a FEATURES 10-Bit, 100 MSPS ADC Low Power: 450 mW at 100 MSPS On-Chip Track/Hold 280 MHz Analog Bandwidth SINAD = 54 dB @ 41 MHz On-Chip Reference 1 V p-p Analog Input Range Single 5 V Supply Operation 5 V/3.3 V Outputs APPLICATIONS Digital Communications Signal Intelligence Digital Oscilloscopes Spectrum Analyzers Medical Imaging Sonar HDTV GENERAL DESCRIPTION The AD9071 is a monolithic sampling analog-to-digital converter with an on-chip track-and-hold circuit and TTL/CMOS digital interfaces. The product operates at a 100 MSPS conversion rate with outstanding dynamic performance over its full operating range. The ADC requires only a single 5 V supply and an encode clock for full performance operation. The digital outputs are TTL compatible. Separate output power supply pins support 10-Bit, 100 MSPS A/D Converter AD9071 FUNCTIONAL BLOCK DIAGRAM VREF OUT VREF IN VCC – 2.5V AD9071 VDD AIN ADC T/H AIN SUM AMP DAC 10 D0–D9 ENCODE LOGIC OR ADC ENCODE TIMING VCC GND interfacing with 3.3 V or 5 V logic. An out-of-range output (OR) is available that indicates a conversion result is outside the operating range. The output data are held at saturation levels during an out-of-range condition. The input amplifier supports differential or single-ended interfaces. An internal reference is included. Fabricated on an advanced BiCMOS process, the AD9071 is available in a plastic SOIC package specified over the industrial temperature range (–40°C to +85°C). REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2001 (VCC = 5 V, VDD = 3.3 V, Differential Analog Input, ENCODE = 100 MSPS unless AD9071–SPECIFICATIONS otherwise noted.) Parameter Temp Test Level Min AD9071BR Typ RESOLUTION DC ACCURACY Differential Nonlinearity1 10 ± 0.8 ± 1.0 ± 0.8 ± 1.25 Guaranteed ±1 ±2 150 25°C Full 25°C Full 25°C 25°C Full Full I VI I VI I I VI V Full Full 25°C Full Full 25°C 25°C Full 25°C V V I VI VI V I VI V REFERENCE OUTPUT Output Voltage Temperature Coefficient Full Full VI V VCC – 2.6 SWITCHING PERFORMANCE Maximum Conversion Rate Minimum Conversion Rate Encode Pulsewidth High (tEH) Encode Pulsewidth Low (tEL) Aperture Delay (tA) Aperture Uncertainty (Jitter) Output Valid Time (tV)3 Output Propagation Delay (tPD)3 Output Rise Time (tR) Output Fall Time (tF) Full Full 25°C 25°C 25°C 25°C Full Full Full Full VI IV IV IV V V VI VI V V 100 DIGITAL INPUT Logic “1” Voltage Logic “0” Voltage Logic “1” Current Logic “0” Current Input Capacitance Full Full Full Full 25°C VI VI VI VI V 2.0 Full Full VI VI VDD – 0.5 Integral Nonlinearity1 No Missing Codes1 Gain Error2 Gain Tempco2 ANALOG INPUT Input Voltage Range (With Respect to AIN) Common-Mode Voltage Input Offset Voltage Input Resistance Input Capacitance Input Bias Current Analog Bandwidth, Full Power DIGITAL OUTPUTS Logic “1” Voltage Logic “0” Voltage Output Coding POWER SUPPLY VCC Supply Current (VCC = 5 V)4 VDD Supply Current (VDD = 3.3 V)4 Power Dissipation4 Power Supply Sensitivity5 Max 15 Bits +1.5/–1.0 +1.75/–1.0 ± 1.5 ± 1.75 LSB LSB LSB LSB ±4 ±8 % FS % FS ppm/°C ± 512 –2.5 ± 0.2 ±4 ± 18 ±5 ± 20 35 3 55 90 65 115 280 