AD ADP2147

Compact, 800 mA, 3 MHz,
Simple DVS, Buck Regulator
ADP2147
FEATURES
GENERAL DESCRIPTION
Input voltage: 2.3 V to 5.5 V
Peak efficiency: 95%
3 MHz fixed frequency operation
Low quiescent current: 23 μA
Ultralow shutdown current: 0.2 μA (typical)
VSEL pin for simple dynamic voltage scaling (DVS)
100% duty cycle low dropout mode
Internal synchronous rectifier, compensation, and soft start
Current overload and thermal shutdown protection
Small, 6-ball, 1 mm × 1.5 mm WLCSP package
The ADP2147 is a high efficiency, low quiescent current, stepdown (buck) dc-to-dc regulator with an output voltage that can
be switched between two different settings under the control of
a select pin. The total solution requires only three tiny external
components.
APPLICATIONS
The ADP2147 runs on input voltages of 2.3 V to 5.5 V, which
allows for single lithium or lithium polymer cells, multiple
alkaline or NiMH cells, PCMCIA, USB, and other standard
power sources. The maximum load current of 800 mA is
achievable across the input voltage range.
The buck regulator automatically switches operating modes,
depending on the load current level, to maximize efficiency. At
high output loads, the buck regulator operates in PWM mode.
When the load current falls below a predefined threshold, the
regulator operates in power save mode (PSM), improving the
light-load efficiency.
PDAs and palmtop computers
Wireless handsets
Digital audio portable media players
Digital cameras, GPS navigation units
Low power portable medical equipment
The ADP2147 is available with fixed output voltages from 0.8 V
to 3.3 V. All versions include an internal power switch and
synchronous rectifier for minimal external part count and high
efficiency. The ADP2147 has an internal soft start and is
internally compensated. During logic controlled shutdown, the
input is disconnected from the output, and the ADP2147 draws
less than 0.2 μA (typical) from the power source.
Other key features include undervoltage lockout to prevent deep
battery discharge and soft start to prevent input current overshoot at startup. The ADP2147 is available in a 6-ball WLCSP.
TYPICAL APPLICATIONS CIRCUIT
2.3V TO 5.5V
1.0µH
VIN
SW
4.7µF
VOUT
4.7µF
ADP2147
ON
OFF
EN
VOUT
VOUT_H
VSEL
GND
09885-001
VOUT_L
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2011 Analog Devices, Inc. All rights reserved.
ADP2147
TABLE OF CONTENTS
Features .............................................................................................. 1 Enable/Shutdown ....................................................................... 11 Applications....................................................................................... 1 Simple Dynamic Voltage Scaling (DVS) ................................. 12 General Description ......................................................................... 1 Short-Circuit Protection............................................................ 12 Typical Applications Circuit............................................................ 1 Undervoltage Lockout ............................................................... 12 Revision History ............................................................................... 2 Thermal Protection.................................................................... 12 Specifications..................................................................................... 3 Soft Start ...................................................................................... 12 Input and Output Capacitor, Recommended
Specifications ................................................................................ 3 Current Limit.............................................................................. 12 Absolute Maximum Ratings............................................................ 4 Applications Information .............................................................. 13 Thermal Data ................................................................................ 4 External Component Selection ................................................ 13 Thermal Resistance ...................................................................... 4 Thermal Considerations............................................................ 14 ESD Caution.................................................................................. 4 PCB Layout Guidelines.............................................................. 14 Pin Configuration and Function Descriptions............................. 5 Evaluation Board ............................................................................ 15 Typical Performance Characteristics ............................................. 6 Evaluation Board Layout........................................................... 15 Theory of Operation ...................................................................... 11 Outline Dimensions ....................................................................... 16 Control Scheme .......................................................................... 11 Ordering Guide .......................................................................... 16 100% Duty Operation................................................................ 12 PWM Mode................................................................................. 11 Power Save Mode........................................................................ 11 REVISION HISTORY
5/11—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADP2147
SPECIFICATIONS
VIN = 3.6 V, VOUT = 0.8 V to 3.3 V, TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications,
unless otherwise noted. All limits at temperature extremes are guaranteed via correlation using standard statistical quality control (SQC).
Table 1.
Parameter
INPUT CHARACTERISTICS
Input Voltage Range
Undervoltage Lockout Threshold
OUTPUT CHARACTERISTICS
Output Voltage Accuracy
Line Regulation
Load Regulation
Test Conditions/Comments
Min
SW CHARACTERISTICS
SW On Resistance
Current Limit
ENABLE/VSEL CHARACTERISTICS
Input High Threshold
Input Low Threshold
Input Leakage Current
Max
Unit
2.15
5.5
2.3
2.25
V
V
V
+2
+2.5
0.25
−0.95
%
%
%/V
%/A
100
mA
2.3
VIN rising
VIN falling
2.00
PWM mode, VSEL = Low
PWM mode, VSEL = High
VIN = 2.3 V to 5.5 V, PWM mode
ILOAD = 0 mA to 800 mA
−2
−2.5
PWM TO POWER SAVE MODE CURRENT THRESHOLD
INPUT CURRENT CHARACTERISTICS
DC Operating Current
Shutdown Current
Typ
ILOAD = 0 mA, device not switching
EN = 0 V, TA = TJ = −40°C to +85°C
23
0.2
30
1.0
μA
μA
pFET
nFET
pFET switch peak current limit
155
115
1500
240
200
1650
mΩ
mΩ
mA
0
0.4
+1
V
V
μA
3.0
3.4
1100
1.2
EN = VSEL = 0 V to 3.6 V
OSCILLATOR FREQUENCY
−1
2.6
MHz
START-UP TIME
250
μs
THERMAL CHARACTERISTICS
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
150
20
°C
°C
INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS
TA = −40°C to +125°C, unless otherwise specified. All limits at temperature extremes are guaranteed via correlation using standard
statistical quality control (SQC).
Table 2.
Parameter
MINIMUM INPUT AND OUTPUT CAPACITANCE
CAPACITOR ESR
Symbol
CMIN
RESR
Rev. 0 | Page 3 of 16
Min
4.7
0.001
Typ
Max
1
Unit
μF
Ω
ADP2147
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
VIN, EN, VSEL
VOUT, SW to GND
Temperature Range
Operating Ambient
Operating Junction
Storage Temperature
Lead Temperature Range
Soldering (10 sec)
Vapor Phase (60 sec)
Infrared (15 sec)
ESD Model
Human Body
Charged Device
Machine
Rating
−0.4 V to +6.5 V
−1.0 V to (VIN + 0.2 V)
−40°C to +85°C
−40°C to +125°C
−65°C to +150°C
−65°C to +150°C
300°C
215°C
220°C
±1500 V
±500 V
±100 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. These are stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL DATA
Junction-to-ambient thermal resistance (θJA) of the package is
based on modeling and calculation using a 4-layer board. The
junction-to-ambient thermal resistance is highly dependent on
the application and board layout. In applications where high
maximum power dissipation exists, close attention to thermal
board design is required. The value of θJA may vary, depending on
PCB material, layout, and environmental conditions. The specified
values of θJA are based on a 4-layer, 4 in. × 3 in. circuit board. Refer
to JEDEC JESD 51-9 for detailed information pertaining to board
construction. For additional information, see the AN-617
Application Note, MicroCSP™ Wafer Level Chip Scale Package.
ΨJB is the junction-to-board thermal characterization parameter
measured in units of °C/W. The package ΨJB is based on modeling
and calculation using a 4-layer board. The JESD51-12, Guidelines
for Reporting and Using Package Thermal Information, states that
thermal characterization parameters are not the same as thermal
resistances. ΨJB measures the component power flowing through
multiple thermal paths rather than through a single path, which
is the procedure for measuring thermal resistance, θJB. Therefore, ΨJB thermal paths include convection from the top of the
package as well as radiation from the package, factors that make
ΨJB more useful in real-world applications than θJB. Maximum
junction temperature (TJ) is calculated from the board temperature
(TB) and power dissipation (PD) using the formula:
TJ = TB + (PD × ΨJB)
Refer to JEDEC JESD51-8 and JESD51-12 for more detailed
information about ΨJB.
Absolute maximum ratings apply individually only, not in
combination.
The ADP2147 can be damaged if the junction temperature limit is
exceeded. Monitoring ambient temperature does not guarantee
that the junction temperature (TJ) is within the specified
temperature limit. In applications with high power dissipation
and poor thermal resistance, the maximum ambient temperature
may need to be derated. In applications with moderate power
dissipation and low printed circuit board (PCB) thermal
resistance, the maximum ambient temperature can exceed the
maximum limit if the junction temperature is within specification
limits. The junction temperature (TJ) of the device is dependent
on the ambient temperature (TA), the power dissipation of the
device (PD), and the junction-to-ambient thermal resistance of the
package (θJA). Maximum junction temperature (TJ) is calculated
from the ambient temperature (TA) and power dissipation (PD)
using the following formula:
THERMAL RESISTANCE
θJA and ΨJB are specified for the worst-case conditions, that is, a
device soldered in a circuit board for surface-mount packages.
Table 4. Thermal Resistance
Package Type
6-Ball WLCSP
ESD CAUTION
TJ = TA + (PD × θJA)
Rev. 0 | Page 4 of 16
θJA
170
ΨJB
80
Unit
°C/W
ADP2147
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
BALL A1
INDICATOR
1
2
VIN
EN
SW
VSEL
A
B
GND VOUT
C
TOP VIEW
(BALL SIDE DOWN)
Not to Scale
09885-002
ADP2147
Figure 2. Pin Configuration (Top View)
Table 5. Pin Function Descriptions
Pin No.
A1
Mnemonic
VIN
B1
SW
C1
A2
B2
GND
EN
VSEL
C2
VOUT
Description
Power Source Input. VIN is the source of the pFET high-side switch. Bypass VIN to GND with a 4.7 μF or greater
capacitor as close to the ADP2147 as possible.
Switch Node Output. SW is the drain of the P-channel MOSFET switch and N-channel synchronous rectifier.
Connect the output LC filter between SW and the output voltage.
Ground. Connect the input and output capacitors to GND.
Buck Activation. To turn on the buck, set EN to high. To turn off the buck, set EN to low.
Voltage Select Input for Simple Dynamic Voltage Scaling (DVS). Drive VSEL low to switch the VOUT pin to the
default voltage setting. Drive VSEL high to switch VOUT to the alternate voltage setting.
Output Voltage Sensing Input.
Rev. 0 | Page 5 of 16
ADP2147
TYPICAL PERFORMANCE CHARACTERISTICS
VIN = 3.6 V, TA = 25°C, VEN = VIN, unless otherwise noted.
1.825
100
VIN = 2.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.5V
90
1.815
80
60
VOUT (V)
EFFICIENCY (%)
70
50
40
1.805
1.795
30
VIN = 2.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.5V
0.01
0.1
1
IOUT (A)
1.775
Figure 3. Efficiency vs. Load Current, Across Input Voltage,
VOUT = 1.8 V
0
0.1
0.2
0.3
0.4
IOUT (A)
0.5
0.6
0.815
90
VIN = 2.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.5V
0.810
80
0.805
70
60
VOUT (V)
EFFICIENCY (%)
0.8
Figure 6. Load Regulation Across Input Voltage, VOUT = 1.8 V
100
50
40
30
0.800
0.795
0.790
VIN = 2.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.5V
10
0.01
0.1
0.785
1
IOUT (A)
0.780
09885-005
20
0
0.001
0.7
0
0.1
0.2
0.3
0.4
IOUT (A)
0.5
0.6
0.7
0.8
09885-008
0
0.001
09885-006
10
1.785
09885-003
20
Figure 7. Load Regulation Across Input Voltage, VOUT = 0.8 V
Figure 4. Efficiency vs. Load Current, Across Input Voltage,
VOUT = 0.8 V
100
3.378
90
3.358
80
VIN = 3.9V
VIN = 4.2V
VIN = 5.5V
3.338
3.318
VOUT (V)
60
50
40
30
3.258
VIN = 3.9V
VIN = 4.2V
VIN = 5.5V
10
0.01
0.1
IOUT (A)
3.238
1
3.218
0
0.1
0.2
0.3
0.4
IOUT (A)
0.5
0.6
0.7
0.8
Figure 8. Load Regulation Across Input Voltage, VOUT = 3.3 V
Figure 5. Efficiency vs. Load Current, Across Input Voltage,
VOUT = 3.3 V
Rev. 0 | Page 6 of 16
09885-009
20
0
0.001
3.298
3.278
09885-007
EFFICIENCY (%)
70
ADP2147
3.5
350
+25°C
+85°C
+125°C
–40°C
3.4
3.3
250
3.2
FREQUENCY (MHz)
–40°C
+25°C
+125°C
300
RDSON (mΩ)
3.1
3.0
2.9
2.8
200
150
100
2.7
0.2
0.3
0.4
IOUT (A)
0.5
0.6
0
2.3
09885-010
2.5
0.1
0.7
2.8
3.3
3.8
4.3
INPUT VOLTAGE (V)
250
3.4
VIN = 2.3V
VIN = 3.6V
3.3
VIN = 4.2V
VIN = 5.5V
5.3
Figure 12. RDSON PFET vs. Input Voltage, Across Temperature
Figure 9. Frequency vs. Output Current, Across Temperature,
VOUT = 1.8 V
3.5
4.8
09885-036
50
2.6
–40°C
+25°C
+125°C
200
RDSON (mΩ)
FREQUENCY (MHz)
3.2
3.1
3.0
2.9
150
100
2.8
