SLUS347A – MAY 1995 – REVISED APRIL 2003
FEATURES
D Complies with SCSI, SCSI–2 and SPI–2
D
D
D
D
D
D
D
D
D
D
DESCRIPTION
Standards
2.7-V to 5.25-V Operation
1.8-pF Channel Capacitance during
Disconnect
0.5-µA Supply Current in Disconnect Mode
110-Ω/2.5-kΩ Programmable Termination
Completely Meets SCSI Hot Plugging
–400-mA Sourcing Current for Termination
+400-mA Sinking Current for Active Negation
Drivers
Trimmed Termination Current to 4%
Trimmed Impedance to 7%
Current Limit and Thermal Shutdown
Protection
The UCC5606 provides 9 lines of active termination for
a small computer systems interface (SCSI) parallel bus.
The SCSI standard recommends active termination at
both ends of the cable segment.
The UCC5606 is ideal for high performance 3.3-V SCSI
systems. The key features contributing to such low
operating voltage are the 0.1-V drop out regulator and
the 2.7-V reference. During disconnect the supply
current is typically only 0.5 µA, which makes the device
attractive for battery powered systems.
The UCC5606 is designed with an ultra-low channel
capacitance of 1.8 pF, which eliminates effects on signal
integrity from disconnected terminators at interim points
on the bus.
BLOCK DIAGRAM
UDG–94067–1
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright 2003, Texas Instruments Incorporated
!"# $"%&! '#(
'"! ! $#!! $# )# # #* "#
'' +,( '"! $!# - '# #!# &, !&"'#
# - && $## (
www.ti.com
1
SLUS347A – MAY 1995 – REVISED APRIL 2003
DESCRIPTION (CONTINUED)
The UCC5606 can be programmed for either a 110-Ω or 2.5-kΩ termination. The 110-Ω termination is used for
standard SCSI bus lengths and the 2.5-kΩ termination is typically used in short bus applications. When driving
the TTL compatible DISCNCT pin directly, the 110-Ω termination is connected when the DISCNCT pin is driven
high, and disconnected when low. When the DISCNCT pin is driven through an impedance between 80 kΩ and
150 kΩ, the 2.5-kΩ termination is connected when the DISCNCT pin is driven high, and disconnected when
driven low.
The power amplifier output stage allows the UCC5606 to source full termination current and sink active negation
current when all termination lines are actively negated.
The UCC5606 is pin-for-pin compatible with Unitrode’s other 9-line single-ended SCSI terminators, except that
DISCNCT is now active low, allowing lower capacitance and lower voltage upgrades to existing systems. The
UCC5606 is completely hot pluggable and appears as high impedance at the terminating channels with
VTRMPWR = 0 V or open.
Internal circuit trimming is utilized, first to trim the 110-Ω termination impedance to a 7% tolerance, and then most
importantly, to trim the output current to a 4% tolerance, as close to the maximum SCSI specification as possible,
which maximizes noise margin in fast SCSI operation.
Other features include thermal shutdown and current limit.
This device is offered in low thermal resistance versions of the industry standard 16-pin narrow body SOIC,
16-pin N and 24-pin TSSOP.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted{}
UCC5606
TRMPWR voltage
7
Signal line voltage
0 to 7
Regulator output current
UNIT
V
0.6
A
Storage temperature, Tstg
–65 to 150
Operating junction temperature, TJ
–55 to 150
°C
C
Lead temperature (soldering, 10 sec.)
300
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is
not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect
to GND. Currents are positive into and negative out of, the specified terminal.
‡ Currents are positive into, negative out of the specified terminal. Consult Packaging Section of Databook for thermal limitations and
considerations of packages. All voltages are referenced to GND.
RECOMMENDED OPERATING CONDITIONS
MAX
UNIT
TRMPWR voltage
2.7
MIN
NOM
5.25
V
Signal line voltage
0
5
V
Disconnect input voltage
0
TRMPWR
°C
ORDERING INFORMATION
TA
0°C to 70°C
DISCONNECT
STATUS
PACKAGED DEVICE{
DIL–16 (N)
SOIC–16 (DP)
UCC5606N
UCC5606DP
TSSOP–24 (PWP)
UCC5606PWP
† The LQFP packages are available taped and reeled. Add TR suffix to device type (e.g. UCC5606PWPTR) to order quantities of 2,500 devices
per reel.
2
www.ti.com
SLUS347A – MAY 1995 – REVISED APRIL 2003
CONNECTION DIAGRAM
DIL–16 (Top View)
N Package
SOIC–16 (Top View)
DP Package
TSSOP–24 (Top View)
PWP Package
NOTE: GND* serves as a heat sink ground which must be tied to a large copper area or the grounding plate.
