (20 ASCII characters)
Don’t Care
15–8
F
80h
80h
7–0
F
10h
00h = Reserved
01h-FFh = Number of sectors transfered per interrupt on R/W MULTIPLE cmds
48
15–0
F
0h
Reserved
49
15–14
R
00b
Reserved for IDENTIFY PACKET DEVICE cmd
13
F
1b
1 = Standby timer values as specified in ATA/ATAPI - 7 support
0 = Standby timer values shall be managed by the device
12
R
0b
Reserved for IDENTIFY PACKET DEVICE cmd
11
F
1b
1 = IORDY support
0 = IORDY may be supported
10
F
1b
1 = IORDY may be disabled
9
F
1b
1 = LBA support
8
F
1b
1 = DMA support
7–0
X
X
Retired
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
50
15
F
0b
Shall be cleared to 0
14
F
1b
Don’t Care (set to 1)
13–2
F
0h
Reserved
1
X
X
Obsolete
0
F
0b
1 = Device specific standby timer min value
X
X
Obsolete
15–3
R
0h
Reserved
2
F
1b
1 = The fields reported in word 88 are valid
0 = The fields reported in word 88 are not valid
1
F
1b
1 = The fields reported in words (70:64) are valid
0 = The fields reported in words (70:64) are not valid
0
X
X
Obsolete
54
15–0
X
X
Number of current cylinders (obsolete)
55
15–0
X
X
Number of current heads (obsolete)
56
15–0
X
X
Numer of current sectors per track (obsolete)
57–58 31–0
X
X
Current capacity in sectors (obsolete)
15–9
F
0h
Reserved
8
V
X
1 = Multiple sector setting is valid (Don’t Care)
7–0
V
X
xxh = Current setting for number of sectors per interrupt on R/W MULTIPLE cmds
60–61 31–0
F
Sect
51–52 31–0
53
59
Total number of user addressable sectors (28-bit address)
62
15–0
X
X
Obsolete
63
15–11
F
0h
Reserved
10
V
0/1b
1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
9
V
0/1b
1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
8
V
0/1b
1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
7–3
F
0h
Reserved
2
F
1b
1 = Multiword DMA mode 2 and below is supported
1
F
1b
1 = Multiword DMA mode 1 and below is supported
0
F
1b
1 = Multiword DMA mode 0 is supported
64
15–2
F
0h
Reserved
1–0
F
3h
PIO modes support
65
15–0
F
78h
Minimum multiword DMA transfer cycle time per word in nanoseconds
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
8
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
66
15–0
F
78h
MFR recommended multiword DMA transfer cycle time per word in nanoseconds
67
15–0
F
78h
Minimum PIO transfer cycle time without IORDY flow control
68
15–0
F
78h
Minimum PIO transfer cycle time with IORDY flow control
69–74 95–0
F
0h
Reserved
75
15–5
F
0h
Reserved
4–0
F
1Fh
1Fh = NCQ device (1Fh = 32 - 1 [maximum queue depth support])
15–13
F
0h
Reserved
12
F
0b
1 = Supports NCQ priority information
11
F
0b
1 = Supports unload while NCQ commands outstanding
10
F
0b
1 = Supports phy event counters
9
F
0b
1 = Supports receipt of host-initiated power management requests (HIPM)
8
F
1b
1 = Supports native command queuing (NCQ)
7–3
F
0h
Reserved
2
F
1b
1 = Supports Serial ATA Gen-2 signaling speed (3 Gb/s)
1
F
1b
1 = Supports Serial ATA Gen-1 signaling speed (1.5Gb/s)
0
F
0b
Reserved
77
15–0
F
0h
Reserved
78
15–7
F
0h
Reserved
6
F
1b
1 = Supports software settings preservation
5
F
0b
Reserved
4
F
0b
1 = Supports in-order data delivery
3
F
1b
1 = Device supports initiating interface power management (DIPM)
2
F
0b
1 = Supports DMA Setup auto-activate optimization
1
F
0b
1 = Supports nonzero buffer offsets in DMA Setup FIS
76
79
0
F
0b
Reserved
15–7
F
0h
Reserved
6
V
1b
1 = Software settings preservation enabled
5
F
0b
Reserved
4
V
0b
1 = In-order data delivery enabled
3
V
0b