50
2.7
0.2
0.3
0.4
IOUT (A)
0.5
0.6
0
2.3
09885-011
2.5
0.1
0.7
Figure 10. Frequency vs. Output Current, Across Supply Voltage,
VOUT = 1.8 V
2.8
T
IOUT = 100µA
IOUT = 25mA
IOUT = 500mA
4.8
5.3
SW
4
60
VOUT
50
1
40
30
IOUT
20
0
2.3
2.8
3.3
3.8
4.3
INPUT VOLTAGE (V)
4.8
5.3
CH1 100mV
Figure 11. Output Voltage Ripple vs. Input Voltage,
Across Output Current, VOUT = 1.8 V
CH2 250mA Ω
CH4 5.00V
M 40.0µs A CH2
215mA
T 26.00%
Figure 14. Response to Load Transient, 150 mA to 500 mA,
VOUT = 1.8 V
Rev. 0 | Page 7 of 16
09885-014
2
10
09885-034
OUTPUT VOLTAGE (mV)
70
3.8
4.3
INPUT VOLTAGE (V)
Figure 13. RDSON NFET vs. Input Voltage, Across Temperature
90
80
3.3
09885-037
2.6
ADP2147
T
T
SW
SW
4
4
VOUT
VOUT
1
1
IOUT
IOUT
2
CH2 250mA Ω
CH4 5.00V
M 40.0µs A CH2
215mA
T 26.00%
CH1 100mV
09885-015
CH1 100mV
Figure 15. Response to Load Transient, 50 mA to 200 mA,
VOUT = 1.8 V
M 40.0µs A CH2
CH2 250mA Ω
CH4 5.00V
275mA
T 26.00%
09885-018
2
Figure 18. Response to Load Transient, 150 mA to 500 mA,
VOUT = 3.3 V
T
T
SW
SW
4
4
VOUT
VOUT
1
1
IOUT
IOUT
2
CH2 250mA Ω
CH4 5.00V
M 40.0µs A CH2
215mA
T 26.00%
CH1 100mV
09885-016
CH1 100mV
Figure 16. Response to Load Transient, 150 mA to 500 mA,
VOUT = 0.8 V
M 40.0µs A CH2
CH2 100mA Ω
CH4 5.00V
114mA
T 26.00%
09885-019
2
Figure 19. Response to Load Transient, 50 mA to 200 mA,
VOUT = 3.3 V
T
T
SW
VIN
4
VOUT
1
IOUT
VOUT
1
2
CH2 100mA Ω
CH4 5.00V
M 40.0µs A CH2
T 26.00%
134mA
CH1 20.0mV
CH3 1.00V
09885-017
CH1 100mV
M 40.0µs
T
A CH3
–84.0000µs
4.50V
09885-020
3
Figure 20. Response to Line Transient, VOUT = 3.3 V, VIN = 4.0 V to 4.8 V
Figure 17. Response to Load Transient, 50 mA to 200 mA, VOUT = 0.8 V
Rev. 0 | Page 8 of 16
ADP2147
T
T
SW
VIN
4
IIN
2
VOUT
VOUT
1
1
EN
M 40.0µs
T
A CH3
4.50V
–84.0000µs
CH1 1.00V Ω
CH3 5.00V
09885-021
CH1 20.0mV
CH3 1.00V
CH2 500mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.50V
T 10.40%
09885-023
31
3
Figure 24. Startup, VOUT = 0.8 V, IOUT = 10 mA
Figure 21. Response to Line Transient, VOUT = 0.8 V,
VIN = 4.0 V to 4.8 V
T
T
SW
VIN
4
IIN
2
VOUT
VOUT
1
1
3
31
T
A CH3
4.50V
–84.0000µs
CH1 5.00V Ω
CH3 5.00V
CH2 500mA Ω
CH4 5.00V
M 40.0µs
A CH3
2.50V
09885-024
M 40.0µs
09885-033
CH1 20.0mV
CH3 1.00V
3.80mV
09885-025
EN
T 10.40%
Figure 25. Startup, VOUT = 3.3 V, IOUT = 10 mA
Figure 22. Response to Line Transient, VOUT = 1.8 V,
VIN = 4.0 V to 4.8 V
T
SW
SW
T
4
IIN
4
IL
2
2
VOUT
VOUT
1
1
EN
31
CH2 500mA Ω
CH4 5.00V
M 40.0µs
A CH3
T 10.40%
2.50V
CH1 10.0mVΩ
09885-022
CH1 2.00V Ω
CH3 5.00V
CH2 500mA Ω
CH4 2.00V
M 1.00µs A CH1
T 50.00%
Figure 26. Typical Waveform, VOUT = 1.8 V, PSM Mode, IOUT = 10 mA
Figure 23. Startup, VOUT = 1.8 V, IOUT = 10 mA
Rev. 0 | Page 9 of 16
ADP2147
T
SW
T
1
4
IL
2
VOUT
1
CH2 500mA Ω
CH4 2.00V
M 40.0µs
A CH4
1.32V
T 50.00%
CH1 100mV
09885-026
CH1 10.0mVΩ
Figure 27. Typical Waveform, VOUT = 1.8 V, PWM Mode, IOUT = 200 mA
CH2 2.00V
110
1.8V,
1.8V,
1.8V,
1.72V
Figure 30. VSEL Change Triggering VOUT Transition from 1.275 V to 0.981 V,
ILOAD = 10 mA
130
120
M 40.0µs
A CH2
T
79.64µs
09885-130
2
T
VIN = 5.5V, AUTO
VIN = 3.6V, AUTO
VIN = 2.3V, AUTO
100
1
VOUT RIPPLE (mV)
90
80
70
60
50
40
30
2
20
0.01
0.1
1
