FL SWITCH SFNT

FL SWITCH SFNT…
Five and Eight-Port Standard Function Ethernet
Switches for Extreme Environments
AUTOMATION
Data Sheet
2665_en_I
1
© PHOENIX CONTACT 2011-06-30
Description
The FL SWITCH SFNT… range of Factory Line switches
can be used for quick and cost-effective Ethernet network
expansion to the field level. These unmanaged switches
allow operation across a wider temperature range than most
switches, allowing networks to expand into process industry
environments, such as oil/gas, chemical, water/wastewater,
wind energy, security, monitoring and some marine
segments. Due to the narrow housing design, the switches
are suitable for use in control cabinets and junction boxes.
The FL SWITCH SFNT… switches support the auto
negotiation function on the RJ45 ports and offer
transmission speeds of 10/100 Mbps. Mixed operation for
the connection of segments with different data transmission
speeds is also supported. The RJ45 ports offer an auto
crossing function, which means it is not necessary to make
a distinction between 1:1 and crossover cables. Unused
RJ45 ports can be fitted with security caps to provide
mechanical protection against unauthorized use.
Fiber optic ports are available in an SC or ST format and
offer speeds of 100 Mbps. The fiber optic ports extend the
segment length to 2000 m or more, depending on the quality
of the fiber optic cable.
2
–
–
–
–
–
–
–
–
–
–
Features and Benefits
-40 to 75°C operating range
Pretagged high priority messages are forwarded before
lower priority messages during periods of high network
traffic
Auto-negotiation and autocross simplify cabling
Couple copper network segments with different bit rates
with automatic detection of the data transmission speed
of 10 or 100 Mbps
Individual LEDs at each port indicate communication
activity and data rate
Redundant power supply capable with local (LED) and
remote (dry contact) alarms to indicate failure of one or
both power supplies
Switch-selectable link diagnostics indicate
disconnected ports via local and remote alarms
Available fiber optic options for extended distance and
electrical noise immunity
Fiber optic ports available in SC or ST formats
Low-cost, low-complexity security by connecting
Layer 1 security elements at the RJ45 ports to restrict
access and tampering (optional)
Please note the different connection directions of the transmission media for five-port switches: copper cables are
connected at the front, glass fiber cables at the bottom.
This data sheet is valid for all products listed on the following page:
Make sure you always use the latest documentation.
It can be downloaded at www.phoenixcontact.net/catalog.
FL SWITCH SFNT…
3
Ordering Data
Description
Type
Order No.
Pcs./Pkt.
Ethernet switch, wide temperature with 5 RJ45 ports for 10/100 Mbps
FL SWITCH SFNT 5TX
2891003
1
Ethernet switch, wide temperature with 8 RJ45 ports for 10/100 Mbps
FL SWITCH SFNT 8TX
2891005
1
Ethernet switch, wide temperature with 4 RJ45 ports and 1 fiber optic
port in SC format, for 10/100 Mbps
FL SWITCH SFNT 4TX/FX
2891004
1
Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic
port in SC format, for 10/100 Mbps
FL SWITCH SFNT 7TX/FX
2891006
1
Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic
port in ST format, for 10/100 Mbps
FL SWITCH SFNT 7TX/FX ST
2891007
1
Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic
ports in SC format, for 10/100 Mbps
FL SWITCH SFNT 6TX/2FX
2891025
1
Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic
ports in ST format, for 10/100 Mbps
FL SWITCH SFNT 6TX/2FX ST
2891026
1
Ethernet switch, wide temperature with 5 RJ45 ports for 10/100 Mbps,
with conformal coating
FL SWITCH SFNT 5TX-C
2891043
1
Ethernet switch, wide temperature with 8 RJ45 ports for 10/100 Mbps,
with conformal coating
FL SWITCH SFNT 8TX-C
2891044
1
Ethernet switch, wide temperature with 4 RJ45 ports and 1 fiber optic
port in SC format, for 10/100 Mbps, with conformal coating
FL SWITCH SFNT 4TX/FX-C
2891045
1
Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic
port in SC format, for 10/100 Mbps, with conformal coating
FL SWITCH SFNT 7TX/FX-C
2891046
1
Ethernet switch, wide temperature with 7 RJ45 ports and 1 fiber optic
port in ST format, for 10/100 Mbps, with conformal coating
FL SWITCH SFNT 7TX/FX ST-C
2891047
1
Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic
ports in SC format, for 10/100 Mbps, with conformal coating
FL SWITCH SFNT 6TX/2FX-C
2891048
1
Ethernet switch, wide temperature with 6 RJ45 ports and 2 fiber optic
ports in ST format, for 10/100 Mbps, with conformal coating
FL SWITCH SFNT 6TX/2FX ST-C
2891049
1
Accessories
Description
Type
Order No.
Pcs./Pkt.
Universal end clamp
E/NS 35 N
0800886
50
Patch angle with 2 ports in CAT 5e
FL PF 2TX CAT5E
2891165
1
Patch angle with 8 ports in CAT 5e
FL PF 8TX CAT5E
2891178
1
Patch angle with 2 ports in CAT 6
FL PF 2TX CAT6
2891068
1
Patch angle with 8 ports in CAT 6
FL PF 8TX CAT6
2891071
1
Patch angle with security elements for 2 ports in CAT 5e
FL PF SEC 2TX
2832687
1
Patch angle with security elements for 8 ports in CAT 5e
FL PF SEC 8TX
2832690
1
Patchbox 8 x RJ45 CAT 5e, pre-assembled, can be retrofitted
FL PBX 8TX
2832496
1
Patch cable, CAT 5, pre-assembled, 0.3 m long
FL CAT5 PATCH 0,3
2832250
10
Patch cable, CAT 5, pre-assembled, 0.5 m long
FL CAT5 PATCH 0,5
2832263
10
Patch cable, CAT 5, pre-assembled, 1.0 m long
FL CAT5 PATCH 1,0
2832276
10
Patch cable, CAT 5, pre-assembled, 1.5 m long
FL CAT5 PATCH 1,5
2832221
10
Patch cable, CAT 5, pre-assembled, 2.0 m long
FL CAT5 PATCH 2,0
2832289
10
Patch cable, CAT 5, pre-assembled, 3.0 m long
FL CAT5 PATCH 3,0
2832292
10
Patch cable, CAT 5, pre-assembled, 5.0 m long
FL CAT5 PATCH 5,0
2832580
10
Patch cable, CAT 5, pre-assembled, 7.5 m long
FL CAT5 PATCH 7,5
2832616
10
Patch cable, CAT 5, pre-assembled, 10.0 m long
FL CAT5 PATCH 10
2832629
10
Security frame for SFN switch and patch fields, green
FL PLUG GUARD, GN
2891615
20
Security frame for SFN switch and patch fields, red
FL PLUG GUARD, RD
2891712
20
Security frame for SFN switch and patch fields, white
FL PLUG GUARD, WH
2891819
20
Security frame for SFN switch and patch fields
FL PORT GUARD
2891220
20
Security frame for SFN switch and patch fields
FL PLUG GUARD KEY
2891327
1
20
Security element for FL CAT patch
FL PATCH SAFE CLIP
2891246
Mounting plate for SFNT… 5 and 8 port switches
FL PA SFNT 5-8
2891012
1
Mounting plate, DIN rail, for SFNT… 5 and 8 port switches
FL DA SFNT 5-8
2891017
1
2665_en_I
PHOENIX CONTACT
2
FL SWITCH SFNT…
4
Technical Data
General Data
Function
Switch/repeater; conforms to standard IEEE 802.3
Latency of the communication processor
8 µs plus frame time
Housing dimensions (width x height x depth)
5-port switch, without connectors
8-port switch, without connectors
30 x 130 x 100 mm
50 x 130 x 100 mm
Weight, without connectors
FL SWITCH SFNT 5TX(-C)
FL SWITCH SFNT 8TX(-C)
FL SWITCH SFNT 4TX/FX(-C)
FL SWITCH SFNT 7TX/FX(-C)
FL SWITCH SFNT 7TX/FX ST(-C)
FL SWITCH SFNT 6TX/2FX(-C)
FL SWITCH SFNT 6TX/2FX ST (-C)
271 g
457 g
276 g
464 g
465 g
484 g
484 g
Operating temperature
-40°C to 75°C
Storage temperature
-40°C to 85°C
Degree of protection
IP20, DIN 40050, IEC 60529
Protection class
Class 3 VDE 0106; IEC 60536
Humidity (operation and storage)
5% to 95%, no condensation
Air pressure (operation)
62 kPa to 108 kPa, 4160 m above sea level
Air pressure (storage)
62 kPa to 108 kPa, 4160 m above sea level
Mounting
NS 35 (EN 60715)
Preferred mounting position
Perpendicular to a standard mounting rail
Connection to protective earth ground
Snapped onto a grounded mounting rail
