AD LPS6225

1.2 A, 20 V, 700 kHz/1.4 MHz,
Nonsynchronous Step-Down Regulator
ADP2300/ADP2301
FEATURES
LDO replacement for digital load applications
Intermediate power rail conversion
Communications and networking
Industrial and instrumentation
Healthcare and medical
Consumer
3.0V TO 20V
BST
VIN
ADP2300/
ADP2301
ON
EN
VOUT
SW
FB
GND
08342-001
OFF
Figure 1.
100
fSW = 1.4MHz
fSW = 700kHz
95
90
85
80
75
70
65
60
VIN = 12V
VOUT = 5.0V
0
0.2
0.4
0.6
0.8
IOUT (A)
1.0
1.2
08342-069
APPLICATIONS
TYPICAL APPLICATIONS CIRCUIT
EFFICIENCY (%)
1.2 A maximum load current
±2% output accuracy over temperature range
Wide input voltage range: 3.0 V to 20 V
700 kHz (ADP2300) or 1.4 MHz (ADP2301)
switching frequency options
High efficiency up to 91%
Current-mode control architecture
Output voltage from 0.8 V to 0.85 × VIN
Automatic PFM/PWM mode switching
Precision enable pin with hysteresis
Integrated high-side MOSFET
Integrated bootstrap diode
Internal compensation and soft start
Minimum external components
Undervoltage lockout (UVLO)
Overcurrent protection (OCP) and thermal shutdown (TSD)
ADIsimPower™ online design tool
Available in ultrasmall, 6-lead TSOT package
Figure 2. Efficiency vs. Output Current
GENERAL DESCRIPTION
The ADP2300/ADP2301 are compact, constant-frequency,
current-mode, step-down dc-to-dc regulators with integrated
power MOSFET. The ADP2300/ADP2301 devices run from
input voltages of 3.0 V to 20 V, making them suitable for a wide
range of applications. A precise, low voltage internal reference
makes these devices ideal for generating a regulated output
voltage as low as 0.8 V, with ±2% accuracy, for up to 1.2 A load
current.
There are two frequency options: the ADP2300 runs at 700 kHz,
and the ADP2301 runs at 1.4 MHz. These options allow users to
make decisions based on the trade-off between efficiency and
total solution size. Current-mode control provides fast and stable
line and load transient performance. The ADP2300/ADP2301
devices include internal soft start to prevent inrush current at
power-up. Other key safety features include short-circuit protection, thermal shutdown (TSD), and input undervoltage lockout
(UVLO). The precision enable pin threshold voltage allows the
ADP2300/ADP2301 to be easily sequenced from other input/
output supplies. It can also be used as a programmable UVLO
input by using a resistive divider.
The ADP2300/ADP2301 are available in a 6-lead TSOT package
and are rated for the −40°C to +125°C junction temperature range.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
ADP2300/ADP2301
TABLE OF CONTENTS
Features .............................................................................................. 1 Thermal Shutdown .................................................................... 15 Applications ....................................................................................... 1 Control Loop............................................................................... 15 Typical Applications Circuit............................................................ 1 Applications Information .............................................................. 16 General Description ......................................................................... 1 Programming the Output Voltage ........................................... 16 Revision History ............................................................................... 2 Voltage Conversion Limitations ............................................... 16 Specifications..................................................................................... 3 Low Input Voltage Considerations .......................................... 17 Absolute Maximum Ratings............................................................ 4 Programming the Precision Enable ......................................... 17 Thermal Resistance ...................................................................... 4 Inductor ....................................................................................... 18 ESD Caution .................................................................................. 4 Catch Diode ................................................................................ 19 Pin Configuration and Function Descriptions ............................. 5 Input Capacitor ........................................................................... 19 Typical Performance Characteristics ............................................. 6 Output Capacitor........................................................................ 19 Functional Block Diagram ............................................................ 13 Thermal Considerations............................................................ 20 Theory of Operation ...................................................................... 14 Design Example .............................................................................. 21 Basic Operation .......................................................................... 14 Switching Frequency Selection ................................................. 21 PWM Mode ................................................................................. 14 Catch Diode Selection ............................................................... 21 Power Saving Mode .................................................................... 14 Inductor Selection ...................................................................... 21 Bootstrap Circuitry .................................................................... 14 Output Capacitor Selection....................................................... 21 Precision Enable ......................................................................... 14 Resistive Voltage Divider Selection.......................................... 22 Integrated Soft Start ................................................................... 14 Circuit Board Layout Recommendations ................................... 23 Current Limit .............................................................................. 14 Typical Application Circuits ......................................................... 24 Short-Circuit Protection ............................................................ 15 Outline Dimensions ....................................................................... 26 Undervoltage Lockout (UVLO) ............................................... 15 Ordering Guide .......................................................................... 26 REVISION HISTORY
2/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 28
ADP2300/ADP2301
SPECIFICATIONS
VIN = 3.3 V, TJ = −40°C to +125°C for minimum/maximum specifications, and TA = 25°C for typical specifications, unless otherwise noted.
Table 1.
Parameter
VIN
Voltage Range
Supply Current
Shutdown Current
Undervoltage Lockout Threshold
FB
Regulation Voltage
Bias Current
SW
On Resistance 1
Peak Current Limit 2
Minimum On Time
Minimum Off Time
Symbol
VIN
IVIN
ISHDN
UVLO
VFB
2
2.15
TJ = 0°C to +125°C
TJ = −40°C to +125°C
0.788
0.784
VBST − VSW = 5 V, ISW = 150 mA
VBST − VSW = 5 V, VIN = 12 V
1.5
0.5
1.0
VEN
VBOOT
Typ
Max
Unit
20
800
35
2.95
V
μA
μA
V
V
0.800
0.800
0.01
0.812
0.816
0.1
V
V
μA
440
1.9
100
145
70
0.7
1.4
1460
730
700
2.5
135
190
120
0.9
1.75
mΩ
A
ns
ns
ns
MHz
MHz
μs
μs
1.2
100
1.2
5.0
1.27
V
mV
μA
V
3
No switching, VIN = 12 V
VEN = 0 V, VIN = 12 V
VIN rising
VIN falling
ADP2300
ADP2301
ADP2300
ADP2301
ADP2300
ADP2301
SOFT START TIME
1
Min
IFB
OSCILLATOR FREQUENCY
EN
Input Threshold
Input Hysteresis
Pull-Down Current
BOOTSTRAP VOLTAGE
THERMAL SHUTDOWN
Threshold
Hysteresis
Test Conditions
1.13
No switching, VIN = 12 V
640
18
2.80
2.40
140
15
Pin-to-pin measurements.
Guaranteed by design.
Rev. 0 | Page 3 of 28
°C
°C
ADP2300/ADP2301
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VIN, EN
SW
BST to SW
BST
FB
Operating Junction Temperature Range
Storage Temperature Range
Soldering Conditions
THERMAL RESISTANCE
Rating
−0.3 V to +28 V
−1.0 V to +28 V
−0.6 V to +6 V
−0.3 V to +28 V
−0.3 V to +3.3 V
−40°C to +125°C
−65°C to +150°C
JEDEC J-STD-020
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance1
Package Type
6-Lead TSOT
1
θJA
186.02
θJC
66.34
Unit
°C/W
θJA and θJC are measured using natural convection on a JEDEC 4-layer board.
ESD CAUTION
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Absolute maximum ratings apply individually only, not in
combination. Unless otherwise specified, all voltages are
referenced to GND.