ELECTRICAL CHARACTERISTICS
TA = 0°C to 70°C, TRMPWR = 3.3 V, DISCNCT = 3.3 V, RDISCNCT = 0 Ω, TA = TJ, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Supply Current Section
Termpwr supply current
Power down mode
All termination lines = open
1
2
All termination lines = 0.2 V
210
218
DISCNCT = 0 V
0.5
5.0
102.3
110.0
117.7
2.5
2.7
3.0
–22.1
–23.0
–24.0
–21
–23
–24
–20.2
–23.0
–24.0
–19
–23
mA
µA
Output Section (110 ohms – Terminator Lines)
Terminator impedance
Output high voltage
Max output current
TRMPWR = 3 V (1)
VLINE = 0.2 V,
VLINE = 0.2 V
TJ = 25°C
VLINE = 0.2 V,
TJ = 25°C (1)
VLINE = 0.2 V,
TRMPWR = 3 V,
Output leakage
VLINE = 0.5 V
DISCNCT = 0 V,
Output capacitance
DISCNCT = 0 V,
TRMPWR = 3 V (1)
Ohms
V
mA
–24
–22.4
TRMPWR = 0 V to 5.25 V
DP package (2)
10
400
nA
1.8
2.5
pF
2.0
2.5
3.0
kΩ
2.5
2.7
3.0
V
–0.7
–1.0
–1.4
–0.6
–1.0
–1.5
10
400
nA
1.8
2.5
pF
Output Section (2.5 kΩ – Terminator Lines) (RDISCNCT = 80 kΩ)
Terminator impedance
Output high voltage
TRMPWR = 3 V (1)
Max output current
VLINE = 0.2 V
VLINE = 0.2 V,
Output leakage
DISCNCT = 0 V,
Output capacitance
DISCNCT = 0 V,
TRMPWR = 3 V (1)
TRMPWR = 0 to 5.25 V
DP package (2)
www.ti.com
mA
3
SLUS347A – MAY 1995 – REVISED APRIL 2003
ELECTRICAL CHARACTERISTICS
TA = 0°C to 70°C, TRMPWR = 3.3 V, DISCNCT = 3.3 V, RDISCNCT = 0 Ω, TA = TJ, (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Regulator Section
Regulator output voltage
5.25 V > TRMPWR > 3 V
Drop-out voltage
All termination lines = 0.2 V
Short circuit current
Thermal shutdown
VREG = 0 V
VREG = 3 V
(2)
Thermal shutdown hysteresis
(2)
Sinking current capability
2.5
2.7
3.0
0.1
0.2
–200
–400
–800
200
400
800
V
mA
°C
170
10
Disconnect Section
Disconnect threshold
RDISCNCT = 0 kΩ to 80 kΩ
Input current
DISCNCT = 3.3 V
0.8
1.5
2.0
V
30
50
µA
NOTES: 1. Measuring each termination line while other eight are low (0.2 V).
2. Ensured by design. Not production tested.
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NO.
DISCNCT
7
GND
9
LINE1 TO
LINE9
4
I
110-Ω termination channels
REG
9
I
Output of the internal 2.7-V regulator
TRMPWR
4
GND*
4
I/O
NAME
I
Taking this pin low causes the 9 channels to become high impedance and the chip to go into low
power mode. In short laptop buses an 80-kΩ to 150-kΩ resister to TERPWR terminates the bus at
2.5 kΩ. Less than 110 Ω to TERPWR enables the terminator.
Ground reference for the device
Power for the device
Heat sink ground, must be tied to a large copper area or the grounding plate.
www.ti.com
SLUS347A – MAY 1995 – REVISED APRIL 2003
APPLICATION INFORMATION
UDG–98100
Figure 1. Typical SCSI Bus Configurations Utilizing two UCC5606 Devices
UDG–98100
Figure 2. Typical Wide SCSI Bus Configurations Utilizing three UCC5606 Devices
www.ti.com
5
PACKAGE OPTION ADDENDUM
www.ti.com
26-Mar-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
UCC5606DP
OBSOLETE
SOIC
D
16
TBD
Call TI
Call TI
0 to 70
UCC5606DP
UCC5606DPTR
OBSOLETE
SOIC
D
16
TBD
Call TI
Call TI
0 to 70
UCC5606DP
UCC5606DPTRG4
OBSOLETE
SOIC
UCC5606DP
UCC5606J
OBSOLETE
D
16
TBD
Call TI
Call TI
0 to 70
UTR
16
TBD
Call TI
Call TI
0 to 70
UCC5606N
OBSOLETE
PDIP
N
16
TBD
Call TI
Call TI
0 to 70
UCC5606PWP
OBSOLETE
TSSOP
PW
24
TBD
Call TI
Call TI
0 to 70
UCC5606PWP
UCC5606PWPTR
ACTIVE
TSSOP
PW
24
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
0 to 70
UCC5606PWP
2000
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
26-Mar-2015
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Aug-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
UCC5606PWPTR
Package Package Pins
Type Drawing
TSSOP
PW
24
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2000
330.0
16.4
Pack Materials-Page 1
6.95
B0
(mm)
K0
(mm)
P1
(mm)
8.3
1.6
8.0
W
Pin1
(mm) Quadrant
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Aug-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC5606PWPTR
TSSOP
PW
24
2000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated