LAN CABLE HiTESTER 3665-20

LAN CABLE HiTESTER 3665-20
Optical/Telecom Measurement
Network Construction with
One Single Instrument
Wiremap
Detect Split Pairs with Wiring Check
Cable Length
Get NVP-Enhanced Measurement Accuracy
Actual Size
Direction
Identify Up to 21 Cable Destinations
1
Wide
LCD
Screen
Extremely Just connect a cable, and
Intuitive press the TEST button
Check all parameters such as wiremap,
direction and cable length at a glance.
2
Direction (ID No.)
Identify the terminator ID here.
3 Cable Length
1
1
Obtain a record of the entire
length of the cable, or up to
the point where the cable is
damaged.
Wiremap (Wiring Status)
Large PASS/FAIL display, cable type, reason for cable failure and shield condition.
Wiremap
For wiring confirmation and locating broken wires after installation.Quick PASS/FAIL reading helps you complete your work faster.
PASS Display Examples
Both straight-through and crossover cables (10/100BASE,
1000BASE-T and 1000BASE-TX) can be checked.
Straight Cable
Cross Cable
Fully Compatible to
CAT6 LAN Cables
Supersensitive
Detection
Detect the existence of
shields or check for shield integrity.
Shielded
Unshielded
FAIL Display Examples
Reversed
Pins 1 and 2 are reversed.
Caution!
PASS
Transposed
Open
Short
Split Pair
Pins 3 and 6 have been
incorrectly paired with Pins
4 and 5.
Pin 1 is open at a distance 7
meters from the LAN cable
tester.
Pins 1 and 2 are shorted at a
distance 10 meters from the LAN
cable tester.
A very common mistake - twist
pairs Pins 3+6, and Pins 4+5,
have been incorrectly connected.
Can you find
split pairs?
Proper Wiring
LAN cable wires should be connected as shown in the diagram
above, such that Pins 3 and 6 are twisted.
FAIL
Split Pair
A "Split Pair" is detected when Pins 3 and 6 are not twisted and
paired together as shown above.
2
2
Direction
Locate up to 21 unique cable destinations.
Have you ever had trouble
installing additional cables?
Take advantage of the conveniences offered by the
tester's capabilities to check wiring while confirming
multiple cable destinations.
Increased
Efficiency!
You will never need to go back and forth
again just to change the terminators.
Up to 21 terminators can be connected (additional terminators
sold separately.) Convenient for confirming the connection
destinations of multiple cables.
3
Cable Length
Measure for cable length and detect the location of broken or short-circuited wires.
The NVP*setting is a cable-length compensation function that enhances the
accuracy of cable length measurements.
Accuracy with NVP activated:
Increased
n ± 4% rdg. ± 1m
Precision!
(vs.previous HIOKI model: 15% rdg. ±1m)
*
NVP (Nominal Velocity of Propagation) is the ratio of the speed of a signal in the cable relative to the speed of light in a vacuum.
NVP differs according to the type of cable and the manner in which the wire pairs are twisted, so measurement accuracy can be enhanced by setting the NVP value for the particular type of cable to be measured.
n Activating the NVP function is as simple as 1-2-3
Preparation
Prepare a reference cable using a
known length of the same type as that
to be measured (at least 100-meter
length recommended).
1
On the Settings screen,
select “Length Adjust”.
2
Press the TEST button to
measure the (already known)
length of the reference cable.
3
Calibrate the display to the
measured reference cable.
Setting
Finished
How Can Split Pairs Affect the Network?
◆ Communication speed can be suppressed - 100BASE signals may reach only 10BASE speeds.
◆ Excessive communication errors - data transfer may be intermittent or completely inhibited.
◆ Cables miswired in this way are more susceptible to electrical noise.
Split pairs appear to be properly
connected to the untrained eye,
and cannot be detected with continuity
testing.
To properly check LAN cable wiring,
a tester capable of detecting split pairs is indispensable.
OK!
The HIOKI 3665-20 can do the job for you properly and
accurately by also detecting split pairs.