Rev. 0 | Page 4 of 28
ADP2300/ADP2301
BST
1
GND
2
FB
3
ADP2300/
ADP2301
TOP VIEW
(Not to Scale)
6
SW
5
VIN
4
EN
08342-002
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
BST
2
3
GND
FB
4
EN
5
6
VIN
SW
Description
Boost Supply for the High-Side MOSFET Driver. A 0.1 μF capacitor is connected between the SW and BST pins
to form a floating supply to drive the gate of the MOSFET switch above the VIN supply voltage.
Ground. Connect this pin to the ground plane.
Feedback Voltage Sense Input. Connect this pin to a resistive divider from VOUT. Set the voltage to 0.8 V for a
desired VOUT.
Output Enable. Pull this pin high to enable the output. Pull this pin low to disable the output. This pin can
also be used as a programmable UVLO input. This pin has a 1.2 μA pull-down current to GND.
Power Input. Connect to the input power source with a ceramic bypass capacitor to GND directly from this pin.
Switch Node Output. Connect an inductor to VOUT and a catch diode to GND from this pin.
Rev. 0 | Page 5 of 28
ADP2300/ADP2301
TYPICAL PERFORMANCE CHARACTERISTICS
100
90
90
80
80
70
60
VOUT = 12V
VOUT = 9V
VOUT = 5.0V
VOUT = 3.3V
INDUCTOR: LPS6225-472MLC
DIODE: B230A
0
0.2
0.4
0.6
0.8
60
VOUT
VOUT
VOUT
VOUT
VOUT
50
1.0
1.2
IOUT (A)
40
0
90
80
80
EFFICIENCY (%)
90
70
60
0
0.2
0.4
0.6
VOUT = 12V
VOUT = 9V
VOUT = 5.0V
VOUT = 3.3V
0.8
1.0
1.2
IOUT (A)
50
40
VOUT = 2.5V
VOUT = 1.8V
VOUT = 1.2V
0
80
EFFICIENCY (%)
80
70
60
0.4
0.6
0.8
1.0
IOUT (A)
0.6
0.8
1.0
1.2
1.2
INDUCTOR: LPS6225-103MLC
DIODE: B230A
70
60
50
VOUT = 5.0V
VOUT = 3.3V
VOUT = 2.5V
08342-072
EFFICIENCY (%)
90
0.2
0.4
Figure 8. Efficiency Curve, VIN = 5.0 V, fSW = 1.4 MHz
90
0
0.2
IOUT (A)
100
40
1.2
60
100
INDUCTOR: LPS6225-472MLC
DIODE: B230A
1.0
INDUCTOR: LPS6225-472MLC
DIODE: B230A
Figure 5. Efficiency Curve, VIN = 18 V, fSW = 700 kHz
50
0.8
70
08342-071
EFFICIENCY (%)
100
40
0.6
Figure 7. Efficiency Curve, VIN = 12 V, fSW = 700 kHz
100
INDUCTOR: LPS6225-103MLC
DIODE: B230A
0.4
IOUT (A)
Figure 4. Efficiency Curve, VIN = 18 V, fSW = 1.4 MHz
50
0.2
= 5.0V
= 3.3V
= 2.5V
= 1.8V
= 1.2V
08342-074
40
70
Figure 6. Efficiency Curve, VIN = 12 V, fSW = 1.4 MHz
40
VOUT = 2.5V
VOUT = 1.8V
VOUT = 1.2V
0
0.2
0.4
0.6
0.8
1.0
IOUT (A)
Figure 9. Efficiency Curve, VIN = 5.0 V, fSW = 700 kHz
Rev. 0 | Page 6 of 28
1.2
08342-075
50
INDUCTOR: LPS6225-103MLC
DIODE: B230A
08342-073
EFFICIENCY (%)
100
08342-070
EFFICIENCY (%)
VIN = 3.3 V, TA = 25°C, VEN = VIN, unless otherwise noted.
ADP2300/ADP2301
100
0.20
fSW = 1.4MHz
fSW = 700kHz
0.15
90
LINE REGULATION (%)
EFFICIENCY (%)
0.10
80
70
0.05
0
–0.05
60
–0.10
0
0.2
0.4
0.6
0.8
1.0
–0.20
1.2
IOUT (A)
08342-089
FREQUENCY (kHz)
20
fSW = 1.4MHz
fSW = 700kHz
70
60
1200
1000
800
600
INDUCTOR: LPS6225-103MLC
DIODE: B230A
0.2
0.4
0.6
0.8
1.0
1.2
IOUT (A)
400
–50
08342-066
0
–20
10
40
70
130
20
TEMPERATURE (°C)
Figure 14. Frequency vs. Temperature
Figure 11. Efficiency Curve, VIN = 3.3 V with External 5.0 V Bootstrap Bias
Voltage, fSW = 700 kHz
1600
0.20
fSW = 1.4MHz
fSW = 700kHz
FSW = 1.4MHz
FSW = 700kHz
0.15
100
08342-076
EFFICIENCY (%)
17
1400
50
1400
FREQUENCY (kHz)
0.10
0.05
0
–0.05
1200
1000
800
–0.10
600
–0.15
–0.20
0
0.2
0.4
0.6
0.8
1.0
IOUT (A)
1.2
400
08342-067
LOAD REGULATION (%)
14
1600
80
40
11
Figure 13. Line Regulation, VOUT = 3.3 V, IOUT = 500 mA
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
90
8
VIN (V)
Figure 10. Efficiency Curve, VIN = 3.3 V with External 5.0 V Bootstrap Bias
Voltage, fSW = 1.4 MHz
100
5
08342-077
40
–0.15
VOUT = 1.8V
VOUT = 1.2V
VOUT = 0.8V
INDUCTOR: LPS6225-472MLC
DIODE: B230A
08342-068
50
Figure 12. Load Regulation, VOUT = 3.3 V, VIN = 12 V
2
5
8
11
14
VIN (V)
Figure 15. Frequency vs. VIN
Rev. 0 | Page 7 of 28
17
160
35
140
30
120
MINIMUM OFF TIME (ns)
40
25
20
15
10
TJ = −40°C
TJ = +25°C
TJ = +125°C
5
8
11
14
17
80
60
40
20
20
VIN (V)
0
–50
–20
100
130
20
130
2.5
0.802
2.0
CURRENT LIMIT (A)
0.8V FEEDBACK VOLTAGE (V)
70
Figure 19. Minimum Off Time vs. Temperature
0.804
0.800
0.798
0.796
1.5
1.0
0.5
0.794
–20
10
40
70
100
130
TEMPERATURE (°C)
0
08342-079
0.792
–50
2
5
8
11
14
17
VIN (V)
Figure 17. 0.8 V Feedback Voltage vs. Temperature
Figure 20. Current-Limit Threshold vs. VIN, VBST − VSW = 5.0 V
110
2.5
105
CURRENT LIMIT (A)
2.0
100
95
90
1.5
1.0
0.5
85
–20
10
40
70
100
TEMPERATURE (°C)
130
08342-080
MINIMUM ON TIME (ns)
40
TEMPERATURE (°C)
Figure 16. Shutdown Current vs. VIN
80
–50
10
08342-081
2
100
08342-082
0
fSW = 1.4MHz
fSW = 700kHz
08342-083
5
08342-078
SHUTDOWN CURRENT (µA)
ADP2300/ADP2301
Figure 18. Minimum On Time vs. Temperature
0
–50
–20
10
40
70
100
TEMPERATURE (°C)
Figure 21. Current-Limit Threshold vs. Temperature
Rev. 0 | Page 8 of 28
ADP2300/ADP2301
700
3.0
RISING
FALLING
2.9
UVLO THRESHOLD (V)
2.8
620
580
540
2.6
2.5
2.4
2.3
2
5
8
11
14
17
2.1
20
VIN (V)
2.0
–50
–20
10
40
70
100
130
TEMPERATURE (°C)
Figure 22. Quiescent Current vs. VIN
Figure 25. UVLO Threshold vs. Temperature
900
800
VOUT
MOSFET RDS (ON) (mΩ)
700
1
IL
600
500
SW
400
4
300
200
10
40
70
100
130
TEMPERATURE (°C)
CH1 5mV
Figure 23. MOSFET RDS(ON) vs. Temperature (Pin-to-Pin Measurements)
B
W
B
CH2 5V
M400ns
W
CH4 500mA Ω BW
A CH2
7.4V
08342-024
–20
08342-085
0
–50
2
VGS = 5V
VGS = 4V
VGS = 3V
100
Figure 26. Steady State at Heavy Load, fSW = 1.4 MHz, IOUT = 1 A
1.30
RISING
FALLING
1.25
VOUT
1.20
1.15
IL
4
1.10
SW
1.05
–20
10
40
70
100
TEMPERATURE (°C)
130
CH1 20mV
B
W
B
CH2 5V
W M10µs
CH4 200mA Ω BW
A CH2
8V
08342-025
2
1.00
–50
08342-086
ENABLE THRESHOLD (V)
1
Figure 27. Steady State at Light Load, fSW = 1.4 MHz, IOUT = 40 mA
Figure 24. Enable Threshold vs. Temperature
Rev. 0 | Page 9 of 28
08342-087
500
2.7
2.2
TJ = −40°C
TJ = +25°C
TJ = +125°C
08342-084
QUIESCENT CURRENT (µA)
660
ADP2300/ADP2301
VOUT
VOUT
1
IL
IOUT
1
4
EN
SW
4
SW
3
2
B
W
B
W
B
CH2 10V
W M100µs
CH4 500mA Ω BW
A CH3
8V
CH1 50mV
Figure 28. Soft Start with 1 A Resistance Load, fSW = 1.4 MHz
B
W
B
CH2 10V
W M100µs A CH4
CH4 500mA Ω BW
630mA
08342-058
CH1 1V
CH3 10V
08342-026
2
Figure 31. ADP2301 Load Transient, 0.2 A to 1.0 A, VOUT = 3.3 V, VIN = 12 V
(fSW = 1.4 MHz, L = 4.7 μH, COUT = 22 μF)
VOUT
VOUT
1
1
IOUT
IL
4
EN
SW
4
SW
3
B
W
B
W
B
CH2 10V
W M100µs
CH4 500mA Ω BW
A CH3
8V
08342-027
CH1 1V
CH3 10V
CH1 200mV
W
B
CH2 10V
W M100µs A CH4
CH4 500mA Ω BW
630mA
Figure 32. ADP2300 Load Transient, 0.2 A to 1.0 A, VOUT = 5.0 V, VIN = 12 V
(fSW = 700 kHz, L = 10 μH, COUT = 22 μF)
Figure 29. Soft Start with No Load, fSW = 1.4 MHz
VOUT
VOUT
1
B
08342-059
2
2
1
IOUT
IOUT
4
SW
4
SW
B
W
B
CH2 10V
W M100µs A CH4
CH4 500mA Ω BW
580mA
08342-057
CH1 100mV
CH1 100mV
Figure 30. ADP2301 Load Transient, 0.2 A to 1.0 A, VOUT = 5.0 V, VIN = 12 V
(fSW = 1.4 MHz, L = 4.7 μH, COUT = 10 μF)
B
W
B
CH2 10V
W M100µs A CH4
CH4 500mA Ω BW
630mA
08342-060
2
2
Figure 33. ADP2300 Load Transient, 0.2 A to 1.0 A, VOUT = 3.3 V, VIN = 12 V
(fSW = 700 kHz, L = 10 μH, COUT = 22 μF)
Rev. 0 | Page 10 of 28
MAGNITUDE [B/A] (dB)
1
VIN
SW
11.4V
120
40
80
20
40
0
0
–20
–40
–40
–80
–60
–120
–80 CROSS FREQUENCY: 127kHz
PHASE MARGIN: 53°
–100
1
1k
10k
100k
FREQUENCY (Hz)
MAGNITUDE [B/A] (dB)
VOUT
1
IL
SW
CH1 1V
CH2 10V
CH4 1A Ω
B
W
B
W
M10µs
A CH1
2.56V
08342-033
2
B
W
200
80
160
60
120
40
80
20
40
0
0
–20
–40
–40
–80
–60
–120
–80 CROSS FREQUENCY: 80kHz
PHASE MARGIN: 68°
–100
1
1k
10k
100k
FREQUENCY (Hz)
MAGNITUDE [B/A] (dB)
VOUT
IL
SW
B
W
B
W
M100µs
A CH1
1.2V
08342-034
2
CH2 10V
CH4 1A Ω
–200
2
1M
100
200
80
160
60
120
40
80
20
40
0
0
–20
–40
–40
–80
–60
–120
–80
B
W
–160
Figure 38. ADP2301 Bode Plot, VOUT = 3.3 V, VIN = 12 V
(fSW = 1.4 MHz, L = 4.7 μH, COUT = 22 μF)
1
CH1 1V
1M
100
Figure 35. ADP2301 Short-Circuit Entry, VOUT = 3.3 V
(fSW = 1.4 MHz)
4
–200
2
Figure 37. ADP2301 Bode Plot, VOUT = 5.0 V, VIN = 12 V
(fSW = 1.4 MHz, L = 4.7 μH, COUT = 10 μF)
Figure 34. ADP2301 Line Transient,
7 V to 15 V, VOUT = 3.3 V, IOUT = 1.2 A, fSW = 1.4 MHz
4
–160
PHASE [B/A] (Degrees)
A CH3
60
08342-063
M1ms
160
–100
1k
Figure 36. ADP2301 Short-Circuit Recovery, VOUT = 3.3 V
(fSW = 1.4 MHz)
–160
CROSS FREQUENCY: 27kHz
PHASE MARGIN: 76°
1
10k
100k
FREQUENCY (Hz)
–200
2
1M
Figure 39. ADP2300 Bode Plot, VOUT = 5.0 V, VIN = 12 V
(fSW = 700 kHz, L = 10 μH, COUT = 22 μF)
Rev. 0 | Page 11 of 28
PHASE [B/A] (Degrees)
B
W
CH2 10V
80
08342-064
B
W
CH1 5mV
CH3 5V
08342-061
3
2
200
08342-062
VOUT
100
PHASE [B/A] (Degrees)
ADP2300/ADP2301
200
80
160
60
120
40
80
20
40
0
0
–20
–40
–40
–80
–60
–120
–80 CROSS FREQUENCY: 47kHz
PHASE MARGIN: 77°
–100
1
1k
10k
100k
FREQUENCY (Hz)
PHASE [B/A] (Degrees)
100
–160
–200
2
1M
08342-065
MAGNITUDE [B/A] (dB)
ADP2300/ADP2301
Figure 40. ADP2300 Bode Plot, VOUT = 3.3 V, VIN = 12 V
(fSW = 700 kHz, L = 10 μH, COUT = 22 μF)
Rev. 0 | Page 12 of 28
ADP2300/ADP2301
FUNCTIONAL BLOCK DIAGRAM
VIN
VIN
5
THERMAL
SHUTDOWN
SHUTDOWN
LOGIC
UVLO
SHUTDOWN IC
1.20V
OCP
EN 4
ON
1.2µA
OFF
OVP
250mV/A
BOOT
REGULATOR
0.5V
1
BST
0.90V
R
Q
VOUT
S
VBIAS = 1.1V
6
RAMP
GENERATOR
SW
CLK
GENERATOR
0.8V
VFB
3
220kΩ
2
0.7pF
GND
90pF
ADP2300/ADP2301
Figure 41. ADP2300/ADP2301 Functional Block Diagram
Rev. 0 | Page 13 of 28
08342-038
FB
FREQUENCY FOLDBACK
(fSW, ½ fSW, ¼ fSW)
ADP2300/ADP2301
THEORY OF OPERATION
The ADP2300/ADP2301 are nonsynchronous, step-down
dc-to-dc regulators, each with an integrated high-side power
MOSFET. A high switching frequency and ultrasmall, 6-lead
TSOT package allow small step-down dc-to-dc regulator
solutions.
Since the pulse-skip mode comparator monitors the internal
compensation node, which represents the peak inductor current
information, the average pulse-skip load current threshold depends
on the input voltage (VIN), the output voltage (VOUT), the inductor,
and the output capacitor.
The ADP2300/ADP2301 can operate with an input voltage from
3.0 V to 20 V while regulating an output voltage down to 0.8 V.
Because the output voltage occasionally dips below regulation
and then recovers, the output voltage ripple in the power saving
mode is larger than the ripple in the PWM mode of operation.
The ADP2300/ADP2301 are available in two fixed-frequency
options: 700 kHz (ADP2300) and 1.4 MHz (ADP2301).
BASIC OPERATION
The ADP2300/ADP2301 use the fixed-frequency, peak currentmode PWM control architecture at medium to high loads, but
shift to a pulse-skip mode control scheme at light loads to reduce
the switching power losses and improve efficiency. When the
devices operate in fixed-frequency PWM mode, output regulation
is achieved by controlling the duty cycle of the integrated MOSFET.
When the devices operate in pulse-skip mode at light loads, the
output voltage is controlled in a hysteretic manner with higher
output ripple. In this mode of operation, the regulator periodically
stops switching for a few cycles, thus keeping the conversion
losses minimal to improve efficiency.
BOOTSTRAP CIRCUITRY
The ADP2300/ADP2301 each have an integrated boot regulator,
which requires that a 0.1 μF ceramic capacitor (X5R or X7R) be
placed between the BST and SW pins to provide the gate drive
voltage for the high-side MOSFET. There must be at least a 1.2 V
difference between the BST and SW pins to turn on the high-side
MOSFET. This voltage should not exceed 5.5 V in case the BST
pin is supplied with an external voltage source through a diode.
The ADP2300/ADP2301 generate a typical 5.0 V bootstrap voltage
for a gate drive circuit by differentially sensing and regulating the
voltage between the BST and SW pins. A diode integrated on the
chip blocks the reverse voltage between the VIN and BST pins
when the MOSFET switch is turned on.
PWM MODE
PRECISION ENABLE
In PWM mode, the ADP2300/ADP2301 operate at a fixed
frequency, set by an internal oscillator. At the start of each
oscillator cycle, the MOSFET switch is turned on, sending a
positive voltage across the inductor. The inductor current
increases until the current-sense signal crosses the peak
inductor current threshold that turns off the MOSFET switch;
this threshold is set by the error amplifier output. During the
MOSFET off time, the inductor current declines through the
external diode until the next oscillator clock pulse starts a new
cycle. The ADP2300/ADP2301 regulate the output voltage by
adjusting the peak inductor current threshold.
The ADP2300/ADP2301 feature a precision enable circuit that
has a 1.2 V reference voltage with 100 mV hysteresis. When the
voltage at the EN pin is greater than 1.2 V, the part is enabled. If the
EN voltage falls below 1.1 V, the chip is disabled. The precision
enable threshold voltage allows the ADP2300/ADP2301 to be
easily sequenced from other input/output supplies. It can also be
used as programmable UVLO input by using a resistive divider.
An internal 1.2 μA pull-down current prevents errors if the EN pin
is floating.
POWER SAVING MODE
To achieve higher efficiency, the ADP2300/ADP2301 smoothly
transition to the pulse-skip mode when the output load decreases
below the pulse-skip current threshold. When the output voltage
dips below regulation, the ADP2300/ADP2301 enter PWM mode
for a few oscillator cycles until the voltage increases to within
regulation. During the idle time between bursts, the MOSFET
switch is turned off, and the output capacitor supplies all the
output current.
INTEGRATED SOFT START
The ADP2300/ADP2301 include internal soft start circuitry
that ramps the output voltage in a controlled manner during
startup, thereby limiting the inrush current. The soft start time is
typically fixed at 1460 μs for the ADP2300 and at 730 μs for the
ADP2301.
CURRENT LIMIT
The ADP2300/ADP2301 include current-limit protection circuitry
to limit the amount of positive current flowing through the highside MOSFET switch. The positive current limit on the power
switch limits the amount of current that can flow from the input
to the output.
Rev. 0 | Page 14 of 28
ADP2300/ADP2301
SHORT-CIRCUIT PROTECTION
UNDERVOLTAGE LOCKOUT (UVLO)
The ADP2300/ADP2301 include frequency foldback to prevent
output current runaway when there is a hard short on the output.
The switching frequency is reduced when the voltage at the FB pin
drops below a certain value, which allows more time for the
inductor current to decline, but increases the ripple current while
regulating the peak current. This results in a reduction in average
output current and prevents output current runaway. The correlation between the switching frequency and the FB pin voltage
is shown in Table 5.
The ADP2300/ADP2301 have fixed, internally set undervoltage
lockout circuitry. If the input voltage drops below 2.4 V, the
ADP2300/ADP2301 shut down and the MOSFET switch turns
off. After the voltage rises again above 2.8 V, the soft start
period is initiated, and the part is enabled.
Table 5. Correlation Between the Switching Frequency
and the FB Pin Voltage
FB Pin Voltage
VFB ≥ 0.6 V
0.6 V > VFB > 0.2 V
Switching Frequency
fSW
½ fSW
VFB ≤ 0.2 V
¼ fSW
THERMAL SHUTDOWN
If the ADP2300/ADP2301 junction temperature rises above 140°C,
the thermal shutdown circuit disables the chip. Extreme junction
temperature can be the result of high current operation, poor
circuit board design, or high ambient temperature. A 15°C
hysteresis is included so that when thermal shutdown occurs,
the ADP2300/ADP2301 do not return to operation until the onchip temperature drops below 125°C. After the devices recover
from thermal shutdown, a soft start is initiated.
CONTROL LOOP
When a hard short (VFB ≤ 0.2 V) is removed, a soft start cycle
is initiated to regulate the output back to its level during normal
operation, which helps to limit the inrush current and prevent
possible overshoot on the output voltage.
The ADP2300/ADP2301 are internally compensated to minimize
external component count and cost. In addition, the built-in
slope compensation helps to prevent subharmonic oscillations
when the ADP2300/ADP2301 operate at a duty cycle greater
than or close to 50%.
Rev. 0 | Page 15 of 28
ADP2300/ADP2301
APPLICATIONS INFORMATION
PROGRAMMING THE OUTPUT VOLTAGE
VOLTAGE CONVERSION LIMITATIONS
The output voltage of the ADP2300/ADP2301 is externally set by
a resistive voltage divider from the output voltage to the FB pin,
as shown in Figure 42. Suggested resistor values for the typical
output voltage setting are listed in Table 6. The equation for the
output voltage setting is
There are both lower and upper output voltage limitations for a
given input voltage due to the minimum on time, the minimum
off time, and the bootstrap dropout voltage.
⎛ R
VOUT = 0.800 V × ⎜⎜1 + FB1
⎝ R FB 2
⎞
⎟
⎟
⎠
VOUT (min) = t MIN -ON × f SW (max) × (V IN (max) + V D ) − V D
where:
VOUT is the output voltage.
RFB1 is the feedback resistor from VOUT to FB.
RFB2 is the feedback resistor from FB to GND.
ADP2300/
ADP2301
where:
VIN(max) is the maximum input voltage.
fSW(max) is the maximum switching frequency for the worst case.
tMIN-ON is the minimum controllable on time.
VD is the diode forward drop.
The upper limit of the output voltage is constrained by the minimum controllable off time, which can be as high as 120 ns in
the ADP2301 for the worst case. By considering the variation of
both the switching frequency and the input voltage, the equation
for the upper limit of the output voltage is
VOUT
RFB2
08342-039
RFB1
FB
The lower limit of the output voltage is constrained by the finite,
controllable minimum on time, which can be as high as 135 ns for
the worst case. By considering the variation of both the switching
frequency and the input voltage, the equation for the lower limit
of the output voltage is
VOUT (max) = (1 − t MIN -OFF × f SW (max) ) × (V IN (min) + VD ) − VD
Figure 42. Programming the Output Voltage Using a Resistive Voltage Divider
Table 6. Suggested Values for Resistive Voltage Divider
VOUT (V)
1.2
1.8
2.5
3.3
5.0
RFB1 (kΩ), ±1%
4.99
12.7
21.5
31.6
52.3
RFB2 (kΩ), ±1%
10
10.2
10.2
10.2
10
where:
VIN(min) is the minimum input voltage.
fSW(max) is the maximum switching frequency for the worst case.
VD is the diode forward drop.
tMIN-OFF is the minimum controllable off time.
In addition, the bootstrap circuit limits the minimum input
voltage for the desired output due to internal dropout voltage.
To attain stable operation at light loads and ensure proper startup
for the prebias condition, the ADP2300/ADP2301 require the
voltage difference between the input voltage and the regulated
output voltage (or between the input voltage and the prebias
voltage) to be greater than 2.1 V for the worst case. If the voltage
difference is smaller, the bootstrap circuit relies on some minimum
load current to charge the boost capacitor for startup. Figure 43
shows the typical required minimum input voltage vs. load current
for the 3.3 V output voltage.
Rev. 0 | Page 16 of 28
ADP2300/ADP2301
5.5
PROGRAMMING THE PRECISION ENABLE
5.3
FOR STARTUP
Generally, the EN pin can be easily tied to the VIN pin so that the
device automatically starts up when the input power is applied.
However, the precision enable feature allows the ADP2300/
ADP2301 to be used as a programmable UVLO by connecting
a resistive voltage divider to VIN, as shown in Figure 46. This
configuration prevents the start-up problems that can occur
when VIN ramps up slowly in soft start with a relatively high
load current.
5.1
4.9
MINIMUM VIN (V)
4.7
4.5
4.3
4.1
FOR RUNNING
3.9
VIN
3.7
3.5
VOUT = 3.3V
fSW = 1.4MHz
1
10
100
VIN
ADP2300/
ADP2301
REN1
1k
LOAD CURRENT (mA)
08342-043
EN
Figure 43. Minimum Input Voltage vs. Load Current
REN2
Based on three conversion limitations (the minimum on time,
the minimum off time, and the bootstrap dropout
voltage), Figure 44 shows the voltage conversion limitations.
22
Figure 46. Precision Enable Used as a Programmable UVLO
The precision enable feature also allows the ADP2300/ADP2301 to
be sequenced precisely by using a resistive voltage divider with
another dc-to-dc output supply, as shown in Figure 47.
ADP2300/
ADP2301
12
OTHER DC-TO-DC
OUTPUT
REN1
EN
REN2
Figure 47. Precision Enable Used as a Sequencing Control
from Another DC-to-DC Output
7
MAXIMUM INPUT FOR ADP2300
MAXIMUM INPUT FOR ADP2301
MINIMUM INPUT FOR ADP2300/ADP2301
0
2
4
6
8
10
12
14
16
VOUT (V)
08342-055
2
08342-044
VIN (V)
17
With a 1.2 μA pull-down current on the EN pin, the equation for
the start-up voltage in Figure 46 and Figure 47 is
⎛ 1 .2 V
⎞
+ 1.2 μA ⎟⎟ × R EN 1 + 1.2 V
VSTARTUP = ⎜⎜
R
⎝ EN 2
⎠
Figure 44. Voltage Conversion Limitations
LOW INPUT VOLTAGE CONSIDERATIONS
For low input voltage between 3 V and 5 V, the internal boot
regulator cannot provide enough 5.0 V bootstrap voltage due to
the internal dropout voltage. As a result, the increased MOSFET
RDS(ON) reduces the available load current. To prevent this, add
an external small-signal Schottky diode from a 5.0 V external
bootstrap bias voltage. Because the absolute maximum rating
between the BST and SW pins is 6.0 V, the bias voltage should
be less than 5.5 V. Figure 45 shows the application diagram for
the external bootstrap circuit.
where:
VSTARTUP is the start-up voltage to enable the chip.
REN1 is the resistor from the dc source to EN.
REN2 is the resistor from EN to GND.
SCHOTTKY DIODE
3V ~ 5V
BST
VIN
5V BIAS
VOLTAGE
ADP2300/
ADP2301
ON
OFF
EN
GND
FB
08342-042
SW
Figure 45. External Bootstrap Circuit for Low Input Voltage Application
Rev. 0 | Page 17 of 28
ADP2300/ADP2301
INDUCTOR
The high switching frequency of the ADP2300/ADP2301 allows
the use of small inductors. For best performance, use inductor
values between 2 μH and 10 μH for ADP2301, and use inductor
values between 2 μH and 22 μH for ADP2300.
The peak-to-peak inductor current ripple is calculated using the
following equation:
ΔI RIPPLE =
(V IN − VOUT ) ⎛ VOUT + V D
× ⎜⎜
L × f sw
⎝ V IN + V D
⎞
⎟
⎟
⎠
where:
fSW is the switching frequency.
L is the inductor value.
VD is the diode forward drop.
VIN is the input voltage.
VOUT is the output voltage.
Inductors of smaller values are usually smaller in size and less
expensive, but increase the ripple current and the output voltage
ripple. As a guideline, the inductor peak-to-peak current ripple
should typically be set to 30% of the maximum load current for
optimal transient response and efficiency. Therefore, the inductor
value is calculated using the following equation:
L=
(V IN − VOUT )
0.3 × I LOAD(max) × f sw
⎛V
+ VD
× ⎜⎜ OUT
+
V
⎝ IN V D
The inductor peak current is calculated using the following
equation:
I PEAK = I LOAD(max) +
ΔI RIPPLE
2
The minimum current rating of the inductor must be greater
than the inductor peak current. For ferrite core inductors with a
quick saturation characteristic, the inductor saturation current
rating should be higher than the switch current-limit threshold
to prevent the inductor from reaching its saturation point. Be
sure to validate the worst-case condition, in which there is a
shorted output, over the intended temperature range.
