1 2 FL PSE 2TX Power-over-Ethernet Module (PSE) for Midspan Power Supply in Accordance with IEEE 802.3af US X5 X1 1 TH E 1 E PO 2 H ET AUTOMATIONWORX Data Sheet X62 X3 X84 E2 PO © PHOENIX CONTACT - 02/2006 Description 724200000 TX 13 E 2 910 PS .28 FL .-No Ord Features The Power-over-Ethernet module for industrial use enables common transmission of power and data in accordance with IEEE 802.3af via Ethernet. In this way, the termination devices such as WLAN/Bluetooth access points, IP phones, or IP cameras can be connected fast and cost-effectively. The FL PSE 2TX is a compact stand-alone solution converting two standard Ethernet ports into two Powerover-Ethernet ports. The FL PSE 2TX is a plug & play device generating those 48 V DC from the 24 V module power supply required for Power-over-Ethernet according to IEEE 802.3af. – – – – – – – 2 PoE supply ports No configuration required Automatic detection of connected devices Can operate on 10 Mbps and 100 Mbps networks Convenient diagnostic and status indicators Redundant 24 V DC supply possible Connection for optimum functional earth ground Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. This data sheet is valid for all products listed on the following page: 7242_en_00 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00 • www.phoenixcontact.com www.phoenixcontact.com/salesnetwork 1 FL PSE 2TX Ordering Data Products Description Type Order No. Pcs./Pkt. Module for PoE midspan power supply FL PSE 2TX 2891013 1 Accessories Description Type Order No. Pcs./Pkt. Universal end clamp E/NS 35 N 0800886 50 Patch cable, CAT 5, pre-assembled, 0.3 m long FL CAT5 PATCH 0,3 2832250 10 Patch cable, CAT 5, pre-assembled, 0.5 m long FL CAT5 PATCH 0,5 2832263 10 Patch cable, CAT 5, pre-assembled, 1.0 m long FL CAT5 PATCH 1,0 2832276 10 Patch cable, CAT 5, pre-assembled, 1.5 m long FL CAT5 PATCH 1,5 2832221 10 Patch cable, CAT 5, pre-assembled, 2.0 m long FL CAT5 PATCH 2,0 2832289 10 Patch cable, CAT 5, pre-assembled, 3.0 m long FL CAT5 PATCH 3,0 2832292 10 Patch cable, CAT 5, pre-assembled, 5.0 m long FL CAT5 PATCH 5,0 2832580 10 Patch cable, CAT 5, pre-assembled, 7.5 m long FL CAT5 PATCH 7,5 2832616 10 Patch cable, CAT 5, pre-assembled, 10.0 m long FL CAT5 PATCH 10 2832629 10 Technical Data General Data Function Power-over-Ethernet module (PSE) for midspan power supply Housing dimensions (width x height x depth) 45 mm x 99 mm x 112 mm Permissible operating temperature 0°C to +55°C (see derating curve) Permitted storage temperature -20°C to +70°C Degree of protection IP20, DIN 40050, IEC 60529 Class of protection Class 3 VDE 0106; IEC 60536 Maximum humidity (operation) 30% to 95%, no condensation Maximum humidity (storage/transport) 30% to 95%, no condensation Air pressure (operation) 86 kPa to 108 kPa, 1500 m above sea level Air pressure (operation) 66 kPa to 108 kPa, 3500 m above sea level Preferred mounting position Perpendicular to a standard DIN rail Connection to protective earth ground By snapping it on a grounded DIN rail / via COMBICON (optional) Weight 320 g, typical Supply Voltage Connection Via COMBICON; maximum conductor cross section = 2.5 mm2 Nominal value 24 V DC Permissible ripple 3.6 Vpp within the permissible voltage range Permissible voltage range 18.5 V DC to 30.5 V DC Current consumption at US approx. 100 mA at no-load operation; approx. 1800 mA at 24 V at the input and at maximum admissible load and at an ambient temperatureof 25°C Test voltage 1500 V AC for 1 minute 7242_en_00 PHOENIX CONTACT 2 FL PSE 2TX Supply Voltage (Continued) Protection against polarity reversal Present Power consumption approx. 2.4 W at no-load operation; approx. 