Supply Voltage (US)
Connection type
Removable, screw-clamp connector
Wire size (solid/stranded/AWG)
0.2 to 2.5 mm² / 0.2 to 2.5 mm² / 24 to 12 AWG
Recommended PE wire size
2.5 mm2
Nominal power supply
24 V DC
Permissible ripple
3.6 Vpp within the permissible voltage range
Permissible voltage range
9 V DC to 32 V DC
Test voltage
500 V DC for one minute
Protection against polarity reversal
Present
Current Consumption and Inrush Current
FL SWITCH SFNT 5TX(-C)
Current Consumption (max) @ 24 V DC
Inrush Current
120 mA
5.0 A for 68 µs
FL SWITCH SFNT 8TX(-C)
153 mA
7.0 A for 30 µs
FL SWITCH SFNT 4TX/FX(-C)
180 mA
8.1 A for 4 µs
FL SWITCH SFNT 7TX/FX(-C)
175 mA
8.0 A for 31 µs
FL SWITCH SFNT 7TX/FX ST(-C)
175 mA
8.0 A for 30 µs
FL SWITCH SFNT 6TX/2FX(-C)
250 mA
11.6 A for 30 µs
FL SWITCH SFNT 6TX/2FX ST(-C)
250 mA
10.8 A for 30 µs
2665_en_I
PHOENIX CONTACT
3
FL SWITCH SFNT…
Interfaces
Total number of RJ45 Ethernet interfaces
4… 8
MAC Address Table Size (Entries)
2K
Properties of RJ45 Ports
Connection format
8-pos. RJ45 female connector on the switch
Connection medium
Twisted-pair cable with a conductor cross section of 0.14 mm2 to 0.22 mm2
Cable impedance
100 Ω
Transmission speed
10/100 Mbps
Maximum network segment length
100 m
Properties of Fiber Optic Ports
Connection format
SC duplex or ST female connector
Fiber type
Multimode
Laser protection
Class 1 according to DIN EN 60825-1:2001-11
Transmission rate
100 Mbps full duplex
Wavelength
1300/1310 nm
Fiber optic segment length
12.1 km glass fiber with F-G 62.5/125 0.7 dB/km F1000
3.3 km glass fiber with F-G 62.5/125 2.6 dB/km F600
7.1 km glass fiber with F-G 50/125 0.7 dB/km F1200
3.1 km glass fiber with F-G 50/125 1.6 dB/km F800
Transmission power (medium type) dynamic (average)
Minimum
Maximum
-23.5 dBm (50/125 µm) / -20 dBm (62.5/125 µm)
-14 dBm (50/125 µm) / -14 dBm (62.5/125 µm)
Transmission power (medium type) static
Minimum
Maximum
-22.5 dBm (50/125 µm) / -19 dBm (62.5/125 µm)
-14 dBm (50/125 µm) / -14 dBm (62.5/125 µm)
Receiver sensitivity
Minimum
Maximum
-31 dBm (dynamic) / -31 dBm (static)
-14 dBm (dynamic) / -14 dBm (static)
Alarm Contacts
Voltage
24 V DC
Current carrying capacity
100 mA maximum including inrush
Mechanical Tests
Shock test according to IEC 60068-2-27
Operation: 25g, 11 ms period, half-sine shock pulse
Storage/transport: 50g, 11 ms period, half-sine shock pulse
Vibration resistance according to IEC 60068-2-6
Operation/storage/transport: 5g, 150 Hz, Criterion 3
Free fall according to IEC 60068-2-32
1m
Conformance With EMC Directives
Developed according to IEC 61000-6-2
IEC 61000-4-2 (ESD)
Contact: ±4 kV, Criterion B
Air: ±8 kV, Criterion B
IEC 61000-4-3 (radiated-noise immunity)
10 V/m, Criterion A
IEC 61000-4-4 (burst)
Ports: ±1 kV, Criterion B
DC power: ±2 kV, Criterion B
IEC 61000-4-5 (surge)
Ports: ±1 kV, Criterion B
DC power: ±500 V, Criterion B
IEC 61000-4-6 (conducted noise immunity)
10 V/m, Criterion A
IEC 61000-4-8 (noise immunity against magnetic fields)
30 A/m, Criterion A
EN 55022 (noise emission)
Class A
2665_en_I
PHOENIX CONTACT
4
FL SWITCH SFNT…
Conformance With Environmental and EMC Directives for Marine Applications1
Developed according to IEC 60945:2002
8.2 Dry Heat
8.3 Damp Heat (including test of insulation resistance)
8.4 Cold
8.7 Vibration
9 Electromagnetic emission
9.2 Conducted emission
9.3 Radiated emission
10.3 Immunity to conducted radio frequency
10.4 Immunity to radiated radio frequencies
10.5 Immunity to fast transients
10.6 Immunity to surges
10.7 Power supply variations
10.8 Power supply failure
10.9 Electrostatic discharge
IEC 60945 Standard magnetic compass
Safe compass distance
Reduced safe distance
1.05 m
0.65 m
IEC 60945 Steering magnetic compass
Safe compass distance
Reduced safe distance
1
0.60 m
0.40 m
Excludes FL SWITCH SFNT…-C devices
Approvals
General
c u ROHS EEE 2002/95/EC, WEEE 2002/96/EC
Hazardous location1
U Class 1, Division 2, Groups A, B, C, D Temp Code T4
installed in minimum IP54 enclosure
Marine1 2
Flxovm
1
Excludes FL SWITCH SFNT…-C devices
2
Excludes SFNT 6TX/2FX and SFNT 6TX/2FX ST devices
2665_en_I
PHOENIX CONTACT
5
FL SWITCH SFNT…
5
5.2
Overview
Power connector
Power connector
Data Transmission Speed LEDs (2 LEDs/Port)
10 Mbps
100 Mbps
LNK/ACT
ON/blinking
ON/blinking
100
OFF
ON
Power LEDs (US) - green
LNK/ACT LED:
ON: indicates an electrical link
FL SWITCH SFNT 4TX/FX
Ord.No. 2891004
1
US
10
0
FL SWITCH SFNT 8TX
Ord.No. 2891005
rm
Ala
2
US
1
US
K/
LN T
AC
2
US
10
0
Flashing: indicates network traffic (at high data
rates the blinking is in a constant rate)
rm
Ala
K/
LN T
AC
K/
LN T
AC
10
0
X1
X1
X2
6
10
0
K/
LN T
AC
/
10
0
K
LN T
AC
Installation
/
K
LN T
AC
10
0
CAUTION:
X2
X3
10
0
K/
LN T
AC
X4
/
10
X3
0
K
LN T
AC
/
K
LN T
AC
10
0
X5
10
0
K/
LN T
AC
X6
10
X4
0
K/
LN T
AC
K/
LN T
AC
100 LED
LNK/ACT
10
0
NOTE:
Port X5
LNK/ACTLED
Security Frame
Figure 1
5.1
The FL SWITCH SFNT… module is designed for
SELV and PELV operation according to
IEC 61140/EN 61140.
X8
X7
100
Only qualified personnel may start up and operate
this device. Qualified personnel are persons
authorized to start up, ground and mark devices,
systems, and equipment according to the
standards of safety technology.
Power Connector, LED Locations and Security
Frame
Install the FL SWITCH SFNT… on a clean NS 35 rail. To
avoid contact resistance use only clean, corrosion-free rails
that meet the EN 60715 standard. End clamps can be
mounted on both sides of the module to stop the modules
from slipping on the rail.
Diagnostic and Status Indicators
Des.
Color
Status
US1 and
US2
green
ON
Supply voltage (US) in
the tolerance range
OFF
Supply voltage (US) too
low
ON
US1 or US2 is too low or
missing
Alarm
red
NOTE:
Meaning
Connect the mounting rail to protective earth
ground using a grounding terminal block. The
modules are grounded when they are snapped
onto the rail. Connect protective earth ground
with low impedance.