1 = Device initiating interface power management enabled
2
V
0b
1 = DMA setup auto-activate optimization enabled
1
V
0b
1 = Nonzero buffer offsets in DMA setup FIS enabled
0
F
0b
Reserved
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
9
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
80
15–9
F
0h
Major version number reserved (future revisions)
8
F
0b
Reserved for ATA/ATAPI-8 major version number
7
F
1b
1 = Supports ATA/ATAPI-7 major version number
6
F
1b
1 = Supports ATA/ATAPI-6 major version number
5
F
1b
1 = Supports ATA/ATAPI-5 major version number
4
F
1b
1 = Supports ATA/ATAPI-4 major version number
3–1
X
X
Obsolete
0
F
0b
Reserved
Minor version number
81
15–0
F
21h
82
15
X
X
Obsolete
14
F
1b
1 = NOP command support
13
F
1b
1 = READ BUFFER command support
12
F
1b
1 = WRITE BUFFER command support
11
X
X
Obsolete
10
F
1b
1 = Host-protected area feature set support
9
F
0b
1 = DEVICE RESET command support (ATAPI packet command)
8
F
0b
1 = Service interrupt support
7
F
0b
1 = Release interrupt support
6
F
1b
1 = Look-ahead support
5
F
1b
1 = Write cache support
4
F
0b
1 = Packet command feature set support
3
F
1b
1 = Mandatory power management feature set support
2
F
0b
1 = Removable media feature set support
1
F
1b
1 = Security mode feature set support
0
F
1b
1 = SMART feature set support
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
10
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
83
84
15
F
0b
Shall be cleared to 0
14
F
1b
Shall be set to 1
13
F
1b
1 = FLUSH CACHE EXT command support
12
F
1b
1 = Mandatory FLUSH CACHE command support
11
F
1b
1 = Device configuration overlay feature set support
10
F
1b
1 = 48-bit address feature set support
9
F
0b
1 = Automatic acoustic management feature set support
8
F
1b
1 = SET MAX security extension support
7
F
0b
1 = Address offset reserved area boot mode support
6
F
X
1 = SET FEATURES subcommand required by HDD will be non-op to an SSD
5
F
1b
1 = Power-up in standby feature set support
4
F
0b
1 = Removable media status notification feature set support
3
F
X
1 = Advanced power management feature set support
2
F
0b
1 = CFA feature set support
1
F
0b
1 = READ/WRITE DMA QUEUED support
0
F
1b
1 = DOWNLOAD MICROCODE command support
15
F
0b
Shall be cleared to 0
14
F
1b
Shall be set to 1
13
F
0b
1 = IDLE IMMEDIATE with UNLOAD FEATURE support
12
F
X
Reserved for technical report INCITS TR-37-2004 (TLC)
11
F
X
Reserved for technical report INCITS TR-37-2004 (TLC)
10
F
0b
1 = URG bit support for WRITE STREAM DMA EXT and WRITE STREAM EXT
9
F
0b
1 = URG bit support for READ STREAM DMA EXT and READ STREAM EXT
8
F
X
1 = 64-bit worldwide name support
7
F
0b
1 = WRITE DMA QUEUED FUA EXT command support
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands support
5
F
1b
1 = General purpose logging feature set support
4
F
0b
1 = Streaming feature set support
3
F
0b
1 = Media card passthrough command feature set support
2
F
0b
1 = Media serial number support
1
F
1b
1 = SMART self-test support
0
F
1b
1 = SMART error logging support
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
11
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
85
86
15
X
X
Obsolete
14
F
1b
1 = NOP command enabled
13
F
1b
1 = READ BUFFER command enabled
12
F
1b
1 = WRITE BUFFER command enabled
11
X
X
Obsolete
10
V
1b
1 = Host-protected area feature set enabled
9
F
0b
1 = DEVICE RESET command enabled (ATAPI packet command)
8
V
0b
1 = SERVICE interrupt enabled
7
V
0b