mV p-p V mV mV kΩ pF µA µA MHz VCC – 2.5 130 V ppm/°C VCC – 2.4 40 13 13 4.5 4.5 1.1 3.0 4.0 5.0 1.4 1.0 2.0 Unit 7.0 0.8 ± 10 –500 3 MSPS MSPS ns ns ns ps, rms ns ns ns ns V V µA µA pF 0.05 V V 115 14 620 0.010 mA mA mW V/V Offset Binary Full Full Full 25°C VI VI VI I –2– 85 7.5 450 0.002 REV. C AD9071 Parameter Temp Test Level 25°C 25°C V V 25°C Full 25°C Full I V I V 54 25°C Full 25°C Full I V I V 54 25°C 25°C I I 25°C 25°C Min AD9071BR Typ Max Unit 6 DYNAMIC PERFORMANCE Transient Response Overvoltage Recovery Time Signal-to-Noise Ratio (SNR) (Without Harmonics) fIN = 10.3 MHz fIN = 41 MHz Signal-to-Noise Ratio (SINAD) (With Harmonics) fIN = 10.3 MHz fIN = 41 MHz Effective Number of Bits fIN = 10.3 MHz fIN = 41 MHz 2nd Harmonic Distortion fIN = 10.3 MHz fIN = 41 MHz 3rd Harmonic Distortion fIN = 10.3 MHz fIN = 41 MHz Two-Tone Intermodulation (IMD) fIN = 10.3 MHz fIN = 41 MHz 4 5 ns ns 56 55 55 54 dB dB dB dB 56 55 54 53 dB dB dB dB 8.8 8.5 9.2 8.8 Bits Bits I I 63 60 75 66 dBc dBc 25°C 25°C I I 65 57 75 65 dBc dBc 25°C 25°C V V 70 60 dBc dBc 53 52 NOTES 1 Differential and integral nonlinearity based on F S = 80 MSPS. 2 Gain error and gain temperature coefficient are based on the ADC only (with a fixed 2.5 V external reference). 3 tV and tPD are measured from the threshold crossing of the ENCODE input to the 50% levels of the digital outputs. The output ac load during test is 5 pF. 4 Power dissipation is measured under the following conditions: F S @ 100 MSPS, analog input is –1 dBFS at 10.3 MHz. 5 A change in input offset voltage with respect to a change in V CC. 6 SNR/harmonics based on an analog input voltage of –1.0 dBFS referenced to a 1.024 V full-scale input range. Typical thermal impedance for the R style (SOIC) 28-lead package: θJC = 23°C/W, θCA = 48°C/W, θJA = 71°C/W. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS* EXPLANATION OF TEST LEVELS Test Level VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC to 0.0 V Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC to 0.0 V VREF IN, VREF OUT . . . . . . . . . . . . . . . . . . . . VCC to 0.0 V Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Operating Temperature . . . . . . . . . . . . . . . . . –40°C to +85°C Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C Maximum Junction Temperature . . . . . . . . . . . . . . . . . 150°C Maximum Case Temperature . . . . . . . . . . . . . . . . . . . . 150°C I. 100% production tested. II. 100% production tested at 25°C and sample tested at specified temperatures. III. Sample tested only. IV. Parameter is guaranteed by design and characterization testing. V. Parameter is a typical value only. *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods may effect device reliability. VI. 100% production tested at 25°C; guaranteed by design and characterization testing for industrial temperature range. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9071 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. C –3– WARNING! ESD SENSITIVE DEVICE AD9071 ORDERING GUIDE Model Temperature Range Package Description Package Option AD9071BR AD9071/PCB –40°C to +85°C 25°C 28-Lead Wide Body (SOIC) Evaluation Board R-28 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1, 7, 12, 21, 23 2, 8, 11 3 4 5, 6 9 10 13 14 GND VCC VREF OUT VREF IN DNC AIN AIN ENCODE OR 15–19, 24–28 20, 22 D9–D0 VDD Ground Analog Power Supply. Nominally 5.0 V. (Tie together to prevent a possible latch-up condition.) Internal Reference Output (VCC – 2.5 V typical); Bypass with 0.1 µF to VCC. Reference Input for ADC (VCC – 2.5 V typical). Do Not Connect Analog Input – Complementary Analog Input – True Encode clock for ADC. (ADC Samples on Rising Edge of ENCODE.) Out-of-Range Output. Goes HIGH when the converted sample is more positive than 3FFH or more negative than 000H (offset binary coding). Digital outputs of ADC. D9 is the MSB. Data is offset binary. Digital Output Power Supply. User selectable range from 3 V to 5 V. PIN CONFIGURATION GND 1 28 D0 VCC 2 27 D1 VREF OUT 3 26 D2 VREF IN 4 25 D3 NC 5 24 D4 NC 6 AD9071BR 23 GND GND 7 TOP VIEW 22 VDD (Not to Scale) 21 GND VCC 8 AIN 9 20 VDD AIN 10 19 D5 VCC 11 18 D6 GND 12 17 D7 ENCODE 13 16 D8 OR 14 Table I. Output Coding 15 D9 (MSB) NC = NO CONNECT –4– Code AIN–AIN Offset Binary OR 1023 1023 1022 • • • 513 512 511 • • • 1 0 0 ≥ 0.512 V 0.511 V 0.510 V • • • 0.001 V 0.000 V –0.001 V • • • –0.511 V –0.512 V ≤–0.513 V 11 1111 1111 11 1111 1111 11 1111 1110 • • • 10 0000 0001 10 0000 0000 01 1111 1111 • • • 00 0000 0001 00 0000 0000 00 0000 0000 1 0 0 • • • 0 0 0 • • • 0 0 1 REV. C AD9071 SAMPLE N–1 SAMPLE N SAMPLE N+3 SAMPLE N+4 AIN SAMPLE N+1 tA tEH tEL SAMPLE N+2 1/f s ENCODE tPD D9–D0 DATA N–4 DATA N–3 DATA N–2 DATA N–1 tV DATA N DATA N+1 Figure 1. Timing Diagram VDD VCC AIN AIN D9–0, OR Figure 2. Equivalent Analog Input Circuit Figure 5. Equivalent Digital Output Circuit VCC VCC VREF OUT VREF IN Figure 3. Equivalent Reference Input Circuit Figure 6. Equivalent Reference Output Circuit VCC ENCODE Figure 4. Equivalent Encode Input Circuit REV. C –5– AD9071–Typical Performance Characteristics 0 0 FUNDAMENTAL = –1.0dBFS SNR = 56.75dB SINAD = 56.56dB 2ND HARMONIC = –71.88dB 3RD HARMONIC = –77.28dB –10 –20 –30 –30 –40 –40 dB dB –20 –50 –50 –60 –60 –70 –70 –80 –80 –90 –90 –100 –100 0 F1 = 41.1MHz F2 = 42.1MHz F1 = F2 = –7.0dBFS –10 50 0 50 MHz MHz TPC 1. Spectrum: FS = 100 MSPS, fIN = 10.3 MHz TPC 4. Two-Tone Intermodulation Distortion 0 60 FUNDAMENTAL = –1.0dBFS SNR = 55.23dB SINAD = 54.35dB 2ND HARMONIC = –68.28dB 3RD HARMONIC = –62.83dB –10 58 56 –30 54 –40 52 dB dB –20 –50 50 –60 48 –70 46 –80 44 –90 42 –100 40 0 SNR 50 SINAD 10 20 40 MHz 120 140 58 0 57 F1 = 9.63MHz F2 = 10.63MHz F1 = F2 = –7.0dBFS –10 –20 56 SNR 55 –30 54 dB –40 dB 100 TPC 5. SINAD/SNR vs. fIN: FS = 100 MSPS TPC 2. Spectrum: FS = 100 MSPS, fIN = 41 MHz –50 SINAD 53 52 –60 51 –70 50 –80 49 –90 –100 60 80 fIN – MHz 0 48 10 50 MHz 20 40 60 80 F S – MSPS 100 120 140 TPC 6. SINAD/SNR vs. FS: fIN = 10.3 MHz TPC 3. Two-Tone Intermodulation Distortion –6– REV. C AD9071 60 60 58 SNR SNR 56 SINAD SINAD 55 54 dB dB 52 50 50 48 46 45 44 42 40 –40 –15 5 55 25 40 2.5 85 3.5 4.5 5.5 