6.1
1.
Port link failure
OFF
Normal operation
2.
3.
2665_en_I
Assembly
Place the module onto the rail from above. The upper
holding keyway must be hooked onto the top edge of
the rail.
Push the module from the front towards the mounting
surface.
Once the module has been snapped on properly, check
that it is fixed securely on the rail.
PHOENIX CONTACT
6
FL SWITCH SFNT…
6.2
1.
2.
3.
6.3
Removal
Insert a suitable tool (e.g., needle-nose pliers) into the
arresting latch and pull it down.
Pull the module slightly away from the mounting
surface.
Lift the module from the rail.
Snapping the switch onto a grounded rail connects it to the
ground potential. In an environment particularly prone to
EMI, noise immunity can be increased by an additional lowimpedance connection to protective earth (see Figure 3).
Mounting Plate
The FL PA SFNT 5-8 mounting plate provides a method for
mounting SFNT 5- and 8-port switches to a flat surface in
any orientation. The plate can be mounted on either side of
the switch to allow the network ports to face the proper
direction.
+
–
+
–
FL DA SFNT 5-8 adapter allows installation of the switch on
a DIN rail with a low profile. The adapter also installs on
either side of the switch.
R2
U
S
1
X
9
G
N
D
U
S
2
G
N
D
R
1
R
2
US1 GND US2 GND R1
FL
P
Ord A SF
Da .-No.: NT 5
-8
te
Ma :14.02891
de 5.2 012
in T 01
aiw 0
an
FL
rm
la
A
H
ITC
SW
o.
.N
Odr
2
S
U
1
S
U
SFN
91
28
T
XS
X/F
T 7T
7
00
Figure 3
/
K
IN
L T
C
A
0
/
K
IN
L T
C
A
0
1
Power connections for redundant power
supply
X2
0
0
1
/
K
IN
L T
C
A
X1
0
/
K
IN
L T
C
A
0
1
X4
0
0
1
/
K
IN
L T
C
A
X3
0
/
K
IN
L T
C
A
0
1
X6
0
0
1
/
K
IN
L T
C
A
X5
0
/
K
IN
L T
C
A
0
1
X8
0
0
1
X7
Figure 2
+
–
FL PA SFNT 5-8 Mounting Plate
The dimensions of the FL PA SFNT 5-8 are
shown in Figure 10.
Additional information for the FL PA SFNT 5-8
can be found at
www.phoenixcontact.net/catalog.
6.4
US1 GND US2 GND R1
R2
Power Connection
The switch is designed for SELV and PELV operation at
+24 V DC according to IEC 61140/EN 61140. Only SELV
and PELV according to the defined standards may be used
for supply purposes.
2665_en_I
Figure 4
Power connections for single power supply
PHOENIX CONTACT
7
FL SWITCH SFNT…
Use power conductors between 0.2 - 2.5 mm²
(24 - 12 AWG). Torque connection screws to 0.5 - 0.6 Nm
(5 - 7 lb-in.).
6.5
Alarm Contact
The FL SWITCH SFNT… switch provides contacts (R1, R2)
for remote alarms if a failure is detected. Alarms are
triggered if one or both power supplies fail. An alarm can be
triggered if a port fails. Individual port alarms can be enabled
via a DIP switch located on the bottom of the switch.
6.7
Fiber Optic Connection
Two different types of fiber optic connection are available.
The fiber optic connector(s) are located on the lower front
face of the 8-port models or on the bottom face of the 5-port
models.
The ST connectors are typically individual round connectors
and use a 1/4-turn connection.
The SC connectors have a square interface and the
“conductors” are typically locked together through the
connector.
The alarm relay is a normally closed type. When there are
no faults, the contact is held open. When a fault occurs, the
relay is de-energized to close the contact.
The FL SWITCH SFNT 5... and FL SWITCH SFNT 4... use
a five-position DIP switch. The FL SWITCH SFNT 8..., FL
SWITCH SFNT 7... and FL SWITCH SFNT 6... use an eightposition DIP switch. Each DIP switch position corresponds
to the port number.
TD
RD
ON
OFF
Port
O
N
1 2 3 4 5
1 2 3 4 5
In addition to the remote alarm, failure is also
indicated by the alarm LED On.