43.5 W at 24 V at the input and at maximum admissible load and at an ambient temperatureof 25°C Derating P /W out 30 20 10 0 0 10 20 30 40 50 60 T /°C out Interfaces Number of standard Ethernet ports 2 Number of PoE ports 2 Connection format 8-pos. RJ45 socket at the device Connection medium Twisted pair cable with a conductor cross section of 0.14 mm2 to 0.22 mm2 Impedance 100 Ohm Transmission speed 10/100 Mbps PoE supply in acc. with IEEE 802.3af 48 V DC / Class 0 Mechanical Tests Shock test according to IEC 60068-2-27 30g Vibration resistance according to IEC 60068-2-6 Operation/storage/transport: 5g, Criterion A Free fall according to IEC 60068-2-32 1m Conformance With EMC Directives Developed according to IEC 61000-6-2 IEC 61000-4-2 (ESD) Criterion B IEC 61000-4-3 (radiated-noise immunity) Criterion A IEC 61000-4-4 (burst) Criterion A IEC 61000-4-5 (surge) Criterion B IEC 61000-4-6 (conducted noise immunity) Criterion A IEC 61000-4-8 (noise immunity against magnetic fields) Criterion A EN 55022 (noise emission) Class A General Information Warning Disregarding this warning may result in damage to equipment and/or serious personal injury. Only qualified personnel may start up and operate this device. According to the safety instructions in this text, qualified personnel are persons who are authorized to start up, to ground, and to mark devices, systems, and equipment according to the standards of safety technology. In addition, these persons must be familiar with all warning instructions and maintenance measures in this text. Warning The FL PSE 2TX module is designed exclusively for SELV operation in accordance with IEC 60950 / EN 60950/VDE 0805. 7242_en_00 PHOENIX CONTACT 3 FL PSE 2TX Installation and Mounting/Removal Install the PoE module on a clean DIN rail in accordance with EN 60715. Only use corrosion-free DIN rails to prevent contact resistance. In order to prevent the module from slipping on the rail, end brackets can be mounted on both sides of the module. Mounting 1 2 3 Place the module onto the DIN rail from above. The upper holding keyway must be hooked onto the top edge of the DIN rail. Push the module from the front towards the mounting surface. Once the module has been snapped on properly, check that it is fixed securely on the DIN rail. Removal 1 2 3 Pull the locking latch down using a screwdriver, needle-nose pliers or similar. Pull the bottom edge of the module away from the mounting surface. Pull the module diagonally upwards away from the DIN rail. Terminal Assignment and Grounding Connect the DIN rail to protective earth ground using a grounding terminal block. The modules are grounded when they are snapped onto the DIN rail. Connect protective earth ground with low impedance. Connection of the Supply Voltage Warning The FL PSE 2TX module is designed exclusively for SELV operation in accordance with IEC 60950 / EN 60950/VDE 0805. 1 2 3 4 5 6 7 8 Terminal 1 2 3 4 5-8 Meaning Supply voltage +US1 (+24 V DC) GND US1 Supply voltage +US2 (+24 V DC) GND US2 Functional earth ground (optional) US Figure 1 Terminal assignment Diagnostic and Status Indicators Des. US Color Green Green 7242_en_00 Meaning Supply voltage For each PoE port - PoE detection PHOENIX CONTACT 4 FL PSE 2TX Port Assignment There are two port pairs: ports ETH1 and POE1 as well as ports ETH2 and POE2. Pin Assignment of the ETH1/2 Interface Pin 1 2 3 4 5 6 7 8 Assignment Description RX/TX Data RX/TX Data TX/RX Data Not used Not used TX/RX Data Not used Not used Pin Assignment of the PoE1/2 Interface Pin 1 2 3 4 5 6 7 8 Assignment RX/TX RX/TX TX/RX PoE PoE TX/RX PoE PoE Description Data Data Data 48 V DC 48 V DC Data 0 V DC 0 V DC Method of Operation of Power-over-Ethernet Power Ethernet X5 US 24 V X1 48 V Power over Ethernet X2 ETH2 X3 POE2 X4 FL PSE 2TX Ord.-No.2891013 724200001 Figure 2 PoE method for ETH1 <-> PoE1 Midspan Insertion Devices transmitting the data of the active components and simultaneously supplying the Ethernet cables with power operate according to the "midspan insertion" method. Midspan insertion modules can simply be used to retrofit existing network infrastructures or they can be applied when only a small part of the required ports needs to be PoE-compliant. Power-over-Ethernet Performance Classes Class 0 1 2 3 4 7242_en_00 Usage Default Optional Optional Optional Reserved Power Supply 15.4 W 4.0 W 7.0 W 15.4 W 15.4 W Power Outlet 0.44 W up to 12.95 W 0.44 W up to 3.84 W 3.84 W up to 6.49 W 6.49 W up to 12.95 W Reserved PHOENIX CONTACT 5 FL PSE 2TX Length of the Ethernet Cable The length of the entire Ethernet cable per channel must not exceed 100 m. X5 US Host/ Switch X1 Powered Device X2 ETH2 X3 POE2 X4 FL PSE 2TX Ord.-No.2891013 xm 100 m - x m 100 m max. Figure 3 724200002 Length of the Ethernet Cable © PHOENIX CONTACT 02/2006 7242_en_00 PHOENIX CONTACT 6