ENCODE PULSEWIDTH – ns TC TPC 7. Differential SNR vs. TC: fIN = 10.3 MHz 6.5 7.5 TPC 9. SNR vs. Clock Pulsewidth (tEH): fIN = 10.3 MHz 0 60 SNR 58 –1 56 SINAD –2 54 –3dB ROLLOFF POINT –3 dB dB 52 50 –4 48 46 –5 44 –6 42 40 –40 –15 5 55 25 –7 85 15 60 105 TC TPC 8. Single-Ended SNR vs. TC: fIN = 10.3 MHz 80 DIFFERENTIAL INPUT 70 dBc 60 SINGLE-ENDED 50 40 30 20 10 20 30 40 fIN – MHz TPC 11. Second Harmonic Performance: SingleEnded vs. Differential Input REV. C 195 240 fIN – MHz 285 330 TPC 10. Frequency Response 90 0 10 150 –7– 375 420 AD9071 APPLICATION NOTES comparators detect when the analog input signal is out of this range, and set the OR output signal HIGH. The digital outputs are locked at plus or minus full scale (3FFH or 200H) for voltages that are out of range, but between 1 V and 5 V. Input voltages outside of this range may result in invalid codes at the ADC’s output. THEORY OF OPERATION The AD9071 employs a two-step subranging architecture with digital error correction. The sampling and conversion process is initiated by a rising edge at the ENCODE input. The analog input signal is buffered by a high speed differential amplifier and applied to a track-and-hold (T/H) circuit, which captures the value of the input at the sampling instant and maintains it for the duration of the conversion. VREF (+2.5V) 100⍀ 100⍀ 0.1F The coarse quantizer (ADC) produces a 5-bit estimate of the input value. Its digital output is reconverted to analog form by the reconstruction DAC and subtracted from the input signal in the SUM AMP. The second stage quantizer generates a 6-bit representation of the difference signal. The eleven bits are presented to the ENCODE LOGIC, which corrects for range overlap errors and produces an accurate 10-bit result. AIN 50⍀ AD9071 0.1F AIN 25⍀ Figure 8. Single-Ended Analog Input Configuration Data are strobed to the output on the rising edge of the ENCODE input, with the data from sample N appearing on the output following ENCODE rising edge N+3. When the analog input signal returns to the nominal range, the out-of-range comparators return the ADC to its active mode and the device recovers in the overvoltage recovery time. Voltage Reference USING THE AD9071 ENCODE Input A stable and accurate 2.5 V voltage reference (VCC – 2.5 V) is built into the AD9071 (VREF OUT). In normal operation, the internal reference is used by strapping Pins 3 and 4 of the AD9071 together. The internal reference can provide 100 µA of extra drive current that may be used for other circuits. Any high-speed A/D converter is extremely sensitive to the quality of the sampling clock provided by the user. A track/hold circuit is essentially a mixer, and any noise, distortion, or timing jitter on the clock will be combined with the desired signal at the A/D output. For that reason, considerable care has been taken in the design of the ENCODE input of the AD9071, and the user is advised to give commensurate thought to the clock source. The lowest jitter clock source is a crystal oscillator producing a pure sine wave. Some applications may require greater accuracy, improved temperature performance, or adjustment of the gain of the AD9071, which cannot be obtained by using the internal reference. For these applications, an external 2.5 V reference can be connected to VREF IN, which requires 5 µA of drive current (see Figure 9). The ENCODE input is fully TTL/CMOS compatible. Digital Outputs +5V The digital outputs are CMOS compatible for lower power consumption. 