Link Monitor Alarm
To enable an alarm, move the appropriate slider to the ON
position.
Failure indication of a fiber optic port can be in
either the RX or TX fiber.
To disable an alarm, move the appropriate slider to the off
position.
DIN Rail clamp
Figure 6
6.6
5-port fiber optic ports (SC connectors)
Ethernet Interface
The FL SWITCH SFNT… has five Ethernet ports on the front
in RJ45 format to which only twisted-pair cables with an
impedance of 100 Ω can be connected. The data
transmission speed is 10/100 Mbps. In addition, every port
has an auto crossing function: it is not necessary to make a
distinction between 1:1 or crossover Ethernet cables.
X5
X6
10
0
K/
LN T
AC
K/
LN T
AC
10
X5
0
X6
10
TD
K/
LN T
AC
K/
LN T
AC
0
10
0
RD
TD
RD
X7
RD
RD
RD
X7
X8
RD
TD
TD
Figure 7
X8
TD
TD
8-Port ST fiber optic ports
RJ45
X5
X6
10
0
K/
LN T
AC
K/
LN T
AC
10
0
RD
2665_en_I
K/
LN T
AC
0
K/
LN T
AC
10
0
RD
X7
Figure 5
X6
10
TD
8 7 6 5
4 3 2 1
n.c. TDn.c. RDn.c. n.c.
TD+ RD+
X5
Figure 8
RD
X7
X8
X8
TD
TD
8-port SC fiber optic ports
RJ45 pin assignment
PHOENIX CONTACT
8
FL SWITCH SFNT…
7
Switching Characteristics
8
Dimensions
Store and Forward
All data telegrams received by the switch are saved and
their validity checked. Invalid or faulty data packets
(> 1522 bytes or CRC errors) and fragments (< 64 bytes)
are rejected. Valid data telegrams are forwarded by the
switch. The switch always forwards the data using the data
transmission speed that is used in the destination network
segment.
14 mm
FL SWITCH SFNT 4TX/FX
Ord.No. 2891004
1
US
10
0
FL SWITCH SFNT 8TX
Ord.No. 2891005
rm
2
US
1
US
Ala
K/
LN T
AC
2
US
10
rm
Ala
0
K/
LN T
AC
K/
LN T
AC
10
0
X1
X1
10
0
K/
LN T
AC
X2
10
0
K/
LN T
AC
K/
LN T
AC
10
0
Multi-Address Function
The switch independently learns the addresses for
termination devices, which are connected via a port, by
evaluating the source addresses in the data telegrams. Only
packets with unknown addresses, with a source address of
this port or with a multicast/broadcast address in the
destination address field are forwarded via the
corresponding port. The switch can store addresses in its
address table with an aging time of 5 minutes. This is
important when more than one termination device is
connected to one or more ports. In this way, several
independent subnetworks can be connected to one switch.
X3
10
0
130 mm
X2
K/
LN T
AC
X3
X4
10
0
K/
LN T
AC
K/
LN T
AC
10
0
X5
10
0
K/
LN T
AC
X6
10
X4
0
K/
LN T
AC
K/
LN T
AC
10
X8
X7
100
LNK/ACT
0
Port X5
30 mm
50 mm
A restart deletes the entire address table.
Depth = 100 mm
The FL SWITCH SFNT… switches are capable of reading
Ethernet packets that have already been assigned a priority
level by a managed switch. In cases of heavy traffic, packets
with a priority level between 4 and 7 are considered high
priority and processed before packets with a priority level
between 0 and 3. After prioritization the packets are
forwarded without modification.
Figure 9
8.1
Housing dimensions
FL PA SFNT 5-8 Mounting Plate
10.5 mm
Quality of Service (QoS): IEEE 802.1P/Q
Ø 5 mm
100.0 mm
130.0 mm
126.4 mm
140.0 mm
Figure 10
2665_en_I
FL PA SFNT 5-8 Dimensions
PHOENIX CONTACT
9
FL SWITCH SFNT…
8.2
FL DA SFNT 5-8 Mounting Plate
115.4 mm
5.45 mm
104.5 mm
2665_en_I
100 mm
76.4 mm
Figure 11
FL DA SFNT 5-8 Dimensions
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00
PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300
www.phoenixcontact.com
10