Inductor conduction losses are caused by the flow of current
through the inductor, which is associated with the internal dc
resistance (DCR). Larger sized inductors have smaller DCR and,
therefore, may reduce inductor conduction losses. However,
inductor core losses are also related to the core material and the
ac flux swing, which are affected by the peak-to-peak inductor ripple current. Because the ADP2300/ADP2301 are high
switching frequency regulators, shielded ferrite core materials
are recommended for their low core losses and low EMI. Some
recommended inductors are shown in Table 7.
⎞
⎟
⎟
⎠
where ILOAD(max) is the maximum load current.
Table 7. Recommended Inductors
Vendor
Coilcraft
Sumida
Cooper Bussmann
Toko
TDK
Value (μH)
4.7
6.8
10
4.7
4.7
6.8
6.8
10
4.7
6.8
10
4.7
6.8
10
4.7
6.8
10
Part No.
LPS6225-472MLC
LPS6225-682MLC
LPS6225-103MLC
CDRH5D28RHPNP-4R7N
CDRH5D16NP-4R7N
CDRH5D28RHPNP-6R8N
CDRH5D16NP-6R8N
CDRH5D28RHPNP-100M
SD53-4R7-R
SD53-6R8-R
DR73-100-R
B1077AS-4R7N
B1077AS-6R8N
B1077AS-100M
VLC5045T-4R7M
VLC5045T-6R8M
VLC5045T-100M
Rev. 0 | Page 18 of 28
DCR (mΩ)
65
95
105
43
64
61
84
93
39
59
65
34
40
58
34
46
66
ISAT (A)
3.1
2.7
2.1
3.7
2.15
3.1
1.8
2.45
2.1
1.85
2.47
2.6
2.3
1.8
3.3
2.7
2.1
Dimensions
L × W × H (mm)
6.0 × 6.0 × 2.4
6.0 × 6.0 × 2.4
6.0 × 6.0 × 2.4
6.2 × 6.2 × 3.0
5.8 × 5.8 × 1.8
6.2 × 6.2 × 3.0
5.8 × 5.8 × 1.8
6.2 × 6.2 × 3.0
5.2 × 5.2 × 3.0
5.2 × 5.2 × 3.0
7.6 × 7.6 × 3.5
7.6 × 7.6 × 4.0
7.6 × 7.6 × 4.0
7.6 × 7.6 × 4.0
5.0 × 5.0 × 4.5
5.0 × 5.0 × 4.5
5.0 × 5.0 × 4.5
ADP2300/ADP2301
CATCH DIODE
OUTPUT CAPACITOR
The catch diode conducts the inductor current during the off
time of the internal MOSFET. The average current of the diode
in normal operation is, therefore, dependent on the duty cycle
of the regulator as well as the output load current.
The output capacitor selection affects both the output voltage ripple
and the loop dynamics of the regulator. The ADP2300/ADP2301
are designed to operate with small ceramic capacitors that have low
equivalent series resistance (ESR) and equivalent series inductance
(ESL) and are, therefore, easily able to meet stringent output voltage
ripple specifications.
⎛ V
+ VD
I DIODE( AVG ) = ⎜⎜1 − OUT
V IN + V D
⎝
⎞
⎟ × I LOAD(max)
⎟
⎠
where VD is the diode forward drop.
The only reason to select a diode with a higher current rating than
necessary in normal operation is for the worst-case condition, in
which there is a shorted output. In this case, the diode current
increases up to the typical peak current-limit threshold. Be sure to
consult the diode data sheet to ensure that the diode can operate
well within the thermal and electrical limits.
The reverse breakdown voltage rating of the diode must be higher
than the highest input voltage and allow an appropriate margin
for the ringing that may be present on the SW node. A Schottky
diode is recommended for best efficiency because it has a low
forward voltage drop and fast switching speed. Table 8 provides
a list of recommended Schottky diodes.
Table 8. Recommended Schottky Diodes
Vendor
ON Semiconductor
Diodes Inc.
Vishay
Part No.
MBRS230LT3
MBRS240LT3
B230A
B240A
SL23
SS24
VRRM
(V)
30
40
30
40
30
40
IAVG
(A)
2
2
2
2
2
2
When the regulator operates in forced continuous conduction
mode, the overall output voltage ripple is the sum of the voltage
spike caused by the output capacitor ESR plus the voltage ripple
caused by charging and discharging the output capacitor.
⎛
1
ΔV RIPPLE = ΔI RIPPLE × ⎜⎜
+ ESRCOUT
×
8
f
sw × C OUT
⎝
⎞
⎟
⎟
⎠
Capacitors with lower ESR are preferable to guarantee low
output voltage ripple, as shown in the following equation:
ESR COUT ≤
ΔV RIPPLE
ΔI RIPPLE
Ceramic capacitors are manufactured with a variety of dielectrics,
each with different behavior over temperature and applied voltage.
X5R or X7R dielectrics are recommended for best performance,
due to their low ESR and small temperature coefficients. Y5V
and Z5U dielectrics are not recommended because of their poor
temperature and dc bias characteristics.
In general, most applications using the ADP2301 (1.4 MHz
switching frequency) require a minimum output capacitor value
of 10 μF, whereas most applications using the ADP2300 (700 kHz
switching frequency) require a minimum output capacitor value
of 20 μF. Some recommended output capacitors for VOUT ≤ 5.0 V
are listed in Table 9.
INPUT CAPACITOR
Table 9. Recommended Capacitors for VOUT ≤ 5.0 V
The input capacitor must be able to support the maximum input
operating voltage and the maximum rms input current. The
maximum rms input current flowing through the input
capacitor is ILOAD(max)/2. Select an input capacitor capable of
withstanding the rms input current for an application’s maximum load current using the following equation:
Vendor
Murata
TDK
I IN ( RMS) = I LOAD(max) × D × (1 − D)
where D is the duty cycle and is equal to
V
+ VD
D = OUT
V IN + V D
The recommended input capacitor is ceramic with X5R or X7R
dielectrics due to its low ESR and small temperature coefficients.
A capacitance of 10 μF should be adequate for most applications.
To minimize supply noise, place the input capacitor as close to
the VIN pin of the ADP2300/ADP2301 as possible.
Rev. 0 | Page 19 of 28
Value
10 μF, 6.3 V
22 μF, 6.3 V
10 μF, 6.3 V
22 μF, 6.3 V
Part No.
GRM31MR60J106KE19
GRM31CR60J226KE19
C3216X5R0J106K
C3216X5R0J226M
Dimensions
L × W × H (mm)
3.2 × 1.6 × 1.15
3.2 × 1.6 × 1.6
3.2 × 1.6 × 1.6
3.2 × 1.6 × 0.85
ADP2300/ADP2301
THERMAL CONSIDERATIONS
The ADP2300/ADP2301 store the value of the inductor current
only during the on time of the internal MOSFET. Therefore, a small
amount of power is dissipated inside the ADP2300/ADP2301
package, which reduces thermal constraints.
However, when the application is operating under maximum
load with high ambient temperature and high duty cycle, the
heat dissipated within the package may cause the junction
temperature of the die to exceed the maximum junction
temperature of 125°C. If the junction temperature exceeds
140°C, the regulator goes into thermal shutdown and recovers
when the junction temperature drops below 125°C.
The rise in temperature of the package is directly proportional
to the power dissipation in the package. The proportionality
constant for this relationship is the thermal resistance from the
junction of the die to the ambient temperature, as shown in the
following equation:
TR = θJA × PD
where:
TR is the rise in temperature of the package.