200 Ω series resistors are recommended between the AD9071 and the receiving logic to reduce transients and improve SNR. AD780 +5V +VIN 1M⍀ TRIM GND AD9071 VREF IN VOUT 1F Analog Input 0.1F 25k⍀ O/P SELECT The analog input has been optimized for differential signal input. NC NC = NO CONNECT VREF (+2.5V) T1A T1 - 1T 100⍀ Figure 9. Using the AD780 Voltage Reference 100⍀ 0.1F The input range can be adjusted by varying the reference voltage applied to the AD9071. No appreciable degradation in performance occurs when the reference is adjusted ± 4%. The fullscale range of the ADC tracks reference voltage changes linearly. AIN 50⍀ 0.1F AD9071 AIN Timing The performance of the AD9071 is insensitive to the duty cycle of the clock over a wide range of operating conditions (see TPC 9). Figure 7. Differential Analog Input Configuration If driven single-endedly, the AIN should be connected to a clean reference and bypassed to ground. For best dynamic performance, impedances at AIN and AIN should match. The AD9071 provides latched data outputs, with three pipeline delays. Data outputs are available one propagation delay (tPD) after the rising edge of the encode command (see Figure 1). The length of the output data lines, and loads placed on them, should be minimized to reduce transients within the AD9071; these transients can detract from the converter’s dynamic performance. Special care was taken in the design of the analog input section of the AD9071 to prevent damage and corruption of data when the input is overdriven. The nominal input range is 1.988 V to 3.012 V (1.024 V p-p centered at 2.5 V). Out-of-range –8– REV. C AD9071 resistor on Data Ready (R33), normally 0 ohms, is provided to support various user output impedance configurations. The AD9760 DAC supports viewing reconstructed A/D data at J4. The minimum guaranteed conversion rate of the AD9071 is 40 MSPS. At clock rates below 40 MSPS, dynamic performance may degrade. The AD9070 will operate in bursts, but the user must flush the internal pipeline each time the clock restarts. Valid data will be produced on the fourth rising edge of the ENCODE signal after the clock is restarted. Voltage Reference The AD9071 can be operated using its internal voltage reference (connect E2 to E3) or an optional external reference (connect E1 to E2). The board is shipped utilizing the internal voltage reference. EVALUATION BOARD The AD9071 evaluation board is a convenient and easy way to evaluate the performance of the AD9071 in the SOIC package. The board consists of an internal voltage reference or an optional external reference, two 74LCX574 latches for capturing data from the A/D converter, and