IOUT (A)
CH1 100mV
09885-028
0
0.001
Figure 28. VOUT Peak-to-Peak Ripple vs. Output Current, VOUT = 1.8 V
CH2 2.00V
M 40.0µs
T 50.20%
A CH2
1.76V
09885-131
10
Figure 31. VSEL Change Triggering VOUT Transition from 0.981 V to1.275 V,
ILOAD = 200 mA
T
T
1
1
CH2 2.00V
M 40.0µs
A CH2
T
–1.966µs
1.72V
09885-129
CH1 100mV
CH1 100mV
Figure 29. VSEL Change Triggering VOUT Transition from 0.981 V to 1.275 V,
ILOAD = 10 mA
CH2 2.00V
M 40.0µs
T 30.00%
A CH2
1.76V
09885-132
2
2
Figure 32. VSEL Change Triggering VOUT Transition from1.275 V to 0.981 V, ILOAD
= 200 mA
Rev. 0 | Page 10 of 16
ADP2147
THEORY OF OPERATION
PWM
COMP
GM ERROR
AMP
SOFT START
VIN
ILIMIT
VOUT
PSM
COMP
PWM/
PSM
CONTROL
LOW
CURRENT
OSCILLATOR
SW
DRIVER
AND
ANTISHOOTTHROUGH
UNDERVOLTAGE
LOCKOUT
VSEL
GND
09885-027
THERMAL
SHUTDOWN
ADP2147
EN
Figure 33. Functional Block Diagram
The ADP2147 is a step-down dc-to-dc regulator that uses a
fixed frequency and high speed current-mode architecture.
The high switching frequency and tiny 6-ball WLCSP package
enable a small step-down dc-to-dc regulator solution.
The ADP2147 operates with an input voltage of 2.3 V to 5.5 V
and regulates an output voltage down to 0.8 V.
CONTROL SCHEME
The ADP2147 operates with a fixed frequency, current-mode
PWM control architecture at medium to high loads for high
efficiency but shifts to a power save mode control scheme at
light loads to lower the regulation power losses. When operating in
PWM mode, the duty cycle of the integrated switches is adjusted
and regulates the output voltage. When operating in power save
mode at light loads, the output voltage is controlled in a hysteretic manner, with higher VOUT ripple. During part of this time,
the converter is able to stop switching and enters an idle mode,
which improves conversion efficiency.
PWM MODE
In PWM mode, the ADP2147 operates at a fixed frequency of
3 MHz, set by an internal oscillator. At the start of each oscillator
cycle, the pFET switch is turned on, sending a positive voltage
across the inductor. Current in the inductor increases until the
magnitude of the current sense signal crosses the peak inductor
current threshold. This turns off the pFET switch and turns on the
nFET synchronous rectifier, which sends a negative voltage across
the inductor, causing the inductor current to decrease. The
synchronous rectifier stays on for the rest of the cycle.
POWER SAVE MODE
The ADP2147 smoothly transitions to the power save mode of
operation when the load current decreases below the power
save mode current threshold. When the ADP2147 enters power
save mode, an offset is induced in the PWM regulation level,
which makes the output voltage rise. When the output voltage
reaches a level approximately 1.5% above the PWM regulation
level, PWM operation turns off. At this point, both power
switches are off, and the ADP2147 enters idle mode. COUT
discharges until VOUT falls to the PWM regulation voltage, at
which point the device drives the inductor to cause VOUT to rise
again to the upper threshold. This process is repeated for as long as
the load current is below the power save mode current
threshold.
