D50100CDM LED DOT MATRIX MODEL : SSD-D50100CDM Seoul Semiconductor Co., Ltd. 148-29,Kasan-Dong, KeumChun-Ku, Seoul, Korea TEL : 82-2-3281-6269 FAX:82-2-858-5537 Web-site : www.seoul-semicon.co.kr 1.특성 (FEATURES) RED, GREEN, AMBER COLOR 50.0 * 100.0 (mm) DIMENSION (mm) NUMBER OF DOT 512 Dynamic Drive (1/16 Duty) Drive mode 2.전기광학적 특성(ELECTRICAL & OPTIOCAL SPECIFICATION) (Ta=25° C) Unit Symbol Red Green Power dissipation PD 7.37 7.37 W Foward current IF 30 30 mA Peak foward current * IFP 60 60 mA Reverse voltage VR 5 5 V Parameter Operating temperature Topr -10 ~ +60 °C Operating temperature Tstg -20 ~ +70 °C * Conditions: Duty ratio≤1/10, I FP = 60mA * I FP conditions: Pulse width Tw≤0.1ms, Duty ratio≤1/10 (Ta=25 C) Parameter Red Condition Symbol - Green Min Typ Max Min Typ Max FORWARD Voltage IF =20mA VF - Reverse current V R =5V IF - Wavelength IF =20mA λp - Spectral bandwidth IF =20mA ∆λ - 2.0 2.4 - Unit - - - - - - V 10 - - - µA 2.1 2.4 10 - - 635 - - 573 - - - - nm 30 - - 30 - - - - nm 제품명 SSD-D50100CDM 발행일 04.01.26 3. 최적 동작 조건(RECOMMENABLE OPERATING CONDITION) ITEM (Ta=25° C) SYMBOL TYP. UNIT SUPPLY VOLTAGE V cc 5.0 V OPERATING AMBIENT TEMPERATURE T opr -10 ~ +60 ℃ 4. 광학적 특성(OPTICAL SPECIFICATION) (Ta=25 C) ITEM SYMBOL MIN. TYP. MAX. UNIT LUMINOUS INTENSITY RED GREEN Lv - 225 225 - cd/m WAVELENGTH RED GREEN λD - 635 573 - nm - deg VIEWING ANGLE * RED GREEN 2O 1/2 - 160 160 2 * Θ½ is the off-axis where the luminous intensity is 1/2 the peak intensity 5. 외형도(OUT LINE DRAWING) CN1 INPUT < VIEW OF BOTTOM > 제품명 SSD-D50100CDM 발행일 04.01.26 6. 핀 배열 (PIN ASSIGNS) INPUT SIGNAL(CN1) NO SIGNAL NAME 1 OUTPUT SIGNAL(CN2) POWER(CN3) SIGNAL NAME NO SIGNAL NAME NO RED DATA 1 RED DATA 1 GND 2 CLOCK 2 CLOCK 2 GND 3 LATCH 3 LATCH 3 VLED 4 A0 4 A0 4 VCC 5 A1 5 A1 5 VCC 6 A2 6 A2 7 A3 7 A3 8 ENABLE 8 ENABLE 9 GREEN DATA 9 GREEN DATA 10 GROUND 10 GROUND NO 1 2 3 CONNECTOR NAME INPUT SIGNAL (CN1) OUTPUT SIGNAL(CN2) POWER(CN3) MAKER YEONHO YEONHO YEONHO TYPE NO. 12505WS-10 12505WS-10 YW396-06V QTY 1 1 1 * 주의! 핀순서에 주의요망 (MIND THE PIN ORDER) 7. 신호선 접속(SIGNAL CABLE CONNECTION) INTERFACE CIRCUIT 1) DATA 진행방향 (DYNAMIC MODULE 적용) MODULE 4 MODULE 3 MODULE 2 MODULE 1 ( FRONT VIEW ) 제품명 발행일 SSD-D50100CDM 04.01.26 8. 타이밍 챠트 (TIMMING CHART) 1 2 3 4 15 16 +5V CLOCK 0V +5V SERIAL IN 0V +5V LATCH 0V +5V ENALBE 0V ON OUT 0 OFF ON OUT 1 OFF ON OUT 2 OFF ON OUT 15 OFF +5V SERIAL OUT 0V (NOTE) Latches are level sensitive (not edge triggerde). LATCH-terminal = H level, latches become transparent; LATCH-terminal = L level, latches hold data. ENABLE-terminal = H level, all outputs (OUT0-15) are off. SERIAL-OUT changes state on the falling edges of clock. Recommended Operating Condition CHARACTERISTIC UNIT SYMBOL CONDITION MIN. TYP. MAX. Supply Voltage VDD - 4.5 5.0 5.5 V Output Voltage VOUT - - - 9 V IO OUTn 5 - 115 IOH SERIAL OUT - - 1.0 OIL SERIAL OUT - - -1.0 VIH - 0.7VDD 0.7VDD VDD+0.3 VIL - -0.3 -0.3 0.3VDD 15 - - ns 15 - - ns 20 - - ns thold(D) 20 - - ns tsetup(L) 15 - - ns - - 25 MHz Output Current Input Voltage LATCH Pulse Width CLOCK Pulse Width Set up Time for DATA Hold Time for DATA Set up Time for LATCH Clock Frequency tw LAT tw CLK tsetup(D) fCLK VDD = 4.5 ~ 5.5 V Cascade operation 제품명 SSD-D50100CDM mA V 발행일 04.01.26 9. 블럭도 ( BLOCK DIAGRM ) DECODER DRIVER COMMON DRIVER RED, GREEN DOT MATRIX (16*16) SEGEMENT& CURRENT CONTROL DRIVER 16BIT DATA LATCH 16BIT SHIFT REGISTER 제품명 SSD-D50100CDM 발행일 04.01.26 11. 취급및 설치시 주의사항 (SAFETY) - 입력 범위 이상의 전원이나 역전압이 LED MODULE에 유입될시는 내부회로 가 손상되오니 입력전압 범위를 반드시 지켜주시기 바랍니다. - Backward voltage or overvoltage flows in the LED module can damage the internal circuits. Please operate the module under the permitted scope of voltage supply. - 높은 습도나 누수에 의해 LED MODULE의 고장 원인이 될수 있읍니다. - High humidity and leak can damage LED module. - DISPLAY PANEL의 수가 많을경우 및 배기시설이 양호하지 않을 경우에는 LED 발열에의한 MODULE의 손상과 오동작이 발생될수 있으므로 필요시 COOLING FAN을 설치하시기 바랍니다. - Install a cooling fan for cooling out the LED module in order to avoid damage or operateing failure caused by the heat when many display panels are attached to one board or the module is operated under ill-ventilated conditions. - LED DOT MATRIX MODULE에 충격및 진동을 가할 경우 DOT불량, 단선등의 원인이 될수 있으므로 삼가하여 주시기 바랍니다. - LED Module could be damaged or broken by a shock or collision. - LED MODULE에 찍힘이나 긁힘이 발생하지 않도록 주의하시기 바랍니다. - Be careful not to scratch or impact the LED Module. - MODULE을 취급, 보관할경우 정전기 방지 포장을 하여 주십시요. - Treat or keep under the condtion of static electricity-proof packing. - Twiste cable 또는 Shield wire는 고주파 잡음으로 부터 module을 보호 하여 안정된 동작을 할수 있으므로 필히 사용 하십시요. - It is recommended to use twist cable or shielded wire to protect the module from high-freqiency nosie and to secure stable operation. 제품명 SSD-D50100CDM 발행일 04.01.26