an AD9760 DAC for viewing reconstructed A/D data. The AD9071 output logic can be driven at 5 V and 3.3 V levels. The latches are set up at 3.3 V but are 5 V tolerant. Test points are provided at Encode, DB9, DB0, Data Ready, and Data Clock. All are clearly labeled. Layout The AD9071 is not layout sensitive if some important guidelines are met. The evaluation board layout provides an example where these guidelines have been followed to optimize performance. • Provide a good ground plane connecting the analog and digital sections. • Excellent bypassing is essential. Chip capacitors with 0.1 µF values and 0803 dimensions are placed flush against the pins. Placing any of the capacitors on the bottom of the board can degrade performance. These techniques reduce the amount of parasitic inductance that can impact the bypassing ability of the caps. Analog Input The evaluation board can be driven single-ended or differentially. Differential input requires using a 1:1 transformer. For single-ended operation (J2), Jumper S5 is connected to S8 and S6 is connected to S7. For differential input operation (J3), S5 is connected to S3 and S4 is connected to S6. The board is shipped in the differential configuration. • Separate power planes and supplies for the analog and digital sections are recommended. The AD9071 evaluation board is provided as a design example for customers of Analog Devices. ADI makes no warranties express, statutory, or implied regarding merchantability or fitness for a particular purpose. Encode The AD9071 encode inputs are driven single-ended into J1 and are at TTL logic levels. Data Out The data delivered out of the AD9071 is in offset binary format at TTL levels. The Data Ready signal can be inverted by opening the S1 and S2 connections. An optional series termination Figure 10. Printed Circuit Board Top Side Silkscreen REV. C Figure 11. Printed Circuit Board Bottom Side Silkscreen –9– AD9071 Figure 12. Printed Circuit Board Top Side Copper Figure 14. Printed Circuit Board “Split” Power Layer Figure 13. Printed Circuit Board Ground Layer Figure 15. Printed Circuit Board Bottom Side Copper –10– REV. C REV. C U1 74LCX574 E3 VREF EXT C7 0.1F SMB A IN J2 2, 3, 4, 5 - GND VREF 1 S8 3 C5 0.1F S3 SMB A IN DIF T1 J3 3 4 R4 2, 3, 4, 50⍀ 2 5 - GND S9 R1 S5 100⍀ ANALOG IN S4 S6 –11– Figure 16. Printed Circuit Board Schematic S7 9 ANALOG IN C22 0.1F 10 ENCODE IN J1 2, 3, 4, 5 - GND 1 2 R6 50⍀ S1 S2 R31 4.99k⍀ U5 74LCX86 3 12 13 11 9 10 8 DNC DNC AIN AIN ENCODE TP1 ENCODE D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 OR 28 7 8 R13 200⍀ 27 26 25 24 19 18 17 16 15 9 R14 200⍀ D0 Q0 D1 Q1 D2 Q2 D3 Q3 D4 Q4 D5 Q5 D6 Q6 D7 Q7 1 3 6 5 2 R17 200⍀ 3 14 4 R18 200⍀ 5 6 7 TP2 8 R3 200⍀ 9 D0 Q0 D1 Q1 D2 Q2 D3 Q3 D4 Q4 D5 Q5 D6 Q6 D7 Q7 CLOCK 4 5 C1 0.1F C20 10F TB6 DB2 16 15 14 C17 0.1F C6 0.1F C18 10F C21 10F C11 0.1F C12 0.1F DB3 12 DB4 DATABIT 4 R22 100⍀ DATABIT 5 R21 100⍀ DATABIT 6 R20 100⍀ DATABIT 7 R29 100⍀ DATABIT 8 R28 100⍀ DATABIT 9 R30 100⍀ OVERRANGE DB5 DB6 19 DB5 18 DB6 DB7 17 16 DB8 15 DB7 14 DB8 13 DB9 DB9 12 OR OR 11 GND GND R33 