θJA is the thermal resistance from the junction of the die to the
ambient temperature of the package.
PD is the power dissipation in the package.
The junction temperature of the die is the sum of the ambient
temperature of the environment and the temperature rise of the
package due to power dissipation, as indicated in the following
equation:
TJ = TA + TR
where:
TJ is the junction temperature.
TA is the ambient temperature.
TR is the rise in temperature of the package due to power
dissipation.
Rev. 0 | Page 20 of 28
ADP2300/ADP2301
DESIGN EXAMPLE
This section provides the procedures to select the external components, based on the example specifications listed in Table 10.
The schematic for this design example is shown in Figure 48.
INDUCTOR SELECTION
Select the inductor by using the following equation:
L=
Table 10. Step-Down DC-to-DC Regulator Requirements
Parameter
Input Voltage, VIN
Output Voltage, VOUT
Programmable
UVLO Voltage
Specification
12.0 V ± 10%
3.3 V, 1.2 A, 1% VOUT
ripple at CCM mode
VIN start-up voltage
approximately 7.8 V
Additional
Requirements
None
None
None
0.3 × I LOAD(max) × f sw
⎛V
+ VD
× ⎜⎜ OUT
⎝ V IN + V D
⎞
⎟
⎟
⎠
where:
VOUT = 3.3 V.
VIN = 12 V.
ILOAD(max) = 1.2 A.
VD = 0.4 V.
fSW = 1.4 MHz.
This results in L = 5.15 μH. The closest standard value is 4.7 μH;
therefore, ΔIRIPPLE = 0.394 A.
SWITCHING FREQUENCY SELECTION
Select the switching frequency—700 kHz (ADP2300) or 1.4 MHz
(ADP2301)—using the conversion limitation curve shown
in Figure 44 to assess the conversion limitations (the minimum on
time, the minimum off time, and the bootstrap dropout voltage).
For example, in Figure 44 VIN = 12 V ± 10% is within the conversion limitation for both the 700 kHz and 1.4 MHz switching
frequencies for an output voltage of 3.3 V, but choosing the 1.4 MHz
switching frequency provides the smallest sized solution. If higher
efficiency is required, choose the 700 kHz option; however, the
PCB footprint area of the regulator will be larger because of the
bigger inductor and output capacitors.
CATCH DIODE SELECTION
Select the catch diode. A Schottky diode is recommended for best
efficiency because it has a low forward voltage drop and faster
switching speed. The average current of the catch diode in
normal operation, with a typical Schottky diode forward
voltage, can be calculated using the following equation:
⎛ V
+ VD
I DIODE ( AVG ) = ⎜⎜1 − OUT
V
VD
+
IN
⎝
(V IN − VOUT )
⎞
⎟
⎟ × I LOAD(max)
⎠
The inductor peak current is calculated using the following
equation:
I PEAK = I LOAD(max) +
ΔI RIPPLE
2
where:
ILOAD(max) = 1.2 A.
ΔIRIPPLE = 0.394 A.
Therefore, the calculated peak current for the inductor is 1.397 A.
However, to protect the inductor from reaching its saturation
point in the current-limit condition, the inductor should be rated
for at least a 2.0 A saturation current for reliable operation.
OUTPUT CAPACITOR SELECTION
Select the output capacitor based on the output voltage ripple
requirement, according to the following equation:
⎛
1
ΔV RIPPLE = ΔI RIPPLE × ⎜⎜
+ ESRCOUT
×
8
f
sw × C OUT
⎝
⎞
⎟
⎟
⎠
where:
ΔIRIPPLE = 0.394 A.
fSW = 1.4 MHz.
ΔVRIPPLE = 33 mV.
where:
VOUT = 3.3 V.
VIN = 12 V.
ILOAD(max) = 1.2 A.
VD = 0.4 V.
If the ESR of the ceramic capacitor is 3 mΩ, then COUT = 1.2 μF.
Therefore, IDIODE(AVG) = 0.85 A.
However, for the worst-case condition, in which there is a shorted
output, the diode current would be increased to 2 A typical, determined by the peak switch current limit (see Table 1). In this case,
selecting a B230A, 2.0 A/30 V surface-mount Schottky diode
would result in more reliable operation.
Because the output capacitor is one of the two external components
that control the loop stability, most applications using the ADP2301
(1.4 MHz switching frequency) require a minimum 10 μF capacitance to ensure stability. According to the recommended external
components in Table 11, choose 22 μF with a 6.3 V voltage rating
for this example.
Rev. 0 | Page 21 of 28
ADP2300/ADP2301
The resistive voltage divider for the programmable VIN start-up
voltage is
RESISTIVE VOLTAGE DIVIDER SELECTION
To select the appropriate resistive voltage divider, first calculate the
output feedback resistive voltage divider, and then calculate the
resistive voltage divider for the programmable VIN start-up voltage.
⎛ 1.2 V
⎞
+ 1.2 μA ⎟⎟ × R EN 1 + 1.2 V
VSTARTUP = ⎜⎜
⎝ R EN 2
⎠
The output feedback resistive voltage divider is
VOUT
⎛ R
= 0.800 V × ⎜⎜1 + FB1
⎝ R FB 2
If VSTARTUP = 7.8 V, choose REN2 = 10.2 kΩ, and then calculate
REN1, which in this case is 56 kΩ.
⎞
⎟
⎟
⎠
For the 3.3 V output voltage, choose RFB1 = 31.6 kΩ and RFB2
= 10.2 kΩ as the feedback resistive voltage divider, according to
the recommended values in Table 11.
BST
C3
0.1µF
6.3V
VIN
ADP2301
(1.4MHz)
SW
R3
56kΩ
1%
R4
10.2kΩ
1%
EN
FB
GND
D1
B230A
L1
4.7µH
2.0A
VOUT = 3.3V
1.2A
C2
22µF
6.3V
R1
31.6kΩ
1%
R2
10.2kΩ
1%
08342-045
VIN = 12V
C1
10µF
25V
Figure 48. Schematic for the Design Example
Table 11. Recommended External Components for Typical Applications at 1.2 A Output Load
Part Number
ADP2300 (700 kHz)
ADP2301 (1.4 MHz)
VIN (V)
18
18
12
12
12
12
12
9
9
5
5
18
18
12
12
12
9
9
5
5
VOUT (V)
3.3
5.0
1.2
1.8
2.5
3.3
5.0
3.3
5.0
1.8
2.5
3.3
5.0
2.5
3.3
5.0
3.3
5.0
1.8
2.5
IOUT (A)
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
L (μH)
10
15
6.8
6.8
10
10
10
10
10
4.7
4.7
4.7
6.8
4.7
4.7
4.7
4.7
4.7
2.2
2.2
Rev. 0 | Page 22 of 28
COUT (μF)
22
22
2 × 22
2 × 22
22
22
22
22
22
2 × 22
22
22
10
22
22
10
22
10
2 × 22
22
RFB1 (kΩ), ±1%
31.6
52.3
4.99
12.7
21.5
31.6
52.3
31.6
52.3
12.7
21.5
31.6
52.3
21.5
31.6
52.3
31.6
52.3
12.7
21.5
RFB2 (kΩ), ±1%
10.2
10
10
10.2
10.2
10.2
10
10.2
10
10.2
10.2
10.2
10
10.2
10.2
10
10.2
10
10.2
10.2
ADP2300/ADP2301
CIRCUIT BOARD LAYOUT RECOMMENDATIONS
•
Good circuit board layout is essential to obtain the best
performance from the ADP2300/ADP2301. Poor layout can
affect the regulation and stability, as well as the electromagnetic
interface (EMI) and electromagnetic compatibility (EMC)
performance. A PCB layout example is shown in Figure 50.