Power Save Mode Current Threshold
The power save mode current threshold is set to 100 mA. The
ADP2147 employs a scheme that ensures that this current is
accurately controlled and independent of VIN and VOUT levels.
The control scheme also ensures that there is very little hysteresis
between the power save mode current threshold and that of the
PWM mode. The power save mode current threshold is optimized for excellent efficiency across all load currents.
ENABLE/SHUTDOWN
The ADP2147 starts operating with soft start when the EN pin
is toggled from logic low to logic high. Pulling the EN pin low
forces the device into shutdown mode, reducing the supply
current to 0.2 μA (typical).
The ADP2147 regulates the output voltage by adjusting the peak
inductor current threshold.
Rev. 0 | Page 11 of 16
ADP2147
SIMPLE DYNAMIC VOLTAGE SCALING (DVS)
The ADP2147 has a VSEL pin that allows the user to force the
output voltage to change from one level (the default VOUT
setting) when VSEL is low and to another level (the alternate
VOUT setting) when VSEL is high. Transition between VOUT
levels is achieved within 40 μs when VOUT is commanded to go
from a lower voltage to a higher voltage. When VOUT is commanded to go from a higher VOUT voltage to a lower one, the
transition time depends on the load current present at that time.
SHORT-CIRCUIT PROTECTION
The ADP2147 includes frequency foldback to prevent output
current runaway on a hard short. When the voltage at the
feedback pin falls below half the target output voltage, indicating the possibility of a hard short at the output, the switching
frequency is reduced to half the internal oscillator frequency.
The reduction in the switching frequency allows more time for
the inductor to discharge, preventing a runaway of output current.
UNDERVOLTAGE LOCKOUT
To protect against battery discharge, undervoltage lockout
(UVLO) circuitry is integrated on the ADP2147. If the input
voltage drops below the 2.15 V UVLO threshold, the ADP2147
shuts down, and both the power switch and the synchronous
rectifier turn off. When the voltage rises above the UVLO
threshold, the soft start period is initiated, and the part is
enabled.
THERMAL PROTECTION
In the event that the ADP2147 junction temperature rises above
150°C, the thermal shutdown circuit turns off the regulator.
Extreme junction temperatures can be the result of high current
operation, poor circuit board design, or high ambient temperature.
A 20°C hysteresis is included so that when thermal shutdown
occurs, the ADP2147 does not return to operation until the onchip temperature drops below 130°C. When coming out of
thermal shutdown, a soft start is initiated.
SOFT START
The ADP2147 has an internal soft start function that ramps the
output voltage in a controlled manner upon startup, thereby
limiting the inrush current. The soft start minimizes input
voltage drop when a battery or a high impedance power source is
connected to the regulator’s input.
After the EN pin is driven high, internal circuits begin to power
up. Start-up time in the ADP2147 is the measure of when the
output is in regulation after the EN pin is driven high. Start-up
time consists of the power-up time plus the soft start time.
CURRENT LIMIT
The ADP2147 has protection circuitry to limit the amount of
positive current flowing through the PFET switch and the
synchronous rectifier. The positive current limit on the power
switch controls the amount of current that can flow from the
power source to the output. The negative current limit prevents
the inductor current from reversing direction and flowing out
of the load.
100% DUTY OPERATION
With a drop in VIN or with an increase in ILOAD, the ADP2147
eventually reaches a limit where, even with the pFET switch on
100% of the time, VOUT drops below the desired output voltage.
At this limit, the ADP2147 smoothly transitions to a mode
where the PFET switch stays on 100% of the time. When the input
conditions change again and the required duty cycle falls, the
ADP2147 immediately restarts PWM regulation without
allowing overshoot on VOUT.
Rev. 0 | Page 12 of 16
ADP2147
APPLICATIONS INFORMATION
EXTERNAL COMPONENT SELECTION
Trade-offs between performance parameters such as efficiency
and transient response can be made by varying the choice of
external components in the applications circuit, as shown in
Figure 1.
Inductor
The high switching frequency of the ADP2147 allows for the
selection of small chip inductors. For best performance, use
inductor values between 0.7 μH and 3 μH. Recommended
inductors are shown in Table 6.
The peak-to-peak inductor current ripple is calculated using
the following equation:
CEFF = COUT × (1 − TEMPCO) × (1 − TOL)
where:
CEFF is the effective capacitance at the operating voltage.
TEMPCO is the worst-case capacitor temperature coefficient.
TOL is the worst-case component tolerance.
where:
fSW is the switching frequency.