1 = Release interrupt enabled
6
V
1b
1 = Look-ahead enabled
5
V
1b
1 = Write cache enabled
4
F
0b
1 = Packet command feature set enabled
3
F
1b
1 = Power management feature set enabled
2
F
0b
1 = Removable media feature set enabled
1
V
0b
1 = Security mode feature set enabled
0
V
1b
1 = SMART feature set enabled
15
F
1b
1 = Words 120 and 119 are valid
14
F
0b
Reserved
13
F
1b
1 = FLUSH CACHE EXT command supported
12
F
1b
1 = Mandatory FLUSH CACHE command support
11
F
1b
1 = Device configuration overlay feature set support
10
F
1b
1 = 48-bit address feature set support
9
V
0b
1 = Automatic acoustic management feature set enabled
8
F
0b
1 = SET MAX security extension enabled by SET MAX SET PASSWORD
7
F
0b
1 = Address offset reserved area boot mode active
6
F
X
1 = SET FEATURES subcommand required on HDD and is Non-Op for an SSD
5
V
0b
1 = Power-up in standby feature set enabled
4
V
0b
1 = Removable media status notification feature set enabled
3
V
0b
1 = Advanced power management feature set enabled
2
F
0b
1 = CFA feature set enabled
1
F
0b
1 = READ/WRITE DMA QUEUED support
0
F
1b
1 = DOWNLOAD MICROCODE command support
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
12
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
87
15
F
0b
Shall be cleared to 0
14
F
1b
Shall be set to 1
13
F
0b
1 = IDLE IMMEDIATE with UNLOAD FEATURE support (default)
12
F
X
Reserved for technical report INCITS TR-37-2004 (TLC)
11
F
X
Reserved for technical report INCITS TR-37-2004 (TLC)
10
F
0b
1 = URG bit for WRITE STREAM DMA EXT & WRITE STREAM EXT (sup. Dflt.)
9
F
0b
1 = URG bit for READ STREAM DMA EXT & READ STREAM EXT (sup. Dflt.)
8
F
X
1 = 64-bit worldwide name support (default)
7
F
0b
1 = WRITE DMA QUEUED FUA EXT command support (default)
6
F
1b
1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT cmds support (default)
5
F
1b
1 = General purpose logging feature set support (default)
4
V
0b
1 = Streaming feature set support (default)
3
V
0b
1 = Media card passthrough command feature set support (default)
2
V
0b
1 = Media serial number support (default)
1
F
1b
1 = SMART self-test support (default)
0
F
1b
1 = SMART error logging support (default)
15
F
0b
Reserved
14
F
0b
Reserved
13
V
0/1b
1 = Ultra DMA mode 5 is selected0 = Ultra DMA mode 5 is not selected
12
V
0/1b
1 = Ultra DMA mode 4 is selected0 = Ultra DMA mode 4 is not selected
11
V
0/1b
1 = Ultra DMA mode 3 is selected0 = Ultra DMA mode 3 is not selected
10
V
0/1b
1 = Ultra DMA mode 2 is selected0 = Ultra DMA mode 2 is not selected
9
V
0/1b
1 = Ultra DMA mode 1 is selected0 = Ultra DMA mode 1 is not selected
8
V
0/1b
1 = Ultra DMA mode 0 is selected0 = Ultra DMA mode 0 is not selected
7
F
0b
Reserved
6
F
X
1 = Ultra DMA mode 6 and below supported
5
F
1b
1 = Ultra DMA mode 5 and below supported
4
F
1b
1 = Ultra DMA mode 4 and below supported
3
F
1b
1 = Ultra DMA mode 3 and below supported
2
F
1b
1 = Ultra DMA mode 2 and below supported
1
F
1b
1 = Ultra DMA mode 1 and below supported
0
F
1b
1 = Ultra DMA mode 0 support
89
15–0
F
5h
Time required; Security erase unit complete
90
15–0
F
5h
Time required; Enhanced security erase complete
88
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
13
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Device ID
Table 6: IDENTIFY Device ID (Continued)
• F = The content of the word is fixed and does not change
• V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device
• X = The content of the word may be fixed or variable