Refer to the following guidelines for a good PCB layout:
•
EN
FB
GND
08342-046
•
ADP2300/
ADP2301 SW
Place the input capacitor, inductor, catch diode, output
capacitor, and bootstrap capacitor close to the IC using
short traces.
Ensure that the high current loop traces are as short and wide
as possible. The high current path is shown in Figure 49.
Maximize the size of ground metal on the component side
to improve thermal dissipation.
Use a ground plane with several vias connecting to the
component side ground to further reduce noise interference on sensitive circuit nodes.
Figure 49. Typical Application Circuit with High Current Traces Shown in Blue
INDUC TOR
C3
L1
CA TCH DIODE
BST CA P
RFB2
D1
C1
C2
RFB1
ADP2300/ADP2301
INPUT CA P
Figure 50. Recommended PCB Layout for the ADP2300/ADP2301
Rev. 0 | Page 23 of 28
08342-056
•
BST
VIN
OUTPUT CAP
•
Minimize the length of the FB trace connecting the top of the
feedback resistive voltage divider to the output. In addition,
keep these traces away from the high current traces and the
switch node to avoid noise pickup.
ADP2300/ADP2301
TYPICAL APPLICATION CIRCUITS
BST
VIN
ADP2300
(700kHz)
R3
100kΩ
5%
EN
ON
C4
0.1µF L1
6.3V 6.8µH
2.0A
SW
D1
B230A
VOUT = 1.2V
1.2A
R1
4.99kΩ
1%
FB
C2
22µF
6.3V
C3
22µF
6.3V
R2
10kΩ
1%
GND
OFF
08342-052
VIN = 12V
C1
10µF
25V
Figure 51. ADP2300—700 kHz Typical Application, VIN = 12 V, VOUT = 1.2 V/1.2 A with External Enabling
BST
VIN
C1
10µF
25V
ADP2300
(700kHz)
C4
0.1µF
6.3V
EN
GND
VOUT = 1.8V
1.2A
SW
D1
B230A
R3
100kΩ
5%
ON
L1
6.8µH
2.0A
FB
R1
12.7kΩ
1%
C3
22µF
6.3V
C2
22µF
6.3V
R2
10.2kΩ
1%
OFF
08342-051
VIN = 12V
Figure 52. ADP2300—700 kHz Typical Application, VIN = 12 V, VOUT = 1.8 V/1.2 A with External Enabling
BST
VIN
C1
10µF
25V
ADP2300
(700kHz)
C3
0.1µF L1
6.3V 10µH
2.0A
SW
D1
B230A
R3
100kΩ
5%
EN
ON
FB
GND
OFF
R1
21.5kΩ
1%
R2
10.2kΩ
1%
VOUT = 2.5V
1.2A
C2
22µF
6.3V
08342-050
VIN = 12V
Figure 53. ADP2300—700 kHz Typical Application, VIN = 12 V, VOUT = 2.5 V/1.2 A with External Enabling
Rev. 0 | Page 24 of 28
ADP2300/ADP2301
BST
C3
0.1µF
6.3V L1
4.7µH
2.0V
VIN
ADP2301
(1.4MHz)
R3
56kΩ
1%
D1
B230A
C2
22µF
6.3V
R1
31.6kΩ
1%
FB
EN
R4
10.2kΩ
1%
VOUT = 3.3V
1.2A
SW
R2
10.2kΩ
1%
GND
08342-049
VIN = 12V
C1
10µF
25V
Figure 54. ADP2301—1.4 MHz Typical Application, VIN = 12 V, VOUT = 3.3 V/1.2 A
(with Programmable 7.8 V Start-Up Input Voltage)
BST
VIN
C1
10µF
25V
C3
0.1µF
L1
6.3V 4.7µH
2.0A
ADP2301
(1.4MHz)
D1
B230A
R3
100kΩ
5%
EN
C2
10µF
6.3V
R1
52.3kΩ
1%
FB
ON
VOUT = 5V
1.2A
SW
R2
10kΩ
1%
GND
OFF
08342-048
VIN = 12V
Figure 55. ADP2301—1.4 MHz Typical Application, VIN = 12 V, VOUT = 5.0 V/1.2 A with External Enabling
BST
VIN
C1
10µF
25V
C3
0.1µF L1
6.3V 6.8µH
2.0A
ADP2301
D1
B230A
R3
100kΩ
5%
EN
C2
10µF
6.3V
R1
52.3kΩ
1%
FB
ON
VOUT = 5.0V
1.2A
SW
(1.4MHz)
R2
10.2kΩ
1%
GND
OFF
08342-090
VIN = 18V
Figure 56. ADP2301—1.4 MHz Typical Application, VIN = 18 V, VOUT = 5.0 V/1.2 A with External Enabling
BST
VIN
C1
10µF
25V
C3
0.1µF L1
6.3V 4.7µH
2.0A
ADP2301
(1.4MHz)
D1
B230A
R3
100kΩ
5%
EN
ON
VOUT = 3.3V
1.2A
SW
C2
22µF
6.3V
R1
31.6kΩ
1%
FB
R2
10.2kΩ
1%
GND
OFF
08342-091
VIN = 9V
Figure 57. ADP2301—1.4 MHz Typical Application, VIN = 9 V, VOUT = 3.3 V/1.2 A with External Enabling
BST
VIN
C1
10µF
25V
ADP2301
(1.4MHz)
C4
0.1µF L1
6.3V 2.2µH
2.0A
SW
D1
B230A
R3
100kΩ
5%
EN
ON
FB
GND
OFF
R1
12.7kΩ
1%
R2
10.2kΩ
1%
VOUT = 1.8V
1.2A
C2
22µF
6.3V
C3
22µF
6.3V
08342-092
VIN = 5V
Figure 58. ADP2301—1.4 MHz Typical Application, VIN = 5 V, VOUT = 1.8 V/1.2 A with External Enabling
Rev. 0 | Page 25 of 28
ADP2300/ADP2301
OUTLINE DIMENSIONS
2.90 BSC
6
5
4
2.80 BSC
1.60 BSC
1
2
PIN 1
INDICATOR
3
0.95 BSC
1.90
BSC
*1.00 MAX
0.10 MAX
0.50
0.30
SEATING
PLANE
0.20
0.08
8°
4°
0°
*COMPLIANT TO JEDEC STANDARDS MO-193-AA WITH
THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS.
0.60
0.45
0.30
102808-A
*0.90
0.87
0.84
Figure 59. 6-Lead Thin Small Outline Transistor Package [TSOT]
(UJ-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADP2300AUJZ-R7
ADP2300-EVALZ
ADP2301AUJZ-R7
ADP2301-EVALZ
1
Switching
Frequency
700 kHz
Temperature Range
−40°C to +85°C
1.4 MHz
−40°C to +85°C
Package Description
6-Lead Thin Small Outline Transistor Package [TSOT]
Evaluation Board
6-Lead Thin Small Outline Transistor Package [TSOT]
Evaluation Board
Z = RoHS Compliant Part.
Rev. 0 | Page 26 of 28
Package
Option
UJ-6
Branding
L87
UJ-6
L86
ADP2300/ADP2301
NOTES
Rev. 0 | Page 27 of 28
ADP2300/ADP2301
NOTES
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08342-0-2/10(0)
Rev. 0 | Page 28 of 28