3
n Specifications (@ 23 ±5 °C, 80% RH or less, non-condensating, with battery indicator unlit)
Measurable cables Twisted-pair cable
100 Ω characteristic impedance, shielded and unshielded, CAT 3, 4, 5, 5e and 6
Compatible connectors RJ-45 plugs
Measurement Items
Wiring condition and shielding can be confirmed using the HIOKI TERMINATOR 9690
[Wiremap]
Detectable errors: open, short, reversed, transposed, split pairs and other miswiring
Measurable lengths: 2 to 300 m, 6.6 to 984 ft
[Cable Length]
Measurement accuracy: ±4% rdg. ±1 m, ±4% rdg. ±3.3 ft
Display resolution: 0.1 m
Up to 21 cables can be identified using the supplied TERMINATOR 9690 and optional Models 9690-01 to
[Destination]
9690-04 to test multiple cables simultaneously
128 × 64 dot matrix LCD (with backlight)
Display
Auto Backlight: pressing a button turns the backlight on (it turns off automatically after about 20 seconds)
Beeper: sounds when pressing buttons and when measurement results are displayed
Energy-Saving Mode: enter into energy-saving mode after measurement (and resume when the TEST button is pressed)
Functions
Auto Power Save: the 3665-20 turns off automatically about 10 minutes after the last button press
Battery Check: Battery indicator blinks when voltage falls below 2.4 V
Unit Switch: Select between meters or feet
Compliance
Safety Standard: EN61010-1:2001 Pollution Level 2
EMC Standard: EN61326:1997 + A1:1998 + A2:2001 + A3:2003
Standards
3.3 V peak (between RJ-45 pins)
Allowable Input
Operating Temperature & Humidity 0 to 40 °C, 80% RH or less, non-condensating
Storage Temperature & Humidity –10 to 50 °C, 80% RH or less, non-condensating
Two AA-size (LR6) alkaline batteries
Power Source
Maximum Power Consumption 1.4 VA
Approx. 50 hours (measuring once per minute)
Operating Time
Approx. 85 W × 130 H × 33 D mm, approx. 160 g
Size & Weight
LAN CABLE HiTESTER 3665-20
(Includes TERMINATOR 9690, CARRYING CASE)
n Supplied Accessories
n Options
TERMINATOR 9690
CARRYING CASE
TERMINATOR 9690-01 (IDs 1 to 5)
TERMINATOR 9690-02 (IDs 6 to 10)
TERMINATOR 9690-03 (IDs 11 to 15)
TERMINATOR 9690-04 (IDs 16 to 20)
CARRYING CASE 9249 (stores the 3665-20, 9690 and 9628 together)
LAN CABLE 9628 (1 m long, with RJ-45 plugs)
(Stores the HiTESTER 3665 and TERMINATORs 9690)
TERMINATOR 9690
CARRYING CASE
TERMINATOR 9690-01
CARRYING CASE 9249
(for storing everything together)
LAN CABLE 9628
Note: Company names and Product names appearing in this catalog are trademarks or registered trademarks of various companies.
HIOKI (Shanghai) Sales & Trading Co., Ltd. :
1608-1610 Shanghai Times Square Office, 93 Huai Hai Zhong Road,
Shanghai, P.R.China POSTCODE: 200021
TEL +86-21-6391-0090/0092 FAX +86-21-6391-0360
http://www.hioki.cn / E-mail: [email protected]
HEAD OFFICE :
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 / FAX +81-268-28-0568
http://www.hioki.co.jp / E-mail: [email protected]
HIOKI USA CORPORATION :
6 Corporate Drive, Cranbury, NJ 08512 USA
TEL +1-609-409-9109 / FAX +1-609-409-9108
http://www.hiokiusa.com / E-mail: [email protected]
DISTRIBUTED BY
Beijing Office :
TEL +86-10-5867-4080/4081 FAX +86-10-5867-4090
E-mail: [email protected]
Guangzhou Office :
TEL +86-20-38392673/2676 FAX +86-20-38392679
E-mail: [email protected]
HIOKI INDIA PRIVATE LIMITED :
Khandela House, 24 Gulmohar Colony Indore 452 018 (M.P.), India
TEL +91-731-4223901, 4223902 FAX +91-731-4223903
http://www.hioki.in / E-mail: [email protected]
All information correct as of Jul. 14, 2010. All specifications are subject to change without notice.
3665E3-07M