• R = The content of the word is reserved and shall be zero
Word Bit(s) Setting Default Value Description
91
15–0
V
0h
92
15–0
V
0h or FFFFh
Current advanced power management value
93
15–0
V
0h
Cleared to 0s if Serial ATA
94
15–8
V
X
Vendor's recommended acoustic management value
Master password revision code
7–0
V
0h
Current auto acoustic management value
95–99 79–0
F
X
Reserved
100–
103
63–0
V
LBA
104– 367–0
126
F
X
Reserved
127
15–0
F
0h
Removable media bits
128
15–9
F
X
Security status bits
8
V
X
1 = Security mode enabled
7–6
R
X
Security status bits
5
V
0b
1 = Enhanced security erase unit support
4
V
X
1 = Security count is expired
3
V
X
1 = Security frozen
2
V
X
1 = Security locked
1
V
X
1 = Security enabled
0
F
1h
1 = Security supported
129– 2015–
254
0
F
X
Reserved
255
15–8
X
X
Checksum
7–0
X
A5h
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
Maximum user LBA for 48-bit address feature set
A5h = Signature for ATA device
14
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Commands
Commands
Table 7: Supported ATA Command Set
See ATA-7 standard for command details
Command Name
Command Code (hex)
CHECK POWER MODE
98h or E5h
DEVICE CONFIGURATION RESTORE
B1h/C0h
DEVICE CONFIGURATION FREEZE LOCK
B1h/C1h
DEVICE CONFIGURATION IDENTIFY
B1h/C2h
DEVICE CONFIGURATION SET
B1h/C3h
DOWNLOAD MICROCODE
92h
EXECUTE DEVICE DIAGNOSTIC
90h
FLUSH CACHE
E7h
FLUSH CACHE EXT
EAh
IDENTIFY DEVICE
ECh
IDLE
E3h or 97h
IDLE IMMEDIATE
E1h or 95h
INITIALIZE DEVICE PARAMETERS
91h
NOP
00h
READ BUFFER
E4h
READ DMA (with retry)
C8h
READ DMA (without retry)
C9h
READ DMA EXT
25h
READ FPDMA QUEUED
60h
READ LOG EXT
2Fh
READ MULTIPLE
C4h
READ MULTIPLE EXT
29h
READ NATIVE MAX ADDRESS
F8h
READ NATIVE MAX ADDRESS EXT
27h
READ SECTOR(S) EXT
24h
READ SECTOR(S) (with retry)
20h
READ SECTOR(S) (without retry)
21h
READ VERIFY SECTOR EXT
42h
READ VERIFY SECTOR(S) (with retry)
40h
SECURITY DISABLE PASSWORD
F6h
SECURITY ERASE PREPARE
F3h
SECURITY ERASE UNIT
F4h
SECURITY FREEZE LOCK
F5h
SECURITY SET PASSWORD
F1h
SECURITY UNLOCK
F2h
SEEK
7xh
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
15
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Commands
Table 7: Supported ATA Command Set (Continued)
See ATA-7 standard for command details
Command Name
Command Code (hex)
SET FEATURES
EFh
SET MAX ADDRESS
F9h
SET MAX – FREEZE LOCK
F9h/04h
SET MAX – LOCK
F9h/02h
SET MAX ADDRESS EXT
37h
SET MULTIPLE MODE
C6h
SET MAX – SET PASSWORD
F9h/01h
SET MAX – UNLOCK
F9h/03h
SLEEP
E6h or 99h
SMART DISABLE OPERATIONS
B0h/D9h
SMART ENABLE OPERATIONS
B0h/D8h
SMART ENABLE/DISABLE AUTOSAVE
B0h/D2h
SMART EXECUTE OFF-LINE IMMEDIATE
B0h/D4h
SMART READ DATA
B0h/D0h
SMART READ LOG SECTOR
B0h/D5h
SMART RETURN STATUS
B0h/DAh
SMART WRITE LOG
B0h/D6h
STANDBY
E2h or 96h
STANDBY IMMEDIATE
E0h or 94h
WRITE BUFFER
E8h
WRITE DMA (with retry)
CAh
WRITE DMA (without retry)
CBh
WRITE DMA EXT
35h
WRITE DMA FUA EXT
3Dh
WRITE FPDMA QUEUED
61h
WRITE LOG EXT
3Fh
WRITE MULTIPLE
C5h
WRITE MULTIPLE EXT
39h
WRITE MULTIPLE FUA EXT
CEh
WRITE SECTOR(S) (with retry)
30h
WRITE SECTOR(S) EXT
34h
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
16
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Reliability
Reliability
Micron’s SSDs incorporate advanced technology for defect and error management.
They use various combinations of hardware-based error correction algorithms and
firmware-based static and dynamic wear-leveling algorithms.
Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read
out of the SSD, the data differs from what was programmed.
Table 8: Uncorrectable Bit Error Rate
Uncorrectable Bit Error Rate
Operation
1015
READ
<1 sector per
bits read
Mean Time Between Failures
Mean time between failures (MTBFs) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability
prediction procedures for electronic equipment.
Table 9: MTBFs
Density
MTBF (Operating Hours)
30GB
1 million
60GB
1 million
120GB
1 million
Endurance
Endurance for the SSD can be predicted based on the usage conditons applied to the
device, the internal NAND component cycles, the write amplification factor, and the
wear-leveling efficency of the drive. The table below shows the drive lifetime for each
SSD density based on predefined usage conditions.
Table 10: Drive Lifetime
Density
Notes:
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
Drive Lifetime (Total Bytes Written)
30GB
21TB
60GB
42TB
120GB
85TB
1. Total bytes written calculated with the drive 90% full.
2. Access patterns consist of the following: 5% are 4k; 5% are 8k; 10% are 16k; 10% are
32k; 35% are 64K; and 35% are 128k.
3. GB/day can be calculated by dividing the total bytes written value by (365 × number of
years).
17
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Electrical Characteristics
Electrical Characteristics
Table 11: SATA Typical Power Consumption1
Density
Idle3
Sleep3
Standby3
Erase
Read2
Write2
Unit
30GB
0.116
0.116
0.116
2.5
1.6
2.5
W
60GB
0.116
0.116
0.116
2.5
1.6
2.5
W
120GB
0.116
0.116
0.116
2.5
1.6
2.5
W
1. Data taken at 25°C.
2. IOMETER MAX transfer rate with 128KB transfer size.
3. DIPM enabled.
Notes:
Table 12: Absolute Maximum Ratings
Parameter/Condition
Symbol
Min
Max
Unit
Voltage input
V5
4.75
5.25
V
Voltage input
V33
–0.5
+3.96
V
TA
0
70
°C
Nonoperating temperature
–55
+95
°C
Rate of temperature change
–
+20
°C/hour
Relative humidity (noncondensing)
5
95
%
Operating temperature
Commercial
Stresses greater than those listed may cause permanent damage to the device. This is a
stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
reliability.
Table 13: Shock and Vibration
Parameter/Condition
Specification
Operating shock
1500 G/1.0ms
Operating vibration
2–500Hz at 3.1G
Table 14: Recommended Operating Conditions
Parameter/Condition
Power supply voltage
Ground supply voltage
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
18
Symbol
Min
Typ
Max
Unit
V5
4.75
5.0
5.25
V
GND
0
0
0
V
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Compliance
Compliance
Micron SSDs comply with the following:
•
•
•
•
•
•
•
•
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
RoHS “green”
CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003
FCC: CFR Title 47, Part 15, ICES-003, all Class B
UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition
BSMI (Taiwan): Appproval to CNS 13438
TUV/GS (Germany): Approval to IEC60950/EN6095
VCCI
W.E.E.E.
19
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
Package Dimensions
Package Dimensions
Figure 4: 2.5-Inch Package (Preliminary)
69.85mm ±0.25
2.750in ±0.010
61.72mm
2.430in
bottom side
4.07mm
0.160in
bottom side
D and T M3 x 0.5
bottom side
1.52mm
0.060in
3.50mm ±0.38
0.138in ±0.015
0.25mm
0.010in
TYP con
clearance
100.45mm
3.955in
90.60mm
3.567in
bottom side
14.00mm
0.551in
bottom
side
3.0mm RAD
0.12in
3.43mm
0.529in
+0.00
9.50mm -0.50
+0.000
0.374in -0.020
B
0.30mm
0.012in
90.60mm
3.567in
14.00mm
0.551in
3.00mm
0.118in
Note:
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
Detail B
4.75mm
0.187in
D and T M3 x 0.5
bottom side
1. All dimensions are in millimeters.
20
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.
C200 2.5-Inch NAND Flash SSD
References
References
• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available
at www.sata-io.org
• SATA 3.0 GOLD
• ATA-8 ACS2
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
www.micron.com/productsupport Customer Comment Line: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur.
PDF: 09005aef836873c9
c200_2_5.pdf - Rev. C 9/09 EN
21
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2007 Micron Technology, Inc. All rights reserved.