L is the inductor value.
The minimum dc current rating of the inductor must be greater
than the inductor peak current. The inductor peak current is
calculated using the following equation:
In this example, the worst-case temperature coefficient (TEMPCO)
over −40°C to +85°C is assumed to be 15% for an X5R dielectric.
The tolerance of the capacitor (TOL) is assumed to be 10%, and
COUT is 4.0466 μF at 1.8 V, as shown in Figure 34.
Substituting these values in the equation yields
I RIPPLE
2
CEFF = 4.0466 μF × (1 − 0.15) × (1 − 0.1) = 3.0956 μF
Inductor conduction losses are caused by the flow of current
through the inductor, which has an associated internal DCR.
Larger sized inductors have smaller DCR, which may decrease
inductor conduction losses. Inductor core losses are related to
the magnetic permeability of the core material. Because the
ADP2147 is a high switching frequency dc-to-dc regulator,
shielded ferrite core material is recommended for its low core
losses and low electromagnetic interference (EMI). Table 6
shows the suggested inductors that can be used for different
output current requirements; several inductors are also listed to
minimize PCB space for small current applications.
To guarantee the performance of the ADP2147, it is imperative
that the effects of dc bias, temperature, and tolerances on the
behavior of the capacitors be evaluated for each application.
6
5
Table 6. Suggested 1.0 μH Inductors
Vendor
Murata
Coilcraft®
Toko
TDK
Taiyo Yuden
Model
LQM2MPN1R0NG0B
LQM18PN1R0
EPL2014-102ML
0603LS-102
MDT2520-CN
GLFR1608T1R0M-LR
CBMF1608T1R0M
Dimensions
(mm)
2.0 × 1.6 × 0.9
1.6 × 0.8 × 0.33
2.0 × 2.0 × 1.4
1.8 × 1.27 × 1.1
2.5 × 2.0 × 1.2
1.6 × 0.8 × 0.8
1.6 × 0.8 × 0.8
ISAT
(mA)
1400
700
900
400
1800
360
290
DCR
(mΩ)
85
52
59
81
100
80
90
4
3
2
1
0
0
1
2
3
4
DC BIAS VOLTAGE (V)
5
6
09885-029
I PEAK = I LOAD ( MAX ) +
The worst-case capacitance, accounting for capacitor variation
over temperature, component tolerance, and voltage, is
calculated using the following equation:
CAPACITANCE (µF)
I RIPPLE
V
× (VIN − VOUT )
= OUT
VIN × f SW × L
Ceramic capacitors are manufactured with a variety of dielectrics,
each with different behavior over temperature and applied voltage.
Capacitors must have a dielectric adequate to ensure the
minimum capacitance over the necessary temperature range
and dc bias conditions. X5R or X7R dielectrics with a voltage
rating of 6.3 V or 10 V are recommended for best performance.
Y5V and Z5U dielectrics are not recommended for use with any
dc-to-dc regulator because of their poor temperature and dc bias
characteristics.
Figure 34. Typical Capacitor Performance
The peak-to-peak output voltage ripple for the selected output
capacitor and inductor values is calculated using the following
equation:
Output Capacitor
Increasing the value of the output capacitor reduces the output
voltage ripple and improves load transient response. When
choosing the capacitor value, it is also important to account for
the loss of capacitance due to dc output voltage bias.
Rev. 0 | Page 13 of 16
V RIPPLE =
V IN
(2π × f SW ) × 2 × L × C OUT
=
I RIPPLE
8 × f SW × C OUT
ADP2147
Capacitors with lower equivalent series resistance (ESR) are
preferred to guarantee low output voltage ripple, as shown in
the following equation:
ESRCOUT ≤
VRIPPLE
I RIPPLE
The effective capacitance needed for stability, which includes
temperature and dc bias effects, is 3 μF.
Table 7. Suggested 4.7 μF Capacitors
Vendor
Murata
Taiyo Yuden
TDK
Type
X5R
X5R
X5R
Model
GRM188R60J475
JMK107BJ475
C1608X5R0J475
Case
Size
0603
0603
0603
Voltage
Rating (V)
6.3
6.3
6.3
Input Capacitor
Higher value input capacitors help to reduce the input voltage
ripple and improve transient response. Maximum input
capacitor current is calculated using the following equation:
I CIN ≥ I LOAD ( MAX )
VOUT (VIN − VOUT )
VIN
To minimize supply noise, place the input capacitor as close to
the VIN pin of the ADP2147 as possible. As with the output
capacitor, a low ESR capacitor is recommended. The list of
recommended capacitors is shown in Table 8.