0⍀ DATA READY R35 150⍀ R37 150⍀ +VD J5 VCC VDD 10 9 8 7 6 5 4 3 2 1 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 +VD C14 0.1F DAC OUT AD9760 CLK DVDD AVDD COMP2 COMP1 FSADJ REFIO REFLO SLEEP 19 17 16 18 27 23 24 15 C2 0.1F 22 C9 0.1F 21 R7 50⍀ S13 S11 R2 2k⍀ C10 0.1F SNS J4 2, 3, 4, 5, - GND S12 +VD R8 50⍀ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 P2 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 DATA READY DATABIT 0 DATABIT 1 DATABIT 2 DATABIT 3 DATABIT 4 DATABIT 5 DATABIT 6 DATABIT 7 DATABIT 8 DATABIT 9 OVERRANGE AD9071 C3 0.1F R23 100⍀ DB4 11 IOUTB C15 0.1F DATABIT 3 DB3 13 IOUTA C8 0.1F DATABIT 2 R24 100⍀ DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 +VD C17 0.1F R25 100⍀ DB2 R36 150⍀ 28 C19 10F C37DPPF R26 100⍀ DATABIT 1 +VD +VD VREF EXT DB1 DATABIT 0 TP5 VDD 6 DB1 17 GND : 10 +VD : 20 TP4 GND VCC 18 OUT EN TB1 2 DB0 U2 74LCX574 R16 200⍀ + VD : 14 GND : 7 1 19 GND : 10 +VD : 20 DATA CLK DATA READY OUT EN CLOCK R15 200⍀ VCC : 2, 8, 11 VDD : 20, 22 GND : 1, 7 12, 21, 23 R27 100⍀ DB0 R34 150⍀ 4 +VD VREF IN R32 25⍀ 13 SMB R12 200⍀ VREF OUT U3 AD9071 R19 100⍀ T1 – 1T C4 0.1F 6 5 6 S10 GND 1 5 4 R11 200⍀ C13 0.1F 4 R5 50⍀ 6 1 3 R10 200⍀ VCC E2 2 TP3 VREF INT 1 E1 1 R9 200⍀ AD9071 Table II. Printed Circuit Board Bill of Materials Item # Quantity Reference Description 1 18 Ceramic Chip Capacitor, 0603, 0.1 µF 2 3 4 5 6 7 4 3 4 1 1 13 8 9 1 11 10 11 12 13 14 15 5 1 1 1 4 13 16 17 1 1 C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C12, C13, C14, C15, C16, C17, C22 C18, C19, C20, C21 E1, E2, E3 J1, J2, J3, J4 J5 P2 R1, R19, R20, R21, R22, R23, R24, R25, R26, R27, R28, R29, R30 R2 R3, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18 R4, R5, R6, R7, R8 R31 R32 R33 R34, R35, R36, R37 S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S13 T1 TB1 18 19 20 21 22 5 2 1 1 1 TP1, TP2, TP3, TP4, TP5 U1, U2 U3 U4 U5 C00567b–0–8/01(C) Tantalum Chip Capacitor, 10 µF Jumpers SMB-P Connector 20-Pin Male Header 37-Pin Connector (Amp 747462-4) Surface Mount Resistor, 1206, 100 Ω Surface Mount Resistor, 1206, 2000 Ω Surface Mount Resistor, 1206, 200 Ω Surface Mount Resistor, 1206, 50 Ω Surface Mount Resistor, 1206, 5000 Ω Surface Mount Resistor, 1206, 25 Ω Surface Mount Resistor, 1206, 0 Ω Surface Mount Resistor, 1206, 150 Ω Jumpers Surface Mount Transformer Mini-Circuit T1-T1, 1:1 Ratio 6-Pin Wieland Connector (P/N # 25,602, 2653.0; 25.530 3625.0) Test Points 74LCX574 Octal Latch AD9071BR, 10-Bit, 100 MSPS, ADC AD9760AR, 10-Bit, 125 MSPS, DAC 74LCX86, XOR OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 28-Lead Wide Body SOIC (R-28) 0.7125 (18.10) 0.6969 (17.70) 28 15 0.2992 (7.60) 0.2914 (7.40) 0.4193 (10.65) 0.3937 (10.00) 1 14 0.0118 (0.30) 0.0040 (0.10) 0.1043 (2.65) 0.0926 (2.35) 0.0500 (1.27) BSC 0.0192 (0.49) SEATING 0.0138 (0.35) PLANE 0.0125 (0.32) 0.0091 (0.23) 0.0291 (0.74) ⴛ 45ⴗ 0.0098 (0.25) 8° 0° PRINTED IN U.S.A. PIN 1 0.0500 (1.27) 0.0157 (0.40) AD9071–Revision History Location Page Data Sheet changed from REV. B to REV. C. Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 –12– REV. C