7/16 DIN Male Right Angle Connector Clamp/ Solder Attachment For 1/2 inch Helical TECHNICAL DATA SHEET PE44559 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Helical Configuration Connector Connector Specification Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style 7/16 DIN Male IEC60169-4 1/2 inch Helical Clamp/Solder Right Angle Electrical Specifications Frequency Range, GHz Impedance, Ohms Maximum Return Loss, dB Maximum Operating Voltage, Volts DC to 3 50 28 2,700 Frequency 1 Frequency, GHz Insertion Loss, dB Power Handling, Watts DC to 2 0.05 400 Mechanical Specifications Temperature Operating Range, deg C -40 to +85 Size Length, in [mm] Width/Dia., in [mm] Height, in [mm] 2.2 [55.88] 1.36 [34.54] 1.77 [44.96] Weight, lbs [Kg] 9 [4.08] Connector Type Contact Material and Plating Contact Plating Specification Hex Size, in Body Material and Plating Body Plating Specification Dielectric Type 7/16 DIN Male Brass, Silver 5µ in. Minimum 1 1/4 Brass, Tri-Metal 3µ in. Minimum PTFE . Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Helical PE44559 PE44559 REV 01 1 7/16 DIN Male Right Angle Connector Clamp/ Solder Attachment For 1/2 inch Helical TECHNICAL DATA SHEET PE44559 Plotted and Other Data Notes: Values at 25 °C, sea level 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Helical from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Helical PE44559 URL: http://www.pasternack.com/7-16-male-standard-1-2-inch-helical-connector-pe44559-p.aspx PE44559 REV 01 2 © 2013 Pasternack Enterprises All Rights Reserved SCREW CLAMP NUT ONTO CABLE UNTIL EDGES OF NUT & OUTER CONDUCTOR ARE FLAT. SLIDE O-RING OVER THREAD AND SEAT INTO PLACE. GREASE O-RING. HOLD CLAMP NUT STEADY & SCREW BODY TIGHTLY ONTO CABLE. 4. 5. PUT THE SCREW GASKET ONTO CABLE, PAY ATTENTION TO THE CORRECT DIRECTION OF THE SCREW GASKET (ANGLE DIRECTION TOWARDS THE FRONT). WIPE THE GASKET WITH GREASE. 2. 3. STRIP CABLE AS SHOWN, CHAMFER CENTER CONDUCTOR & DEBURR CABLE. 1. ASSEMBLY PROCEDURES PE44559 REV 01 FSCM NO. 53919 PE44559 DWG TITLE CAD FILE 091208 SCALE N/A SIZE A 127 NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Helical PE44559 CAD Drawing 3