Table 8. Suggested 4.7 μF Capacitors
Vendor
Murata
Taiyo Yuden
TDK
Type
X5R
X5R
X5R
Model
GRM188R60J475
JMK107BJ475
C1608X5R0J475
Case
Size
0603
0603
0603
Voltage
Rating (V)
6.3
6.3
6.3
thermal shutdown. The regulator recovers when the junction
temperature falls below 130°C.
The junction temperature of the die is the sum of the ambient
temperature of the environment and the temperature rise of the
package due to power dissipation, as shown in the following
equation:
TJ = TA + TR
where:
TJ is the junction temperature.
TA is the ambient temperature.
TR is the rise in temperature of the package due to power
dissipation.
The package’s rise in temperature is directly proportional to the
power dissipation in the package. The proportionality constant
for this relationship is the thermal resistance from the junction
of the die to the ambient temperature, as shown in the following
equation:
TR = θJA × PD
where:
TR is the rise in temperature of the package.
θJA is the thermal resistance from the junction of the die to the
ambient temperature of the package.
PD is the power dissipation in the package.
PCB LAYOUT GUIDELINES
Poor layout can affect the ADP2147 performance, causing EMI
and electromagnetic compatibility problems, ground bounce,
and voltage losses. Poor layout can also affect regulation and
stability. To implement a good layout, use the following rules:
•
•
THERMAL CONSIDERATIONS
Because of the high efficiency of the ADP2147, only a small
amount of power is dissipated inside the ADP2147 package, which
reduces thermal constraints of the design.
However, in applications with maximum loads at high ambient
temperature, low supply voltage, and high duty cycle, the heat
dissipated in the package is high enough that it may cause the
junction temperature of the die to exceed the 125°C maximum.
If the junction temperature exceeds 150°C, the converter enters
•
•
Rev. 0 | Page 14 of 16
Place the inductor, input capacitor, and output capacitor
close to the IC using short tracks. These components carry
high switching frequencies, and large tracks act as antennas.
Route the output voltage path away from the inductor and
SW node to minimize noise and magnetic interference.
Maximize the size of ground metal on the component side
to help with thermal dissipation.
Use a ground plane with several vias connecting to the component side ground to further reduce noise interference on
sensitive circuit nodes.
ADP2147
EVALUATION BOARD
VIN GND
CONN PWR 2-P
2
VIN
1
VIN
TB1
J6
VIN
CIN
4.7µF
JP3
3
2
1
ADP2147
A1
VIN
C1
3
2
EN
1
ENABLE
A2
B2
VIN
GND
EN
SW
B1 1
L1
1µH
2
TB3
VOUT
U1
VOUT
C2
COUT
4.7µF
VSEL
JP2
3
2
1
3
2
1
VSEL
TB4
GND IN
GND OUT
09885-030
GND
TB5
Figure 35. Evaluation Board Schematic
Figure 36. Top Layer
09885-137
09885-136
EVALUATION BOARD LAYOUT
Figure 37. Bottom Layer
Rev. 0 | Page 15 of 16
ADP2147
OUTLINE DIMENSIONS
1.070
1.030
0.990
2
1
A
BALL A1
IDENTIFIER
1.545
1.505
1.465
1.00
REF
C
0.50
REF
TOP VIEW
(BALL SIDE DOWN)
0.50 REF
BOTTOM VIEW
0.370
0.355
0.340
SIDE VIEW
(BALL SIDE UP)
COPLANARITY
0.05
0.340
0.320
0.300
SEATING
PLANE
0.270
0.240
0.210
12-07-2010-A
0.640
0.595
0.550
B
Figure 38. 6-Ball Wafer Level Chip Scale Package [WLCSP]
(CB-6-12)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADP2147ACBZ-110-R7
ADP2147ACBZ-130-R7
ADP2147ACBZ-150-R7
ADP2147ACBZ-170-R7
ADP2147CB-110EVALZ
ADP2147CB-130EVALZ
ADP2147CB-150EVALZ
ADP2147CB-170EVALZ
1
Temperature
Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
VOUT (V)
(VSEL = 0)
1.275
0.9
1.2
0.9
VOUT (V)
(VSEL = 1)
0.981
1.3
1.0
1.1
Package Description
6-Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Wafer Level Chip Scale Package [WLCSP]
6-Ball Wafer Level Chip Scale Package [WLCSP]
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
Z = RoHS Compliant Part.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09885-0-5/11(0)
Rev. 0 | Page 16 of 16
Package
Option
CB-6-12
CB-6-12
CB-6-12
CB-6-12
Branding
LLE
LLF
LLG
LLH